Cher Frederic!
Needless to day that all of us are exceedingly happy that you brought
your modem to that stage.
Let me however remark that whay you have shown is is a configuration
menu which sends commands to the modem.
The way is often long and painful to bring the mode to understand what
you says to it and behave accordingly.
Thus I must ask a nasty question: have you succeeded in making a remote
modem ring, answer, synchronize, and finally print some text.
I apologize for this cold shower, but for 10 years we have seen scores
of users not understanding that a panel like the one you showed sends
commands to the air, rather than to the modem hardware.
You may well have achieved much more, but the screen shot sent to us
means very little about success.
Sorry
Jacques
On 08/15/2010 02:09 PM, Frederic28 wrote:
Hi,
My winmodem support FAx! Yes, it does
Look at image attached.
So,
I ran step by step like you wrote.
... my first step, before request some help was to install the deb
package with the deb installer tools ! (apt-get)
so, there are some differences on theses steps
The tool wvdialconf is not on my system, do I need it ? for run fax ?
so here is the screen copy I got :
frederic@CPQ2800:~/Téléchargements$ sudo dpkg -i agrsm*.deb
[sudo] password for frederic:
(Lecture de la base de données... 194990 fichiers et répertoires déjà
installés.)
Préparation du remplacement de agrsm048pci-2.1.60 20100108 (en utilisant
agrsm048pci-2.1.60_20100108_i386.deb) ...
-------- Uninstall Beginning --------
Module: agrsm048pci
Version: 2.1.60
Kernel: 2.6.32-24-generic (i686)
-------------------------------------
Status: Before uninstall, this module version was ACTIVE on this kernel.
agrmodem.ko:
- Uninstallation
- Deleting from: /lib/modules/2.6.32-24-generic/updates/dkms/
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module
version.
agrserial.ko:
- Uninstallation
- Deleting from: /lib/modules/2.6.32-24-generic/updates/dkms/
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module
version.
depmod....
DKMS: uninstall Completed.
------------------------------
Deleting module version: 2.1.60
completely from the DKMS tree.
------------------------------
Done.
The dkms driver autocompiling package is installed.
The drivers source code is being installed to the folder /usr/src/
Then the drivers will be compiled and installed by the dkms tool
provided that your System has adequate compiling support.
Following kernel upgrades, complementary drivers will be
automatically compiled and installed.
Supported 11c1:048c modem chipset found.
Dépaquetage de la mise à jour de agrsm048pci-2.1.60 ...
Sélection du paquet agrsm-tools précédemment désélectionné.
Dépaquetage de agrsm-tools (à partir de agrsm-tools_0.0.1_all.deb) ...
Paramétrage de agrsm048pci-2.1.60 (20100108) ...
Creating symlink /var/lib/dkms/agrsm048pci/2.1.60/source ->
/usr/src/agrsm048pci-2.1.60
DKMS: add Completed.
Kernel preparation unnecessary for this kernel. Skipping...
Building module:
cleaning build area....
make KERNELRELEASE=2.6.32-24-generic
-C /lib/modules/2.6.32-24-generic/build
M=/var/lib/dkms/agrsm048pci/2.1.60/build.....
cleaning build area....
DKMS: build Completed.
agrmodem.ko:
Running module version sanity check.
- Original module
- Installation
- Installing to /lib/modules/2.6.32-24-generic/updates/dkms/
agrserial.ko:
Running module version sanity check.
- Original module
- Installation
- Installing to /lib/modules/2.6.32-24-generic/updates/dkms/
depmod....
DKMS: install Completed.
Paramétrage de agrsm-tools (0.0.1) ...
