Fibonacci,
We are closer but not there yet :(
I was hesitant because scanModem reported agrsm-11c11040 too
Predictive diagnostics for card in bus 02:06.4:
Modem chipset detected on
NAME="Communication controller: Texas Instruments PCIxx12 GemCore
based SmartCard controller"
CLASS=0780
PCIDEV=104c:803d
SUBSYS=103c:30ac
IRQ=11
HDA2=00:1b.0
HDAchipVendorID=11c1
CHIP=0x11c13026
IDENT=slmodemd
SLMODEMD_DEVICE=hw:0,6
Driver=snd-hda-intel
package=agrsm-11c11040
That is definitely disagreeing. If we can get output of
$ sudo aplay -l
or run
$ sudo alsa-info.sh
and send us output
http://git.alsa-project.org/?p=alsa-driver.git;a=blob_plain;f=utils/alsa-info.sh
This way we can try to determine which driver is needed to load
(snd_????-modem) if possible.
Regards,
Antonio
On Sun, Jan 23, 2011 at 12:01 PM, Fibonacci Prower
<fibonacci.prower@xxxxxxxxx> wrote:
> 2011/1/23 Antonio Olivares <olivares14031@xxxxxxxxx>:
>> Fibonacci,
>>
>> There are two conflicting drivers here:
>>
>> Potentially useful modem drivers now loaded are:
>> snd_hda_intel slamr
>>
>> Try to do the following:
>>
>> $ sudo modprobe -r slamr
> No problem here:
>> $ sudo modprobe -r snd_hda_intel
> FATAL: Module snd_hda_intel is in use.
>> then reload the latter one
>> $ sudo modprobe snd_hda_intel
>> $ sudo slmodemd -c USA --alsa hw:0,6
> SmartLink Soft Modem: version 2.9.11 Sep 6 2010 12:33:03
> symbolic link `/dev/ttySL0' -> `/dev/pts/1' created.
> modem `hw:0,6' created. TTY is `/dev/pts/1'
> error: locked memory limit too low:
> error: need 8388608 bytes, have 65536 bytes
> error: try 'ulimit -l 8192'
>
> So I'm back to starting a root shell and then running this:
> # ulimit -l 8192 && slmodemd -c USA --alsa hw:0,6
>>
>> Leave this running in the background, fire up another terminal shell/tab and run
>> $ sudo wvdialconf /etc/wvdial.conf
>
> Editing `/etc/wvdial.conf'.
>
> Scanning your serial ports for a modem.
>
> Modem Port Scan<*1>: S0 S1
> ttyS2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> ttyS2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> ttyS2<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
> Modem Port Scan<*1>: S3
> WvModem<*1>: Cannot get information for serial port.
> ttySL0<*1>: ATQ0 V1 E1 -- OK
> ttySL0<*1>: ATQ0 V1 E1 Z -- OK
> ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK
> ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
> ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
> ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
> ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem
> ttySL0<*1>: Speed 4800: AT -- OK
> ttySL0<*1>: Speed 9600: AT -- OK
> ttySL0<*1>: Speed 19200: AT -- OK
> ttySL0<*1>: Speed 38400: AT -- OK
> ttySL0<*1>: Speed 57600: AT -- OK
> ttySL0<*1>: Speed 115200: AT -- OK
> ttySL0<*1>: Speed 230400: AT -- OK
> ttySL0<*1>: Speed 460800: AT -- OK
> ttySL0<*1>: Max speed is 460800; that should be safe.
> ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
>
> Found a modem on /dev/ttySL0.
> Modem configuration written to /etc/wvdial.conf.
> ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
>
>>
>> to be safe you may run
>> $ dmesg | grep 'sl*' and output of
> Shouldn't it be 'sl' instead of 'sl*'? Anyway this is the output of the former:
> [ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0,
> CPUs=2, Nodes=1
> [ 0.172235] bio: create slab <bio-0> at 0
> [ 0.560686] Cannot allocate resource for EISA slot 1
> [ 0.560688] Cannot allocate resource for EISA slot 2
> [ 0.560691] Cannot allocate resource for EISA slot 3
> [ 0.560693] Cannot allocate resource for EISA slot 4
> [ 0.560695] Cannot allocate resource for EISA slot 5
> [ 0.560697] Cannot allocate resource for EISA slot 6
> [ 0.560699] Cannot allocate resource for EISA slot 7
> [ 0.560701] Cannot allocate resource for EISA slot 8
> [ 0.581865] input: AT Translated Set 2 keyboard as
> /devices/platform/i8042/serio0/input/input3
> [ 1.135273] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5
> Gbps 0x1 impl SATA mode
> [ 1.135278] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led
> clo pmp pio slum part
> [ 28.012927] slamr: SmartLink AMRMO modem.
>> $ sudo tail -f /var/log/messages
> Jan 23 12:48:23 prower-laptop kernel: [ 29.696342] Bluetooth: BNEP
> filters: protocol multicast
> Jan 23 12:48:23 prower-laptop kernel: [ 29.700521] Bluetooth: SCO
> (Voice Link) ver 0.6
> Jan 23 12:48:23 prower-laptop kernel: [ 29.700524] Bluetooth: SCO
> socket layer initialized
> Jan 23 12:48:23 prower-laptop kernel: [ 29.815105] Bluetooth: RFCOMM
> TTY layer initialized
> Jan 23 12:48:23 prower-laptop kernel: [ 29.815112] Bluetooth: RFCOMM
> socket layer initialized
> Jan 23 12:48:23 prower-laptop kernel: [ 29.815115] Bluetooth: RFCOMM ver 1.11
> Jan 23 12:48:25 prower-laptop kernel: [ 31.407768] EXT4-fs (sda5):
> re-mounted. Opts: errors=remount-ro,commit=0
> Jan 23 12:48:25 prower-laptop pulseaudio[1626]: lock-autospawn.c:
> Cannot access autospawn lock.
