Greg,
scanModem reports that you don't have a serial modem but a Conexant
Modem that needs separate drivers:
=== Finished firmware and bootup diagnostics, next deducing cogent
software. ===
Predictive diagnostics for card in bus 02:00.0:
Modem chipset detected on
NAME="Communication controller: Conexant Systems, Inc. Device 10b4 "
CLASS=0780
PCIDEV=14f1:10b4
SUBSYS=a0a0:010d
IRQ=11
IDENT=hcfpcimodem
For candidate modem in: 02:00.0
0780 Communication controller: Conexant Systems, Inc. Device 10b4
Primary device ID: 14f1:10b4
Support type needed or chipset: hcfpcimodem
For owners of a Dell PCs with Conexant HSF modems, a driver source
package with full speed enabled is available, but requires driver
compiling. Read DOCs/Conexant.txt
The modem requires a hcflinmodem package.
Modem support packages from Linuxant include resources for compiling
drivers.
If an installer package matching your kernel_version is not provided,
just install a generic code package.
From http://www.linuxant.com/drivers/hcf/full/downloads-ubuntu-x86.php
download
hcfpcimodem-7.80.02.05full_k2.6.38_10_generic_ubuntu_i386.deb.zip
Under Linux unpack with:
$ unzip hcfpcimodem*.zip
Then install with:
$ sudo dpkg -i hcfpcimodem*.deb
Subsequently, the modem should be found with
$ sudo wvdialconf /etc/wvdial.conf
Edit in your personal information with:
$ sudo gedit /etc/wvdial.conf
and try dialing out with:
$ sudo wvdial.
See DOCs/Testing.txt for details.
The directions following below need only be pursued, if the above
procedures are not adequate.
02:00.0
Read DOCs/Conexant.txt
You would need to download a generic package and compile it to get
14kbps if you want higher speed you need to contact Linuxant for a
license.
Regards,
Antonio
On Mon, Jul 18, 2011 at 6:32 PM, Greg Garowey <gfgarowey@xxxxxxxxxx> wrote:
> I have high-speed internet and only want to use the modem to fax.
>
> When using efax to fax PDF file i get the following messages
>
> efax-0.9a: 17:12:39 opened /dev/ttyS0
> efax-0.9a: 17:12:45 sync: dropping DTR
> efax-0.9a: 17:12:50 sync: sending escapes
> efax-0.9a: 17:12:55 Error: sync: no response from modem
>
> I am running:
>
> dell dimension 4550
>
> Intel P-4 2.53 GHz
>
> 1 gig ram
>
> ubuntu 11.04
>
> Kernel Linux 2.6.38-10-generic
>
> GNOME 2.32.1
>
>
> Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List
> Server,
> as HTML can contain viruses. Use as the email Subject Line:
> YourName, YourCountry kernel 2.6.38-10-generic
> With this Subject Line cogent experts will be alerted, and useful case
> names left in the Archive.
> YourCountry will enable Country specific guidance. Linux experts in
> YourCountry
> can be found through: http://www.linux.org/groups/index.html.
> They will know your Country's modem code, which may be essential for
> dialup service.
> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an
> Internet Provider mail filters.
> So in a day, also check the Archived responses at
> http://www.linmodems.org
> -------------------------- System information
> ----------------------------
> CPU=i686, Ubuntu , ALSA_version=1.0.23
> Linux version 2.6.38-10-generic (buildd@vernadsky) (gcc version 4.5.2
> (Ubuntu/Linaro 4.5.2-8ubuntu4) ) #46-Ubuntu SMP Tue Jun 28 15:05:41 UTC
> 2011
> scanModem update of: 2011_02_04
>
> Distrib_ID=Ubuntu
> DistribCodeName=natty
> AptRepositoryStem=http://ca.archive.ubuntu.com/ubuntu/
>
>
> Presently install your Linux Distributions dkms package. It provides for
> automated driver updates,
> following upgrade of your kernel. For details see
> http://linux.dell.com/projects.shtml#dkms
>
> There are no blacklisted modem drivers in /etc/modprobe* files
>
> Potentially useful modem drivers now loaded are:
>
>
> Attached USB devices are:
> ID 05fd:3000 InterAct, Inc.
> ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1
> ID 090c:a370 Feiya Technology Corp.
> If a cellphone is not detected, see
> http://ubuntuforums.org/archive/index.php/t-878554.html
> A sample report is:
> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
>
> If a USB modem or cellphone is attached and was not detected, please
> provide available information in your request to discuss@xxxxxxxxxxxxx
>
> Candidate PCI devices with modem chips are:
> 02:00.0 Communication controller: Conexant Systems, Inc. Device 10b4
> (rev 89)
> High Definition Audio cards can host modem chips.
>
> For candidate card in slot 02:00.0, firmware information and bootup
> diagnostics are:
> PCI slot PCI ID SubsystemID Name
> ---------- --------- --------- --------------
> 02:00.0 14f1:10b4 a0a0:010d Communication controller: Conexant Systems,
> Inc. Device 10b4
>
> Modem interrupt assignment and sharing:
> --- Bootup diagnostics for card in PCI slot 02:00.0 ----
> [ 0.161772] pci 0000:02:00.0: [14f1:10b4] type 0 class 0x000780
> [ 0.161791] pci 0000:02:00.0: reg 10: [mem 0xfe1f0000-0xfe1fffff]
> [ 0.161802] pci 0000:02:00.0: reg 14: [io 0xecf8-0xecff]
> [ 0.161859] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
> [ 0.161865] pci 0000:02:00.0: PME# disabled
>
> The PCI slot 02:00.0 of the modem card may be disabled early in
> a bootup process, but then enabled later. If modem drivers load
> but the modem is not responsive, read DOCs/Bootup.txt about possible
> fixes.
> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
> if help is needed.
>
>
> === Finished firmware and bootup diagnostics, next deducing cogent
> software. ===
>
> Predictive diagnostics for card in bus 02:00.0:
> Modem chipset detected on
> NAME="Communication controller: Conexant Systems, Inc. Device 10b4 "
> CLASS=0780
> PCIDEV=14f1:10b4
> SUBSYS=a0a0:010d
> IRQ=11
> IDENT=hcfpcimodem
>
> For candidate modem in: 02:00.0
> 0780 Communication controller: Conexant Systems, Inc. Device 10b4
> Primary device ID: 14f1:10b4
> Support type needed or chipset: hcfpcimodem
>
>
>
> For owners of a Dell PCs with Conexant HSF modems, a driver source
> package with full speed enabled is available, but requires driver
> compiling. Read DOCs/Conexant.txt
>
> The modem requires a hcflinmodem package.
>
> Modem support packages from Linuxant include resources for compiling
> drivers.
> If an installer package matching your kernel_version is not provided,
> just install a generic code package.
>
> From http://www.linuxant.com/drivers/hcf/full/downloads-ubuntu-x86.php
> download
> hcfpcimodem-7.80.02.05full_k2.6.38_10_generic_ubuntu_i386.deb.zip
> Under Linux unpack with:
> $ unzip hcfpcimodem*.zip
> Then install with:
> $ sudo dpkg -i hcfpcimodem*.deb
> Subsequently, the modem should be found with
> $ sudo wvdialconf /etc/wvdial.conf
> Edit in your personal information with:
> $ sudo gedit /etc/wvdial.conf
> and try dialing out with:
> $ sudo wvdial.
> See DOCs/Testing.txt for details.
>
> The directions following below need only be pursued, if the above
> procedures are not adequate.
> 02:00.0
> Read DOCs/Conexant.txt
>
> Writing DOCs/Conexant.txt
>
>
> Completed candidate modem analyses.
>
> The base of the UDEV device file system is: /dev/.udev
>
> Versions adequately match for the compiler installed: 4.5.2
> and the compiler used in kernel assembly: 4.5.2
>
> linux-headers-2.6.38-10-generic resources needed for compiling are not
> manifestly ready!
>
> If compiling is necessary packages must be installed, providing:
> linux-headers-2.6.38-10-generic
>
>
> If a driver compilation fails, with message including some lack of some
> FileName.h (stdio.h for example), then
> Some additional kernel-header files need installation to /usr/include.
