Hi, I think this regression is not yet solved. I encounter this or a similar problem with an PC Engines APU.1C device (see: http://pcengines.ch/apu.htm). It has 3 network interfaces each requiring the r8169 kernel module. With 4.0.0-rc4 I get this error message at boot (for each of the 3 devices): [ 3.562301] r8169 0000:01:00.0 (unnamed net_device) (uninitialized): rtl_chipcmd_cond == 1 (loop: 100, delay: 100). "ifconfig -a" shows ff:ff:ff:ff:ff:ff as MAC address for each of the interfaces (see eth0 as example): eth0 Link encap:Ethernet HWaddr ff:ff:ff:ff:ff:ff BROADCAST PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) The network interfaces cannot be brought up/used. The same device and setup did work with a previously used 3.18.0-rc5 kernel. When I boot it with this 3.18.0-rc5 kernel everything i OK, interfaces come up and work. Please find attached: -> dmesg output when starting device with kernel 4.0.0-rc4 -> dmesg output when starting device with kernel 3.18.0-rc5 -> lspci of the device I am happy to assist with testing and try to provide any information needed. Regards, Bernhard
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.18.0-rc5-ecknn+ (root@kali) (gcc version 4.7.2 (Debian 4.7.2-5) ) #2 SMP Sat Nov 29 17:41:14 CET 2014 [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.18.0-rc5-ecknn+ root=UUID=0a8a0627-f77c-4195-b43b-e6f6d879a3b1 ro console=ttyS0,115200n8 console=ttyS0,115200n8 quiet [ 0.000000] tseg: 0000000000 [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007e16ebff] usable [ 0.000000] BIOS-e820: [mem 0x000000007e16ec00-0x000000007efffbff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000f8ffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.7 present. [ 0.000000] DMI: PC Engines APU, BIOS unknown 12/24/2013 [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] AGP: No AGP bridge found [ 0.000000] e820: last_pfn = 0x7e16e max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-FFFFF write-back [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 07F000000 mask FFF000000 uncachable [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 base 0FFE00000 mask FFFE00000 write-protect [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] found SMP MP-table at [mem 0x000fda10-0x000fda1f] mapped at [ffff8800000fda10] [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576 [ 0.000000] Using GB pages for direct mapping [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] BRK [0x01a99000, 0x01a99fff] PGTABLE [ 0.000000] BRK [0x01a9a000, 0x01a9afff] PGTABLE [ 0.000000] BRK [0x01a9b000, 0x01a9bfff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x7de00000-0x7dffffff] [ 0.000000] [mem 0x7de00000-0x7dffffff] page 2M [ 0.000000] BRK [0x01a9c000, 0x01a9cfff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x7c000000-0x7ddfffff] [ 0.000000] [mem 0x7c000000-0x7ddfffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x00100000-0x7bffffff] [ 0.000000] [mem 0x00100000-0x001fffff] page 4k [ 0.000000] [mem 0x00200000-0x7bffffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x7e000000-0x7e16dfff] [ 0.000000] [mem 0x7e000000-0x7e16dfff] page 4k [ 0.000000] BRK [0x01a9d000, 0x01a9dfff] PGTABLE [ 0.000000] RAMDISK: [mem 0x362dc000-0x37165fff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000FD9F0 000014 (v00 CORE ) [ 0.000000] ACPI: RSDT 0x000000007E171024 000040 (v01 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: FACP 0x000000007E173A20 0000F4 (v04 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: DSDT 0x000000007E1710C8 002915 (v02 PCENG APU 00010001 INTL 20121114) [ 0.000000] ACPI: FACS 0x000000007E1739E0 000040 [ 0.000000] ACPI: HPET 0x000000007E173B18 000038 (v01 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: APIC 0x000000007E173B50 00005C (v01 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: HEST 0x000000007E173BB0 000198 (v01 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: SSDT 0x000000007E173D50 00168E (v02 AMD ALIB 00000001 MSFT 04000000) [ 0.000000] ACPI: SSDT 0x000000007E1753E0 00030C (v01 AMD POWERNOW 00000001 AMD 00000001) [ 0.000000] ACPI: SSDT 0x000000007E1756F0 000045 (v02 CORE COREBOOT 0000002A CORE 0000002A) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000007e16dfff] [ 0.000000] NODE_DATA(0) allocated [mem 0x7e16a000-0x7e16dfff] [ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff88007b800000-ffff88007d3fffff] on node 0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x0009efff] [ 0.000000] node 0: [mem 0x00100000-0x7e16dfff] [ 0.000000] Initmem setup node 0 [mem 0x00001000-0x7e16dfff] [ 0.000000] On node 0 totalpages: 516364 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 21 pages reserved [ 0.000000] DMA zone: 3998 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 7006 pages used for memmap [ 0.000000] DMA32 zone: 512366 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x43538210 base: 0xfed00000 [ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] e820: [mem 0x7efffc00-0xf7ffffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff88007de00000 s86016 r8192 d28672 u1048576 [ 0.000000] pcpu-alloc: s86016 r8192 d28672 u1048576 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 509281 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.18.0-rc5-ecknn+ root=UUID=0a8a0627-f77c-4195-b43b-e6f6d879a3b1 ro console=ttyS0,115200n8 console=ttyS0,115200n8 quiet [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] AGP: Checking aperture... [ 0.000000] AGP: No AGP bridge found [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] Memory: 2010428K/2065456K available (5230K kernel code, 765K rwdata, 1728K rodata, 1020K init, 840K bss, 55028K reserved) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:33024 nr_irqs:440 0 [ 0.000000] spurious 8259A interrupt: IRQ7. [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled [ 0.000000] allocated 8388608 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 1000.094 MHz processor [ 0.000077] Calibrating delay loop (skipped), value calculated using timer frequency.. 2000.18 BogoMIPS (lpj=4000376) [ 0.000086] pid_max: default: 32768 minimum: 301 [ 0.000115] ACPI: Core revision 20140926 [ 0.008581] ACPI: All ACPI Tables successfully acquired [ 0.008684] Security Framework initialized [ 0.008697] AppArmor: AppArmor disabled by boot time parameter [ 0.008701] Yama: becoming mindful. [ 0.009157] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.011167] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.012175] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.012193] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.012864] Initializing cgroup subsys memory [ 0.012892] Initializing cgroup subsys devices [ 0.012905] Initializing cgroup subsys freezer [ 0.012914] Initializing cgroup subsys net_cls [ 0.012923] Initializing cgroup subsys blkio [ 0.012934] Initializing cgroup subsys perf_event [ 0.013002] CPU: Physical Processor ID: 0 [ 0.013006] CPU: Processor Core ID: 0 [ 0.013011] mce: CPU supports 6 MCE banks [ 0.013035] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4 [ 0.013035] Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4, 1GB 0 [ 0.013318] Freeing SMP alternatives memory: 20K (ffffffff819c0000 - ffffffff819c5000) [ 0.017370] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0 [ 0.057075] smpboot: CPU0: AMD G-T40E Processor (fam: 14, model: 02, stepping: 00) [ 0.161929] Performance Events: AMD PMU driver. [ 0.161942] ... version: 0 [ 0.161947] ... bit width: 48 [ 0.161950] ... generic registers: 4 [ 0.161954] ... value mask: 0000ffffffffffff [ 0.161958] ... max period: 00007fffffffffff [ 0.161961] ... fixed-purpose events: 0 [ 0.161965] ... event mask: 000000000000000f [ 0.162864] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.163183] x86: Booting SMP configuration: [ 0.163190] .... node #0, CPUs: #1 [ 0.176378] x86: Booted up 1 node, 2 CPUs [ 0.176386] smpboot: Total of 2 processors activated (4000.37 BogoMIPS) [ 0.177727] devtmpfs: initialized [ 0.191773] pinctrl core: initialized pinctrl subsystem [ 0.192246] NET: Registered protocol family 16 [ 0.204678] cpuidle: using governor ladder [ 0.214164] cpuidle: using governor menu [ 0.214559] ACPI: bus type PCI registered [ 0.214567] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.214922] PCI: Using configuration type 1 for base access [ 0.214927] PCI: Using configuration type 1 for extended access [ 0.230874] ACPI: Added _OSI(Module Device) [ 0.230885] ACPI: Added _OSI(Processor Device) [ 0.230890] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.230895] ACPI: Added _OSI(Processor Aggregator Device) [ 0.234219] ACPI: Executed 2 blocks of module-level executable AML code [ 0.241654] ACPI: Interpreter enabled [ 0.241721] ACPI: (supports S0 S1 S2 S3 S4 S5) [ 0.241727] ACPI: Using IOAPIC for interrupt routing [ 0.241779] HEST: Table parsing has been initialized. [ 0.241788] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.263268] acpi LNXCPU:01: Invalid PBLK length [0] [ 0.268517] ACPI: PCI Interrupt Link [INTA] (IRQs 3 4 5 7 10 11 12 15) *0, disabled. [ 0.268783] ACPI: PCI Interrupt Link [INTB] (IRQs 3 4 5 7 10 11 12 15) *0, disabled. [ 0.269041] ACPI: PCI Interrupt Link [INTC] (IRQs 3 4 5 7 10 11 12 15) *0, disabled. [ 0.269297] ACPI: PCI Interrupt Link [INTD] (IRQs 3 4 5 7 10 11 12 15) *0, disabled. [ 0.269551] ACPI: PCI Interrupt Link [INTE] (IRQs 3 4 5 7 10 11 12 15) *0, disabled. [ 0.269806] ACPI: PCI Interrupt Link [INTF] (IRQs 9) *0, disabled. [ 0.270054] ACPI: PCI Interrupt Link [INTG] (IRQs 3 4 5 7 10 11 12 15) *0, disabled. [ 0.270307] ACPI: PCI Interrupt Link [INTH] (IRQs 3 