> Jan 23 12:48:26 prower-laptop kernel: [ 32.660192] input: PS/2
> Generic Mouse as /devices/platform/i8042/serio4/serio5/input/input8
> Jan 23 12:48:26 prower-laptop kernel: [ 32.888990] EXT4-fs (sda5):
> re-mounted. Opts: errors=remount-ro,commit=0
>> last few lines when running the above commands. Report back presently.
>>
>> Regards,
>>
>> Antonio
>>
>> On Sun, Jan 23, 2011 at 2:43 AM, Fibonacci Prower
>> <fibonacci.prower@xxxxxxxxx> wrote:
>>> 2011/1/23 Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>:
>>>> Fibonacci
>>>>
>>>> Please disconnect the USB devices as much as possible, and take out
>>>> any PCMCIA cards
>>>> Your System seems low on RAM. Again run scanModem
>>>> On your first round the important ALSA diagnostics did not get written
>>>> to ModemData.txt
>>>> even the directions to use slmodemd seem correct.
>>>>
>>>
>>> No user-removable USB devices or PCMCIA cards were connnected at the
>>> time I ran scanModem.
>>> The new ModemData.txt is on the bottom.
>>>
>>>> The logic in my scanModem script is not sophisticated enought to
>>>> always succeed when there on two candidate COMM cards.
>>>>
>>>> But as I read it, there is an Agere chip
>>>> CHIP=0x11c13026, hosted on the Subsystem of the High Defintion Audio card
>>>> with the real smarts in the slmodemd helper using the dynamically created
>>>> SLMODEMD_DEVICE=hw:0,6
>>>> corresponding to /dev/ttySL0 -> /dev/pts/2 (the real port)
>>>>
>>>> You can first try:
>>>> $ lsmod
>>>> to display drivers, then starting from the top of list, try removing
>>>> non-essential drivers with
>>>> $ sudo modprobe -r DriverNames
>>>>
>>>
>>> How do I know which driver does what?
>>>
>>>> A first functionality test is detecting the modem with:
>>>> $ sudo wvdialconf
>>>>
>>>
>>> This is what I get:
>>>
>>> Editing `/etc/wvdial.conf'.
>>>
>>> Scanning your serial ports for a modem.
>>>
>>> Modem Port Scan<*1>: S0 S1
>>> ttyS2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>>> ttyS2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>>> ttyS2<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>>> Modem Port Scan<*1>: S3
>>>
>>>
>>> Sorry, no modem was detected! Is it in use by another program?
>>> Did you configure it properly with setserial?
>>>
>>> Please read the FAQ at http://open.nit.ca/wiki/?WvDial
>>>
>>> If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>.
>>>
>>>> Try these and report back
>>>>
>>>> MarvS
>>>> scanModem maintainer
>>>> On Sun, Jan 23, 2011 at 2:15 AM, Fibonacci Prower
>>>> <fibonacci.prower@xxxxxxxxx> wrote:
>>>>> Hello.
>>>>>
>>>>> I'm trying to use the modem which came with my laptop to connect to
>>>>> the internet. Unfortunately it's a winmodem, like most.
>>>>> The output of scanModem (attached) is not clear enough as to which
>>>>> driver should be used on this modem. I finally installed and
>>>>> configured sl-modem-daemon - but I still don't know which country
>>>>> should I specify, since Colombia (where I currently live) is not one
>>>>> of the available options.
>>>>> It appears, nevertheless, that my system is talking to the modem. I
>>>>> can't connect to the internet, though, since I always get this message
>>>>> with either Gnome-PPP or WvDial:
>>>>>
>>>>> --> WvDial: Internet dialer version 1.60
>>>>> --> Cannot get information for serial port.
>>>>> --> Initializing modem.
>>>>> --> Sending: ATZ
>>>>> ATZ
>>>>> OK
>>>>> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>>>>> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>>>>> OK
>>>>> --> Modem initialized.
>>>>> --> Sending: ATM1L3DT019479472323
>>>>> --> Waiting for carrier.
>>>>> ATM1L3DT019479472323
>>>>> NO CARRIER
>>>>> --> No Carrier! Trying again.
>>>>>
>>>>> That happens even after I've set Carrier Check = no on wvdial.conf, so
>>>>> I'm stuck here.
>>>>>
>>>>> After rebooting, I get the following error message from both Gnome-PPP
>>>>> and WvDial:
>>>>>
>>>>> --> Cannot open /dev/ttySL0: No such file or directory
>>>>> --> Cannot open /dev/ttySL0: No such file or directory
>>>>> --> Cannot open /dev/ttySL0: No such file or directory
>>>>>
>>>>> Problem is, /dev/ttySL0 is there and world-writable. OK, then, I'll
>>>>> try restarting slmodemd:
>>>>>
>>>>> $ sudo slmodemd -c USA --alsa hw:0,6
>>>>> error: locked memory limit too low:
>>>>> error: need 8388608 bytes, have 65536 bytes
>>>>> error: try 'ulimit -l 8192'
>>>>>
>>>>> Oh well. Since sudo ulimit doesn't work, I need to start a root shell,
>>>>> THEN run the ulimit code suggested, THEN slmodemd -c USA --alsa
>>>>> hw:0,6, and THEN... nothing. I'm right back at square one - no
>>>>> carrier.