> The minimal additional packages are libc6-dev
> and any of its dependents, under Ubuntu linux-libc-dev
>
> If an alternate ethernet connection is available,
> $ apt-get update
> $ apt-get -s install linux-kernel-devel
> will install needed packages.
> For Debian/Ubuntu related distributions, run the following command to
> display the needed package list:
>
> Otherwise packages have to be found through http://packages.ubuntu.com
> Once downloaded and transferred into a Linux partition,
> they can be installed alltogether with:
> $ sudo dpkg -i *.deb
>
>
> Checking pppd properties:
> -rwsr-xr-- 1 root dip 273272 2011-02-04 00:43 /usr/sbin/pppd
>
> In case of an "error 17" "serial loopback" problem, see:
>
> http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
>
> To enable dialout without Root permission do:
> $ su - root (not for Ubuntu)
> sudo chmod a+x /usr/sbin/pppd
> or under Ubuntu related Linuxes
> sudo chmod a+x /usr/sbin/pppd
>
> Checking settings of: /etc/ppp/options
> asyncmap 0
> noauth
> crtscts
> lock
> hide-password
> modem
> lcp-echo-interval 30
> lcp-echo-failure 4
> noipx
>
> In case of a message like:
> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
> see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
>
> For guidance on FAX usage, get from
> http://linmodems.technion.ac.il/packages/ get faxing.tar.gz
> It has samples for a modem using port /dev/ttySL0, which must be changed
> to match your modem's port.
>
> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0
> wlan0
> Which can interfere with Browser naviagation.
>
> Don't worry about the following, it is for experts should trouble
> shooting be necessary.
> ==========================================================
>
> Checking for modem support lines:
> --------------------------------------
> /device/modem symbolic link:
> slmodemd created symbolic link /dev/ttySL0:
> Within /etc/udev/ files:
>
> Within /etc/modprobe.conf files:
> /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in order
> to blacklist unwanted modem drivers
> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
> /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
> /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
> Within any ancient /etc/devfs files:
>
> Within ancient kernel 2.4.n /etc/module.conf files:
>
> --------- end modem support lines --------
>
> CPU0
> 0: 50 IO-APIC-edge timer
> 1: 2 IO-APIC-edge i8042
> 6: 3 IO-APIC-edge floppy
> 7: 0 IO-APIC-edge parport0
> 8: 0 IO-APIC-edge rtc0
> 9: 0 IO-APIC-fasteoi acpi
> 12: 4 IO-APIC-edge i8042
> 14: 6921 IO-APIC-edge ata_piix
> 15: 534 IO-APIC-edge ata_piix
> 16: 2948 IO-APIC-fasteoi uhci_hcd:usb2, nouveau
> 17: 33 IO-APIC-fasteoi 0000:02:0c.0
> 18: 655 IO-APIC-fasteoi uhci_hcd:usb4, EMU10K1X
> 19: 0 IO-APIC-fasteoi uhci_hcd:usb3
> 20: 186 IO-APIC-fasteoi eth0
> 23: 26 IO-APIC-fasteoi ehci_hcd:usb1
> NMI: 0 Non-maskable interrupts
> LOC: 16941 Local timer interrupts
> SPU: 0 Spurious interrupts
> PMI: 0 Performance monitoring interrupts
> IWI: 0 IRQ work interrupts
> RES: 0 Rescheduling interrupts
> CAL: 0 Function call interrupts
> TLB: 0 TLB shootdowns
> TRM: 0 Thermal event interrupts
> THR: 0 Threshold APIC interrupts
> MCE: 0 Machine check exceptions
> MCP: 1 Machine check polls
> ERR: 0
> MIS: 0
>
> [ 0.000000] Initializing cgroup subsys cpuset
> [ 0.000000] Initializing cgroup subsys cpu
> [ 0.000000] Linux version 2.6.38-10-generic (buildd@vernadsky) (gcc
> version 4.5.2 (Ubuntu/Linaro 4.5.2-8ubuntu4) ) #46-Ubuntu SMP Tue Jun 28
> 15:05:41 UTC 2011 (Ubuntu 2.6.38-10.46-generic 2.6.38.7)
> [ 0.000000] BIOS-provided physical RAM map:
> [ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
> [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000
> (reserved)
> [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ff75000 (usable)
> [ 0.000000] BIOS-e820: 000000003ff75000 - 000000003ff77000 (ACPI
> NVS)
> [ 0.000000] BIOS-e820: 000000003ff77000 - 000000003ff98000 (ACPI
> data)
> [ 0.000000] BIOS-e820: 000000003ff98000 - 0000000040000000
> (reserved)
> [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000
> (reserved)
> [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000
> (reserved)
> [ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000
> (reserved)
> [ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
> [ 0.000000] NX (Execute Disable) protection: approximated by x86
> segment limits
> [ 0.000000] DMI 2.3 present.
> [ 0.000000] DMI: Dell Computer Corporation Dimension
> 4550 /0M0321, BIOS A05 01/27/2003
> [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000
> (usable) ==> (reserved)
> [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000
> (usable)
> [ 0.000000] last_pfn = 0x3ff75 max_arch_pfn = 0x100000
> [ 0.000000] MTRR default type: uncachable
> [ 0.000000] MTRR fixed ranges enabled:
> [ 0.000000] 00000-9FFFF write-back
> [ 0.000000] A0000-BFFFF uncachable
> [ 0.000000] C0000-D3FFF write-protect
> [ 0.000000] D4000-EFFFF uncachable
> [ 0.000000] F0000-FFFFF write-protect
> [ 0.000000] MTRR variable ranges enabled:
> [ 0.000000] 0 base 000000000 mask FC0000000 write-back
> [ 0.000000] 1 disabled
> [ 0.000000] 2 disabled
> [ 0.000000] 3 disabled
> [ 0.000000] 4 disabled
> [ 0.000000] 5 disabled
> [ 0.000000] 6 disabled
> [ 0.000000] 7 disabled
> [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
> 0x7010600070106
> [ 0.000000] found SMP MP-table at [c00fe710] fe710
> [ 0.000000] initial memory mapped : 0 - 01c00000
> [ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
> [ 0.000000] 0000000000 - 0000400000 page 4k
> [ 0.000000] 0000400000 - 0037400000 page 2M
> [ 0.000000] 0037400000 - 00377fe000 page 4k
> [ 0.000000] kernel direct mapping tables up to 377fe000 @
> 1bfb000-1c00000
> [ 0.000000] RAMDISK: 36768000 - 373ac000
> [ 0.000000] ACPI: RSDP 000feb90 00014 (v00 DELL )
> [ 0.000000] ACPI: RSDT 000fd4f9 00038 (v01 DELL 4550 00000008
> ASL 00000061)
> [ 0.000000] ACPI: FACP 000fd531 00074 (v01 DELL 4550 00000008
> ASL 00000061)
> [ 0.000000] ACPI: DSDT fffce938 022EA (v01 DELL dt_ex 00001000
> MSFT 0100000D)
> [ 0.000000] ACPI: FACS 3ff75000 00040
> [ 0.000000] ACPI: SSDT fffd0d5f 000BA (v01 DELL st_ex 00001000
> MSFT 0100000D)
> [ 0.000000] ACPI: APIC 000fd5a5 0006C (v01 DELL 4550 00000008
> ASL 00000061)
> [ 0.000000] ACPI: BOOT 000fd611 00028 (v01 DELL 4550 00000008
> ASL 00000061)
> [ 0.000000] ACPI: ASF! 000fd639 00067 (v16 DELL 4550 00000008
> ASL 00000061)
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] 135MB HIGHMEM available.
> [ 0.000000] 887MB LOWMEM available.
