Extend the bq24257 charger's device tree documentation to cover the
bq24250 and bq24251 devices as well feature additions.
Signed-off-by: Andreas Dannenberg <dannenberg@xxxxxx>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
---
.../devicetree/bindings/power/bq24257.txt | 53 ++++++++++++++++++++--
1 file changed, 48 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/bq24257.txt
index 5c9d394..d693702 100644
--- a/Documentation/devicetree/bindings/power/bq24257.txt
+++ b/Documentation/devicetree/bindings/power/bq24257.txt
@@ -1,21 +1,64 @@
-Binding for TI bq24257 Li-Ion Charger
+Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
Required properties:
- compatible: Should contain one of the following:
+ * "ti,bq24250"
+ * "ti,bq24251"
* "ti,bq24257"
-- reg: integer, i2c address of the device.
+- reg: integer, i2c address of the device.
+- interrupt-parent: Should be the phandle for the interrupt controller. Use in
+ conjunction with "interrupts".
+- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
+ conjunction with "interrupt-parent".
- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
-- ti,charge-current: integer, maximum charging current in uA.
-- ti,termination-current: integer, charge will be terminated when current in
- constant-voltage phase drops below this value (in uA).
+- ti,charge-current: integer, maximum charging current in uA.
+- ti,termination-current: integer, charge will be terminated when current in
+ constant-voltage phase drops below this value (in uA).
+
+Optional properties:
+- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
+ This pin is not available on all devices however it should be used if
+ possible as this is the recommended way to obtain the charger's input PG
+ state. If this pin is not specified a software-based approach for PG
+ detection is used.
+- ti,current-limit: The maximum current to be drawn from the charger's input
+ (in uA). If this property is not specified, the input limit current is
+ set automatically using USB D+/D- signal based charger type detection.
+ If the hardware does not support the D+/D- based detection, a default
+ of 500,000 is used (=500mA) instead.
+- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
+ not specified a default of 6,5000,000 (=6.5V) is used.
+- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
+ power path management (in uV). If not specified a default of 4,360,000
+ (=4.36V) is used.
Example:
bq24257 {
compatible = "ti,bq24257";
reg = <0x6a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+ pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
ti,battery-regulation-voltage = <4200000>;
ti,charge-current = <1000000>;
ti,termination-current = <50000>;
};
+
+Example:
+
+bq24250 {
+ compatible = "ti,bq24250";
+ reg = <0x6a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <500000>;
+ ti,termination-current = <50000>;
+ ti,current-limit = <900000>;
+ ti,ovp-voltage = <9500000>;
+ ti,in-dpm-voltage = <4440000>;
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-api" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