For a first functional test, run:
sudo agrsm-test
frederic@CPQ2800:~/Téléchargements$ sudo agrsm-test
Found drivers for boot kernel 2.6.32-24-generic at:
/lib/modules/2.6.32-24-generic/updates/dkms/agrserial.ko
/lib/modules/2.6.32-24-generic/updates/dkms/agrmodem.ko
/lib/modules/2.6.32-24-generic/extra/agrserial.ko
/lib/modules/2.6.32-24-generic/extra/agrmodem.ko
Loading drivers:
Drivers loaded:
agrserial 9273 0
agrmodem 1183595 1 agrserial
and symbolic link created:
lrwxrwxrwx 1 root root 12 2010-08-15 13:03 /dev/ttySAGR -> /dev/ttyAGS3
Checking for utility wvdialconf
Utility wvdialconf not found
The installation record has been written to ./agrsm-test.txt
-------- Message initial --------
De: Marvin Stodolsky<marvin.stodolsky@xxxxxxxxx>
À: Frederic28<frederic28@xxxxxxxxx>
Cc: discuss@xxxxxxxxxxxxx
Sujet: Re: [Fwd: Frederic, France, YourCountry kernel 2.6.32-24-generic]
Date: Fri, 13 Aug 2010 20:55:35 -0400
Frederic,
I'm doubtful that either of your winmodems will support fax.
But if you want to merely do dialout, there easiest route is to
install the packages
11c1:048c and 11c1:048f 2.6.29
agrsm048pci-2.1.60_20100108_i386.deb l available at:
http://linmodems.technion.ac.il/packages/ltmodem/11c11040/
Additionally there are;
automation& testing agrsm-tools_0.0.1_all.deb
General background agrsm_howto.txt
Install the packages with:
$ sudo dpkg -i agrsm*.deb
MarvS
On Fri, Aug 13, 2010 at 10:32 AM, Frederic28<frederic28@xxxxxxxxx> wrote:
Hi
I would like make my FAX run.
But, I have trouble for install the drivers.
Here below the log from scanModem.
Hope I done as I should :-) BORDER=0>
Thanks.
-------------------------- System information
----------------------------
CPU=i686, Ubuntu , ALSA_version=1.0.21
Linux version 2.6.32-24-generic (buildd@rothera) (gcc version 4.4.3
(Ubuntu 4.4.3-4ubuntu5) ) #39-Ubuntu SMP Wed Jul 28 06:07:29 UTC 2010
scanModem update of: 2010_05_29
Distrib_ID=Ubuntu
DistribCodeName=lucid
The dkms driver upgrade utilities are installed,
There are no blacklisted modem drivers in /etc/modprobe* files
Potentially useful modem drivers now loaded are:
snd_via82xx_modem
Attached USB devices are:
ID 046d:c045 Logitech, Inc. Optical Mouse
ID 046d:08a9 Logitech, Inc. Notebook Deluxe
If a cellphone is not detected, see
http://ubuntuforums.org/archive/index.php/t-878554.html
A sample report is:
http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@xxxxxxxxxxxxx
Candidate PCI devices with modem chips are:
00:0a.0 Communication controller: Agere Systems V.92 56K WinModem (rev
03)
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem
Controller (rev 80)
High Definition Audio cards can host modem chips.
For candidate card in slot 00:0a.0, firmware information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:0a.0 11c1:048c 11c1:044c Communication controller: Agere Systems V.92
56K WinModem
Modem interrupt assignment and sharing:
15: 0 IO-APIC-edge pata_via
--- Bootup diagnostics for card in PCI slot 00:0a.0 ----
[ 0.146761] pci 0000:00:0a.0: reg 10 32bit mmio:
[0xe6000000-0xe60000ff]
[ 0.146768] pci 0000:00:0a.0: reg 14 io port: [0xa000-0xa007]
[ 0.146775] pci 0000:00:0a.0: reg 18 io port: [0xa400-0xa4ff]
[ 0.146804] pci 0000:00:0a.0: supports D2
[ 0.146807] pci 0000:00:0a.0: PME# supported from D2 D3hot D3cold
[ 0.146812] pci 0000:00:0a.0: PME# disabled
The PCI slot 00:0a.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible
fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
For candidate card in slot 00:11.6, firmware information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:11.6 1106:3068 Communication controller: VIA Technologies, Inc. AC'97
Modem Controller
Modem interrupt assignment and sharing:
22: 106 IO-APIC-fasteoi VIA8237
--- Bootup diagnostics for card in PCI slot 00:11.6 ----
[ 0.147580] pci 0000:00:11.6: reg 10 io port: [0xdc00-0xdcff]
[ 7.822919] VIA 82xx Modem 0000:00:11.6: enabling device (0000 ->
0001)
[ 7.823394] VIA 82xx Modem 0000:00:11.6: PCI INT C -> Link[ALKC] ->
GSI 22 (level, low) -> IRQ 22
[ 8.572052] VIA 82xx Modem 0000:00:11.6: setting latency timer to 64
[ 9.076291] VIA 82xx Modem 0000:00:11.6: PCI INT C disabled
[ 9.076319] VIA 82xx Modem: probe of 0000:00:11.6 failed with error
-13
The PCI slot 00:11.6 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible
fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
PCIbus=00:11.6
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem
Controller (rev 80)
Flags: medium devsel, IRQ 22
I/O ports at dc00 [size=256]
Capabilities: [d0] Power Management version 2
Kernel modules: snd-via82xx-modem
===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
The ALSA packages provide audio support and also drivers for some
modems.