4 5 7 10 11 12 15) *0, disabled. [ 0.270527] acpi PNP0A03:00: [Firmware Bug]: no secondary bus range in _CRS [ 0.270553] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.270569] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI] [ 0.270805] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability] [ 0.271744] PCI host bridge to bus 0000:00 [ 0.271754] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.271762] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7] [ 0.271769] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff] [ 0.271776] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff] [ 0.271783] pci_bus 0000:00: root bus resource [mem 0x7f000000-0xffffffff] [ 0.271805] pci 0000:00:00.0: [1022:1510] type 00 class 0x060000 [ 0.272164] pci 0000:00:04.0: [1022:1512] type 01 class 0x060400 [ 0.272282] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold [ 0.272442] pci 0000:00:04.0: System wakeup disabled by ACPI [ 0.272578] pci 0000:00:05.0: [1022:1513] type 01 class 0x060400 [ 0.272691] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold [ 0.272840] pci 0000:00:05.0: System wakeup disabled by ACPI [ 0.272973] pci 0000:00:06.0: [1022:1514] type 01 class 0x060400 [ 0.273086] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold [ 0.273230] pci 0000:00:06.0: System wakeup disabled by ACPI [ 0.273430] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601 [ 0.273465] pci 0000:00:11.0: reg 0x10: [io 0x4020-0x4027] [ 0.273483] pci 0000:00:11.0: reg 0x14: [io 0x4040-0x4043] [ 0.273501] pci 0000:00:11.0: reg 0x18: [io 0x4028-0x402f] [ 0.273519] pci 0000:00:11.0: reg 0x1c: [io 0x4044-0x4047] [ 0.273537] pci 0000:00:11.0: reg 0x20: [io 0x4000-0x400f] [ 0.273555] pci 0000:00:11.0: reg 0x24: [mem 0xfeb04000-0xfeb043ff] [ 0.273910] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 [ 0.273937] pci 0000:00:12.0: reg 0x10: [mem 0xfeb00000-0xfeb00fff] [ 0.274159] pci 0000:00:12.0: System wakeup disabled by ACPI [ 0.274345] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 [ 0.274379] pci 0000:00:12.2: reg 0x10: [mem 0xfeb04400-0xfeb044ff] [ 0.274516] pci 0000:00:12.2: supports D1 D2 [ 0.274522] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.274662] pci 0000:00:12.2: System wakeup disabled by ACPI [ 0.274845] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 [ 0.274870] pci 0000:00:13.0: reg 0x10: [mem 0xfeb01000-0xfeb01fff] [ 0.275092] pci 0000:00:13.0: System wakeup disabled by ACPI [ 0.275276] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 [ 0.275310] pci 0000:00:13.2: reg 0x10: [mem 0xfeb04500-0xfeb045ff] [ 0.275446] pci 0000:00:13.2: supports D1 D2 [ 0.275452] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.275599] pci 0000:00:13.2: System wakeup disabled by ACPI [ 0.275784] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 [ 0.276162] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a [ 0.276188] pci 0000:00:14.1: reg 0x10: [io 0x4030-0x4037] [ 0.276206] pci 0000:00:14.1: reg 0x14: [io 0x4048-0x404b] [ 0.276224] pci 0000:00:14.1: reg 0x18: [io 0x4038-0x403f] [ 0.276241] pci 0000:00:14.1: reg 0x1c: [io 0x404c-0x404f] [ 0.276259] pci 0000:00:14.1: reg 0x20: [io 0x4010-0x401f] [ 0.276293] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.276299] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.276305] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.276310] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.276615] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 [ 0.276995] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 [ 0.277193] pci 0000:00:14.4: System wakeup disabled by ACPI [ 0.277372] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 [ 0.277397] pci 0000:00:14.5: reg 0x10: [mem 0xfeb02000-0xfeb02fff] [ 0.277621] pci 0000:00:14.5: System wakeup disabled by ACPI [ 0.277812] pci 0000:00:15.0: [1002:43a0] type 01 class 0x060400 [ 0.277954] pci 0000:00:15.0: supports D1 D2 [ 0.278101] pci 0000:00:15.0: System wakeup disabled by ACPI [ 0.278276] pci 0000:00:16.0: [1002:4397] type 00 class 0x0c0310 [ 0.278302] pci 0000:00:16.0: reg 0x10: [mem 0xfeb03000-0xfeb03fff] [ 0.278522] pci 0000:00:16.0: System wakeup disabled by ACPI [ 0.278709] pci 0000:00:16.2: [1002:4396] type 00 class 0x0c0320 [ 0.278742] pci 0000:00:16.2: reg 0x10: [mem 0xfeb04600-0xfeb046ff] [ 0.278879] pci 0000:00:16.2: supports D1 D2 [ 0.278885] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot [ 0.279029] pci 0000:00:16.2: System wakeup disabled by ACPI [ 0.279217] pci 0000:00:18.0: [1022:1700] type 00 class 0x060000 [ 0.279491] pci 0000:00:18.1: [1022:1701] type 00 class 0x060000 [ 0.279758] pci 0000:00:18.2: [1022:1702] type 00 class 0x060000 [ 0.280026] pci 0000:00:18.3: [1022:1703] type 00 class 0x060000 [ 0.280311] pci 0000:00:18.4: [1022:1704] type 00 class 0x060000 [ 0.280589] pci 0000:00:18.5: [1022:1718] type 00 class 0x060000 [ 0.280853] pci 0000:00:18.6: [1022:1716] type 00 class 0x060000 [ 0.281116] pci 0000:00:18.7: [1022:1719] type 00 class 0x060000 [ 0.281586] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 0.281615] pci 0000:01:00.0: reg 0x10: [io 0x1000-0x10ff] [ 0.281653] pci 0000:01:00.0: reg 0x18: [mem 0xfe600000-0xfe600fff 64bit] [ 0.281678] pci 0000:01:00.0: reg 0x20: [mem 0xfe500000-0xfe503fff 64bit pref] [ 0.281807] pci 0000:01:00.0: supports D1 D2 [ 0.281813] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.292657] pci 0000:00:04.0: PCI bridge to [bus 01] [ 0.292681] pci 0000:00:04.0: bridge window [io 0x1000-0x1fff] [ 0.292691] pci 0000:00:04.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 0.292703] pci 0000:00:04.0: bridge window [mem 0xfe500000-0xfe5fffff 64bit pref] [ 0.292913] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 0.292947] pci 0000:02:00.0: reg 0x10: [io 0x2000-0x20ff] [ 0.292985] pci 0000:02:00.0: reg 0x18: [mem 0xfe800000-0xfe800fff 64bit] [ 0.293011] pci 0000:02:00.0: reg 0x20: [mem 0xfe700000-0xfe703fff 64bit pref] [ 0.293158] pci 0000:02:00.0: supports D1 D2 [ 0.293165] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.300657] pci 0000:00:05.0: PCI bridge to [bus 02] [ 0.300681] pci 0000:00:05.0: bridge window [io 0x2000-0x2fff] [ 0.300691] pci 0000:00:05.0: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.300703] pci 0000:00:05.0: bridge window [mem 0xfe700000-0xfe7fffff 64bit pref] [ 0.300925] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000 [ 0.300959] pci 0000:03:00.0: reg 0x10: [io 0x3000-0x30ff] [ 0.300997] pci 0000:03:00.0: reg 0x18: [mem 0xfea00000-0xfea00fff 64bit] [ 0.301023] pci 0000:03:00.0: reg 0x20: [mem 0xfe900000-0xfe903fff 64bit pref] [ 0.301169] pci 0000:03:00.0: supports D1 D2 [ 0.301176] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.308657] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.308680] pci 0000:00:06.0: bridge window [io 0x3000-0x3fff] [ 0.308690] pci 0000:00:06.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.308703] pci 0000:00:06.0: bridge window [mem 0xfe900000-0xfe9fffff 64bit pref] [ 0.308766] pci 0000:00:14.4: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.309034] pci 0000:00:15.0: PCI bridge to [bus 04] [ 0.309283] pci 0000:00:14.4: PCI bridge to [bus 05-ff] (subtractive decode) [ 0.309298] pci 0000:00:14.4: bridge window [mem 0x00000000-0x000fffff] [ 0.309308] pci 0000:00:14.4: bridge window [mem 0x00000000-0x000fffff pref] [ 0.309316] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 0.309323] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 0.309330] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 0.309336] pci 0000:00:14.4: bridge window [mem 0x7f000000-0xffffffff] (subtractive decode) [ 0.309345] pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 05 [ 0.310574] ACPI: Enabled 6 GPEs in block 00 to 1F [ 0.311197] vgaarb: loaded [ 0.311659] PCI: Using ACPI for IRQ routing [ 0.311675] PCI: pci_cache_line_size set to 64 bytes [ 0.311851] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff] [ 0.311859] e820: reserve RAM buffer [mem 0x7e16ec00-0x7fffffff] [ 0.312386] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.312399] hpet0: 3 comparators, 32-bit 14.318180 MHz counter [ 0.314640] Switched to clocksource hpet [ 0.321635] pnp: PnP ACPI init [ 0.322628] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.322784] pnp: PnP ACPI: found 1 devices [ 0.341831] pci 0000:00:04.0: PCI bridge to [bus 01] [ 0.341848] pci 0000:00:04.0: bridge window [io 0x1000-0x1fff] [ 0.341860] pci 0000:00:04.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 0.341870] pci 0000:00:04.0: bridge window [mem 0xfe500000-0xfe5fffff 64bit pref] [ 0.341881] pci 0000:00:05.0: PCI bridge to [bus 02] [ 0.341889] pci 0000:00:05.0: bridge window [io 0x2000-0x2fff] [ 0.341899] pci 0000:00:05.0: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.341908] pci 0000:00:05.0: bridge window [mem 0xfe700000-0xfe7fffff 64bit pref] [ 0.341918] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.341925] pci 0000:00:06.0: bridge window [io 0x3000-0x3fff] [ 0.341935] pci 0000:00:06.