>>>>>
>>>>> Also: the exact same setup works under Windows XP, so I know there's
>>>>> nothing wrong with my hardware.
>>>>>
>>>>> The full content of ModemData.txt follows:
>>>>>
>>>>> Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server,
>>>>> as HTML can contain viruses. Use as the email Subject Line:
>>>>> YourName, YourCountry kernel 2.6.35-24-generic
>>>>> With this Subject Line cogent experts will be alerted, and useful
>>>>> case names left in the Archive.
>>>>> YourCountry will enable Country specific guidance. Linux experts in YourCountry
>>>>> can be found through: http://www.linux.org/groups/index.html.
>>>>> They will know your Country's modem code, which may be essential for
>>>>> dialup service.
>>>>> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an
>>>>> Internet Provider mail filters.
>>>>> So in a day, also check the Archived responses at http://www.linmodems.org
>>>>> -------------------------- System information ----------------------------
>>>>> CPU=i686, Ubuntu , ALSA_version=1.0.23
>>>>> Linux version 2.6.35-24-generic (buildd@vernadsky) (gcc version 4.4.5
>>>>> (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #42-Ubuntu SMP Thu Dec 2 01:41:57
>>>>> UTC 2010
>>>>> scanModem update of: 2010_12_12
>>>>> The modem symbolic link is /dev/modem -> ttySL0
>>>>> The slmodemd set symbolic link is /dev/ttySL0 -> /dev/pts/2
>>>>> Distrib_ID=Ubuntu
>>>>> DistribCodeName=maverick
>>>>> AptRepositoryStem=http://ubuntu.wikimedia.org/ubuntu/
>>>>>
>>>>>
>>>>> The dkms driver upgrade utilities are installed,
>>>>>
>>>>> There are no blacklisted modem drivers in /etc/modprobe* files
>>>>>
>>>>> Potentially useful modem drivers now loaded are:
>>>>> snd_hda_intel
>>>>>
>>>>> Attached USB devices are:
>>>>> ID 08ff:2580 AuthenTec, Inc. AES2501 Fingerprint Sensor
>>>>> ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface
>>>>> [Integrated Module]
>>>>> ID 12d1:1003 Huawei Technologies Co., Ltd. E220 HSDPA Modem / E270
>>>>> HSDPA/HSUPA Modem
>>>>> ID 0781:5406 SanDisk Corp. Cruzer Micro U3
>>>>> If a cellphone is not detected, see
>>>>> http://ubuntuforums.org/archive/index.php/t-878554.html
>>>>> A sample report is:
>>>>> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
>>>>>
>>>>> If a USB modem or cellphone is attached and was not detected, please
>>>>> provide available information in your request to discuss@xxxxxxxxxxxxx
>>>>>
>>>>> Candidate PCI devices with modem chips are:
>>>>> 02:06.4 Communication controller: Texas Instruments PCIxx12 GemCore
>>>>> based SmartCard controller
>>>>> 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High
>>>>> Definition Audio Controller (rev 01)
>>>>> High Definition Audio cards can host modem chips.
>>>>>
>>>>> For candidate card in slot 02:06.4, firmware information and bootup
>>>>> diagnostics are:
>>>>> PCI slot PCI ID SubsystemID Name
>>>>> ---------- --------- --------- --------------
>>>>> 02:06.4 104c:803d 103c:30ac Communication controller: Texas
>>>>> Instruments PCIxx12 GemCore based SmartCard controller
>>>>>
>>>>> Modem interrupt assignment and sharing:
>>>>> --- Bootup diagnostics for card in PCI slot 02:06.4 ----
>>>>> [ 0.293990] pci 0000:02:06.4: reg 10: [mem 0xe420a000-0xe420afff]
>>>>> [ 0.294000] pci 0000:02:06.4: reg 14: [mem 0xe420b000-0xe420bfff]
>>>>> [ 0.294070] pci 0000:02:06.4: supports D1 D2
>>>>> [ 0.294072] pci 0000:02:06.4: PME# supported from D0 D1 D2 D3hot
>>>>> [ 0.294078] pci 0000:02:06.4: PME# disabled
>>>>>
>>>>> The PCI slot 02:06.4 of the modem card may be disabled early in
>>>>> a bootup process, but then enabled later. If modem drivers load
>>>>> but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
>>>>> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
>>>>> if help is needed.