> [ 0.000000] mapped low ram: 0 - 377fe000
> [ 0.000000] low ram: 0 - 377fe000
> [ 0.000000] Zone PFN ranges:
> [ 0.000000] DMA 0x00000010 -> 0x00001000
> [ 0.000000] Normal 0x00001000 -> 0x000377fe
> [ 0.000000] HighMem 0x000377fe -> 0x0003ff75
> [ 0.000000] Movable zone start PFN for each node
> [ 0.000000] early_node_map[2] active PFN ranges
> [ 0.000000] 0: 0x00000010 -> 0x000000a0
> [ 0.000000] 0: 0x00000100 -> 0x0003ff75
> [ 0.000000] On node 0 totalpages: 261893
> [ 0.000000] free_area_init_node: node 0, pgdat c1784140, node_mem_map
> f5f68200
> [ 0.000000] DMA zone: 32 pages used for memmap
> [ 0.000000] DMA zone: 0 pages reserved
> [ 0.000000] DMA zone: 3952 pages, LIFO batch:0
> [ 0.000000] Normal zone: 1744 pages used for memmap
> [ 0.000000] Normal zone: 221486 pages, LIFO batch:31
> [ 0.000000] HighMem zone: 271 pages used for memmap
> [ 0.000000] HighMem zone: 34408 pages, LIFO batch:7
> [ 0.000000] Using APIC driver default
> [ 0.000000] ACPI: PM-Timer IO Port: 0x808
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
> [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
> [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI
> 0-23
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high
> level)
> [ 0.000000] ACPI: IRQ0 used by override.
> [ 0.000000] ACPI: IRQ2 used by override.
> [ 0.000000] ACPI: IRQ9 used by override.
> [ 0.000000] Using ACPI (MADT) for SMP configuration information
> [ 0.000000] SMP: Allowing 4 CPUs, 3 hotplug CPUs
> [ 0.000000] nr_irqs_gsi: 40
> [ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
> 00000000000f0000
> [ 0.000000] PM: Registered nosave memory: 00000000000f0000 -
> 0000000000100000
> [ 0.000000] Allocating PCI resources starting at 40000000 (gap:
> 40000000:bec00000)
> [ 0.000000] Booting paravirtualized kernel on bare hardware
> [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4
> nr_node_ids:1
> [ 0.000000] PERCPU: Embedded 13 pages/cpu @f5800000 s28800 r0 d24448
> u1048576
> [ 0.000000] pcpu-alloc: s28800 r0 d24448 u1048576 alloc=1*4194304
> [ 0.000000] pcpu-alloc: [0] 0 1 2 3
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
> Total pages: 259846
> [ 0.000000] Kernel command line:
> BOOT_IMAGE=/boot/vmlinuz-2.6.38-10-generic
> root=UUID=b01cc50d-fbe2-4537-bea9-1acf9852aa97 ro quiet splash
> vt.handoff=7
> [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
> [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288
> bytes)
> [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
> bytes)
> [ 0.000000] Initializing CPU#0
> [ 0.000000] allocated 5239780 bytes of page_cgroup
> [ 0.000000] please try 'cgroup_disable=memory' option if you don't
> want memory cgroups
> [ 0.000000] Initializing HighMem for node 0 (000377fe:0003ff75)
> [ 0.000000] Memory: 1011296k/1048020k available (5190k kernel code,
> 36276k reserved, 2539k data, 700k init, 138716k highmem)
> [ 0.000000] virtual kernel memory layout:
> [ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
> [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> [ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
> [ 0.000000] .init : 0xc178d000 - 0xc183c000 ( 700 kB)
> [ 0.000000] .data : 0xc1511841 - 0xc178c4c0 (2539 kB)
> [ 0.000000] .text : 0xc1000000 - 0xc1511841 (5190 kB)
> [ 0.000000] Checking if this processor honours the WP bit even in
> supervisor mode...Ok.
> [ 0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0,
> CPUs=4, Nodes=1
> [ 0.000000] Hierarchical RCU implementation.
> [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
> [ 0.000000] RCU-based detection of stalled CPUs is disabled.
> [ 0.000000] NR_IRQS:2304 nr_irqs:712 16
> [ 0.000000] CPU 0 irqstacks, hard=f4c08000 soft=f4c0a000
> [ 0.000000] vt handoff: transparent VT on vt#7
> [ 0.000000] Console: colour dummy device 80x25
> [ 0.000000] console [tty0] enabled
> [ 0.000000] Fast TSC calibration using PIT
> [ 0.000000] Detected 2524.885 MHz processor.
> [ 0.008006] Calibrating delay loop (skipped), value calculated using
> timer frequency.. 5049.77 BogoMIPS (lpj=10099540)
> [ 0.008015] pid_max: default: 32768 minimum: 301
> [ 0.008055] Security Framework initialized
> [ 0.008086] AppArmor: AppArmor initialized
> [ 0.008090] Yama: becoming mindful.
> [ 0.008189] Mount-cache hash table entries: 512
> [ 0.008450] Initializing cgroup subsys ns
> [ 0.008457] ns_cgroup deprecated: consider using the 'clone_children'
> flag without the ns_cgroup.
> [ 0.008463] Initializing cgroup subsys cpuacct
> [ 0.008471] Initializing cgroup subsys memory
> [ 0.008487] Initializing cgroup subsys devices
> [ 0.008492] Initializing cgroup subsys freezer
> [ 0.008496] Initializing cgroup subsys net_cls
> [ 0.008500] Initializing cgroup subsys blkio
> [ 0.008565] CPU0: Hyper-Threading is disabled
> [ 0.008570] mce: CPU supports 4 MCE banks
> [ 0.008586] CPU0: Thermal monitoring enabled (TM1)
> [ 0.009419] SMP alternatives: switching to UP code
> [ 0.022989] ACPI: Core revision 20110112
> [ 0.047320] ftrace: allocating 23648 entries in 47 pages
> [ 0.048131] Enabling APIC mode: Flat. Using 1 I/O APICs
> [ 0.048431] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> [ 0.090179] CPU0: Intel(R) Pentium(R) 4 CPU 2.53GHz stepping 07
> [ 0.092004] Performance Events: Netburst events, Netburst P4/Xeon PMU
> driver.
> [ 0.092004] ... version: 0
> [ 0.092004] ... bit width: 40
> [ 0.092004] ... generic registers: 18
> [ 0.092004] ... value mask: 000000ffffffffff
> [ 0.092004] ... max period: 0000007fffffffff
> [ 0.092004] ... fixed-purpose events: 0
> [ 0.092004] ... event mask: 000000000003ffff
> [ 0.092004] Brought up 1 CPUs
> [ 0.092004] Total of 1 processors activated (5049.77 BogoMIPS).
> [ 0.092004] devtmpfs: initialized
> [ 0.092004] print_constraints: dummy:
> [ 0.092004] Time: 22:49:00 Date: 07/18/11
> [ 0.092004] NET: Registered protocol family 16
> [ 0.092004] EISA bus registered
> [ 0.092004] ACPI: bus type pci registered
> [ 0.117758] PCI: PCI BIOS revision 2.10 entry at 0xfbe70, last bus=2
> [ 0.117761] PCI: Using configuration type 1 for base access
> [ 0.119496] bio: create slab <bio-0> at 0
> [ 0.120297] ACPI: EC: Look up EC in DSDT
> [ 0.137229] ACPI: Interpreter enabled
> [ 0.137241] ACPI: (supports S0 S1 S3 S4 S5)
> [ 0.137280] ACPI: Using IOAPIC for interrupt routing
> [ 0.160516] ACPI: No dock devices found.
> [ 0.160520] HEST: Table not found.