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.341943] pci 0000:00:06.0: bridge window [mem 0xfe900000-0xfe9fffff 64bit pref] [ 0.341954] pci 0000:00:14.4: PCI bridge to [bus 05] [ 0.342021] pci 0000:00:15.0: PCI bridge to [bus 04] [ 0.342044] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.342050] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.342056] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.342063] pci_bus 0000:00: resource 7 [mem 0x7f000000-0xffffffff] [ 0.342069] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] [ 0.342076] pci_bus 0000:01: resource 1 [mem 0xfe600000-0xfe6fffff] [ 0.342082] pci_bus 0000:01: resource 2 [mem 0xfe500000-0xfe5fffff 64bit pref] [ 0.342089] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff] [ 0.342095] pci_bus 0000:02: resource 1 [mem 0xfe800000-0xfe8fffff] [ 0.342102] pci_bus 0000:02: resource 2 [mem 0xfe700000-0xfe7fffff 64bit pref] [ 0.342108] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff] [ 0.342114] pci_bus 0000:03: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.342121] pci_bus 0000:03: resource 2 [mem 0xfe900000-0xfe9fffff 64bit pref] [ 0.342128] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7] [ 0.342134] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff] [ 0.342139] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff] [ 0.342145] pci_bus 0000:05: resource 7 [mem 0x7f000000-0xffffffff] [ 0.342340] NET: Registered protocol family 2 [ 0.342975] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.343184] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 0.343362] TCP: Hash tables configured (established 16384 bind 16384) [ 0.343477] TCP: reno registered [ 0.343497] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 0.343534] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 0.343858] NET: Registered protocol family 1 [ 0.348156] PCI: CLS 64 bytes, default 64 [ 0.348316] Unpacking initramfs... [ 1.224861] Freeing initrd memory: 14888K (ffff8800362dc000 - ffff880037166000) [ 1.225788] microcode: CPU0: patch_level=0x05000101 [ 1.225816] microcode: CPU1: patch_level=0x05000101 [ 1.226220] microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba [ 1.226247] LVT offset 0 assigned for vector 0x400 [ 1.226371] perf: AMD IBS detected (0x000000ff) [ 1.227466] futex hash table entries: 512 (order: 3, 32768 bytes) [ 1.227597] audit: initializing netlink subsys (disabled) [ 1.227651] audit: type=2000 audit(1426720387.124:1): initialized [ 1.228722] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.229569] VFS: Disk quotas dquot_6.5.2 [ 1.229685] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.229927] msgmni has been set to 3955 [ 1.231900] alg: No test for stdrng (krng) [ 1.232080] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.232243] io scheduler noop registered [ 1.232253] io scheduler deadline registered [ 1.232289] io scheduler cfq registered (default) [ 1.232947] pcieport 0000:00:04.0: irq 24 for MSI/MSI-X [ 1.233367] pcieport 0000:00:05.0: irq 25 for MSI/MSI-X [ 1.233760] pcieport 0000:00:06.0: irq 26 for MSI/MSI-X [ 1.234249] pcieport 0000:00:15.0: irq 27 for MSI/MSI-X [ 1.234545] pcieport 0000:00:04.0: Signaling PME through PCIe PME interrupt [ 1.234553] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.234563] pcie_pme 0000:00:04.0:pcie01: service driver pcie_pme loaded [ 1.234608] pcieport 0000:00:05.0: Signaling PME through PCIe PME interrupt [ 1.234615] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 1.234624] pcie_pme 0000:00:05.0:pcie01: service driver pcie_pme loaded [ 1.234764] pcieport 0000:00:06.0: Signaling PME through PCIe PME interrupt [ 1.234771] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt [ 1.234780] pcie_pme 0000:00:06.0:pcie01: service driver pcie_pme loaded [ 1.234874] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt [ 1.234885] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded [ 1.234945] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.235003] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 1.235296] GHES: Failed to enable APEI firmware first mode. [ 1.235754] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.256510] platform serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 1.277429] platform serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.279179] Linux agpgart interface v0.103 [ 1.279537] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 2.222762] tsc: Refined TSC clocksource calibration: 999.999 MHz [ 3.186350] i8042: No controller found [ 3.190725] mousedev: PS/2 mouse device common for all mice [ 3.190873] rtc_cmos 00:00: RTC can wake from S4 [ 3.191382] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0 [ 3.191492] rtc_cmos 00:00: alarms up to one day, 114 bytes nvram, hpet irqs [ 3.191559] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@xxxxxxx> [ 3.191563] AMD IOMMUv2 functionality not available on this system [ 3.191865] TCP: cubic registered [ 3.192043] NET: Registered protocol family 10 [ 3.192849] mip6: Mobile IPv6 [ 3.192862] NET: Registered protocol family 17 [ 3.192881] mpls_gso: MPLS GSO support [ 3.194404] registered taskstats version 1 [ 3.195813] rtc_cmos 00:00: setting system clock to 2015-03-18 23:13:09 UTC (1426720389) [ 3.195994] PM: Hibernation image not present or could not be loaded. [ 3.199265] Freeing unused kernel memory: 1020K (ffffffff818c1000 - ffffffff819c0000) [ 3.199278] Write protecting the kernel read-only data: 8192k [ 3.207069] Freeing unused kernel memory: 904K (ffff88000151e000 - ffff880001600000) [ 3.209719] Freeing unused kernel memory: 320K (ffff8800017b0000 - ffff880001800000) [ 3.222989] Switched to clocksource tsc [ 3.454462] udevd[64]: starting version 175 [ 3.512851] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.513260] r8169 0000:01:00.0: irq 28 for MSI/MSI-X [ 3.513764] r8169 0000:01:00.0 eth0: RTL8168e/8111e at 0xffffc90000002000, 00:0d:b9:33:09:88, XID 0c200000 IRQ 28 [ 3.513774] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.558350] ACPI: bus type USB registered [ 3.558450] usbcore: registered new interface driver usbfs [ 3.558492] usbcore: registered new interface driver hub [ 3.560978] SCSI subsystem initialized [ 3.567251] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.567688] r8169 0000:02:00.0: irq 29 for MSI/MSI-X [ 3.568252] r8169 0000:02:00.0 eth1: RTL8168e/8111e at 0xffffc90000324000, 00:0d:b9:33:09:89, XID 0c200000 IRQ 29 [ 3.568261] r8169 0000:02:00.0 eth1: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.568311] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.568593] r8169 0000:03:00.0: irq 30 for MSI/MSI-X [ 3.569012] r8169 0000:03:00.0 eth2: RTL8168e/8111e at 0xffffc900003a6000, 00:0d:b9:33:09:8a, XID 0c200000 IRQ 30 [ 3.569021] r8169 0000:03:00.0 eth2: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 3.581041] usbcore: registered new device driver usb [ 3.582374] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.582992] ehci-pci: EHCI PCI platform driver [ 3.583499] QUIRK: Enable AMD PLL fix [ 3.583609] ehci-pci 0000:00:12.2: EHCI Host Controller [ 3.583635] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 1 [ 3.583653] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 3.583721] ehci-pci 0000:00:12.2: debug port 1 [ 3.583816] ehci-pci 0000:00:12.2: irq 17, io mem 0xfeb04400 [ 3.585179] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.585669] ohci-pci: OHCI PCI platform driver [ 3.594797] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 3.594947] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.594955] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.594962] usb usb1: Product: EHCI Host Controller [ 3.594968] usb usb1: Manufacturer: Linux 3.18.0-rc5-ecknn+ ehci_hcd [ 3.594975] usb usb1: SerialNumber: 0000:00:12.2 [ 3.595462] hub 1-0:1.0: USB hub found [ 3.595490] hub 1-0:1.0: 5 ports detected [ 3.596524] ehci-pci 0000:00:13.2: EHCI Host Controller [ 3.596546] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 2 [ 3.596564] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 3.596632] ehci-pci 0000:00:13.2: debug port 1 [ 3.596698] ehci-pci 0000:00:13.2: irq 17, io mem 0xfeb04500 [ 3.606767] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 3.606902] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.606911] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.606917] usb usb2: Product: EHCI Host Controller [ 3.606923] usb usb2: Manufacturer: Linux 3.18.0-rc5-ecknn+ ehci_hcd [ 3.606929] usb usb2: SerialNumber: 0000:00:13.2 [ 3.607452] hub 2-0:1.0: USB hub found [ 3.607489] hub 2-0:1.0: 5 ports detected [ 3.608482] ehci-pci 0000:00:16.2: EHCI Host Controller [ 3.608504] ehci-pci 0000:00:16.2: new USB bus registered, assigned bus number 3 [ 3.608522] ehci-pci 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 3.608590] ehci-pci 0000:00:16.2: debug port 1 [ 3.608661] ehci-pci 0000:00:16.2: irq 17, io mem 0xfeb04600 [ 3.608790] libata version 3.00 loaded. [ 3.618954] ehci-pci 0000:00:16.2: USB 2.0 started, EHCI 1.00 [ 3.619121] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.619130] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.619138] usb usb3: Product: EHCI Host Controller [ 3.619144] usb usb3: Manufacturer: Linux 3.18.0-rc5-ecknn+ ehci_hcd [ 3.619151] usb usb3: SerialNumber: 0000:00:16.2 [ 3.619554] hub 3-0:1.0: USB hub found [ 3.619586] hub 3-0:1.0: 4 ports detected [ 3.620539] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 3.620565] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 4 [ 3.620764] ohci-pci 0000:00:12.0: irq 18, io mem 0xfeb00000 [ 3.679415] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.679429] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.679436] usb usb4: Product: OHCI PCI host controller [ 3.679443] usb usb4: Manufacturer: Linux 3.18.0-rc5-ecknn+ ohci_hcd [ 3.679449] usb usb4: SerialNumber: 0000:00:12.0 [ 3.680155] hub 4-0:1.0: USB hub found [ 3.680233] hub 4-0:1.0: 5 ports detected [ 3.681213] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 3.681235] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 3.681356] ohci-pci 0000:00:13.0: irq 18, io mem 0xfeb01000 [ 3.738957] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.738971] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.738978] usb