>>>>>
>>>>>
>>>>> For candidate card in slot 00:1b.0, firmware information and bootup
>>>>> diagnostics are:
>>>>> PCI slot PCI ID SubsystemID Name
>>>>> ---------- --------- --------- --------------
>>>>> 00:1b.0 8086:27d8 103c:30ac Audio device: Intel Corporation
>>>>> N10/ICH 7 Family High Definition Audio Controller
>>>>>
>>>>> Modem interrupt assignment and sharing:
>>>>> 45: 16836 0 PCI-MSI-edge hda_intel
>>>>> --- Bootup diagnostics for card in PCI slot 00:1b.0 ----
>>>>> [ 0.290686] pci 0000:00:1b.0: reg 10: [mem 0xe4700000-0xe4703fff 64bit]
>>>>> [ 0.290750] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
>>>>> [ 0.290755] pci 0000:00:1b.0: PME# disabled
>>>>> [ 28.827744] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
>>>>> [ 28.827779] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
>>>>> [ 28.827788] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level,
>>>>> low) -> IRQ 16
>>>>> [ 28.827858] HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X
>>>>> [ 28.827891] HDA Intel 0000:00:1b.0: setting latency timer to 64
>>>>>
>>>>> The PCI slot 00:1b.0 of the modem card may be disabled early in
>>>>> a bootup process, but then enabled later. If modem drivers load
>>>>> but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
>>>>> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
>>>>> if help is needed.
>>>>>
>>>>>
>>>>> === Finished firmware and bootup diagnostics, next deducing cogent software. ===
>>>>>
>>>>> Predictive diagnostics for card in bus 02:06.4:
>>>>> Modem chipset detected on
>>>>> NAME="Communication controller: Texas Instruments PCIxx12 GemCore
>>>>> based SmartCard controller"
>>>>> CLASS=0780
>>>>> PCIDEV=104c:803d
>>>>> SUBSYS=103c:30ac
>>>>> IRQ=11
>>>>> HDA2=00:1b.0
>>>>> HDAchipVendorID=11c1
>>>>> CHIP=0x11c13026
>>>>> IDENT=slmodemd
>>>>> SLMODEMD_DEVICE=hw:0,6
>>>>> Driver=snd-hda-intel
>>>>> package=agrsm-11c11040
>>>>>
>>>>> For candidate modem in: 02:06.4
>>>>> 0780 Communication controller: Texas Instruments PCIxx12 GemCore
>>>>> based SmartCard controller
>>>>> Primary device ID: 104c:803d
>>>>> Support type needed or chipset: slmodemd
>>>>>
>>>>>
>>>>> An ALSA (Advanced Linux Sound Architecture) modem driver: snd-hda-intel
>>>>> provides Low Level support enabling contact with the modem hardware.
>>>>> For all BUT Conexant chip soft modems (using hsfmodem software)
>>>>> complementary High Level support is through a Smartlink utility: slmodemd
>>>>>
>>>>> Download from http://linmodems.technion.ac.il/packages/smartlink/
>>>>> the package SLMODEMD_gcc4.4_alsa1.0.23.tar.gz having a compiled
>>>>> slmodemd. Unpack under Linux with:
>>>>> $ tar zxf SLMODEMD_gcc4.4_alsa1.0.23.tar.gz
>>>>> and read instructions therein. But briefly, the modem is setup with command:
>>>>> sudo slmodemd -c YOUR_COUNTRY --alsa hw:0,6
>>>>> reporting dynamic creation of ports:
>>>>> /dev/ttySL0 --> /dev/pts/N , with N some number
>>>>> Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow
>>>>> through guidance.
>>>>>
>>>>>
>>>>> Writing DOCs/Intel.txt
>>>>> Writing DOCs/Smartlink.txt
>>>>> ============ end Smartlink section =====================
>>>>>
>>>>> The AgereSystems/LSI agrsm code supports compiling of a agrmodem +
>>>>> agrserial driver pair.
>>>>> There are a few different chipsets which use this driver pair, but
>>>>> they use different code resources:
>>>>> Chipsets KV* PackageNames (most current as of November 2009)
>>>>> ----------------------------------------------------------------------------------------------
>>>>> 11c1:048c and 11c1:048f 2.6.29
>>>>> agrsm048pci-2.1.60_20100108_i386.deb or
>>>>> agrsm048pci-2.1.60_20100108.tar.gz
>>>>> 11c1:0620 2.6.31
>>>>> agrsm06pci-2.1.80_20100106_i386.deb or
>>>>> agrsm06pci-2.1.80~20100106.tar.gz !!
>>>>> 11c11040 (on HDA audio cards) 2.6.31
>>>>> agrsm-11c11040_20091225_i386.deb or
>>>>> agrsm-11c11040-2.1.80~20091225.tar.bz2 !!
>>>>> All available at:
>>>>> http://linmodems.technion.ac.il/packages/ltmodem/11c11040/
>>>>> Additionally there are;
>>>>> automation & testing agrsm-tools_0.0.1_all.deb or
>>>>> agrsm-tools-0.0.1-2.noarch.rpm
>>>>> General background agrsm_howto.txt
>>>>> ------------------------------------------------------------------------------------------------
>>>>> * KV == latest kernel release with a reported success
>>>>> !! Latest update with major credit to Nikolay Zhuravlev
>>>>> But see conflict issue:
>>>>> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg02753.html
>>>>> For the 11c11040 chip with kernels 2.6.31 and later a change in a
>>>>> modules loading settingmay be necessary.
>>>>> Within the file /etc/modprobe.d/alsa-base.conf (or equivalent for
>>>>> your Distro), change the phrase:
>>>>> options snd-hda-intel power_save=10
>>>>> to:
>>>>> options snd-hda-intel power_save=0
>>>>> or the agrsm drivers will not function. For Ubuntu related systems
>>>>> this can be done with:
>>>>> $ sudo gedit /etc/modprobe.d/alsa-base.conf
>>>>>
>>>>> Report from Bjorn Wielens:
>>>>> Please note- trying to load the modules on a OpenSuSE 11.2 system gives
>>>>> an error about the module_version symbol. Using:
>>>>> # modprobe --force agrmodem
>>>>> # modprobe --force agrserial
>>>>> is necessary to load the drivers, and does not appear to cause ill effects.