> [ 0.160527] PCI: Ignoring host bridge windows from ACPI; if
> necessary, use "pci=use_crs" and report a bug
> [ 0.160557] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
> [ 0.160630] pci_root PNP0A03:00: host bridge window [io
> 0x0000-0x0cf7] (ignored)
> [ 0.160635] pci_root PNP0A03:00: host bridge window [io
> 0x0d00-0xffff] (ignored)
> [ 0.160639] pci_root PNP0A03:00: host bridge window [mem
> 0x000a0000-0x000bffff] (ignored)
> [ 0.160644] pci_root PNP0A03:00: host bridge window [mem
> 0x000c8000-0x000dffff] (ignored)
> [ 0.160648] pci_root PNP0A03:00: host bridge window [mem
> 0xc0000000-0xfebfffff] (ignored)
> [ 0.160652] pci_root PNP0A03:00: host bridge window [mem
> 0xfef00000-0xffafffff] (ignored)
> [ 0.160673] pci 0000:00:00.0: [8086:2560] type 0 class 0x000600
> [ 0.160685] pci 0000:00:00.0: reg 10: [mem 0xe8000000-0xefffffff
> pref]
> [ 0.160755] pci 0000:00:01.0: [8086:2561] type 1 class 0x000604
> [ 0.160830] pci 0000:00:1d.0: [8086:24c2] type 0 class 0x000c03
> [ 0.160880] pci 0000:00:1d.0: reg 20: [io 0xff80-0xff9f]
> [ 0.160919] pci 0000:00:1d.1: [8086:24c4] type 0 class 0x000c03
> [ 0.160968] pci 0000:00:1d.1: reg 20: [io 0xff60-0xff7f]
> [ 0.161007] pci 0000:00:1d.2: [8086:24c7] type 0 class 0x000c03
> [ 0.161056] pci 0000:00:1d.2: reg 20: [io 0xff40-0xff5f]
> [ 0.161106] pci 0000:00:1d.7: [8086:24cd] type 0 class 0x000c03
> [ 0.161131] pci 0000:00:1d.7: reg 10: [mem 0xfe300000-0xfe3003ff]
> [ 0.161217] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
> [ 0.161224] pci 0000:00:1d.7: PME# disabled
> [ 0.161244] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
> [ 0.161293] pci 0000:00:1f.0: [8086:24c0] type 0 class 0x000601
> [ 0.161298] * The chipset may have PM-Timer Bug. Due to workarounds
> for a bug,
> [ 0.161301] * this clock source is slow. If you are sure your timer
> does not have
> [ 0.161303] * this bug, please use "acpi_pm_good" to disable the
> workaround
> [ 0.161390] pci 0000:00:1f.1: [8086:24cb] type 0 class 0x000101
> [ 0.161407] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
> [ 0.161419] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
> [ 0.161431] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
> [ 0.161442] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
> [ 0.161454] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf]
> [ 0.161466] pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
> [ 0.161499] pci 0000:00:1f.3: [8086:24c3] type 0 class 0x000c05
> [ 0.161548] pci 0000:00:1f.3: reg 20: [io 0xdc80-0xdc9f]
> [ 0.161604] pci 0000:01:00.0: [10de:0172] type 0 class 0x000300
> [ 0.161622] pci 0000:01:00.0: reg 10: [mem 0xfc000000-0xfcffffff]
> [ 0.161632] pci 0000:01:00.0: reg 14: [mem 0xf4000000-0xf7ffffff
> pref]
> [ 0.161642] pci 0000:01:00.0: reg 18: [mem 0xf3f80000-0xf3ffffff
> pref]
> [ 0.161669] pci 0000:01:00.0: reg 30: [mem 0x80000000-0x8001ffff
> pref]
> [ 0.161726] pci 0000:00:01.0: PCI bridge to [bus 01-01]
> [ 0.161732] pci 0000:00:01.0: bridge window [io 0xf000-0x0000]
> (disabled)
> [ 0.161738] pci 0000:00:01.0: bridge window [mem
> 0xfc000000-0xfdffffff]
> [ 0.161744] pci 0000:00:01.0: bridge window [mem
> 0xf0000000-0xf7ffffff pref]
> [ 0.161772] pci 0000:02:00.0: [14f1:10b4] type 0 class 0x000780
> [ 0.161791] pci 0000:02:00.0: reg 10: [mem 0xfe1f0000-0xfe1fffff]
> [ 0.161802] pci 0000:02:00.0: reg 14: [io 0xecf8-0xecff]
> [ 0.161859] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
> [ 0.161865] pci 0000:02:00.0: PME# disabled
> [ 0.161886] pci 0000:02:02.0: [1102:0006] type 0 class 0x000401
> [ 0.161905] pci 0000:02:02.0: reg 10: [io 0xecc0-0xecdf]
> [ 0.161970] pci 0000:02:02.0: supports D1 D2
> [ 0.161995] pci 0000:02:02.1: [1102:7004] type 0 class 0x000980
> [ 0.162012] pci 0000:02:02.1: reg 10: [io 0xecf0-0xecf7]
> [ 0.162078] pci 0000:02:02.1: supports D1 D2
> [ 0.162111] pci 0000:02:08.0: [8086:1039] type 0 class 0x000200
> [ 0.162130] pci 0000:02:08.0: reg 10: [mem 0xfe1ef000-0xfe1effff]
> [ 0.162141] pci 0000:02:08.0: reg 14: [io 0xec80-0xecbf]
> [ 0.162198] pci 0000:02:08.0: supports D1 D2
> [ 0.162201] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot
> D3cold
> [ 0.162207] pci 0000:02:08.0: PME# disabled
> [ 0.162231] pci 0000:02:0c.0: [1814:0301] type 0 class 0x000280
> [ 0.162250] pci 0000:02:0c.0: reg 10: [mem 0xfe1e0000-0xfe1e7fff]
> [ 0.162347] pci 0000:00:1e.0: PCI bridge to [bus 02-02] (subtractive
> decode)
> [ 0.162353] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
> [ 0.162360] pci 0000:00:1e.0: bridge window [mem
> 0xfe100000-0xfe2fffff]
> [ 0.162366] pci 0000:00:1e.0: bridge window [mem
> 0xfff00000-0x000fffff pref] (disabled)
> [ 0.162371] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff]
> (subtractive decode)
> [ 0.162375] pci 0000:00:1e.0: bridge window [mem
> 0x00000000-0xffffffff] (subtractive decode)
> [ 0.162390] pci_bus 0000:00: on NUMA node 0
> [ 0.162395] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> [ 0.162771] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
> [ 0.188347] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11
> 12 15)
> [ 0.188690] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11
> 12 15)
> [ 0.189028] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11
> 12 15)
> [ 0.189367] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11
> 12 15)
> [ 0.189704] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11
> 12 15)
> [ 0.190042] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11
> 12 15)
> [ 0.190377] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11
> 12 15) *0, disabled.
> [ 0.190716] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11
> 12 15)
> [ 0.190951] vgaarb: device added: PCI:0000:01:00.0,decodes=io
> +mem,owns=io+mem,locks=none
> [ 0.190959] vgaarb: loaded
> [ 0.191336] SCSI subsystem initialized
> [ 0.191439] libata version 3.00 loaded.
