Re: [PATCH v6 2/2] arm64: dts: qcom: sc7280: add lpass lpi pin controller node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Apr 05, 2022 at 10:14:20AM -0700, Matthias Kaehlcke wrote:
> On Tue, Apr 05, 2022 at 04:42:47PM +0530, Srinivasa Rao Mandadapu wrote:
> > Add LPASS LPI pinctrl node required for Audio functionality on sc7280
> > based platforms.
> > 
> > Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@xxxxxxxxxxx>
> > Co-developed-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
> > Signed-off-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
> > ---
> >  arch/arm64/boot/dts/qcom/sc7280-idp.dtsi |  98 ++++++++++++++++++++++++++++
> >  arch/arm64/boot/dts/qcom/sc7280.dtsi     | 107 +++++++++++++++++++++++++++++++
> >  2 files changed, 205 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > index 2afbbe3..f912a89 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > @@ -238,6 +238,104 @@
> >  	modem-init;
> >  };
> >  
> > +&lpass_tlmm {
> > +	dmic01_active: dmic01-active {
> > +		clk {
> > +			drive-strength = <8>;
> > +		};
> > +
> > +		data {
> > +			drive-strength = <8>;
> 
> The DMIC data pins are input pins, right? Why does an input pin need a drive
> strength? Same for other input pins.
> 
> > +		};
> > +	};
> 
> There's no need to reference 'lpass_tlmm' nor to repeat $label: $node.
> Instead just use phandles:
> 
> &dmic01_active {
> 	clk {
> 		drive-strength = <8>;
> 	};
> 
> 	data {
> 		drive-strength = <8>;
> 	};
> };
> 
> Rather than replicating the node hierarchy you could also just give each pin a
> label, and then:
> 
> &dmic01_clk_active {
> 	drive-strength = <8>;
> };
> 
> &dmic01_data_active {
> 	drive-strength = <8>;
> };
> 
> I don't have a strong preference, but wonder if the grouping adds any value.

One more thing: please also drop the '_active' suffix, it is not needed. With
that I think it's clearer to get rid of the grouping.

