I am pasting the output of dmesg. According to usb_modeswitch forum
the usb cdma device that i have doesn't need switching. So, I would
like to know the steps how to set up the usb modem. "sudo wvdialconf
"doesn't detect the modem. What are the additional commands required
to setup usb modem, please advise. Hoping for your reply.
[ 31.765658] usbcore: registered new interface driver usbserial
[ 31.765683] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/serial/usb-s
erial.c: USB Serial support registered for generic
[ 31.765708] usbcore: registered new interface driver usbserial_generic
[ 31.765712] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/serial/usb-s
erial.c: USB Serial Driver core
[ 31.810278] Adding 1003988k swap on /dev/sda6. Priority:-1 extents:1 across:
1003988k
[ 57.500544] EXT3 FS on sda7, internal journal
[ 58.494266] No dock devices found.
[ 58.628902] input: Power Button (FF) as /class/input/input4
[ 58.628931] ACPI: Power Button (FF) [PWRF]
[ 58.629064] input: Power Button (CM) as /class/input/input5
[ 58.629090] ACPI: Power Button (CM) [PWRB]
[ 59.639882] ppdev: user-space parallel port driver
[ 59.703116] r8169: eth0: link down
[ 59.903251] audit(1283886765.923:3): type=1503 operation="inode_permission"
requested_mask="a" denied_mask="a" name="/dev/tty" pid=4860 profile="/usr/sbin/c
upsd"
[ 60.144178] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 60.144189] apm: disabled - APM is not SMP safe.
[ 61.107942] Failure registering capabilities with primary security module.
[ 61.208486] [drm] Initialized drm 1.1.0 20060810
[ 61.211184] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level,
low) -> IRQ
16
[ 61.211688] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 61.213441] set status page addr 0x00033000
[ 61.423927] Bluetooth: Core ver 2.11
[ 61.424090] NET: Registered protocol family 31
[ 61.424094] Bluetooth: HCI device and connection manager initialized
[ 61.424099] Bluetooth: HCI socket layer initialized
[ 61.452522] Bluetooth: L2CAP ver 2.8
[ 61.452529] Bluetooth: L2CAP socket layer initialized
[ 61.523329] Bluetooth: RFCOMM socket layer initialized
[ 61.523462] Bluetooth: RFCOMM TTY layer initialized
[ 61.523467] Bluetooth: RFCOMM ver 1.8
[ 111.225678] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 111.388355] usb 3-1: configuration #1 chosen from 1 choice
[ 111.391315] usbserial_generic 3-1:1.0: generic converter detected
[ 111.391637] usb 3-1: generic converter now attached to ttyUSB0
[ 111.450950] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/serial/usb-s
erial.c:
USB Serial support registered for pl2303
[ 111.451465] usbcore: registered new interface driver pl2303
[ 111.451472] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/serial/pl230
3.c:
Prolific PL2303 USB to serial adaptor driver
nitin@nitin:~$