> [ 0.191527] usbcore: registered new interface driver usbfs
> [ 0.191547] usbcore: registered new interface driver hub
> [ 0.191588] usbcore: registered new device driver usb
> [ 0.191769] wmi: Mapper loaded
> [ 0.191772] PCI: Using ACPI for IRQ routing
> [ 0.191778] PCI: pci_cache_line_size set to 64 bytes
> [ 0.191854] reserve RAM buffer: 000000003ff75000 - 000000003fffffff
> [ 0.192038] NetLabel: Initializing
> [ 0.192042] NetLabel: domain hash size = 128
> [ 0.192045] NetLabel: protocols = UNLABELED CIPSOv4
> [ 0.192061] NetLabel: unlabeled traffic allowed by default
> [ 0.203282] AppArmor: AppArmor Filesystem Enabled
> [ 0.203342] pnp: PnP ACPI init
> [ 0.203375] ACPI: bus type pnp registered
> [ 0.206862] pnp 00:00: [mem 0x00000000-0x0009ffff]
> [ 0.206866] pnp 00:00: [mem 0x00100000-0x00ffffff]
> [ 0.206870] pnp 00:00: [mem 0x01000000-0x3ff74fff]
> [ 0.206874] pnp 00:00: [mem 0x000f0000-0x000fffff]
> [ 0.206877] pnp 00:00: [mem 0xfec00000-0xfec0ffff]
> [ 0.206881] pnp 00:00: [mem 0xfee00000-0xfee0ffff]
> [ 0.206885] pnp 00:00: [mem 0xffb00000-0xffbfffff]
> [ 0.206888] pnp 00:00: [mem 0xffc00000-0xffffffff]
> [ 0.206972] system 00:00: [mem 0x00000000-0x0009ffff] could not be
> reserved
> [ 0.206978] system 00:00: [mem 0x00100000-0x00ffffff] could not be
> reserved
> [ 0.206982] system 00:00: [mem 0x01000000-0x3ff74fff] could not be
> reserved
> [ 0.206987] system 00:00: [mem 0x000f0000-0x000fffff] could not be
> reserved
> [ 0.206991] system 00:00: [mem 0xfec00000-0xfec0ffff] could not be
> reserved
> [ 0.206996] system 00:00: [mem 0xfee00000-0xfee0ffff] has been
> reserved
> [ 0.207000] system 00:00: [mem 0xffb00000-0xffbfffff] has been
> reserved
> [ 0.207005] system 00:00: [mem 0xffc00000-0xffffffff] has been
> reserved
> [ 0.207012] system 00:00: Plug and Play ACPI device, IDs PNP0c01
> (active)
> [ 0.207041] pnp 00:01: [bus 00-ff]
> [ 0.207045] pnp 00:01: [io 0x0cf8-0x0cff]
> [ 0.207049] pnp 00:01: [io 0x0000-0x0cf7 window]
> [ 0.207052] pnp 00:01: [io 0x0d00-0xffff window]
> [ 0.207056] pnp 00:01: [mem 0x000a0000-0x000bffff window]
> [ 0.207060] pnp 00:01: [mem 0x000c8000-0x000dffff window]
> [ 0.207064] pnp 00:01: [mem 0xc0000000-0xfebfffff window]
> [ 0.207068] pnp 00:01: [mem 0xfef00000-0xffafffff window]
> [ 0.207122] pnp 00:01: Plug and Play ACPI device, IDs PNP0a03
> (active)
> [ 0.209590] pnp 00:02: [io 0x0080-0x009f]
> [ 0.209594] pnp 00:02: [io 0x0000-0x001f]
> [ 0.209597] pnp 00:02: [io 0x00c0-0x00df]
> [ 0.209601] pnp 00:02: [dma 4]
> [ 0.209642] pnp 00:02: Plug and Play ACPI device, IDs PNP0200
> (active)
> [ 0.209741] pnp 00:03: [io 0x00f0-0x00ff]
> [ 0.209761] pnp 00:03: [irq 13]
> [ 0.209806] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04
> (active)
> [ 0.209903] pnp 00:04: [io 0x0061]
> [ 0.209942] pnp 00:04: Plug and Play ACPI device, IDs PNP0800
> (active)
> [ 0.210045] pnp 00:05: [io 0x0070-0x007f]
> [ 0.210053] pnp 00:05: [irq 8]
> [ 0.210098] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00
> (active)
> [ 0.213038] pnp 00:06: [io 0x03f0-0x03f5]
> [ 0.213043] pnp 00:06: [io 0x03f7]
> [ 0.213051] pnp 00:06: [irq 6]
> [ 0.213055] pnp 00:06: [dma 2]
> [ 0.213311] pnp 00:06: Plug and Play ACPI device, IDs PNP0700
> (active)
> [ 0.217884] pnp 00:07: [io 0x03f8-0x03ff]
> [ 0.217892] pnp 00:07: [irq 4]
> [ 0.218104] pnp 00:07: Plug and Play ACPI device, IDs PNP0501
> (active)
> [ 0.221438] pnp 00:08: [io 0x0378-0x037f]
> [ 0.221442] pnp 00:08: [io 0x0778-0x077f]
> [ 0.221449] pnp 00:08: [irq 7]
> [ 0.221452] pnp 00:08: [dma 0 disabled]
> [ 0.221980] pnp 00:08: Plug and Play ACPI device, IDs PNP0401
> (active)
> [ 0.223655] pnp 00:09: [io 0x0060]
> [ 0.223659] pnp 00:09: [io 0x0064]
> [ 0.223663] pnp 00:09: [io 0x0062-0x0063]
> [ 0.223670] pnp 00:09: [io 0x0065-0x006f]
> [ 0.223673] pnp 00:09: [io 0x00e0-0x00ef]
> [ 0.223677] pnp 00:09: [io 0x0800-0x085f]
> [ 0.223680] pnp 00:09: [io 0x0c00-0x0c7f]
> [ 0.223683] pnp 00:09: [io 0x0860-0x08ff]
> [ 0.223752] system 00:09: [io 0x0800-0x085f] has been reserved
> [ 0.223757] system 00:09: [io 0x0c00-0x0c7f] has been reserved
> [ 0.223761] system 00:09: [io 0x0860-0x08ff] has been reserved
> [ 0.223767] system 00:09: Plug and Play ACPI device, IDs PNP0c01
> (active)
> [ 0.224507] pnp: PnP ACPI: found 10 devices
> [ 0.224511] ACPI: ACPI bus type pnp unregistered
> [ 0.224517] PnPBIOS: Disabled by ACPI PNP
> [ 0.261996] Switching to clocksource acpi_pm
> [ 0.262028] pci 0000:01:00.0: no compatible bridge window for [mem
> 0x80000000-0x8001ffff pref]
> [ 0.262061] pci 0000:00:1f.1: BAR 5: assigned [mem
> 0x40000000-0x400003ff]
> [ 0.262070] pci 0000:00:1f.1: BAR 5: set to [mem
> 0x40000000-0x400003ff] (PCI address [0x40000000-0x400003ff])
> [ 0.262076] pci 0000:01:00.0: BAR 6: assigned [mem
> 0xf0000000-0xf001ffff pref]
> [ 0.262081] pci 0000:00:01.0: PCI bridge to [bus 01-01]
> [ 0.262085] pci 0000:00:01.0: bridge window [io disabled]
> [ 0.262092] pci 0000:00:01.0: bridge window [mem
> 0xfc000000-0xfdffffff]
> [ 0.262098] pci 0000:00:01.0: bridge window [mem
> 0xf0000000-0xf7ffffff pref]
> [ 0.262107] pci 0000:00:1e.0: PCI bridge to [bus 02-02]
> [ 0.262112] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
> [ 0.262119] pci 0000:00:1e.0: bridge window [mem
> 0xfe100000-0xfe2fffff]
> [ 0.262125] pci 0000:00:1e.0: bridge window [mem pref disabled]
> [ 0.262147] pci 0000:00:1e.0: setting latency timer to 64
> [ 0.262153] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
> [ 0.262157] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
> [ 0.262162] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfdffffff]
> [ 0.262166] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff
> pref]
> [ 0.262170] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
> [ 0.262174] pci_bus 0000:02: resource 1 [mem 0xfe100000-0xfe2fffff]
> [ 0.262178] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
> [ 0.262182] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff]
> [ 0.262246] NET: Registered protocol family 2
> [ 0.262350] IP route cache hash table entries: 32768 (order: 5,
> 131072 bytes)
> [ 0.262789] TCP established hash table entries: 131072 (order: 8,
> 1048576 bytes)
> [ 0.263947] TCP bind hash table entries: 65536 (order: 7, 524288
> bytes)
> [ 0.263947] Switched to NOHz mode on CPU #0
> [ 0.263947] TCP: Hash tables configured (established 131072 bind
> 65536)
> [ 0.263947] TCP reno registered
> [ 0.263947] UDP hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.263947] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.263947] NET: Registered protocol family 1
> [ 0.263947] pci 0000:01:00.0: Boot video device
> [ 0.263947] pci 0000:02:08.0: Firmware left e100 interrupts enabled;
> disabling
> [ 0.263947] PCI: CLS 64 bytes, default 64
> [ 0.263947] Simple Boot Flag value 0x87 read from CMOS RAM was
> invalid
> [ 0.263947] Simple Boot Flag at 0x7a set to 0x1
> [ 0.263947] cpufreq-nforce2: No nForce2 chipset.
> [ 0.263961] audit: initializing netlink socket (disabled)
> [ 0.263980] type=2000 audit(1311029339.260:1): initialized
> [ 0.274830] Trying to unpack rootfs image as initramfs...
> [ 0.292400] highmem bounce pool size: 64 pages
> [ 0.292412] HugeTLB registered 4 MB page size, pre-allocated 0 pages
> [ 0.300524] VFS: Disk quotas dquot_6.5.2
> [ 0.300629] Dquot-cache hash table entries: 1024 (order 0, 4096
> bytes)
> [ 0.301735] fuse init (API version 7.16)
> [ 0.301888] msgmni has been set to 1704
> [ 0.308740] Block layer SCSI generic (bsg) driver version 0.4 loaded
> (major 253)
> [ 0.308793] io scheduler noop registered
> [ 0.308796] io scheduler deadline registered
> [ 0.308824] io scheduler cfq registered (default)
> [ 0.309041] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> [ 0.309086] pciehp: PCI Express Hot Plug Controller Driver version:
> 0.4
> [ 0.309327] input: Power Button
> as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
> [ 0.309341] ACPI: Power Button [VBTN]
> [ 0.309421] input: Power Button
> as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
> [ 0.309428] ACPI: Power Button [PWRF]
> [ 0.309599] ACPI: acpi_idle registered with cpuidle
> [ 0.336169] ERST: Table is not found!
> [ 0.336324] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
> [ 0.356697] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 0.356776] isapnp: Scanning for PnP cards...
> [ 0.446233] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 0.512641] Linux agpgart interface v0.103
> [ 0.512772] agpgart-intel 0000:00:00.0: Intel 845G Chipset
> [ 0.524260] agpgart-intel 0000:00:00.0: AGP aperture is 128M @
> 0xe8000000
> [ 0.526161] brd: module loaded
> [ 0.527069] loop: module loaded
> [ 0.527244] i2c-core: driver [adp5520] using legacy suspend method
> [ 0.527248] i2c-core: driver [adp5520] using legacy resume method
> [ 0.527435] ata_piix 0000:00:1f.1: version 2.13
> [ 0.527451] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
> [ 0.527479] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low)
> -> IRQ 18
> [ 0.527553] ata_piix 0000:00:1f.1: setting latency timer to 64
> [ 0.532267] scsi0 : ata_piix
> [ 0.532508] scsi1 : ata_piix
> [ 0.532575] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0
> irq 14
> [ 0.532580] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8
> irq 15
> [ 0.533273] Fixed MDIO Bus: probed
> [ 0.533347] PPP generic driver version 2.4.2
> [ 0.533471] tun: Universal TUN/TAP device driver, 1.6
> [ 0.533474] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
> [ 0.533619] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
> Driver
> [ 0.533668] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low)
> -> IRQ 23
> [ 0.533694] ehci_hcd 0000:00:1d.7: setting latency timer to 64
> [ 0.533700] ehci_hcd 0000:00:1d.7: EHCI Host Controller
> [ 0.533774] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
> bus number 1
> [ 0.533823] ehci_hcd 0000:00:1d.7: debug port 1
> [ 0.537700] ehci_hcd 0000:00:1d.7: cache line size of 64 is not
> supported
> [ 0.544084] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe300000
> [ 0.556475] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
> [ 0.556757] hub 1-0:1.0: USB hub found
> [ 0.556765] hub 1-0:1.0: 6 ports detected
> [ 0.556904] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [ 0.556931] uhci_hcd: USB Universal Host Controller Interface driver
> [ 0.557031] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low)
> -> IRQ 16
> [ 0.557045] uhci_hcd 0000:00:1d.0: setting latency timer to 64
> [ 0.557050] uhci_hcd 0000:00:1d.0: UHCI Host Controller
> [ 0.557129] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
> bus number 2
> [ 0.557175] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ff80
> [ 0.557365] hub 2-0:1.0: USB hub found
> [ 0.557373] hub 2-0:1.0: 2 ports detected
> [ 0.557473] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low)
> -> IRQ 19
> [ 0.557483] uhci_hcd 0000:00:1d.1: setting latency timer to 64
> [ 0.557487] uhci_hcd 0000:00:1d.1: UHCI Host Controller
> [ 0.557557] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
> bus number 3
> [ 0.557598] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ff60
> [ 0.557791] hub 3-0:1.0: USB hub found
> [ 0.557798] hub 3-0:1.0: 2 ports detected
> [ 0.557883] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low)
> -> IRQ 18
> [ 0.557892] uhci_hcd 0000:00:1d.2: setting latency timer to 64
> [ 0.557896] uhci_hcd 0000:00:1d.2: UHCI Host Controller
> [ 0.557971] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
> bus number 4
> [ 0.558008] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
> [ 0.558187] hub 4-0:1.0: USB hub found
> [ 0.558194] hub 4-0:1.0: 2 ports detected
> [ 0.558372] i8042: PNP: No PS/2 controller found. Probing ports
> directly.
> [ 0.565149] serio: i8042 KBD port at 0x60,0x64 irq 1
> [ 0.565170] serio: i8042 AUX port at 0x60,0x64 irq 12
> [ 0.565455] mousedev: PS/2 mouse device common for all mice
> [ 0.565704] rtc_cmos 00:05: RTC can wake from S4
> [ 0.565783] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
> [ 0.565811] rtc0: alarms up to one day, 242 bytes nvram
> [ 0.565972] device-mapper: uevent: version 1.0.3
> [ 0.566095] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07)
> initialised: dm-devel@xxxxxxxxxx
> [ 0.572349] device-mapper: multipath: version 1.2.0 loaded
> [ 0.572357] device-mapper: multipath round-robin: version 1.0.0
> loaded
> [ 0.572565] EISA: Probing bus 0 at eisa.0
> [ 0.572605] EISA: Detected 0 cards.
> [ 0.616306] cpuidle: using governor ladder
> [ 0.616309] cpuidle: using governor menu
> [ 0.616723] TCP cubic registered
> [ 0.616926] NET: Registered protocol family 10
> [ 0.617751] NET: Registered protocol family 17
> [ 0.617787] Registering the dns_resolver key type
> [ 0.617849] Using IPI No-Shortcut mode
> [ 0.618048] PM: Hibernation image not present or could not be loaded.
> [ 0.618065] registered taskstats version 1
> [ 0.618299] Magic number: 3:481:856
> [ 0.618413] rtc_cmos 00:05: setting system clock to 2011-07-18
> 22:49:00 UTC (1311029340)
> [ 0.618418] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
> [ 0.618421] EDD information not available.
> [ 0.720548] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-4167B, DL13, max
> UDMA/33
> [ 0.720558] ata2.01: ATAPI: HL-DT-ST GCE-8320B, 1.01, max MWDMA2
> [ 0.733508] ata1.00: HPA detected: current 117187500, native
> 117231408
> [ 0.733517] ata1.00: ATA-5: WDC WD600BB-75CAA0, 16.06V16, max
> UDMA/100
> [ 0.733522] ata1.00: 117187500 sectors, multi 8: LBA
> [ 0.734096] ata1.01: ATA-7: Maxtor 6Y060L0, YAR41VW0, max UDMA/133
> [ 0.734101] ata1.01: 120103200 sectors, multi 8: LBA
> [ 0.736219] ata2.00: configured for UDMA/33
> [ 0.784417] ata2.01: configured for MWDMA2
> [ 0.785462] ata1.00: configured for UDMA/100
> [ 0.876058] ata1.01: configured for UDMA/100
> [ 0.923893] isapnp: No Plug & Play device found
> [ 0.924379] scsi 0:0:0:0: Direct-Access ATA WDC WD600BB-75CA
> 16.0 PQ: 0 ANSI: 5
> [ 0.924677] sd 0:0:0:0: Attached scsi generic sg0 type 0
> [ 0.924859] scsi 0:0:1:0: Direct-Access ATA Maxtor 6Y060L0
> YAR4 PQ: 0 ANSI: 5
> [ 0.925059] sd 0:0:1:0: Attached scsi generic sg1 type 0
> [ 0.925167] sd 0:0:0:0: [sda] 117187500 512-byte logical blocks:
> (60.0 GB/55.8 GiB)
> [ 0.925251] sd 0:0:0:0: [sda] Write Protect is off
> [ 0.925256] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 0.925292] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 0.965407] sda: sda1 sda2 < sda5 >
> [ 0.965598] sda: p5 size 4876288 extends beyond EOD, enabling native
> capacity
> [ 0.965689] ata1: soft resetting link
> [ 0.969253] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-4167B
> DL13 PQ: 0 ANSI: 5
> [ 0.977409] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw
> xa/form2 cdda tray
> [ 0.977417] cdrom: Uniform CD-ROM driver Revision: 3.20
> [ 0.977655] sr 1:0:0:0: Attached scsi CD-ROM sr0
> [ 0.977789] sr 1:0:0:0: Attached scsi generic sg2 type 5
> [ 0.978689] scsi 1:0:1:0: CD-ROM HL-DT-ST CD-RW GCE-8320B
> 1.01 PQ: 0 ANSI: 5
> [ 0.982397] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda
> tray
> [ 0.982627] sr 1:0:1:0: Attached scsi CD-ROM sr1
> [ 0.982756] sr 1:0:1:0: Attached scsi generic sg3 type 5
> [ 0.984072] usb 1-3: new high speed USB device using ehci_hcd and
> address 3
> [ 1.143069] Freeing initrd memory: 12560k freed
> [ 1.164227] ata1.00: n_sectors mismatch 117187500 != 117231408
> [ 1.164233] ata1.00: new n_sectors matches native, probably late HPA
> unlock, n_sectors updated
> [ 1.181354] ata1.00: configured for UDMA/100
> [ 1.196341] ata1.01: configured for UDMA/100
> [ 1.196355] ata1: EH complete
> [ 1.196514] sd 0:0:1:0: [sdb] 120103200 512-byte logical blocks:
> (61.4 GB/57.2 GiB)
> [ 1.196556] sd 0:0:0:0: [sda] 117231408 512-byte logical blocks:
> (60.0 GB/55.8 GiB)
> [ 1.196668] sd 0:0:1:0: [sdb] Write Protect is off
> [ 1.196673] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
> [ 1.196749] sd 0:0:1:0: [sdb] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 1.205569] sda: detected capacity change from 60000000000 to
> 60022480896
> [ 1.205813] sdb: sdb1
> [ 1.265245] sda: sda1 sda2 < sda5 >
> [ 1.265692] sdb: detected capacity change from 0 to 61492838400
> [ 1.265844] sda: detected capacity change from 0 to 60022480896
> [ 1.265988] sdb: detected capacity change from 0 to 61492838400
> [ 1.266142] sd 0:0:1:0: [sdb] Attached SCSI disk
> [ 1.266246] sd 0:0:0:0: [sda] Attached SCSI disk
> [ 1.266289] Freeing unused kernel memory: 700k freed
> [ 1.267180] Write protecting the kernel text: 5192k
> [ 1.267219] Write protecting the kernel read-only data: 2148k
> [ 1.272088] Refined TSC clocksource calibration: 2524.921 MHz.