>>>>>
>>>>>
>>>>> All of the above packages are dkms competent. This means that if your
>>>>> Linux distros dkms package
>>>>> is previously installed, if provides for future updates matching
>>>>> forthcoming kernels.
>>>>>
>>>>> -------------- end Agere Systems section -------------------
>>>>>
>>>>>
>>>>> Predictive diagnostics for card in bus 00:1b.0:
>>>>> Modem chipset not detected on
>>>>> NAME="Audio device: Intel Corporation N10/ICH 7 Family High Definition
>>>>> Audio Controller "
>>>>> CLASS=0403
>>>>> PCIDEV=8086:27d8
>>>>> SUBSYS=103c:30ac
>>>>> IRQ=45
>>>>>
>>>>> For candidate modem in: 00:1b.0
>>>>> 0403 Audio device: Intel Corporation N10/ICH 7 Family High
>>>>> Definition Audio Controller
>>>>> Primary device ID: 8086:27d8
>>>>> Support type needed or chipset:
>>>>>
>>>>>
>>>>> Completed candidate modem analyses.
>>>>>
>>>>> The base of the UDEV device file system is: /dev/.udev
>>>>>
>>>>> Versions adequately match for the compiler installed: 4.4.5
>>>>> and the compiler used in kernel assembly: 4.4.5
>>>>>
>>>>> linux-headers-2.6.35-24-generic resources needed for compiling are
>>>>> not manifestly ready!
>>>>>
>>>>> If compiling is necessary packages must be installed, providing:
>>>>> linux-headers-2.6.35-24-generic
>>>>>
>>>>>
>>>>> If a driver compilation fails, with message including some lack of
>>>>> some FileName.h (stdio.h for example), then
>>>>> Some additional kernel-header files need installation to /usr/include.
>>>>> The minimal additional packages are libc6-dev
>>>>> and any of its dependents, under Ubuntu linux-libc-dev
>>>>>
>>>>> If an alternate ethernet connection is available,
>>>>> $ apt-get update
>>>>> $ apt-get -s install linux-kernel-devel
>>>>> will install needed packages.
>>>>> For Debian/Ubuntu related distributions, run the following command to
>>>>> display the needed package list:
>>>>>
>>>>> Otherwise packages have to be found through http://packages.ubuntu.com
>>>>> Once downloaded and transferred into a Linux partition,
>>>>> they can be installed alltogether with:
>>>>> $ sudo dpkg -i *.deb
>>>>>
>>>>> Checking settings of: /etc/ppp/options
>>>>> asyncmap 0
>>>>> noauth
>>>>> crtscts
>>>>> lock
>>>>> hide-password
>>>>> modem
>>>>> proxyarp
>>>>> lcp-echo-interval 30
>>>>> lcp-echo-failure 4
>>>>> noipx
>>>>>
>>>>> In case of a message like:
>>>>> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
>>>>> see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
>>>>>
>>>>> For guidance on FAX usage, get from
>>>>> http://linmodems.technion.ac.il/packages/ get faxing.tar.gz
>>>>> It has samples for a modem using port /dev/ttySL0, which must be
>>>>> changed to match your modem's port.
>>>>>
>>>>> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 eth2 ppp0
>>>>> Which can interfere with Browser naviagation.
>>>>>
>>>>> Don't worry about the following, it is for experts should trouble
>>>>> shooting be necessary.
>>>>> ==========================================================
>>>>>
>>>>> Checking for modem support lines:
>>>>> --------------------------------------
>>>>> /device/modem symbolic link: lrwxrwxrwx 1 root root 6
>>>>> 2010-12-21 22:43 /dev/modem -> ttySL0
>>>>> slmodemd created symbolic link /dev/ttySL0: lrwxrwxrwx 1 root root 10
>>>>> 2010-12-21 22:43 /dev/ttySL0 -> /dev/pts/2
>>>>> Within /etc/udev/ files:
>>>>>
>>>>> Within /etc/modprobe.conf files:
>>>>> /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
>>>>> /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
>>>>> /etc/modprobe.d/sl-modem.conf:install slamr /sbin/modprobe -qb
>>>>> ungrab-winmodem; /sbin/modprobe --ignore-install slamr; test -e
>>>>> /dev/slamr0 && (chmod 660 /dev/slamr0 && chgrp dialout /dev/slamr0) ||
>>>>> (/bin/mknod -m 660 /dev/slamr0 c 242 0 2>/dev/null && chgrp dialout
>>>>> /dev/slamr0)
>>>>> /etc/modprobe.d/sl-modem.conf:install slusb /sbin/modprobe -qb
>>>>> ungrab-winmodem; /sbin/modprobe --ignore-install slusb; test -e
>>>>> /dev/slusb0 && (chmod 660 /dev/slusb0 && chgrp dialout /dev/slusb0) ||
>>>>> (/bin/mknod -m 660 /dev/slusb0 c 243 0 2>/dev/null && chgrp dialout
>>>>> /dev/slusb0)
>>>>> /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in
>>>>> order to blacklist unwanted modem drivers
>>>>> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
>>>>> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
>>>>> Within any ancient /etc/devfs files:
>>>>>
>>>>> Within ancient kernel 2.4.n /etc/module.conf files:
>>>>>
>>>>> --------- end modem support lines --------
>>>>>
>>>>>
>>>>> --
>>>>> $0='!/msfQ0yjoV!fe!sfldbi!psup!pmpT'x19xor print+map{("\e[7m \e[0m",
>>>>> chr ord(chop$0)-1)[$_].("\n")[++$i%72]}split//,unpack'B*',pack'H*',(
>>>>> $P='F'x18)."8186078739E1F0F0E19FCF333319CCE6667383CF0733099E67E7F39"
>>>>> ."FCF3333218067E7F39FCF3333319E6666739F860787399E70F0E1$P"#Perl rulz
>>>>>
>>>>
>>>
>>> This is ModemData.txt:
>>>
>>> Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server,
>>> as HTML can contain viruses. Use as the email Subject Line:
>>> YourName, YourCountry kernel 2.6.35-25-generic
>>> With this Subject Line cogent experts will be alerted, and useful
>>> case names left in the Archive.
>>> YourCountry will enable Country specific guidance. Linux experts in
>>> YourCountry
>>> can be found through: http://www.linux.org/groups/index.html.
>>> They will know your Country's modem code, which may be essential for
>>> dialup service.
>>> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an
>>> Internet Provider mail filters.
>>> So in a day, also check the Archived responses at http://www.linmodems.org
>>> -------------------------- System information ----------------------------
>>> CPU=i686, Ubuntu , ALSA_version=1.0.23
>>> Linux version 2.6.35-25-generic (buildd@roseapple) (gcc version 4.4.5
>>> (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #43-Ubuntu SMP Thu Jan 6 22:25:16
>>> UTC 2011
>>> scanModem update of: 2010_12_12
>>> The modem symbolic link is /dev/modem -> ttySL0
>>> Distrib_ID=Ubuntu
>>> DistribCodeName=maverick
>>> AptRepositoryStem=http://ubuntu.wikimedia.org/ubuntu/
>>>
>>>
>>> The dkms driver upgrade utilities are installed,
>>>
>>> There are no blacklisted modem drivers in /etc/modprobe* files
>>>
>>> Potentially useful modem drivers now loaded are:
>>> snd_hda_intel slamr
>>>
>>> Attached USB devices are:
>>> ID 08ff:2580 AuthenTec, Inc. AES2501 Fingerprint Sensor
>>> ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface
>>> [Integrated Module]
>>> If a cellphone is not detected, see
>>> http://ubuntuforums.org/archive/index.php/t-878554.html
>>> A sample report is:
>>> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
>>>
>>> If a USB modem or cellphone is attached and was not detected, please
>>> provide available information in your request to discuss@xxxxxxxxxxxxx
>>>
>>> Candidate PCI devices with modem chips are:
>>> 02:06.4 Communication controller: Texas Instruments PCIxx12 GemCore
>>> based SmartCard controller
>>> 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High
>>> Definition Audio Controller (rev 01)
>>> High Definition Audio cards can host modem chips.
>>>
>>> For candidate card in slot 02:06.4, firmware information and bootup
>>> diagnostics are:
>>> PCI slot PCI ID SubsystemID Name
>>> ---------- --------- --------- --------------
>>> 02:06.4 104c:803d 103c:30ac Communication controller: Texas
>>> Instruments PCIxx12 GemCore based SmartCard controller
>>>
>>> Modem interrupt assignment and sharing:
>>> --- Bootup diagnostics for card in PCI slot 02:06.4 ----
>>> [ 0.287491] pci 0000:02:06.4: reg 10: [mem 0xe420a000-0xe420afff]
>>> [ 0.287502] pci 0000:02:06.4: reg 14: [mem 0xe420b000-0xe420bfff]
>>> [ 0.287572] pci 0000:02:06.4: supports D1 D2
>>> [ 0.287574] pci 0000:02:06.4: PME# supported from D0 D1 D2 D3hot
>>> [ 0.287580] pci 0000:02:06.4: PME# disabled
>>>
>>> The PCI slot 02:06.4 of the modem card may be disabled early in
>>> a bootup process, but then enabled later. If modem drivers load
>>> but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
>>> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
>>> if help is needed.
>>>
>>>
>>> For candidate card in slot 00:1b.0, firmware information and bootup
>>> diagnostics are:
>>> PCI slot PCI ID SubsystemID Name
>>> ---------- --------- --------- --------------
>>> 00:1b.0 8086:27d8 103c:30ac Audio device: Intel Corporation N10/ICH 7
>>> Family High Definition Audio Controller
>>>
>>> Modem interrupt assignment and sharing:
>>> 45: 1004 0 PCI-MSI-edge hda_intel
>>> --- Bootup diagnostics for card in PCI slot 00:1b.0 ----
>>> [ 0.284217] pci 0000:00:1b.0: reg 10: [mem 0xe4700000-0xe4703fff 64bit]
>>> [ 0.284281] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
>>> [ 0.284286] pci 0000:00:1b.0: PME# disabled
>>> [ 18.824476] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
>>> [ 18.824512] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
>>> [ 18.824522] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level,
>>> low) -> IRQ 16
>>> [ 18.824602] HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X
>>> [ 18.824636] HDA Intel 0000:00:1b.0: setting latency timer to 64
>>>
>>> The PCI slot 00:1b.0 of the modem card may be disabled early in
>>> a bootup process, but then enabled later. If modem drivers load
>>> but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
>>> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
>>> if help is needed.