usb5: Product: OHCI PCI host controller [ 3.738984] usb usb5: Manufacturer: Linux 3.18.0-rc5-ecknn+ ohci_hcd [ 3.738990] usb usb5: SerialNumber: 0000:00:13.0 [ 3.739663] hub 5-0:1.0: USB hub found [ 3.739746] hub 5-0:1.0: 5 ports detected [ 3.740692] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 3.740713] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 6 [ 3.740837] ohci-pci 0000:00:14.5: irq 18, io mem 0xfeb02000 [ 3.799124] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.799138] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.799146] usb usb6: Product: OHCI PCI host controller [ 3.799152] usb usb6: Manufacturer: Linux 3.18.0-rc5-ecknn+ ohci_hcd [ 3.799158] usb usb6: SerialNumber: 0000:00:14.5 [ 3.799838] hub 6-0:1.0: USB hub found [ 3.799880] hub 6-0:1.0: 2 ports detected [ 3.800698] ohci-pci 0000:00:16.0: OHCI PCI host controller [ 3.800723] ohci-pci 0000:00:16.0: new USB bus registered, assigned bus number 7 [ 3.800839] ohci-pci 0000:00:16.0: irq 18, io mem 0xfeb03000 [ 3.859094] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.859108] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.859115] usb usb7: Product: OHCI PCI host controller [ 3.859122] usb usb7: Manufacturer: Linux 3.18.0-rc5-ecknn+ ohci_hcd [ 3.859128] usb usb7: SerialNumber: 0000:00:16.0 [ 3.859827] hub 7-0:1.0: USB hub found [ 3.859911] hub 7-0:1.0: 4 ports detected [ 3.864347] scsi host0: pata_atiixp [ 3.864674] scsi host1: pata_atiixp [ 3.864825] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4010 irq 14 [ 3.864833] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x4018 irq 15 [ 3.864914] ahci 0000:00:11.0: version 3.0 [ 3.865617] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode [ 3.865628] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck led clo pmp pio slum part [ 3.869627] scsi host2: ahci [ 3.869945] scsi host3: ahci [ 3.870203] scsi host4: ahci [ 3.873498] scsi host5: ahci [ 3.873794] ata3: SATA max UDMA/133 abar m1024@0xfeb04000 port 0xfeb04100 irq 19 [ 3.873803] ata4: SATA max UDMA/133 abar m1024@0xfeb04000 port 0xfeb04180 irq 19 [ 3.873811] ata5: SATA max UDMA/133 abar m1024@0xfeb04000 port 0xfeb04200 irq 19 [ 3.873818] ata6: SATA max UDMA/133 abar m1024@0xfeb04000 port 0xfeb04280 irq 19 [ 3.906984] usb 1-2: new high-speed USB device number 2 using ehci-pci [ 3.930926] usb 3-1: new high-speed USB device number 2 using ehci-pci [ 4.066150] usb 3-1: New USB device found, idVendor=058f, idProduct=6366 [ 4.066166] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.066175] usb 3-1: Product: Flash Card Reader/Writer [ 4.066182] usb 3-1: Manufacturer: Generic [ 4.066190] usb 3-1: SerialNumber: 058F63666485 [ 4.074619] usb-storage 3-1:1.0: USB Mass Storage device detected [ 4.075328] scsi host6: usb-storage 3-1:1.0 [ 4.075600] usbcore: registered new interface driver usb-storage [ 4.129494] usb 1-2: New USB device found, idVendor=413c, idProduct=8147 [ 4.129512] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.129519] usb 1-2: Product: Dell Wireless 5530 HSPA Mobile Broadband Minicard Device [ 4.129526] usb 1-2: Manufacturer: Dell [ 4.129531] usb 1-2: SerialNumber: 3558620263894800 [ 4.194804] ata5: SATA link down (SStatus 0 SControl 300) [ 4.194878] ata4: SATA link down (SStatus 0 SControl 300) [ 4.198716] ata6: SATA link down (SStatus 0 SControl 300) [ 4.362945] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 4.378379] ata3.00: ATA-8: KINGSTON SMS200S330G, 524ABBF0, max UDMA/133 [ 4.378392] ata3.00: 58626288 sectors, multi 1: LBA48 NCQ (depth 31/32), AA [ 4.389434] ata3.00: configured for UDMA/133 [ 4.390114] scsi 2:0:0:0: Direct-Access ATA KINGSTON SMS200S BBF0 PQ: 0 ANSI: 5 [ 4.405962] sd 2:0:0:0: [sda] 58626288 512-byte logical blocks: (30.0 GB/27.9 GiB) [ 4.406235] sd 2:0:0:0: [sda] Write Protect is off [ 4.406244] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.406309] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.407464] sda: sda1 sda2 < sda5 > [ 4.409236] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.414501] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.518154] device-mapper: uevent: version 1.0.3 [ 4.518402] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: dm-devel@xxxxxxxxxx [ 4.554220] PM: Starting manual resume from disk [ 4.554235] PM: Hibernation image partition 8:5 present [ 4.554239] PM: Looking for hibernation image. [ 4.554869] PM: Image not found (code -22) [ 4.554880] PM: Hibernation image not present or could not be loaded. [ 4.581868] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 5.076201] scsi 6:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 4 [ 5.077055] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 5.079682] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 5.247164] udevd[381]: starting version 175 [ 5.416864] ACPI: acpi_idle registered with cpuidle [ 5.422612] acpi-cpufreq: overriding BIOS provided _PSD data [ 5.434449] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 5.434468] ACPI: Power Button [PWRB] [ 5.438763] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 5.438781] ACPI: Power Button [PWRF] [ 5.664499] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 [ 5.664629] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20 [ 5.682154] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05 [ 5.682332] sp5100_tco: PCI Revision ID: 0x42 [ 5.682440] sp5100_tco: Using 0xfed80b00 for watchdog MMIO address [ 5.682456] sp5100_tco: Last reboot was not triggered by watchdog. [ 5.683916] sp5100_tco: initialized (0xffffc900003acb00). heartbeat=60 sec (nowayout=0) [ 5.795509] kvm: Nested Virtualization enabled [ 5.795526] kvm: Nested Paging enabled [ 5.831177] cdc_wdm 1-2:1.5: cdc-wdm0: USB WDM device [ 5.837977] cdc_wdm 1-2:1.6: cdc-wdm1: USB WDM device [ 5.839706] usbcore: registered new interface driver cdc_wdm [ 5.847848] cdc_acm 1-2:1.1: ttyACM0: USB ACM device [ 5.855668] cdc_acm 1-2:1.3: ttyACM1: USB ACM device [ 5.859287] cdc_acm 1-2:1.9: ttyACM2: USB ACM device [ 5.861256] usbcore: registered new interface driver cdc_acm [ 5.861266] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 5.878982] cdc_ether 1-2:1.7 wwan0: register 'cdc_ether' at usb-0000:00:12.2-2, Mobile Broadband Network Device, 02:80:37:ec:02:00 [ 5.879070] usbcore: registered new interface driver cdc_ether [ 6.930838] Adding 1239036k swap on /dev/sda5. Priority:-1 extents:1 across:1239036k SS [ 6.985588] EXT4-fs (sda1): re-mounted. Opts: (null) [ 7.105269] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 7.426984] loop: module loaded [ 7.439217] random: vgscan urandom read with 34 bits of entropy available [ 10.262511] r8169 0000:02:00.0 eth1: link down [ 10.262777] r8169 0000:02:00.0 eth1: link down [ 10.265512] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 11.159247] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.189846] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.220361] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 11.227647] Bridge firewalling registered [ 11.263297] device eth0 entered promiscuous mode [ 11.268487] device eth2 entered promiscuous mode [ 11.418374] r8169 0000:01:00.0 eth0: link down [ 11.418461] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 11.562493] r8169 0000:03:00.0 eth2: link down [ 11.562579] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready [ 11.566241] IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready [ 12.605804] r8169 0000:02:00.0 eth1: link up [ 12.605832] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.0.0-rc4 (root@kalipool07) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Wed Mar 18 23:48:21 CET 2015 [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.0.0-rc4 root=UUID=0a8a0627-f77c-4195-b43b-e6f6d879a3b1 ro console=ttyS0,115200n8 console=ttyS0,115200n8 quiet [ 0.000000] tseg: 0000000000 [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007e16ebff] usable [ 0.000000] BIOS-e820: [mem 0x000000007e16ec00-0x000000007efffbff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000f8ffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.7 present. [ 0.000000] DMI: PC Engines APU, BIOS unknown 12/24/2013 [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] AGP: No AGP bridge found [ 0.000000] e820: last_pfn = 0x7e16e max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-FFFFF write-back [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 07F000000 mask FFF000000 uncachable [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 base 0FFE00000 mask FFFE00000 write-protect [ 0.000000] 7 disabled [ 0.000000] PAT configuration [0-7]: WB WC UC- UC WB WC UC- UC [ 0.000000] found SMP MP-table at [mem 0x000fda10-0x000fda1f] mapped at [ffff8800000fda10] [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576 [ 0.000000] Using GB pages for direct mapping [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] BRK [0x01a8a000, 0x01a8afff] PGTABLE [ 0.000000] BRK [0x01a8b000, 0x01a8bfff] PGTABLE [ 0.000000] BRK [0x01a8c000, 0x01a8cfff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x7de00000-0x7dffffff] [ 0.000000] [mem 0x7de00000-0x7dffffff] page 2M [ 0.000000] BRK [0x01a8d000, 0x01a8dfff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x60000000-0x7ddfffff] [ 0.000000] [mem 0x60000000-0x7ddfffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x40000000-0x5fffffff] [ 0.000000] [mem 0x40000000-0x5fffffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x00100000-0x3fffffff] [ 0.000000] [mem 0x00100000-0x001fffff] page 4k [ 0.000000] [mem 