Re: [PATCH v3 04/15] clocksource: Add ARM System timer driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



2015-03-27 9:36 GMT+01:00 Daniel Lezcano <daniel.lezcano@xxxxxxxxxx>:
> On 03/26/2015 09:19 PM, Maxime Coquelin wrote:
>>
>> Hi Daniel,
>>
>>    Thanks for the review. Please find my answers below.
>>
>> 2015-03-26 10:50 GMT+01:00 Daniel Lezcano <daniel.lezcano@xxxxxxxxxx>:
>>>
>>> On 03/12/2015 10:55 PM, Maxime Coquelin wrote:
>>>>
>>>>
>>>> From: Maxime Coquelin <mcoquelin.stm32@xxxxxxxxx>
>>>>
>>>> This patch adds clocksource support for ARMv7-M's System timer,
>>>> also known as SysTick.
>>>>
>>>> Signed-off-by: Maxime Coquelin <mcoquelin.stm32@xxxxxxxxx>
>>>
>>>
>>>
>>> Hi Maxime,
>>>
>>> the driver looks good. Three comments below.
>>>
>>>    -- Daniel
>>>
>>>
>
> [ ... ]
>
>
>>>> +static void __init system_timer_of_register(struct device_node *np)
>>>> +{
>>>> +       struct clk *clk;
>>>> +       void __iomem *base;
>>>> +       u32 rate = 0;
>>>> +       int ret;
>>>> +
>>>> +       base = of_iomap(np, 0);
>>>> +       if (!base) {
>>>> +               pr_warn("system-timer: invalid base address\n");
>>>> +               return;
>>>> +       }
>>>> +
>>>> +       clk = of_clk_get(np, 0);
>>>> +       if (!IS_ERR(clk)) {
>>>> +               ret = clk_prepare_enable(clk);
>>>> +               if (ret) {
>>>> +                       clk_put(clk);
>>>> +                       goto out_unmap;
>>>> +               }
>>>> +
>>>> +               rate = clk_get_rate(clk);
>>>> +       }
>>>> +
>>>> +       /* If no clock found, try to get clock-frequency property */
>>>> +       if (!rate) {
>>>> +               ret = of_property_read_u32(np, "clock-frequency",
>>>> &rate);
>>>> +               if (ret)
>>>> +                       goto out_unmap;
>>>
>>>
>>>
>>> Shouldn't be 'goto out_clk_disable' ?
>>
>>
>> No, because I assumed !rate means we failed to get the clock.
>> Actually, clk_get_rate could return 0, so relying on rate value is not
>> safe.
>>
>> I propose to get clock-frequency property if IS_ERR(clk).
>>
>> Is it fine for you?
>
>
> Why not invert the conditions ? If the 'clock-frequency' is specified in the
> DT then it overrides the clk_get_rate(). So the resulting code will be:
>
> ret = of_property_read_u32(np, "clock-frequency", &rate);
> if (ret) {
>         clk = of_clk_get(np, 0);
>         if (IS_ERR(clk))
>                 goto out_unmap;
>
>         ret = clk_prepare_enable(clk);
>         if (ret)
>                 goto out_clk_put;
>
>         rate = clk_get_rate(clk);
>         if (!rate)
>                 goto out_clk_unprepare;
>
> }

Ok, it looks sensible.
I will do this in next version.

>
>
>
>>>> +       }
>>>> +
>>>> +       writel_relaxed(SYSTICK_LOAD_RELOAD_MASK, base + SYST_RVR);
>>>> +       writel_relaxed(SYST_CSR_ENABLE, base + SYST_CSR);
>>>> +
>>>> +       ret = clocksource_mmio_init(base + SYST_CVR, "arm_system_timer",
>>>> rate,
>>>> +                       200, 24, clocksource_mmio_readl_down);
>>>> +       if (ret) {
>>>> +               pr_err("failed to init clocksource (%d)\n", ret);
>>>> +               goto out_clk_disable;
>>>> +       }
>>>> +
>>>> +       pr_info("ARM System timer initialized as clocksource\n");
>>>> +
>>>> +       return;
>>>> +
>>>> +out_clk_disable:
>>>> +       if (!IS_ERR(clk))
>>>
>>>
>>>
>>> Why do you need this check ?
>>
>>
>> To handle the case were no clock was found, but a clk-frequency value
>> was provided.
>>
>>>
>>> It isn't missing a clk_put ?
>>
>>
>> Right, thanks for spotting this.
>>
>> I wonder if it makes sense to implement the error path.
>> If we fail to initialize the clocksource, the system will be unusable.
>>
>> Maybe I should just perform a BUG_ON() in the error cases, as most of
>> the other clocksource drivers do.
>> What is your view?
>
>
> I prefer to not BUG_ON in the init functions because it already happen that
> drivers were bugging at init time and when a driver was reused on another
> platform with several timers available, the board was not able to boot
> because one timer was not used, hence not defined in the DT. I don't know if
> that could be the case for this platform but I prefer to keep thing going
> smoothly and return from init even if that lead to a kernel hang. Of course,
> the errors must be displayed (pr_warn, pr_err, pr_notice, etc ...).

Ok, let's keep the error path, that's much cleaner indeed.

>
>>>
>>>> +               clk_disable_unprepare(clk);
>>>> +out_unmap:
>>>> +       iounmap(base);
>>>> +       WARN(ret, "ARM System timer register failed (%d)\n", ret);
>
>
> pr_warn

Sure, will fix.

Thanks,
Maxime

>
> Thanks
>
>   -- Daniel
>
>
> --
>  <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>
> Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
> <http://twitter.com/#!/linaroorg> Twitter |
> <http://www.linaro.org/linaro-blog/> Blog
>
--
To unsubscribe from this list: send the line "unsubscribe linux-arch" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Kernel]     [Kernel Newbies]     [x86 Platform Driver]     [Netdev]     [Linux Wireless]     [Netfilter]     [Bugtraq]     [Linux Filesystems]     [Yosemite Discussion]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Device Mapper]

  Powered by Linux