From: "Ivan T. Ivanov" <iivanov@xxxxxxxxxx>
DT binding documentation for qcom,pm8xxx-mpp pinctrl drivers.
Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
---
.../bindings/pinctrl/qcom,pm8xxx-mpp.txt | 199 +++++++++++++++++++++
1 file changed, 199 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,pm8xxx-mpp.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pm8xxx-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pm8xxx-mpp.txt
new file mode 100644
index 0000000..a797d41
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pm8xxx-mpp.txt
@@ -0,0 +1,199 @@
+Qualcomm PM8XXX Multi-Purpose Pin (MPP) block
+
+This binding describes the MPP block(s) found in the 8xxx series of pmics from
+Qualcomm.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8841-mpp"
+ "qcom,pm8941-mpp"
+ "qcom,pma8084-mpp"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: Register base of the gpio block
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Must contain an array of encoded interrupt specifiers for
+ each available gpio
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: Mark the device node as a GPIO controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Must be 2;
+ the first cell will be used to define gpio number and the
+ second denotes the flags for this gpio
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin or a list of pins. This configuration can include the
+mux function to select on those pin(s), and various pin configuration
+parameters, s listed below.
+
+
+SUBNODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode. Valid pins are:
+ mpp1-mpp4 for pm8841
+ mpp1-mpp8 for pm8941
+ mpp1-mpp4 for pma8084
+
+- function:
+ Usage: mandatory
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Valid values are:
+ "gpio" - digital input, output
+ "ain" - analog input
+ "aout" - analog output
+ "cs" - current sink
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as no pull.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <u32>
+ Definition: The specified pins should be configued as pull up.
+ Valid values are 600, 10000 and 30000.
+
+- bias-high-impedance:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins will put in high-Z mode and disabled.
+
+- input-enable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are put in input mode.
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+
+- power-source:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the power source for the specified pins. Valid only
+ when pin operate in Digital I/O mode ("gpio"). Valid
+ power sources are, as defined in
+ <dt-bindings/pinctrl/qcom,pm8xxx-gpio.h>:
+ 0: (PM8XXX_GPIO_VIN0)
+ 1: (PM8XXX_GPIO_VIN1)
+ 2: (PM8XXX_GPIO_VIN2)
+ 3: (PM8XXX_GPIO_VIN3)
+ 4: (PM8XXX_GPIO_VIN4)
+ 5: (PM8XXX_GPIO_VIN5)
+ 6: (PM8XXX_GPIO_VIN6)
+ 7: (PM8XXX_GPIO_VIN7)
+
+- drive-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the drive strength for the specified pins. Value
+ drive strengths are: 5-40mA with 5mA step
+
+- qcom,ain:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the source for analog input. Valid values as
+ defined in <dt-bindings/pinctrl/qcom,pm8xxx-mpp.h>:
+ 0: (PM8XXX_MPP_AIN_CH5)
+ 1: (PM8XXX_MPP_AIN_CH6)
+ 2: (PM8XXX_MPP_AIN_CH7)
+ 3: (PM8XXX_MPP_AIN_CH8)
+ 4: (PM8XXX_MPP_AIN_ABUS1)
+ 5: (PM8XXX_MPP_AIN_ABUS2)
+ 6: (PM8XXX_MPP_AIN_ABUS3)
+ 7: (PM8XXX_MPP_AIN_ABUS4)
+
+- qcom,aout:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the analog output reference. Valid values as
+ defined in <dt-bindings/pinctrl/qcom,pm8xxx-mpp.h>:
+ 0: (PM8XXX_MPP_AOUT_1V25)
+ 1: (PM8XXX_MPP_AOUT_0V625)
+ 2: (PM8XXX_MPP_AOUT_0V3125)
+ 3: (PM8XXX_MPP_AOUT_MPP)
+ 4: (PM8XXX_MPP_AOUT_ABUS1)
+ 5: (PM8XXX_MPP_AOUT_ABUS2)
+ 6: (PM8XXX_MPP_AOUT_ABUS3)
+ 7: (PM8XXX_MPP_AOUT_ABUS4)
+
+Example:
+
+ mpps@a000 {
+ compatible = "qcom,pm8841-mpp";
+ reg = <0xa000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pm8841_default>;
+ pinctrl-1 = <&pm8841_sleep>;
+
+ pm8841_sleep: sleep {
+ gpio {
+ pins = "mpp1", "mpp2", "mpp3", "mpp4";
+ function = "gpio";
+
+ input-enable;
+
+ power-source = <PM8XXX_GPIO_VIN0>;
+ qcom,pull-up = <PM8XXX_GPIO_STRENGTH_NO>;
+ qcom,strength = <PM8XXX_GPIO_PULL_UP_30>;
+ };
+ };
+
+ pm8841_default: default {
+ ain {
+ pins = "mpp1", "mpp2", "mpp3", "mpp4";
+ function = "ain";
+ };
+ };
+ };
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
