Brian, scanModem reports that your modem would need hsfmodem drivers from linuxant: Download a package like hsfmodem-7.68.00.12full.tar.gz package but for x86_64 bit: Get the following package http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.80.02.06x86_64full/hsfmodem-7.80.02.06x86_64full-1.x86_64.rpm.zip and run $ su - passwd: # rpm -Uvh hsfmodem-7.80* and try to follow the instructions METHOD A: BINARY RPM PACKAGE (*.{arch}.rpm) If you have obtained the driver package in RPM format: 1. install the rpm with "rpm -i hsfmodem-{version}.{arch}.rpm" 2. if necessary, run "hsfconfig" to complete the installation, enter license information, or to change your modem's configuration. If you need to rebuild the generic RPM from source, you can get the TAR package and run: "rpmbuild -tb hsfmodem-{version}.tar.gz" (if rpmbuild is not found, you might have to install the rpm-build package or if you have an older RPM version, try "rpm --rebuild ..."). If you want a pre-compiled package for the currently running kernel, you can try "make rpmprecomp" in the top directory. as provided in http://www.linuxant.com/drivers/hsf/install.php /* Predictive diagnostics for card in bus 02:00.0: Modem chipset detected on NAME="Communication controller: Conexant Systems, Inc. Conexant SoftK56 Data/Fax Modem " CLASS=0780 PCIDEV=14f1:2f50 SUBSYS=14f1:205f IRQ=21 HDA2=00:1b.0 IDENT=hsfmodem Driver=hsfmodem-drivers For candidate modem in: 02:00.0 0780 Communication controller: Conexant Systems, Inc. Conexant SoftK56 Data/Fax Modem Primary device ID: 14f1:2f50 Support type needed or chipset: hsfmodem For owners of a Dell PCs with Conexant HSF modems, a driver source package with full speed enabled is available, but requires driver compiling. Read DOCs/Conexant.txt Support for the 14f1:2f50 and 14f1:2215 HSF modems is projected early in 2007 from Linuxant. For all code packages from Linuxant.com, either a driver set matching the boot kernel will be installed, or the drivers will first be compiled and then installed. The expert on modem software for Linux is "Support (Jonathan)" <modem.support@xxxxxxxxxxxx> Start at http://www.linuxant.com/drivers/hsf/full for eventually download of a hsfmodem-7.68.00.12full_k.???.zip package with ??? the package type (deb, rpm, tar etc) These packages have compiled drivers but will also compile a driver, if there is a mismatch between the resident kernel and provided driver. The generic hsfmodem-7.68.00.12full.tar.gz package only provides compiling support Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the hsfmodem package matching your System. For several Linux distros, there are precompiled drivers matched to specific kernels. These have within the FileName, your KernelVersion: 2.6.33.3_85.fc13.x86_64 They can be found through http://www.linuxant.com/drivers/hsf/full/downloads.php A more precise location may be given a few paragraphs below. If an EXACT Match with your your KernelVersion is not found, the needed drivers will be auto compiled anyway. Alternatively, one of the "Generic packages with source" near the bottom of the page must be used. Downloaded packages must be moved into the Linux partition (home folder is OK) and unzipped with: unzip hsf*.zip The installation command for a .deb suffic packages is, with root/adm permission: dpkg -i hsf*.deb while for .rpm suffix it is, with: rpm -i hsf*.rpm Read DOCs/Conexant.txt Writing DOCs/Conexant.txt Completed candidate modem analyses. The base of the UDEV device file system is: /dev/.udev Versions adequately match for the compiler installed: 4.4.4 and the compiler used in kernel assembly: 4.4.4 linux-headers-2.6.33.3-85.fc13.x86_64 resources needed for compiling are not manifestly ready! If compiling is necessary packages must be installed, providing: */ Regards, Antonio On 8/2/10, it@xxxxxxxxxxxx <it@xxxxxxxxxxxx> wrote: > Hi, > > I've had a PCI internal modem + fax card. I run it properly in Windows > XP, and now I move to Fedora Core 12. Attached is the ModemData.txt > and the a snapshot of my model card's box. > > May you please tell me where I can download the full verison (with fax > function) driver for this hardware for Linux Fedora Core 12? Thanks. > > Cheers, > > Brian > >
