On Wed 03 Aug 02:46 CDT 2022, Shinjo Park wrote:
> Use the same USB definition as qcom-apq8064.dtsi, tested on Casio GzOne.
>
I think this looks good, but I have a v2 of patch 1 and a v3 of patch 2,
and I don't seem to have patch 3 in my inbox(?)
Can you please resubmit the 3 patches with a --cover-letter, instead of
each patch being a reply of the previous instance of that particular
patch? This will make it much easier for me to merge the end result.
Thanks,
Bjorn
> Signed-off-by: Shinjo Park <peremen@xxxxxxxxx>
> Reviewed-by: David Heidelberg <david@xxxxxxx>
> ---
>
> v3:
> - Include missing clock/qcom,lcc-msm8960.h to make cleanly applicable
>
> v2:
> - Rewrite commit message
> - Reorder status line
>
> arch/arm/boot/dts/qcom-msm8960.dtsi | 33 +++++++++++++++++++++++++++++
> 1 file changed, 33 insertions(+)
>
> diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
> index e14e1c5d1..0e099aa7c 100644
> --- a/arch/arm/boot/dts/qcom-msm8960.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
> @@ -3,6 +3,8 @@
>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,gcc-msm8960.h>
> +#include <dt-bindings/clock/qcom,lcc-msm8960.h>
> +#include <dt-bindings/reset/qcom,gcc-msm8960.h>
> #include <dt-bindings/mfd/qcom-rpm.h>
> #include <dt-bindings/soc/qcom,gsbi.h>
>
> @@ -167,6 +169,37 @@ regulators {
> };
> };
>
> + usb1: usb@12500000 {
> + compatible = "qcom,ci-hdrc";
> + reg = <0x12500000 0x200>,
> + <0x12500200 0x200>;
> + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
> + clock-names = "core", "iface";
> + assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
> + assigned-clock-rates = <60000000>;
> + resets = <&gcc USB_HS1_RESET>;
> + reset-names = "core";
> + phy_type = "ulpi";
> + ahb-burst-config = <0>;
> + phys = <&usb_hs1_phy>;
> + phy-names = "usb-phy";
> + #reset-cells = <1>;
> + status = "disabled";
> +
> + ulpi {
> + usb_hs1_phy: phy {
> + compatible = "qcom,usb-hs-phy-msm8960",
> + "qcom,usb-hs-phy";
> + clocks = <&sleep_clk>, <&cxo_board>;
> + clock-names = "sleep", "ref";
> + resets = <&usb1 0>;
> + reset-names = "por";
> + #phy-cells = <0>;
> + };
> + };
> + };
> +
> acc0: clock-controller@2088000 {
> compatible = "qcom,kpss-acc-v1";
> reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
> --
> 2.34.1
>