0x00200000-0x3fffffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x7e000000-0x7e16dfff] [ 0.000000] [mem 0x7e000000-0x7e16dfff] page 4k [ 0.000000] BRK [0x01a8e000, 0x01a8efff] PGTABLE [ 0.000000] RAMDISK: [mem 0x3631a000-0x37184fff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000FD9F0 000014 (v00 CORE ) [ 0.000000] ACPI: RSDT 0x000000007E171024 000040 (v01 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: FACP 0x000000007E173A20 0000F4 (v04 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: DSDT 0x000000007E1710C8 002915 (v02 PCENG APU 00010001 INTL 20121114) [ 0.000000] ACPI: FACS 0x000000007E1739E0 000040 [ 0.000000] ACPI: HPET 0x000000007E173B18 000038 (v01 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: APIC 0x000000007E173B50 00005C (v01 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: HEST 0x000000007E173BB0 000198 (v01 CORE COREBOOT 00000000 CORE 00000000) [ 0.000000] ACPI: SSDT 0x000000007E173D50 00168E (v02 AMD ALIB 00000001 MSFT 04000000) [ 0.000000] ACPI: SSDT 0x000000007E1753E0 00030C (v01 AMD POWERNOW 00000001 AMD 00000001) [ 0.000000] ACPI: SSDT 0x000000007E1756F0 000045 (v02 CORE COREBOOT 0000002A CORE 0000002A) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000007e16dfff] [ 0.000000] NODE_DATA(0) allocated [mem 0x7e16a000-0x7e16dfff] [ 0.000000] [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007b800000-ffff88007d7fffff] on node 0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x000000007e16dfff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.000000] node 0: [mem 0x0000000000100000-0x000000007e16dfff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000007e16dfff] [ 0.000000] On node 0 totalpages: 516364 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 21 pages reserved [ 0.000000] DMA zone: 3998 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 8006 pages used for memmap [ 0.000000] DMA32 zone: 512366 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x43538210 base: 0xfed00000 [ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] e820: [mem 0x7efffc00-0xf7ffffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 31 pages/cpu @ffff88007de00000 s86040 r8192 d32744 u1048576 [ 0.000000] pcpu-alloc: s86040 r8192 d32744 u1048576 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 508273 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.0.0-rc4 root=UUID=0a8a0627-f77c-4195-b43b-e6f6d879a3b1 ro console=ttyS0,115200n8 console=ttyS0,115200n8 quiet [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] AGP: Checking aperture... [ 0.000000] AGP: No AGP bridge found [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] Memory: 2006508K/2065456K available (5266K kernel code, 740K rwdata, 1760K rodata, 1020K init, 808K bss, 58948K reserved, 0K cma-reserved) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:33024 nr_irqs:440 16 [ 0.000000] spurious 8259A interrupt: IRQ7. [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 1000.039 MHz processor [ 0.000073] Calibrating delay loop (skipped), value calculated using timer frequency.. 2000.07 BogoMIPS (lpj=4000156) [ 0.000082] pid_max: default: 32768 minimum: 301 [ 0.000106] ACPI: Core revision 20150204 [ 0.008589] ACPI: All ACPI Tables successfully acquired [ 0.008689] Security Framework initialized [ 0.008701] AppArmor: AppArmor disabled by boot time parameter [ 0.008705] Yama: becoming mindful. [ 0.009174] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.011321] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.012275] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.012293] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.012987] Initializing cgroup subsys blkio [ 0.013004] Initializing cgroup subsys memory [ 0.013034] Initializing cgroup subsys devices [ 0.013043] Initializing cgroup subsys freezer [ 0.013052] Initializing cgroup subsys net_cls [ 0.013063] Initializing cgroup subsys perf_event [ 0.013129] CPU: Physical Processor ID: 0 [ 0.013133] CPU: Processor Core ID: 0 [ 0.013138] mce: CPU supports 6 MCE banks [ 0.013162] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4 [ 0.013166] Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4, 1GB 0 [ 0.013437] Freeing SMP alternatives memory: 20K (ffffffff819b9000 - ffffffff819be000) [ 0.017455] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0 [ 0.161902] smpboot: CPU0: AMD G-T40E Processor (fam: 14, model: 02, stepping: 00) [ 0.161970] Performance Events: AMD PMU driver. [ 0.161984] ... version: 0 [ 0.161988] ... bit width: 48 [ 0.161992] ... generic registers: 4 [ 0.161996] ... value mask: 0000ffffffffffff [ 0.162000] ... max period: 00007fffffffffff [ 0.162003] ... fixed-purpose events: 0 [ 0.162007] ... event mask: 000000000000000f [ 0.162735] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.163051] x86: Booting SMP configuration: [ 0.163057] .... node #0, CPUs: #1 [ 0.176236] x86: Booted up 1 node, 2 CPUs [ 0.176244] smpboot: Total of 2 processors activated (4000.15 BogoMIPS) [ 0.177475] devtmpfs: initialized [ 0.192959] NET: Registered protocol family 16 [ 0.204538] cpuidle: using governor ladder [ 0.214182] cpuidle: using governor menu [ 0.214565] ACPI: bus type PCI registered [ 0.214573] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.214935] PCI: Using configuration type 1 for base access [ 0.214940] PCI: Using configuration type 1 for extended access [ 0.230492] ACPI: Added _OSI(Module Device) [ 0.230504] ACPI: Added _OSI(Processor Device) [ 0.230509] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.230514] ACPI: Added _OSI(Processor Aggregator Device) [ 0.233872] ACPI: Executed 2 blocks of module-level executable AML code [ 0.241333] ACPI: Interpreter enabled [ 0.241401] ACPI: (supports S0 S1 S2 S3 S4 S5) [ 0.241407] ACPI: Using IOAPIC for interrupt routing [ 0.241463] HEST: Table parsing has been initialized. [ 0.241472] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.252959] acpi LNXCPU:01: Invalid PBLK length [0] [ 0.258233] ACPI: PCI Interrupt Link [INTA] (IRQs 3 4 5 7 10 11 12 15) *0 [ 0.258498] ACPI: PCI Interrupt Link [INTB] (IRQs 3 4 5 7 10 11 12 15) *0 [ 0.258755] ACPI: PCI Interrupt Link [INTC] (IRQs 3 4 5 7 10 11 12 15) *0 [ 0.259010] ACPI: PCI Interrupt Link [INTD] (IRQs 3 4 5 7 10 11 12 15) *0 [ 0.259263] ACPI: PCI Interrupt Link [INTE] (IRQs 3 4 5 7 10 11 12 15) *0 [ 0.259517] ACPI: PCI Interrupt Link [INTF] (IRQs 9) *0 [ 0.259763] ACPI: PCI Interrupt Link [INTG] (IRQs 3 4 5 7 10 11 12 15) *0 [ 0.260015] ACPI: PCI Interrupt Link [INTH] (IRQs 3 4 5 7 10 11 12 15) *0 [ 0.260240] acpi PNP0A03:00: [Firmware Bug]: no secondary bus range in _CRS [ 0.260267] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.260283] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI] [ 0.260523] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability] [ 0.261381] PCI host bridge to bus 0000:00 [ 0.261392] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.261400] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.261407] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.261429] pci 0000:00:00.0: [1022:1510] type 00 class 0x060000 [ 0.261803] pci 0000:00:04.0: [1022:1512] type 01 class 0x060400 [ 0.261933] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold [ 0.262087] pci 0000:00:04.0: System wakeup disabled by ACPI [ 0.262237] pci 0000:00:05.0: [1022:1513] type 01 class 0x060400 [ 0.262350] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold [ 0.262497] pci 0000:00:05.0: System wakeup disabled by ACPI [ 0.262641] pci 0000:00:06.0: [1022:1514] type 01 class 0x060400 [ 0.262754] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold [ 0.262901] pci 0000:00:06.0: System wakeup disabled by ACPI [ 0.263110] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601 [ 0.263145] pci 0000:00:11.0: reg 0x10: [io 0x4020-0x4027] [ 0.263164] pci 0000:00:11.0: reg 0x14: [io 0x4040-0x4043] [ 0.263182] pci 0000:00:11.0: reg 0x18: [io 0x4028-0x402f] [ 0.263199] pci 0000:00:11.0: reg 0x1c: [io 0x4044-0x4047] [ 0.263217] pci 0000:00:11.0: reg 0x20: [io 0x4000-0x400f] [ 0.263236] pci 0000:00:11.0: reg 0x24: [mem 0xfeb08000-0xfeb083ff] [ 0.263602] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 [ 0.263628] pci 0000:00:12.0: reg 0x10: [mem 0xfeb04000-0xfeb04fff] [ 0.263853] pci 0000:00:12.0: System wakeup disabled by ACPI [ 0.264048] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 [ 0.264082] pci 0000:00:12.2: reg 0x10: [mem 0xfeb08400-0xfeb084ff] [ 0.264220] pci 0000:00:12.2: supports D1 D2 [ 0.264226] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.264370] pci 0000:00:12.2: System wakeup disabled by ACPI [ 0.264565] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 [ 0.264590] pci 0000:00:13.0: reg 0x10: [mem 0xfeb05000-0xfeb05fff] [ 0.264815] pci 0000:00:13.0: System wakeup disabled by ACPI [ 0.265012] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 [ 0.265045] pci 0000:00:13.2: reg 0x10: [mem 0xfeb08500-0xfeb085ff] [ 0.265182] pci 0000:00:13.2: supports D1 D2 [ 0.265188] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.265337] pci 0000:00:13.2: System wakeup disabled by ACPI [ 0.265529] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 [ 0.265929] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a [ 0.265955] pci 0000:00:14.1: reg 0x10: [io 0x4030-0x4037] [ 0.265973] pci 0000:00:14.1: reg 0x14: [io 0x4048-0x404b] [ 0.265991] pci 0000:00:14.1: reg 0x18: [io 0x4038-0x403f] [ 0.266008] pci 0000:00:14.1: reg 0x1c: [io 0x404c-0x404f] [ 0.266026] pci 0000:00:14.1: reg 0x20: [io 0x4010-0x401f] [ 