> > +
> > +	dmic01_sleep: dmic01-sleep {
> > +		clk {
> > +			drive-strength = <2>;
> > +			bias-disable;
> > +		};
> > +
> > +		data {
> > +			drive-strength = <2>;
> > +			pull-down;
> > +		};
> > +	};
> > +
> > +	dmic23_active: dmic02-active {
> > +		clk {
> > +			drive-strength = <8>;
> > +		};
> > +
> > +		data {
> > +			drive-strength = <8>;
> > +		};
> > +	};
> > +
> > +	dmic23_sleep: dmic02-sleep {
> > +		clk {
> > +			drive-strength = <2>;
> > +			bias-disable;
> > +		};
> > +
> > +		data {
> > +			drive-strength = <2>;
> > +			pull-down;
> > +		};
> > +	};
> > +
> > +	rx_swr_active: rx-swr-active {
> > +		clk {
> > +			drive-strength = <2>;
> > +			slew-rate = <1>;
> > +			bias-disable;
> > +		};
> > +
> > +		data {
> > +			drive-strength = <2>;
> > +			slew-rate = <1>;
> > +			bias-bus-hold;
> > +		};
> > +	};
> > +
> > +	rx_swr_sleep: rx-swr-sleep {
> > +		clk {
> > +			drive-strength = <2>;
> > +			bias-pull-down;
> > +		};
> > +
> > +		data {
> > +			drive-strength = <2>;
> > +			bias-pull-down;
> > +		};
> > +	};
> > +
> > +	tx_swr_active: tx-swr-active {
> > +		clk {
> > +			drive-strength = <2>;
> > +			slew-rate = <1>;
> > +			bias-disable;
> > +		};
> > +
> > +		data {
> > +			drive-strength = <2>;
> > +			slew-rate = <1>;
> > +			bias-bus-hold;
> > +		};
> > +	};
> > +
> > +	tx_swr_sleep: tx-swr-sleep {
> > +		clk {
> > +			drive-strength = <2>;
> > +			bias-pull-down;
> > +		};
> > +
> > +		data {
> > +			drive-strength = <2>;
> > +			bias-bus-hold;
> > +		};
> > +	};
> > +};
> > +
> >  &pcie1 {
> >  	status = "okay";
> >  	perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
> > diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > index 8d8cec5..db74fc3 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > @@ -1987,6 +1987,113 @@
> >  			qcom,bcm-voters = <&apps_bcm_voter>;
> >  		};
> >  
> > +		lpass_tlmm: pinctrl@33c0000 {
> > +			compatible = "qcom,sc7280-lpass-lpi-pinctrl";
> > +			reg = <0 0x33c0000 0x0 0x20000>,
> > +				<0 0x3550000 0x0 0x10000>;
> 
> Pad addresses to 8 digits.
> 
> > +			gpio-controller;
> > +			#gpio-cells = <2>;
> > +			gpio-ranges = <&lpass_tlmm 0 0 15>;
> > +
> > +			#clock-cells = <1>;
> > +
> > +			dmic01_active: dmic01-active {
> > +				clk {
> > +					pins = "gpio6";
> > +					function = "dmic1_clk";
> > +				};
> > +
> > +				data {
> > +					pins = "gpio7";
> > +					function = "dmic1_data";
> > +				};
> > +			};
> > +
> > +			dmic01_sleep: dmic01-sleep {
> > +				clk {
> > +					pins = "gpio6";
> > +					function = "dmic1_clk";
> > +				};
> > +
> > +				data {
> > +					pins = "gpio7";
> > +					function = "dmic1_data";
> > +				};
> > +			};
> > +
> > +			dmic23_active: dmic02-active {
> 
> is it intentional that the node name is 'dmic02*', but the label 'dmic23*'?
> 
> > +				clk {
> > +					pins = "gpio8";
> > +					function = "dmic2_clk";
> > +				};
> > +
> > +				data {
> > +					pins = "gpio9";
> > +					function = "dmic2_data";
> > +				};
> > +			};
> > +
> > +			dmic23_sleep: dmic02-sleep {
> 
> ditto
> 
> > +				clk {
> > +					pins = "gpio8";
> > +					function = "dmic2_clk";
> > +				};
> > +
> > +				data {
> > +					pins = "gpio9";
> > +					function = "dmic2_data";
> > +				};
> > +			};
> > +
> > +			rx_swr_active: rx-swr-active {
> > +				clk {
> > +					pins = "gpio3";
> > +					function = "swr_rx_clk";
> > +				};
> > +
> > +				data {
> > +					pins = "gpio4", "gpio5";
> > +					function = "swr_rx_data";
> > +				};
> > +			};
> > +
> > +			rx_swr_sleep: rx-swr-sleep {
> > +				clk {
> > +					pins = "gpio3";
> > +					function = "swr_rx_clk";
> > +				};
> > +
> > +				data {
> > +					pins = "gpio4", "gpio5";
> > +					function = "swr_rx_data";
> > +				};
> > +			};
> > +
> > +			tx_swr_active: tx-swr-active {
> > +				clk {
> > +					pins = "gpio0";
> > +					function = "swr_tx_clk";
> > +				};
> > +
> > +				data {
> > +					pins = "gpio1", "gpio2", "gpio14";
> > +					function = "swr_tx_data";
> > +				};
> > +			};
> > +
> > +			tx_swr_sleep: tx-swr-sleep {
> > +				clk {
> > +					pins = "gpio0";
> > +					function = "swr_tx_clk";
> > +				};
> > +
> > +				data {
> > +					pins = "gpio1", "gpio2", "gpio14";
> > +					function = "swr_tx_data";
> > +				};
> > +			};
> > +		};
> > +
> >  		gpu: gpu@3d00000 {
> >  			compatible = "qcom,adreno-635.0", "qcom,adreno";
> >  			reg = <0 0x03d00000 0 0x40000>,



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux