Re: intel 537 with kernel 3.1.x

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Will certainly do that Philippe.

While the driver installed okay here is my output from wvdial and wvdialconf:

[root@pb3000 etc]# wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S2   S3


Sorry, no modem was detected!  Is it in use by another program?
Did you configure it properly with setserial?

Please read the FAQ at http://alumnit.ca/wiki/?WvDial
[root@pb3000 etc]# wvdial
--> WvDial: Internet dialer version 1.61
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Modem initialized.
--> Sending: ATDT4164648392
--> Waiting for carrier.
ATDT4164648392

Message from syslogd@pb3000 at Jan  4 11:58:38 ...
 kernel:[ 1272.590289] Disabling IRQ #19
NO DIALTONE
--> No dial tone.
--> Disconnecting at Wed Jan  4 11:58:46 2012



...should I have some symbolic link to /dev/tty*** ?

Patrick


On Wed, Jan 04, 2012 at 03:23:19PM +0100, Philippe Vouters wrote:
> Patrick,
> 
> >> If there is anything I can ever do to repay you please let me know!
> 
> Yes, indeed, you can repay us by attentively redeading my
> litterature on the Intel modems subject at
> http://vouters.dyndns.org/Intel/Intel-Readme.html and give us your
> feedback upon it.
> 
> What we do expect are your detailled impressions about this document
> clarity and informations completeness.
> 
> Post-scriptum : if you are looking for informations on either Linux,
> Unix, OpenVMS or Windows, you may refer to another side of my Web
> site at http://vouters.dyndns.org/tima/
> If, even better, you mail me with technical subjects I can study and
> document, you'll make the worldwide IT community happy.
> 
> Yours truly,
> Philippe
> 
> Le 04/01/2012 14:46, Patrick Boyadjian a écrit :
> >Brilliant, it works!
> >
> >Philippe and Antonio, thank you so much for your support in this regard!
> >
> >If there is anything I can ever do to repay you please let me know!
> >
> >Regards,
> >Patrick
> >
> >
> >
> >On Wed, Jan 04, 2012 at 12:27:39PM +0100, Philippe Vouters wrote:
> >>My work ought to support your modem.
> >>[philippe@victor ~]$ grep e159:0001 intel-536-537/*
> >>intel-536-537/makefile_537:     vendor_device_ids[0]="e159:0001";\
> >>
> >>The alternative to modifying the bash files is to download
> >>http://vouters.dyndns.org/Intel/intel-536EP-537EP_2012_01_04.tar.bz2
> >>
> >>Please reply whether you are fully satisfied or not.
> >>
> >>Regards,
> >>Philippe
> >>
> >>Le 04/01/2012 04:03, Patrick Boyadjian a écrit :
> >>>Thanks for the swift reply Antonio.
> >>>
> >>>Well originally I had a conexant chipset for a HCF modem that the linuxant group had drivers for, however those drivers ONLY worked on pre 3.x kernels so they broke when I upgraded.  Dev team from Linuxant has informed me they are aware of the API break in the driver for the newer kernel and say they should fix it sometime soon.  Meanwhile I dug up the Intel modem you see below to try and get it to work.
> >>>
> >>>So short answer I never should have upgraded!! :)
> >>>
> >>>Regards,
> >>>Patrick
> >>>
> >>>
> >>>
> >>>On Tue, Jan 03, 2012 at 07:47:12PM -0600, Antonio Olivares wrote:
> >>>>Patrick,
> >>>>
> >>>>I am unsure if that modem in particular is served by Phillipe's
> >>>>driver.  IT does not seem to be a true INTEL 537 modem :(
> >>>>However, there was a recent update to the driver since it was failing
> >>>>to build up in Ubuntu and it was working fine in Fedora 15.  Did you
> >>>>make sure that you got the latest driver available from Phillipe's
> >>>>website?
> >>>>
> >>>>Oops sorry, you did get the latest one. Maybe Phillipe can comment
> >>>>here to make sure that maybe something went wrong, or that it may be
> >>>>specific to 537 modem, since the driver also works with 536 Intel
> >>>>based modems.
> >>>>
> >>>>Regards,
> >>>>
> >>>>
> >>>>Antonio
> >>>>
> >>>>BTW,
> >>>>since you have experience with linux since the Red Hat days, did you
> >>>>get to use this particular modem before?  If you did and the drivers
> >>>>worked, I see no reason why the modem should not work with the newer
> >>>>kernels.
> >>>>
> >>>>
> >>>>On Tue, Jan 3, 2012 at 7:24 PM, Patrick Boyadjian
> >>>><patrick@xxxxxxxxxxxxxxxxxxxxxxx>   wrote:
> >>>>>Hi,
> >>>>>
> >>>>>This is my first attempt to contact this group so apologize in advance if I=  don't provide sufficient information.
> >>>>>
> >>>>>I'm not exactly a newbie to linux and Fedora since I've used it back when i= t was called red hat...I've upgraded to Fedora 16 recently and boy how thin= gs have changed!  Anyways, here is where I'm at:
> >>>>>
> >>>>>lspci shows my modem as:
> >>>>>01:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISD= N interface
> >>>>>
> >>>>>scanModem details as:
> >>>>>For candidate card in slot 01:01.0, firmware information and bootup diagnos= tics are:
> >>>>>PCI slot       PCI ID          SubsystemID     Name
> >>>>>----------     ---------       ---------       --------------
> >>>>>01:01.0        e159:0001       8086:0003       Communication controller: Ti=
> >>>>>ger Jet Network Inc. Tiger3XX Modem/ISDN interface
> >>>>>
> >>>>>Modem interrupt assignment and sharing:
> >>>>>--- Bootup diagnostics for card in PCI slot 01:01.0 ----
> >>>>>[    0.109098] pci 0000:01:01.0: [e159:0001] type 0 class 0x000780
> >>>>>[    0.109120] pci 0000:01:01.0: reg 10: [io  0xa000-0xa0ff]
> >>>>>[    0.109133] pci 0000:01:01.0: reg 14: [mem 0xf1004000-0xf1004fff]
> >>>>>[    0.109200] pci 0000:01:01.0: supports D2
> >>>>>[    0.109203] pci 0000:01:01.0: PME# supported from D0 D2 D3hot D3cold
> >>>>>[    0.109209] pci 0000:01:01.0: PME# disabled
> >>>>>
> >>>>>The PCI slot 01:01.0 of the modem card may be disabled early in a bootup process,  but then enabled later. If modem drivers load but the  modem is not responsive, read DOCs/Bootup.txt about possible fixes= .
> >>>>>Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx if help is needed.
> >>>>>
> >>>>>
> >>>>>
> >>>>>Predictive  diagnostics for card in bus 01:01.0:
> >>>>>        Modem chipset  detected on
> >>>>>NAME=3D"Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISD= N interface"
> >>>>>CLASS=3D0780
> >>>>>PCIDEV=3De159:0001
> >>>>>SUBSYS=3D8086:0003
> >>>>>IRQ=3D11
> >>>>>HDA2=3D00:1b.0
> >>>>>IDENT=3DINTEL537
> >>>>>
> >>>>>For candidate modem in:  01:01.0
> >>>>>   0780 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISD= N interface
> >>>>>      Primary device ID:  e159:0001
> >>>>>Support type needed or chipset:        INTEL537
> >>>>>
> >>>>>
> >>>>>So I visited http://vouters.dyndns.org/Intel/ and heeded Philippe's note to=
> >>>>>:
> >>>>>
> >>>>>
> >>>>>If you execute a 3.x.y kernel, download:
> >>>>>
> >>>>>../Intel/intel-536EP-537EP_2011_12_11.tar.bz2<http://vouters.dyndns.org/Int=
> >>>>>el/intel-536EP-537EP_2011_12_11.tar.bz2>
> >>>>>
> >>>>>
> >>>>>
> >>>>>...and continued to untar and try to build.
> >>>>>
> >>>>>Issuing make clean and make 537 seem to work with a warning:
> >>>>>
> >>>>>[root@pb3000 intel-536-537]# make clean
> >>>>>cd coredrv; make clean
> >>>>>make[1]: Entering directory `/root/intel-536-537/coredrv'
> >>>>>rm -f *.ko .*.o.cmd *.mod.c .*.ko.cmd *.o *~ core Module.* modules.* rm -rf .tmp_versions
> >>>>>make[1]: Leaving directory `/root/intel-536-537/coredrv'
> >>>>>rm -f *.o *.ko
> >>>>>[root@pb3000 intel-536-537]# make 537
> >>>>>cd coredrv; make clean
> >>>>>make[1]: Entering directory `/root/intel-536-537/coredrv'
> >>>>>rm -f *.ko .*.o.cmd *.mod.c .*.ko.cmd *.o *~ core Module.* modules.* rm -rf .tmp_versions
> >>>>>make[1]: Leaving directory `/root/intel-536-537/coredrv'
> >>>>>rm -f *.o *.ko
> >>>>>   Module precompile check
> >>>>>   Current running kernel is: 3.1.6-1.fc16.i686
> >>>>>   /lib/modules...   autoconf.h exists
> >>>>>diff: /boot/vmlinuz.autoconf.h: No such file or directory
> >>>>>   autoconf.h matches running kernel
> >>>>>diff: /boot/vmlinuz.version.h: No such file or directory
> >>>>>   version.h matches running kernel
> >>>>>make[1]: Entering directory `/root/intel-536-537'
> >>>>>Building for 537
> >>>>>3.1.6-1.fc16.i686
> >>>>>make[2]: Entering directory `/root/intel-536-537/coredrv'
> >>>>>make -C /lib/modules/3.1.6-1.fc16.i686/build M=3D/root/intel-536-537/coredr= v modules
> >>>>>make[3]: Entering directory `/usr/src/kernels/3.1.6-1.fc16.i686'
> >>>>>  CC [M]  /root/intel-536-537/coredrv/coredrv.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/clmmain.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/rts.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/task.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/uart.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/wwh_dflt.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/locks.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/softserial_io.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/softserial_ioctl.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/softserial.o
> >>>>>  CC [M]  /root/intel-536-537/coredrv/afedsp_int.o
> >>>>>  LD [M]  /root/intel-536-537/coredrv/Intel537.o
> >>>>>  Building modules, stage 2.
> >>>>>  MODPOST 1 modules
> >>>>>WARNING: could not find /root/intel-536-537/coredrv/.537core.lib.cmd for /r= oot/intel-536-537/coredrv/537core.lib
> >>>>>  CC      /root/intel-536-537/coredrv/Intel537.mod.o
> >>>>>  LD [M]  /root/intel-536-537/coredrv/Intel537.ko
> >>>>>make[3]: Leaving directory `/usr/src/kernels/3.1.6-1.fc16.i686'
> >>>>>make[2]: Leaving directory `/root/intel-536-537/coredrv'
> >>>>>make[1]: Leaving directory `/root/intel-536-537'
> >>>>>[root@pb3000 intel-536-537]#
> >>>>>
> >>>>>
> >>>>>However, make install fails complaining about kernel version:
> >>>>>
> >>>>>[root@pb3000 intel-536-537]# make install
> >>>>>make[1]: Entering directory `/root/intel-536-537'
> >>>>>rm -f /usr/sbin/hamregistry.bin
> >>>>>bash 537_inst
> >>>>>running kernel 3.1.6-1.fc16.i686
> >>>>>unsupported kernel version: only 2.4.x and 2.6.x are supported
> >>>>>make[1]: *** [install] Error 1
> >>>>>make[1]: Leaving directory `/root/intel-536-537'
> >>>>>[root@pb3000 intel-536-537]#
> >>>>>
> >>>>>
> >>>>>Am I missing something?  Any help here is super appreciated.
> >>>>>
> >>>>>Patrick
> >>>>>
> >>>>
> >>>
> >>
> >>--
> >>Philippe Vouters (Fontainebleau/France)
> >>URL: http://vouters.dyndns.org/
> >
> 
> -- 
> Philippe Vouters (Fontainebleau/France)
> URL: http://vouters.dyndns.org/


[Index of Archives]     [Linux Media Development]     [Asterisk]     [DCCP]     [Netdev]     [X.org]     [Xfree86]     [Fedora Women]     [Linux USB]

  Powered by Linux