0.266060] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.266066] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.266072] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.266078] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.266434] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 [ 0.266829] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 [ 0.267026] pci 0000:00:14.4: System wakeup disabled by ACPI [ 0.267210] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 [ 0.267235] pci 0000:00:14.5: reg 0x10: [mem 0xfeb06000-0xfeb06fff] [ 0.267467] pci 0000:00:14.5: System wakeup disabled by ACPI [ 0.267664] pci 0000:00:15.0: [1002:43a0] type 01 class 0x060400 [ 0.267805] pci 0000:00:15.0: supports D1 D2 [ 0.267955] pci 0000:00:15.0: System wakeup disabled by ACPI [ 0.268139] pci 0000:00:16.0: [1002:4397] type 00 class 0x0c0310 [ 0.268165] pci 0000:00:16.0: reg 0x10: [mem 0xfeb07000-0xfeb07fff] [ 0.268391] pci 0000:00:16.0: System wakeup disabled by ACPI [ 0.268588] pci 0000:00:16.2: [1002:4396] type 00 class 0x0c0320 [ 0.268622] pci 0000:00:16.2: reg 0x10: [mem 0xfeb08600-0xfeb086ff] [ 0.268759] pci 0000:00:16.2: supports D1 D2 [ 0.268765] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot [ 0.268909] pci 0000:00:16.2: System wakeup disabled by ACPI [ 0.269107] pci 0000:00:18.0: [1022:1700] type 00 class 0x060000 [ 0.269393] pci 0000:00:18.1: [1022:1701] type 00 class 0x060000 [ 0.269672] pci 0000:00:18.2: [1022:1702] type 00 class 0x060000 [ 0.269965] pci 0000:00:18.3: [1022:1703] type 00 class 0x060000 [ 0.270262] pci 0000:00:18.4: [1022:1704] type 00 class 0x060000 [ 0.270543] pci 0000:00:18.5: [1022:1718] type 00 class 0x060000 [ 0.270820] pci 0000:00:18.6: [1022:1716] type 00 class 0x060000 [ 0.271094] pci 0000:00:18.7: [1022:1719] type 00 class 0x060000 [ 0.271583] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 0.271613] pci 0000:01:00.0: reg 0x10: [io 0x1000-0x10ff] [ 0.271651] pci 0000:01:00.0: reg 0x18: [mem 0xfe600000-0xfe600fff 64bit] [ 0.271676] pci 0000:01:00.0: reg 0x20: [mem 0xfe500000-0xfe503fff 64bit pref] [ 0.271806] pci 0000:01:00.0: supports D1 D2 [ 0.271813] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.278150] pci 0000:00:04.0: PCI bridge to [bus 01] [ 0.278172] pci 0000:00:04.0: bridge window [io 0x1000-0x1fff] [ 0.278182] pci 0000:00:04.0: bridge window [mem 0xfe600000-0xfe6fffff] [ 0.278195] pci 0000:00:04.0: bridge window [mem 0xfe500000-0xfe5fffff 64bit pref] [ 0.278421] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 0.278455] pci 0000:02:00.0: reg 0x10: [io 0x2000-0x20ff] [ 0.278493] pci 0000:02:00.0: reg 0x18: [mem 0xfe800000-0xfe800fff 64bit] [ 0.278519] pci 0000:02:00.0: reg 0x20: [mem 0xfe700000-0xfe703fff 64bit pref] [ 0.278670] pci 0000:02:00.0: supports D1 D2 [ 0.278677] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.286149] pci 0000:00:05.0: PCI bridge to [bus 02] [ 0.286172] pci 0000:00:05.0: bridge window [io 0x2000-0x2fff] [ 0.286182] pci 0000:00:05.0: bridge window [mem 0xfe800000-0xfe8fffff] [ 0.286195] pci 0000:00:05.0: bridge window [mem 0xfe700000-0xfe7fffff 64bit pref] [ 0.286421] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000 [ 0.286455] pci 0000:03:00.0: reg 0x10: [io 0x3000-0x30ff] [ 0.286493] pci 0000:03:00.0: reg 0x18: [mem 0xfea00000-0xfea00fff 64bit] [ 0.286519] pci 0000:03:00.0: reg 0x20: [mem 0xfe900000-0xfe903fff 64bit pref] [ 0.286670] pci 0000:03:00.0: supports D1 D2 [ 0.286677] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.294149] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.294171] pci 0000:00:06.0: bridge window [io 0x3000-0x3fff] [ 0.294181] pci 0000:00:06.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.294194] pci 0000:00:06.0: bridge window [mem 0xfe900000-0xfe9fffff 64bit pref] [ 0.294257] pci 0000:00:14.4: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.294529] pci 0000:00:15.0: PCI bridge to [bus 04] [ 0.294780] pci 0000:00:14.4: PCI bridge to [bus 05-ff] (subtractive decode) [ 0.294794] pci 0000:00:14.4: bridge window [mem 0x00000000-0x000fffff] [ 0.294804] pci 0000:00:14.4: bridge window [mem 0x00000000-0x000fffff pref] [ 0.294812] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.294819] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.294827] pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 05 [ 0.296048] ACPI: Enabled 6 GPEs in block 00 to 1F [ 0.296671] vgaarb: loaded [ 0.297149] PCI: Using ACPI for IRQ routing [ 0.297165] PCI: pci_cache_line_size set to 64 bytes [ 0.297182] pci 0000:00:04.0: can't claim BAR 14 [mem 0xfe600000-0xfe6fffff]: no compatible bridge window [ 0.297192] pci 0000:00:04.0: can't claim BAR 15 [mem 0xfe500000-0xfe5fffff 64bit pref]: no compatible bridge window [ 0.297202] pci 0000:00:05.0: can't claim BAR 14 [mem 0xfe800000-0xfe8fffff]: no compatible bridge window [ 0.297210] pci 0000:00:05.0: can't claim BAR 15 [mem 0xfe700000-0xfe7fffff 64bit pref]: no compatible bridge window [ 0.297218] pci 0000:00:06.0: can't claim BAR 14 [mem 0xfea00000-0xfeafffff]: no compatible bridge window [ 0.297226] pci 0000:00:06.0: can't claim BAR 15 [mem 0xfe900000-0xfe9fffff 64bit pref]: no compatible bridge window [ 0.297243] pci 0000:01:00.0: can't claim BAR 2 [mem 0xfe600000-0xfe600fff 64bit]: no compatible bridge window [ 0.297253] pci 0000:01:00.0: can't claim BAR 4 [mem 0xfe500000-0xfe503fff 64bit pref]: no compatible bridge window [ 0.297265] pci 0000:02:00.0: can't claim BAR 2 [mem 0xfe800000-0xfe800fff 64bit]: no compatible bridge window [ 0.297273] pci 0000:02:00.0: can't claim BAR 4 [mem 0xfe700000-0xfe703fff 64bit pref]: no compatible bridge window [ 0.297285] pci 0000:03:00.0: can't claim BAR 2 [mem 0xfea00000-0xfea00fff 64bit]: no compatible bridge window [ 0.297296] pci 0000:03:00.0: can't claim BAR 4 [mem 0xfe900000-0xfe903fff 64bit pref]: no compatible bridge window [ 0.297355] pci 0000:00:11.0: can't claim BAR 5 [mem 0xfeb08000-0xfeb083ff]: no compatible bridge window [ 0.297365] pci 0000:00:12.0: can't claim BAR 0 [mem 0xfeb04000-0xfeb04fff]: no compatible bridge window [ 0.297376] pci 0000:00:12.2: can't claim BAR 0 [mem 0xfeb08400-0xfeb084ff]: no compatible bridge window [ 0.297386] pci 0000:00:13.0: can't claim BAR 0 [mem 0xfeb05000-0xfeb05fff]: no compatible bridge window [ 0.297396] pci 0000:00:13.2: can't claim BAR 0 [mem 0xfeb08500-0xfeb085ff]: no compatible bridge window [ 0.297419] pci 0000:00:14.5: can't claim BAR 0 [mem 0xfeb06000-0xfeb06fff]: no compatible bridge window [ 0.297432] pci 0000:00:16.0: can't claim BAR 0 [mem 0xfeb07000-0xfeb07fff]: no compatible bridge window [ 0.297443] pci 0000:00:16.2: can't claim BAR 0 [mem 0xfeb08600-0xfeb086ff]: no compatible bridge window [ 0.297508] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff] [ 0.297515] e820: reserve RAM buffer [mem 0x7e16ec00-0x7fffffff] [ 0.298086] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.298098] hpet0: 3 comparators, 32-bit 14.318180 MHz counter [ 0.300395] Switched to clocksource hpet [ 0.307246] pnp: PnP ACPI init [ 0.308354] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.308427] pnp: PnP ACPI: found 1 devices [ 0.327676] pci 0000:00:04.0: BAR 14: no space for [mem size 0x00100000] [ 0.327693] pci 0000:00:04.0: BAR 14: failed to assign [mem size 0x00100000] [ 0.327703] pci 0000:00:04.0: BAR 15: no space for [mem size 0x00100000 64bit pref] [ 0.327711] pci 0000:00:04.0: BAR 15: failed to assign [mem size 0x00100000 64bit pref] [ 0.327719] pci 0000:00:05.0: BAR 14: no space for [mem size 0x00100000] [ 0.327726] pci 0000:00:05.0: BAR 14: failed to assign [mem size 0x00100000] [ 0.327734] pci 0000:00:05.0: BAR 15: no space for [mem size 0x00100000 64bit pref] [ 0.327741] pci 0000:00:05.0: BAR 15: failed to assign [mem size 0x00100000 64bit pref] [ 0.327749] pci 0000:00:06.0: BAR 14: no space for [mem size 0x00100000] [ 0.327755] pci 0000:00:06.0: BAR 14: failed to assign [mem size 0x00100000] [ 0.327763] pci 0000:00:06.0: BAR 15: no space for [mem size 0x00100000 64bit pref] [ 0.327769] pci 0000:00:06.0: BAR 15: failed to assign [mem size 0x00100000 64bit pref] [ 0.327777] pci 0000:00:12.0: BAR 0: no space for [mem size 0x00001000] [ 0.327784] pci 0000:00:12.0: BAR 0: trying firmware assignment [mem size 0x00001000] [ 0.327793] pci 0000:00:12.0: BAR 0: assigned [mem 0xfeb04000-0xfeb04fff] [ 0.327852] pci 0000:00:13.0: BAR 0: no space for [mem size 0x00001000] [ 0.327859] pci 0000:00:13.0: BAR 0: trying firmware assignment [mem size 0x00001000] [ 0.327865] pci 0000:00:13.0: BAR 0: assigned [mem 0xfeb05000-0xfeb05fff] [ 0.327876] pci 0000:00:14.5: BAR 0: no space for [mem size 0x00001000] [ 0.327882] pci 0000:00:14.5: BAR 0: trying firmware assignment [mem size 0x00001000] [ 0.327889] pci 0000:00:14.5: BAR 0: assigned [mem 0xfeb06000-0xfeb06fff] [ 0.327900] pci 0000:00:16.0: BAR 0: no space for [mem size 0x00001000] [ 0.327906] pci 0000:00:16.0: BAR 0: trying firmware assignment [mem size 0x00001000] [ 0.327912] pci 0000:00:16.0: BAR 0: assigned [mem 0xfeb07000-0xfeb07fff] [ 0.327923] pci 0000:00:11.0: BAR 5: no space for [mem size 0x00000400] [ 0.327929] pci 0000:00:11.0: BAR 5: trying firmware assignment [mem size 0x00000400] [ 0.327936] pci 0000:00:11.0: BAR 5: assigned [mem 0xfeb08000-0xfeb083ff] [ 0.327947] pci 0000:00:12.2: BAR 0: no space for [mem size 0x00000100] [ 0.327953] pci 0000:00:12.2: BAR 0: trying firmware assignment [mem size 0x00000100] [ 0.327959] pci 0000:00:12.2: BAR 0: assigned [mem 0xfeb08400-0xfeb084ff] [ 0.327970] pci 0000:00:13.2: BAR 0: no space for [mem size 0x00000100] [ 0.327976] pci 0000:00:13.2: BAR 0: trying firmware assignment [mem size 0x00000100] [ 0.327982] pci 0000:00:13.2: BAR 0: assigned [mem 0xfeb08500-0xfeb085ff] [ 0.327993] pci 0000:00:16.2: BAR 