>>>
>>>
>>> === Finished firmware and bootup diagnostics, next deducing cogent software. ===
>>>
>>> Predictive diagnostics for card in bus 02:06.4:
>>> Modem chipset detected on
>>> NAME="Communication controller: Texas Instruments PCIxx12 GemCore
>>> based SmartCard controller"
>>> CLASS=0780
>>> PCIDEV=104c:803d
>>> SUBSYS=103c:30ac
>>> IRQ=11
>>> HDA2=00:1b.0
>>> HDAchipVendorID=11c1
>>> CHIP=0x11c13026
>>> IDENT=slmodemd
>>> SLMODEMD_DEVICE=hw:0,6
>>> Driver=snd-hda-intel
>>> package=agrsm-11c11040
>>>
>>> For candidate modem in: 02:06.4
>>> 0780 Communication controller: Texas Instruments PCIxx12 GemCore
>>> based SmartCard controller
>>> Primary device ID: 104c:803d
>>> Support type needed or chipset: slmodemd
>>>
>>>
>>> An ALSA (Advanced Linux Sound Architecture) modem driver: snd-hda-intel
>>> provides Low Level support enabling contact with the modem hardware.
>>> For all BUT Conexant chip soft modems (using hsfmodem software)
>>> complementary High Level support is through a Smartlink utility: slmodemd
>>>
>>> Download from http://linmodems.technion.ac.il/packages/smartlink/
>>> the package SLMODEMD_gcc4.4_alsa1.0.23.tar.gz having a compiled
>>> slmodemd. Unpack under Linux with:
>>> $ tar zxf SLMODEMD_gcc4.4_alsa1.0.23.tar.gz
>>> and read instructions therein. But briefly, the modem is setup with command:
>>> sudo slmodemd -c YOUR_COUNTRY --alsa hw:0,6
>>> reporting dynamic creation of ports:
>>> /dev/ttySL0 --> /dev/pts/N , with N some number
>>> Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow
>>> through guidance.
>>>
>>>
>>> Writing DOCs/Intel.txt
>>> Writing DOCs/Smartlink.txt
>>> ============ end Smartlink section =====================
>>>
>>> The AgereSystems/LSI agrsm code supports compiling of a agrmodem +
>>> agrserial driver pair.
>>> There are a few different chipsets which use this driver pair, but
>>> they use different code resources:
>>> Chipsets KV* PackageNames (most current as of November 2009)
>>> ----------------------------------------------------------------------------------------------
>>> 11c1:048c and 11c1:048f
>>> 2.6.29 agrsm048pci-2.1.60_20100108_i386.deb or
>>> agrsm048pci-2.1.60_20100108.tar.gz
>>> 11c1:0620 2.6.31
>>> agrsm06pci-2.1.80_20100106_i386.deb or
>>> agrsm06pci-2.1.80~20100106.tar.gz !!
>>> 11c11040 (on HDA audio cards) 2.6.31
>>> agrsm-11c11040_20091225_i386.deb or
>>> agrsm-11c11040-2.1.80~20091225.tar.bz2 !!
>>> All available at:
>>> http://linmodems.technion.ac.il/packages/ltmodem/11c11040/
>>> Additionally there are;
>>> automation & testing agrsm-tools_0.0.1_all.deb or
>>> agrsm-tools-0.0.1-2.noarch.rpm
>>> General background agrsm_howto.txt
>>> ------------------------------------------------------------------------------------------------
>>> * KV == latest kernel release with a reported success
>>> !! Latest update with major credit to Nikolay Zhuravlev
>>> But see conflict issue:
>>> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg02753.html
>>> For the 11c11040 chip with kernels 2.6.31 and later a change in a
>>> modules loading settingmay be necessary.
>>> Within the file /etc/modprobe.d/alsa-base.conf (or equivalent for
>>> your Distro), change the phrase:
>>> options snd-hda-intel power_save=10
>>> to:
>>> options snd-hda-intel power_save=0
>>> or the agrsm drivers will not function. For Ubuntu related systems
>>> this can be done with:
>>> $ sudo gedit /etc/modprobe.d/alsa-base.conf
>>>
>>> Report from Bjorn Wielens:
>>> Please note- trying to load the modules on a OpenSuSE 11.2 system gives
>>> an error about the module_version symbol. Using:
>>> # modprobe --force agrmodem
>>> # modprobe --force agrserial
>>> is necessary to load the drivers, and does not appear to cause ill effects.
>>>
>>>
>>> All of the above packages are dkms competent. This means that if your
>>> Linux distros dkms package
>>> is previously installed, if provides for future updates matching
>>> forthcoming kernels.
>>>
>>> -------------- end Agere Systems section -------------------
>>>
>>>
>>> Predictive diagnostics for card in bus 00:1b.0:
>>> Modem chipset not detected on
>>> NAME="Audio device: Intel Corporation N10/ICH 7 Family High Definition
>>> Audio Controller "
>>> CLASS=0403
>>> PCIDEV=8086:27d8
>>> SUBSYS=103c:30ac
>>> IRQ=45
>>>
>>> For candidate modem in: 00:1b.0
>>> 0403 Audio device: Intel Corporation N10/ICH 7 Family High
>>> Definition Audio Controller
>>> Primary device ID: 8086:27d8
>>> Support type needed or chipset:
>>>
>>>
>>> Completed candidate modem analyses.
