The Kconfig options DEBUG_MSM_UART1, DEBUG_MSM_UART2, DEBUG_MSM_UART3,
MSM_DEBUG_UART1, MSM_DEBUG_UART2 and MSM_DEBUG_UART3 are removed, but
they are still referenced in the following files:
arch/arm/mach-msm/io.c,
arch/arm/mach-msm/board-trout.c
arch/arm/mach-msm/board-trout-gpio.c
Fix this by updating the reference to the new Kconfig option.
Reported-by: Paul Bolle <pebolle@xxxxxxxxxx>
Signed-off-by: Georgi Djakov <gdjakov@xxxxxxxxxx>
---
Changes since v1:
- Fixed similar issue in board-trout.c and board-trout-gpio.c
Applies to next-20140526.
arch/arm/mach-msm/board-trout-gpio.c | 2 +-
arch/arm/mach-msm/board-trout.c | 2 +-
arch/arm/mach-msm/io.c | 6 ++----
3 files changed, 4 insertions(+), 6 deletions(-)
diff --git a/arch/arm/mach-msm/board-trout-gpio.c b/arch/arm/mach-msm/board-trout-gpio.c
index 87e1d01..e24930e 100644
--- a/arch/arm/mach-msm/board-trout-gpio.c
+++ b/arch/arm/mach-msm/board-trout-gpio.c
@@ -94,7 +94,7 @@ static int trout_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
}
static struct msm_gpio_chip msm_gpio_banks[] = {
-#if defined(CONFIG_MSM_DEBUG_UART1)
+#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9a00000)
/* H2W pins <-> UART1 */
TROUT_GPIO_BANK("MISC2", 0x00, TROUT_GPIO_MISC2_BASE, 0x40),
#else
diff --git a/arch/arm/mach-msm/board-trout.c b/arch/arm/mach-msm/board-trout.c
index 015d544..8369dfd 100644
--- a/arch/arm/mach-msm/board-trout.c
+++ b/arch/arm/mach-msm/board-trout.c
@@ -90,7 +90,7 @@ static void __init trout_map_io(void)
msm_map_common_io();
iotable_init(trout_io_desc, ARRAY_SIZE(trout_io_desc));
-#ifdef CONFIG_MSM_DEBUG_UART3
+#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9c00000)
/* route UART3 to the "H2W" extended usb connector */
writeb(0x80, TROUT_CPLD_BASE + 0x00);
#endif
diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c
index 34e0947..b042dca 100644
--- a/arch/arm/mach-msm/io.c
+++ b/arch/arm/mach-msm/io.c
@@ -57,8 +57,7 @@ static struct map_desc msm_io_desc[] __initdata = {
.length = MSM_SHARED_RAM_SIZE,
.type = MT_DEVICE,
},
-#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
- defined(CONFIG_DEBUG_MSM_UART3)
+#if defined(CONFIG_DEBUG_MSM_UART)
{
/* Must be last: virtual and pfn filled in by debug_ll_addr() */
.length = SZ_4K,
@@ -76,8 +75,7 @@ void __init msm_map_common_io(void)
* pages are peripheral interface or not.
*/
asm("mcr p15, 0, %0, c15, c2, 4" : : "r" (0));
-#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
- defined(CONFIG_DEBUG_MSM_UART3)
+#if defined(CONFIG_DEBUG_MSM_UART)
#ifdef CONFIG_MMU
debug_ll_addr(&msm_io_desc[size - 1].pfn,
&msm_io_desc[size - 1].virtual);
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