> [ 1.272099] Switching to clocksource tsc
> [ 1.308909] <30>udev[65]: starting version 167
> [ 1.420080] usb 2-1: new low speed USB device using uhci_hcd and
> address 2
> [ 1.625597] Floppy drive(s): fd0 is 1.44M
> [ 1.642362] FDC 0 is a post-1991 82077
> [ 1.685559] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
> [ 1.685565] e100: Copyright(c) 1999-2006 Intel Corporation
> [ 1.685636] e100 0000:02:08.0: PCI INT A -> GSI 20 (level, low) ->
> IRQ 20
> [ 1.788043] e100 0000:02:08.0: PME# disabled
> [ 1.788986] e100 0000:02:08.0: eth0: addr 0xfe1ef000, irq 20, MAC
> addr 00:07:e9:90:17:29
> [ 1.798101] usbcore: registered new interface driver usbhid
> [ 1.798106] usbhid: USB HID core driver
> [ 1.822042] input: Microsft Microsoft Wireless Desktop Receiver 3.1
> as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input2
> [ 1.822457] microsoft 0003:045E:00F9.0001: input,hidraw0: USB HID
> v1.11 Keyboard [Microsft Microsoft Wireless Desktop Receiver 3.1] on
> usb-0000:00:1d.0-1/input0
> [ 1.852033] usb 4-2: new low speed USB device using uhci_hcd and
> address 2
> [ 1.911014] microsoft 0003:045E:00F9.0002: fixing up Microsoft
> Wireless Receiver Model 1028 report descriptor
> [ 1.965028] input: Microsft Microsoft Wireless Desktop Receiver 3.1
> as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/input/input3
> [ 1.965492] microsoft 0003:045E:00F9.0002: input,hidraw1: USB HID
> v1.11 Mouse [Microsft Microsoft Wireless Desktop Receiver 3.1] on
> usb-0000:00:1d.0-1/input1
> [ 1.996213] EXT4-fs (sda1): mounted filesystem with ordered data
> mode. Opts: (null)
> [ 2.054102] input: S.T.D. Interact Gaming Device
> as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input4
> [ 2.054254] generic-usb 0003:05FD:3000.0003: input,hidraw2: USB HID
> v1.00 Joystick [S.T.D. Interact Gaming Device] on
> usb-0000:00:1d.2-2/input0
> [ 19.600231] Adding 2438140k swap on /dev/sda5. Priority:-1 extents:1
> across:2438140k
> [ 19.640765] <30>udev[264]: starting version 167
> [ 19.704443] lp: driver loaded but no devices found
> [ 19.866260] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
> [ 19.963909] intel_rng: Firmware space is locked read-only. If you
> can't or
> [ 19.963913] intel_rng: don't want to disable this in firmware setup,
> and if
> [ 19.963915] intel_rng: you are certain that your system has a
> functional
> [ 19.963917] intel_rng: RNG, try using the 'no_fwh_detect' option.
> [ 20.242007] type=1400 audit(1311029360.120:2): apparmor="STATUS"
> operation="profile_load" name="/sbin/dhclient" pid=448
> comm="apparmor_parser"
> [ 20.253510] type=1400 audit(1311029360.132:3): apparmor="STATUS"
> operation="profile_load"
> name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=448
> comm="apparmor_parser"
> [ 20.254090] type=1400 audit(1311029360.132:4): apparmor="STATUS"
> operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script"
> pid=448 comm="apparmor_parser"
> [ 20.491690] shpchp: Standard Hot Plug PCI Controller Driver version:
> 0.4
> [ 20.873176] ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 20.876164] e100 0000:02:08.0: eth0: NIC Link is Up 100 Mbps Full
> Duplex
> [ 20.876411] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 21.011125] parport_pc 00:08: reported by Plug and Play ACPI
> [ 21.011180] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO
> [PCSPP,TRISTATE,COMPAT,ECP]
> [ 21.041773] gameport gameport0: EMU10K1 is pci0000:02:02.1/gameport0,
> io 0xecf0, speed 1147kHz
> [ 21.127782] lp0: using parport0 (interrupt-driven).