>>>
>>> The base of the UDEV device file system is: /dev/.udev
>>>
>>> Versions adequately match for the compiler installed: 4.4.5
>>> and the compiler used in kernel assembly: 4.4.5
>>>
>>> linux-headers-2.6.35-25-generic resources needed for compiling are
>>> not manifestly ready!
>>>
>>> If compiling is necessary packages must be installed, providing:
>>> linux-headers-2.6.35-25-generic
>>>
>>>
>>> If a driver compilation fails, with message including some lack of
>>> some FileName.h (stdio.h for example), then
>>> Some additional kernel-header files need installation to /usr/include.
>>> The minimal additional packages are libc6-dev
>>> and any of its dependents, under Ubuntu linux-libc-dev
>>>
>>> If an alternate ethernet connection is available,
>>> $ apt-get update
>>> $ apt-get -s install linux-kernel-devel
>>> will install needed packages.
>>> For Debian/Ubuntu related distributions, run the following command to
>>> display the needed package list:
>>>
>>> Otherwise packages have to be found through http://packages.ubuntu.com
>>> Once downloaded and transferred into a Linux partition,
>>> they can be installed alltogether with:
>>> $ sudo dpkg -i *.deb
>>>
>>>
>>> Checking pppd properties:
>>> -rwsr-xr-- 1 root dip 273248 2010-07-09 11:41 /usr/sbin/pppd
>>>
>>> In case of an "error 17" "serial loopback" problem, see:
>>> http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
>>>
>>> To enable dialout without Root permission do:
>>> $ su - root (not for Ubuntu)
>>> sudo chmod a+x /usr/sbin/pppd
>>> or under Ubuntu related Linuxes
>>> sudo chmod a+x /usr/sbin/pppd
>>>
>>> Checking settings of: /etc/ppp/options
>>> asyncmap 0
>>> noauth
>>> crtscts
>>> lock
>>> hide-password
>>> modem
>>> proxyarp
>>> lcp-echo-interval 30
>>> lcp-echo-failure 4
>>> noipx
>>>
>>> In case of a message like:
>>> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
>>> see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
>>>
>>> For guidance on FAX usage, get from
>>> http://linmodems.technion.ac.il/packages/ get faxing.tar.gz
>>> It has samples for a modem using port /dev/ttySL0, which must be
>>> changed to match your modem's port.
>>>
>>> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 eth2
>>> Which can interfere with Browser naviagation.
>>>
>>> Don't worry about the following, it is for experts should trouble
>>> shooting be necessary.
>>> ==========================================================
>>>
>>> Checking for modem support lines:
>>> --------------------------------------
>>> /device/modem symbolic link: lrwxrwxrwx 1 root root 6
>>> 2011-01-23 02:10 /dev/modem -> ttySL0
>>> slmodemd created symbolic link /dev/ttySL0:
>>> Within /etc/udev/ files:
>>>
>>> Within /etc/modprobe.conf files:
>>> /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
>>> /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
>>> /etc/modprobe.d/sl-modem.conf:install slamr /sbin/modprobe -qb
>>> ungrab-winmodem; /sbin/modprobe --ignore-install slamr; test -e
>>> /dev/slamr0 && (chmod 660 /dev/slamr0 && chgrp dialout /dev/slamr0) ||
>>> (/bin/mknod -m 660 /dev/slamr0 c 242 0 2>/dev/null && chgrp dialout
>>> /dev/slamr0)
>>> /etc/modprobe.d/sl-modem.conf:install slusb /sbin/modprobe -qb
>>> ungrab-winmodem; /sbin/modprobe --ignore-install slusb; test -e
>>> /dev/slusb0 && (chmod 660 /dev/slusb0 && chgrp dialout /dev/slusb0) ||
>>> (/bin/mknod -m 660 /dev/slusb0 c 243 0 2>/dev/null && chgrp dialout
>>> /dev/slusb0)
>>> /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in
>>> order to blacklist unwanted modem drivers
>>> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
>>> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
>>> Within any ancient /etc/devfs files:
>>>
>>> Within ancient kernel 2.4.n /etc/module.conf files:
>>>
>>> --------- end modem support lines --------
>>>
>>>
>>> --
>>> $0='!/msfQ0yjoV!fe!sfldbi!psup!pmpT'x19xor print+map{("\e[7m \e[0m",
>>> chr ord(chop$0)-1)[$_].("\n")[++$i%72]}split//,unpack'B*',pack'H*',(
>>> $P='F'x18)."8186078739E1F0F0E19FCF333319CCE6667383CF0733099E67E7F39"
>>> ."FCF3333218067E7F39FCF3333319E6666739F860787399E70F0E1$P"#Perl rulz
>>>
>>
>
>
>
> --
> $0='!/msfQ0yjoV!fe!sfldbi!psup!pmpT'x19xor print+map{("\e[7m \e[0m",
> chr ord(chop$0)-1)[$_].("\n")[++$i%72]}split//,unpack'B*',pack'H*',(
> $P='F'x18)."8186078739E1F0F0E19FCF333319CCE6667383CF0733099E67E7F39"
> ."FCF3333218067E7F39FCF3333319E6666739F860787399E70F0E1$P"#Perl rulz
>