ALSA diagnostics are written during bootup to /proc/asound/ folders.
The modem cards detected by "aplay -l" are: None
The /proc/asound/pcm file reports:
-----------------------
00-00: VIA 8237 : VIA 8237 : playback 4 : capture 1
00-01: VIA 8237 : VIA 8237 : playback 1 : capture 1
01-00: USB Audio : USB Audio : capture 1
about /proc/asound/cards:
------------------------
0 [V8237 ]: VIA8237 - VIA 8237
VIA 8237 with ALC658D at 0xd800, irq 22
1 [default ]: USB-Audio - Camera
Camera at usb-0000:00:10.1-1, full speed
=== Finished firmware and bootup diagnostics, next deducing cogent
software. ===
Predictive diagnostics for card in bus 00:0a.0:
Modem chipset detected on
NAME="Communication controller: Agere Systems V.92 56K WinModem "
CLASS=0780
PCIDEV=11c1:048c
SUBSYS=11c1:044c
IRQ=5
IDENT=agrsm
For candidate modem in: 00:0a.0
0780 Communication controller: Agere Systems V.92 56K WinModem
Primary device ID: 11c1:048c
Support type needed or chipset: agrsm
The AgereSystems/LSI agrsm code supports compiling of a agrmodem +
agrserial driver pair.
There are a few different chipsets which use this driver pair, but they
use different code resources:
Chipsets KV* PackageNames (most current as of November 2009)
----------------------------------------------------------------------------------------------
11c1:048c and 11c1:048f 2.6.29
agrsm048pci-2.1.60_20100108_i386.deb or
agrsm048pci-2.1.60_20100108.tar.gz
11c1:0620 2.6.31
agrsm06pci-2.1.80_20100106_i386.deb or
agrsm06pci-2.1.80~20100106.tar.gz !!
11c11040 (on HDA audio cards) 2.6.31 agrsm-11c11040_20091225_i386.deb
or agrsm-11c11040-2.1.80~20091225.tar.bz2 !!
All available at:
http://linmodems.technion.ac.il/packages/ltmodem/11c11040/
Additionally there are;
automation& testing agrsm-tools_0.0.1_all.deb or
agrsm-tools-0.0.1-2.noarch.rpm
General background agrsm_howto.txt
------------------------------------------------------------------------------------------------
* KV == latest kernel release with a reported success
!! Latest update with major credit to Nikolay Zhuravlev
But see conflict issue:
http://linmodems.technion.ac.il/bigarch/archive-nineth/msg02753.html
For the 11c11040 chip with kernels 2.6.31 and later a change in a
modules loading settingmay be necessary.
Within the file /etc/modprobe.d/alsa-base.conf (or equivalent for
your Distro), change the phrase:
options snd-hda-intel power_save=10
to:
options snd-hda-intel power_save=0
or the agrsm drivers will not function. For Ubuntu related systems
this can be done with:
$ sudo gedit /etc/modprobe.d/alsa-base.conf
Report from Bjorn Wielens:
Please note- trying to load the modules on a OpenSuSE 11.2 system gives
an error about the module_version symbol. Using:
# modprobe --force agrmodem
# modprobe --force agrserial
is necessary to load the drivers, and does not appear to cause ill
effects.
All of the above packages are dkms competent. This means that if your
Linux distros dkms package
is previously installed, if provides for future updates matching
forthcoming kernels.
-------------- end Agere Systems section -------------------