> [ 21.393573] Linux video capture interface: v2.00
> [ 21.744940] cfg80211: Calling CRDA to update world regulatory domain
> [ 21.851425] type=1400 audit(1311029361.728:5): apparmor="STATUS"
> operation="profile_load" name="/usr/share/gdm/guest-session/Xsession"
> pid=630 comm="apparmor_parser"
> [ 21.869620] type=1400 audit(1311029361.748:6): apparmor="STATUS"
> operation="profile_replace" name="/sbin/dhclient" pid=633
> comm="apparmor_parser"
> [ 21.870537] type=1400 audit(1311029361.748:7): apparmor="STATUS"
> operation="profile_replace"
> name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=633
> comm="apparmor_parser"
> [ 21.871139] type=1400 audit(1311029361.748:8): apparmor="STATUS"
> operation="profile_replace"
> name="/usr/lib/connman/scripts/dhclient-script" pid=633
> comm="apparmor_parser"
> [ 21.908559] type=1400 audit(1311029361.788:9): apparmor="STATUS"
> operation="profile_load" name="/usr/bin/evince" pid=635
> comm="apparmor_parser"
> [ 21.956178] type=1400 audit(1311029361.836:10): apparmor="STATUS"
> operation="profile_load" name="/usr/bin/evince-previewer" pid=635
> comm="apparmor_parser"
> [ 21.959095] dcdbas dcdbas: Dell Systems Management Base Driver
> (version 5.6.0-3.2)
> [ 21.994265] type=1400 audit(1311029361.872:11): apparmor="STATUS"
> operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=635
> comm="apparmor_parser"
> [ 22.191599] uvcvideo: Found UVC 1.00 device USB 2.0 PC Cam
> (090c:a370)
> [ 22.202724] input: USB 2.0 PC Cam
> as /devices/pci0000:00/0000:00:1d.7/usb1/1-3/1-3:1.0/input/input5
> [ 22.202941] usbcore: registered new interface driver uvcvideo
> [ 22.202946] USB Video Class driver (v1.0.0)
> [ 23.055312] cfg80211: World regulatory domain updated:
> [ 23.055318] cfg80211: (start_freq - end_freq @ bandwidth),
> (max_antenna_gain, max_eirp)
> [ 23.055323] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
> (300 mBi, 2000 mBm)
> [ 23.055327] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz),
> (300 mBi, 2000 mBm)
> [ 23.055332] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
> (300 mBi, 2000 mBm)
> [ 23.055336] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz),
> (300 mBi, 2000 mBm)
> [ 23.055340] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz),
> (300 mBi, 2000 mBm)
> [ 23.116115] ppdev: user-space parallel port driver
> [ 23.449807] [drm] Initialized drm 1.1.0 20060810
> [ 23.765516] rt61pci 0000:02:0c.0: PCI INT A -> GSI 17 (level, low) ->
> IRQ 17
> [ 23.782588] cfg80211: Updating information on frequency 2412 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782595] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782599] cfg80211: Updating information on frequency 2417 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782604] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782608] cfg80211: Updating information on frequency 2422 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782612] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782616] cfg80211: Updating information on frequency 2427 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782621] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782624] cfg80211: Updating information on frequency 2432 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782629] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782632] cfg80211: Updating information on frequency 2437 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782637] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782640] cfg80211: Updating information on frequency 2442 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782645] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782648] cfg80211: Updating information on frequency 2447 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782653] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782657] cfg80211: Updating information on frequency 2452 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782661] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782665] cfg80211: Updating information on frequency 2457 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782669] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782673] cfg80211: Updating information on frequency 2462 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782678] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782681] cfg80211: Updating information on frequency 2467 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782686] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782690] cfg80211: Updating information on frequency 2472 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782694] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.782698] cfg80211: Updating information on frequency 2484 MHz for
> a 20 MHz width channel with regulatory rule:
> [ 23.782702] cfg80211: 2474000 KHz - 2494000 KHz @ KHz), (300 mBi,
> 2000 mBm)
> [ 23.815568] ieee80211 phy0: Selected rate control algorithm
> 'minstrel_ht'
> [ 23.817831] Registered led device: rt61pci-phy0::radio
> [ 23.817946] Registered led device: rt61pci-phy0::assoc
> [ 23.982478] EMU10K1X 0000:02:02.0: PCI INT A -> GSI 18 (level, low)
> -> IRQ 18
> [ 23.982517] Model 1003 Rev 00000000 Serial 10031102
> [ 23.990410] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) ->
> IRQ 16
> [ 24.013923] [drm] nouveau 0000:01:00.0: Detected an NV10 generation
> card (0x017200a3)
> [ 24.014176] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image
> from PRAMIN
> [ 24.060959] [drm] nouveau 0000:01:00.0: ... appears to be valid
> [ 24.061140] [drm] nouveau 0000:01:00.0: BMP BIOS found
> [ 24.061144] [drm] nouveau 0000:01:00.0: BMP version 5.21
> [ 24.061147] [drm] nouveau 0000:01:00.0: Bios version 04.17.00.45
> [ 24.061152] [drm] nouveau 0000:01:00.0: Found Display Configuration
> Block version 2.0
> [ 24.061157] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000100
> 000088b8
> [ 24.061161] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 02010111
> 00000003
> [ 24.061165] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 02010211
> 00000003
> [ 24.061169] [drm] nouveau 0000:01:00.0: Merging DCB entries 1 and 2
> [ 24.061317] [drm] nouveau 0000:01:00.0: Loading NV17 power sequencing
> microcode
> [ 24.061323] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at
> offset 0xCA44
> [ 24.061359] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at
> offset 0xCD7C
> [ 24.068095] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at
> offset 0xCB44
> [ 24.093809] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at
> offset 0xD27E
> [ 24.093823] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at
> offset 0xCCD8
> [ 24.147410] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 24.653475] [drm] nouveau 0000:01:00.0: 1 available performance
> level(s)
> [ 24.653482] [drm] nouveau 0000:01:00.0: 0: memory 332MHz
> [ 24.653493] [drm] nouveau 0000:01:00.0: c: memory 333MHz core 249MHz
> [ 24.655661] [TTM] Zone kernel: Available graphics memory: 442920
> kiB.
> [ 24.655666] [TTM] Zone highmem: Available graphics memory: 512278
> kiB.
> [ 24.655670] [TTM] Initializing pool allocator.
> [ 24.655693] [drm] nouveau 0000:01:00.0: Detected 64MiB VRAM
> [ 24.655984] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
> [ 24.656689] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x
> mode
> [ 24.656726] nouveau 0000:01:00.0: putting AGP V2 device into 4x mode
> [ 24.656758] [drm] nouveau 0000:01:00.0: 128 MiB GART (aperture)
> [ 24.658841] [drm] Supports vblank timestamp caching Rev 1
> (10.10.2010).
> [ 24.658846] [drm] No driver support for vblank timestamp query.
> [ 24.663971] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga
> encoder (output 0)
> [ 24.663980] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV
> encoder (output 1)
> [ 24.820907] [drm] nouveau 0000:01:00.0: allocated 1024x768 fb:
> 0x49000, bo f194bc00
> [ 24.821267] fbcon: nouveaufb (fb0) is primary device
> [ 24.822774] Console: switching to colour frame buffer device 128x48
> [ 24.822812] fb0: nouveaufb frame buffer device
> [ 24.822815] drm: registered panic notifier
> [ 24.822831] [drm] Initialized nouveau 0.0.16 20090420 for
> 0000:01:00.0 on minor 0
> [ 25.534018] EXT4-fs (sda1): re-mounted. Opts:
> errors=remount-ro,commit=0
> [ 26.187238] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on vga
> encoder (output 0)
> [ 26.187245] [drm] nouveau 0000:01:00.0: Output VGA-1 is running on
> CRTC 0 using output A
> [ 31.200009] eth0: no IPv6 routers present
> [ 32.498065] EXT4-fs (sda1): re-mounted. Opts:
> errors=remount-ro,commit=0
>
> Module Size Used by
> nouveau 621970 3
> snd_emu10k1x 19498 2
> snd_ac97_codec 105614 1 snd_emu10k1x
> snd_pcm 80042 2 snd_emu10k1x,snd_ac97_codec
> arc4 12473 2
> ttm 65184 1 nouveau
> rt61pci 27265 0
> snd_seq_midi 13132 0
> crc_itu_t 12627 1 rt61pci
> drm_kms_helper 40745 1 nouveau
> rt2x00pci 13986 1 rt61pci
> snd_rawmidi 25269 2 snd_emu10k1x,snd_seq_midi
> rt2x00lib 39075 2 rt61pci,rt2x00pci
> snd_seq_midi_event 14475 1 snd_seq_midi
> mac80211 257001 2 rt2x00pci,rt2x00lib
> snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event
> binfmt_misc 13213 1
> ppdev 12849 0
> snd_timer 28659 2 snd_pcm,snd_seq
> drm 180037 5 nouveau,ttm,drm_kms_helper
> uvcvideo 66851 0
> snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq
> dcdbas 14054 0
> snd 55295 11
> snd_emu10k1x,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
> cfg80211 156212 2 rt2x00lib,mac80211
> i2c_algo_bit 13184 1 nouveau
> soundcore 12600 1 snd
> psmouse 73312 0
> emu10k1_gp 12566 0
> parport_pc 32111 1
> gameport 15027 2 emu10k1_gp
> ac97_bus 12642 1 snd_ac97_codec
> videodev 75143 1 uvcvideo
> video 18951 1 nouveau
> joydev 17322 0
> eeprom_93cx6 12653 1 rt61pci
> serio_raw 12990 0
> snd_page_alloc 14073 2 snd_emu10k1x,snd_pcm
> shpchp 32345 0
> lp 13349 0
> parport 36746 3 ppdev,parport_pc,lp
> hid_microsoft 12745 0
> usbhid 41704 0
> hid 77084 2 hid_microsoft,usbhid
> e100 40108 0
> floppy 60032 0
>
>
>