0: no space for [mem size 0x00000100] [ 0.328000] pci 0000:00:16.2: BAR 0: trying firmware assignment [mem size 0x00000100] [ 0.328006] pci 0000:00:16.2: BAR 0: assigned [mem 0xfeb08600-0xfeb086ff] [ 0.328021] pci 0000:01:00.0: BAR 4: no space for [mem size 0x00004000 64bit pref] [ 0.328028] pci 0000:01:00.0: BAR 4: trying firmware assignment [mem size 0x00004000 64bit pref] [ 0.328035] pci 0000:01:00.0: BAR 4: assigned [mem 0xfe500000-0xfe503fff 64bit pref] [ 0.328054] pci 0000:01:00.0: BAR 2: no space for [mem size 0x00001000 64bit] [ 0.328061] pci 0000:01:00.0: BAR 2: trying firmware assignment [mem size 0x00001000 64bit] [ 0.328067] pci 0000:01:00.0: BAR 2: assigned [mem 0xfe600000-0xfe600fff 64bit] [ 0.328087] pci 0000:00:04.0: PCI bridge to [bus 01] [ 0.328095] pci 0000:00:04.0: bridge window [io 0x1000-0x1fff] [ 0.328115] pci 0000:02:00.0: BAR 4: no space for [mem size 0x00004000 64bit pref] [ 0.328122] pci 0000:02:00.0: BAR 4: trying firmware assignment [mem size 0x00004000 64bit pref] [ 0.328129] pci 0000:02:00.0: BAR 4: assigned [mem 0xfe700000-0xfe703fff 64bit pref] [ 0.328148] pci 0000:02:00.0: BAR 2: no space for [mem size 0x00001000 64bit] [ 0.328154] pci 0000:02:00.0: BAR 2: trying firmware assignment [mem size 0x00001000 64bit] [ 0.328161] pci 0000:02:00.0: BAR 2: assigned [mem 0xfe800000-0xfe800fff 64bit] [ 0.328179] pci 0000:00:05.0: PCI bridge to [bus 02] [ 0.328186] pci 0000:00:05.0: bridge window [io 0x2000-0x2fff] [ 0.328205] pci 0000:03:00.0: BAR 4: no space for [mem size 0x00004000 64bit pref] [ 0.328212] pci 0000:03:00.0: BAR 4: trying firmware assignment [mem size 0x00004000 64bit pref] [ 0.328218] pci 0000:03:00.0: BAR 4: assigned [mem 0xfe900000-0xfe903fff 64bit pref] [ 0.328237] pci 0000:03:00.0: BAR 2: no space for [mem size 0x00001000 64bit] [ 0.328244] pci 0000:03:00.0: BAR 2: trying firmware assignment [mem size 0x00001000 64bit] [ 0.328250] pci 0000:03:00.0: BAR 2: assigned [mem 0xfea00000-0xfea00fff 64bit] [ 0.328328] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.328336] pci 0000:00:06.0: bridge window [io 0x3000-0x3fff] [ 0.328353] pci 0000:00:14.4: PCI bridge to [bus 05] [ 0.328375] pci 0000:00:15.0: PCI bridge to [bus 04] [ 0.328396] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc [ 0.328404] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.328410] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.328417] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff] [ 0.328423] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff] [ 0.328430] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff] [ 0.328437] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7 window] [ 0.328443] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff window] [ 0.328658] NET: Registered protocol family 2 [ 0.329181] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.329351] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 0.329541] TCP: Hash tables configured (established 16384 bind 16384) [ 0.329660] TCP: reno registered [ 0.329682] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 0.329726] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 0.330065] NET: Registered protocol family 1 [ 0.332601] PCI: CLS 64 bytes, default 64 [ 0.332769] Unpacking initramfs... [ 1.207463] Freeing initrd memory: 14764K (ffff88003631a000 - ffff880037185000) [ 1.208453] microcode: CPU0: patch_level=0x05000101 [ 1.208482] microcode: CPU1: patch_level=0x05000101 [ 1.208793] microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba [ 1.208818] LVT offset 0 assigned for vector 0x400 [ 1.208946] perf: AMD IBS detected (0x000000ff) [ 1.210286] futex hash table entries: 512 (order: 3, 32768 bytes) [ 1.210467] audit: initializing netlink subsys (disabled) [ 1.210532] audit: type=2000 audit(1426719194.104:1): initialized [ 1.211808] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.212576] VFS: Disk quotas dquot_6.5.2 [ 1.212692] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.214563] alg: No test for stdrng (krng) [ 1.214667] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.214812] io scheduler noop registered [ 1.214822] io scheduler deadline registered [ 1.214855] io scheduler cfq registered (default) [ 1.217141] pcieport 0000:00:04.0: Signaling PME through PCIe PME interrupt [ 1.217149] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.217160] pcie_pme 0000:00:04.0:pcie01: service driver pcie_pme loaded [ 1.217215] pcieport 0000:00:05.0: Signaling PME through PCIe PME interrupt [ 1.217222] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 1.217231] pcie_pme 0000:00:05.0:pcie01: service driver pcie_pme loaded [ 1.217274] pcieport 0000:00:06.0: Signaling PME through PCIe PME interrupt [ 1.217280] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt [ 1.217289] pcie_pme 0000:00:06.0:pcie01: service driver pcie_pme loaded [ 1.217382] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt [ 1.217392] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded [ 1.217419] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.217482] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 1.217684] GHES: Failed to enable APEI firmware first mode. [ 1.218013] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.238736] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 1.259769] serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.261525] Linux agpgart interface v0.103 [ 1.261766] AMD IOMMUv2 driver by Joerg Roedel <jroedel@xxxxxxx> [ 1.261771] AMD IOMMUv2 functionality not available on this system [ 1.261954] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 2.204419] tsc: Refined TSC clocksource calibration: 999.999 MHz [ 3.205323] i8042: No controller found [ 3.209117] Switched to clocksource tsc [ 3.209596] mousedev: PS/2 mouse device common for all mice [ 3.209744] rtc_cmos 00:00: RTC can wake from S4 [ 3.210136] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0 [ 3.210236] rtc_cmos 00:00: alarms up to one day, 114 bytes nvram, hpet irqs [ 3.210429] TCP: cubic registered [ 3.210545] NET: Registered protocol family 10 [ 3.211325] mip6: Mobile IPv6 [ 3.211344] NET: Registered protocol family 17 [ 3.211360] mpls_gso: MPLS GSO support [ 3.212572] registered taskstats version 1 [ 3.213725] rtc_cmos 00:00: setting system clock to 2015-03-18 22:53:16 UTC (1426719196) [ 3.213831] PM: Hibernation image not present or could not be loaded. [ 3.215018] Freeing unused kernel memory: 1020K (ffffffff818ba000 - ffffffff819b9000) [ 3.215030] Write protecting the kernel read-only data: 8192k [ 3.216174] Freeing unused kernel memory: 868K (ffff880001527000 - ffff880001600000) [ 3.216639] Freeing unused kernel memory: 288K (ffff8800017b8000 - ffff880001800000) [ 3.455783] udevd[64]: starting version 175 [ 3.522897] ACPI: bus type USB registered [ 3.523006] usbcore: registered new interface driver usbfs [ 3.523046] usbcore: registered new interface driver hub [ 3.526771] SCSI subsystem initialized [ 3.533232] usbcore: registered new device driver usb [ 3.534513] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.535446] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.536131] ohci-pci: OHCI PCI platform driver [ 3.536243] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.536253] QUIRK: Enable AMD PLL fix [ 3.537141] ehci-pci: EHCI PCI platform driver [ 3.537256] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 3.537278] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 3.537475] ohci-pci 0000:00:12.0: irq 18, io mem 0xfeb04000 [ 3.547535] r8169 0000:01:00.0 (unnamed net_device) (uninitialized): unknown MAC, using family default [ 3.562301] r8169 0000:01:00.0 (unnamed net_device) (uninitialized): rtl_chipcmd_cond == 1 (loop: 100, delay: 100). [ 3.563380] libata version 3.00 loaded. [ 3.596901] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.596915] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.596923] usb usb1: Product: OHCI PCI host controller [ 3.596930] usb usb1: Manufacturer: Linux 4.0.0-rc4 ohci_hcd [ 3.596936] usb usb1: SerialNumber: 0000:00:12.0 [ 3.597486] hub 1-0:1.0: USB hub found [ 3.597569] hub 1-0:1.0: 5 ports detected [ 3.598621] ehci-pci 0000:00:12.2: EHCI Host Controller [ 3.598642] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 3.598659] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 3.598727] ehci-pci 0000:00:12.2: debug port 1 [ 3.598821] ehci-pci 0000:00:12.2: irq 17, io mem 0xfeb08400 [ 3.608379] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 3.608525] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.608535] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.608542] usb usb2: Product: EHCI Host Controller [ 3.608548] usb usb2: Manufacturer: Linux 4.0.0-rc4 ehci_hcd [ 3.608554] usb usb2: SerialNumber: 0000:00:12.2 [ 3.608992] hub 2-0:1.0: USB hub found [ 3.609017] hub 2-0:1.0: 5 ports detected [ 3.629427] r8169 0000:01:00.0 eth0: RTL8168b/8111b at 0xffffc90000324000, ff:ff:ff:ff:ff:ff, XID 9cf0f8ff IRQ 28 [ 3.629441] r8169 0000:01:00.0 eth0: jumbo features [frames: 4080 bytes, tx checksumming: ko] [ 3.629514] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.629809] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): unknown MAC, using family default [ 3.644577] r8169 0000:02:00.0 (unnamed net_device) (uninitialized): rtl_chipcmd_cond == 1 (loop: 100, delay: 100). [ 3.684636] hub 1-0:1.0: USB hub found [ 3.684719] hub 1-0:1.0: 5 ports detected [ 3.685278] ehci-pci 0000:00:13.2: EHCI Host Controller [ 3.685299] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 3.685316] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 3.685384] ehci-pci 0000:00:13.2: debug port 1 [ 3.685450] ehci-pci 0000:00:13.2: irq 17, io mem 0xfeb08500 [ 3.696412] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 3.696543] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.696551] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.696558] usb usb3: Product: EHCI Host Controller [ 3.696564] usb usb3: Manufacturer: Linux 4.0.0-rc4 ehci_hcd [ 3.696570] usb usb3: SerialNumber: 0000:00:13.2 [ 3.697002] hub 3-0:1.0: USB hub found [ 3.697029] hub 3-0:1.0: 5 ports detected [ 3.697681] ehci-pci 0000:00:16.2: EHCI Host Controller [ 3.697704] ehci-pci 0000:00:16.2: new USB bus registered, assigned bus number 4 [ 3.697720] ehci-pci 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 3.697787] ehci-pci 0000:00:16.2: debug port 1 [ 3.697851] ehci-pci 0000:00:16.2: irq 17, io mem 0xfeb08600 [ 3.706721] r8169 0000:02:00.0 eth1: RTL8168b/8111b at 0xffffc900003b4000, ff:ff:ff:ff:ff:ff, XID 9cf0f8ff IRQ 29 [ 3.706736] r8169 0000:02:00.0 eth1: jumbo features [frames: 4080 bytes, tx checksumming: ko] [ 3.706799] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.707087] r8169 0000:03:00.0 (unnamed net_device) (uninitialized): unknown MAC, using family default [ 3.721569] r8169 0000:03:00.0 (unnamed net_device) (uninitialized): rtl_chipcmd_cond == 1 (loop: 100, delay: 100). [ 3.732215] ehci-pci 0000:00:16.2: USB 2.0 started, EHCI 1.00 [ 3.732329] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.732336] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.732343] usb usb4: Product: EHCI Host Controller [ 3.732349] usb usb4: Manufacturer: Linux 4.0.0-rc4 ehci_hcd [ 3.732355] usb usb4: SerialNumber: 0000:00:16.2 [ 3.732788] hub 4-0:1.0: USB hub found [ 3.732814] hub 4-0:1.0: 4 ports detected [ 3.734124] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 3.734149] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 3.734265] ohci-pci 0000:00:13.0: irq 18, io mem 0xfeb05000 [ 3.736070] r8169 0000:03:00.0 eth2: RTL8168b/8111b at 0xffffc90000418000, ff:ff:ff:ff:ff:ff, XID 9cf0f8ff IRQ 30 [ 3.736083] r8169 0000:03:00.0 eth2: jumbo features [frames: 4080 bytes, tx checksumming: ko] [ 3.792729] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.792743] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.792750] usb usb5: Product: OHCI PCI host controller [ 3.792756] usb usb5: Manufacturer: Linux 4.0.0-rc4 ohci_hcd [ 3.792762] usb usb5: SerialNumber: 0000:00:13.0 [ 3.793465] hub 5-0:1.0: USB hub found [ 3.793546] hub 5-0:1.0: 5 ports detected [ 3.797752] scsi host0: pata_atiixp [ 3.798207] scsi host1: pata_atiixp [ 3.798379] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4010 irq 14 [ 3.798385] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x4018 irq 15 [ 3.798455] ahci 0000:00:11.0: version 3.0 [ 3.799145] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode [ 3.799156] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck led clo pmp pio slum part [ 3.801501] scsi host2: ahci [ 3.802169] scsi host3: ahci [ 3.802671] scsi host4: ahci [ 3.803093] scsi host5: ahci [ 3.803294] ata3: SATA max UDMA/133 abar m1024@0xfeb08000 port 0xfeb08100 irq 19 [ 3.803303] ata4: SATA max UDMA/133 abar m1024@0xfeb08000 port 0xfeb08180 irq 19 [ 3.803310] ata5: SATA max UDMA/133 abar m1024@0xfeb08000 port 0xfeb08200 irq 19 [ 3.803318] ata6: SATA max UDMA/133 abar m1024@0xfeb08000 port 0xfeb08280 irq 19 [ 3.803613] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 3.803633] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 6 [ 3.804368] ohci-pci 0000:00:14.5: irq 18, io mem 0xfeb06000 [ 3.864715] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.864728] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.864736] usb usb6: Product: OHCI PCI host controller [ 3.864742] usb usb6: Manufacturer: Linux 4.0.0-rc4 ohci_hcd [ 3.864748] usb usb6: SerialNumber: 0000:00:14.5 [ 3.865483] hub 6-0:1.0: USB hub found [ 3.865565] hub 6-0:1.0: 2 ports detected [ 3.866057] ohci-pci 0000:00:16.0: OHCI PCI host controller [ 3.866077] ohci-pci 0000:00:16.0: new USB bus registered, assigned bus number 7 [ 3.866197] ohci-pci 0000:00:16.0: irq 18, io mem 0xfeb07000 [ 3.924720] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.924734] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.924742] usb usb7: Product: OHCI PCI host controller [ 3.924748] usb usb7: Manufacturer: Linux 4.0.0-rc4 ohci_hcd [ 3.924754] usb usb7: SerialNumber: 0000:00:16.0 [ 3.925498] hub 7-0:1.0: USB hub found [ 3.925580] hub 7-0:1.0: 4 ports detected [ 3.940427] usb 2-2: new high-speed USB device number 2 using ehci-pci [ 4.044593] usb 4-1: new high-speed USB device number 2 using ehci-pci [ 4.120342] ata6: SATA link down (SStatus 0 SControl 300) [ 4.120425] ata4: SATA link down (SStatus 0 SControl 300) [ 4.124579] ata5: SATA link down (SStatus 0 SControl 300) [ 4.157871] usb 2-2: New USB device found, idVendor=413c, idProduct=8147 [ 4.157888] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.157896] usb 2-2: Product: Dell Wireless 5530 HSPA Mobile Broadband Minicard Device [ 4.157902] usb 2-2: Manufacturer: Dell [ 4.157908] usb 2-2: SerialNumber: 3558620263894800 [ 4.179966] usb 4-1: New USB device found, idVendor=058f, idProduct=6366 [ 4.179983] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.179992] usb 4-1: Product: Flash Card Reader/Writer [ 4.179999] usb 4-1: Manufacturer: Generic [ 4.180007] usb 4-1: SerialNumber: 058F63666485 [ 4.188669] usb-storage 4-1:1.0: USB Mass Storage device detected [ 4.189222] scsi host6: usb-storage 4-1:1.0 [ 4.189502] usbcore: registered new interface driver usb-storage [ 4.292573] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 4.308084] ata3.00: ATA-8: KINGSTON SMS200S330G, 524ABBF0, max UDMA/133 [ 4.308097] ata3.00: 58626288 sectors, multi 1: LBA48 NCQ (depth 31/32), AA [ 4.318759] ata3.00: configured for UDMA/133 [ 4.319429] scsi 2:0:0:0: Direct-Access ATA KINGSTON SMS200S BBF0 PQ: 0 ANSI: 5 [ 4.334582] sd 2:0:0:0: [sda] 58626288 512-byte logical blocks: (30.0 GB/27.9 GiB) [ 4.334974] sd 2:0:0:0: [sda] Write Protect is off [ 4.334993] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.335059] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.336525] sda: sda1 sda2 < sda5 > [ 4.337966] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.343430] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.447464] device-mapper: uevent: version 1.0.3 [ 4.447690] device-mapper: ioctl: 4.30.0-ioctl (2014-12-22) initialised: dm-devel@xxxxxxxxxx [ 4.479402] PM: Starting manual resume from disk [ 4.479418] PM: Hibernation image partition 8:5 present [ 4.479422] PM: Looking for hibernation image. [ 4.480214] PM: Image not found (code -22) [ 4.480226] PM: Hibernation image not present or could not be loaded. [ 4.506652] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 5.030219] udevd[393]: starting version 175 [ 5.189785] scsi 6:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 4 [ 5.192342] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 5.195006] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 5.239569] ACPI: acpi_idle registered with cpuidle [ 5.243090] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 5.243108] ACPI: Power Button [PWRB] [ 5.244453] acpi-cpufreq: overriding BIOS provided _PSD data [ 5.249457] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 5.249475] ACPI: Power Button [PWRF] [ 5.484106] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 [ 5.490025] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20 [ 5.499979] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05 [ 5.500146] sp5100_tco: PCI Revision ID: 0x42 [ 5.500251] sp5100_tco: Using 0xfed80b00 for watchdog MMIO address [ 5.500373] sp5100_tco: Last reboot was not triggered by watchdog. [ 5.505115] sp5100_tco: initialized (0xffffc900003b0b00). heartbeat=60 sec (nowayout=0) [ 5.578150] kvm: Nested Virtualization enabled [ 5.578167] kvm: Nested Paging enabled [ 5.580615] cdc_wdm 2-2:1.5: cdc-wdm0: USB WDM device [ 5.580774] cdc_wdm 2-2:1.6: cdc-wdm1: USB WDM device [ 5.580837] usbcore: registered new interface driver cdc_wdm [ 5.582337] cdc_acm 2-2:1.1: ttyACM0: USB ACM device [ 5.583380] cdc_acm 2-2:1.3: ttyACM1: USB ACM device [ 5.584829] cdc_acm 2-2:1.9: ttyACM2: USB ACM device [ 5.585961] usbcore: registered new interface driver cdc_acm [ 5.585972] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 5.624990] cdc_ether 2-2:1.7 wwan0: register 'cdc_ether' at usb-0000:00:12.2-2, Mobile Broadband Network Device, 02:80:37:ec:02:00 [ 5.625096] usbcore: registered new interface driver cdc_ether [ 6.711926] Adding 1239036k swap on /dev/sda5. Priority:-1 extents:1 across:1239036k SS [ 6.765958] EXT4-fs (sda1): re-mounted. Opts: (null) [ 6.875075] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 7.172956] loop: module loaded [ 7.189581] random: vgscan urandom read with 35 bits of entropy available [ 10.540648] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.569052] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.603131] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 10.612636] Bridge firewalling registered [ 10.652079] device eth0 entered promiscuous mode [ 10.655679] device eth2 entered promiscuous mode [ 222.938623] random: nonblocking pool is initialized
00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:05.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:06.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (rev 40) 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:15.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) 00:16.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
