Good morning everybody, I have tried a lot but I can not make linux
enable PCI interrupts for my Smartlink sl2800.
I was thinking of buying another one. I gone to the store and they have
an Encore Internal PCI modem the model is ENF656-ESW-COPR. I was reading
some information, and it seems it comes with a Conexant chip, but before
I buy it I would like to hear the opinion of somebody with a similar
experience.
Also saw other models: ENF656-ESW-MOPR and ENF656-ESW-AGPR. The first
one seems to come with a Motorola chip and the second one I think comes
with an Agere chip.
I read about some bad experiences with Deborah Agere chip, so I think
that model would be discarded. What do you think?
Cristian Iturri
El 29/06/10 09:38, Cristian Iturri escribió:
Good morning everybody, starting a new day in Argentina, I'm still
fighting against the SmartLink SL2800.
Thanks Antonio for the support.
Today I'll gonna play with the BIOS (again) to see if I'm not
forgetting something.
Regards.
Cristian
El 28/06/10 16:38, Antonio Olivares escribió:
Cristian,
Sorry for late reply, but have you checked BIOS settings?
Change PCI to nonPlug&Play OS or something like that?
Regards,
Antonio
On Mon, Jun 28, 2010 at 12:21 PM, Cristian
Iturri<cristian@xxxxxxxxxxx> wrote:
I've changed the modem card to another PCI slot so now the pci
device is
0000:04:00.0 wich still have its PCI interrupt disabled.
I don't know what to do
El 28/06/10 13:49, Cristian Iturri escribió:
I've compiled and installed both the ungrab-winmodem-20090716 and the
slmodem-2.9.11-20080126
then I've ran these commands:
# modprobe ungrab-winmodem
# tail /var/log/messages
Jun 28 12:37:00 pbx saslauthd[2590]: detach_tty : master pid is: 2590
Jun 28 12:37:00 pbx saslauthd[2590]: ipc_init : listening on socket:
/var/run/saslauthd/mux
Jun 28 12:40:07 pbx ntpd[2117]: synchronized to LOCAL(0), stratum 10
Jun 28 12:40:07 pbx ntpd[2117]: kernel time sync enabled 0001
Jun 28 12:44:24 pbx ntpd[2117]: synchronized to 200.80.32.170,
stratum 3
Jun 28 12:47:39 pbx kernel: ACPI: PCI interrupt for device
0000:04:01.0
disabled
Jun 28 13:02:36 pbx ntpd[2117]: synchronized to 200.11.116.1,
stratum 2
Jun 28 13:10:18 pbx ntpd[2117]: time reset +0.224818 s
Jun 28 13:13:35 pbx ntpd[2117]: synchronized to LOCAL(0), stratum 10
Jun 28 13:15:45 pbx ntpd[2117]: synchronized to 200.11.116.1,
stratum 2
# modprobe slamr
# tail /var/log/messages
Jun 28 13:10:18 pbx ntpd[2117]: time reset +0.224818 s
Jun 28 13:13:35 pbx ntpd[2117]: synchronized to LOCAL(0), stratum 10
Jun 28 13:15:45 pbx ntpd[2117]: synchronized to 200.11.116.1,
stratum 2
Jun 28 13:29:30 pbx kernel: slamr: SmartLink AMRMO modem.
Jun 28 13:29:30 pbx kernel: slamr: probe 2000:2800 �\$ ������t$ �|$
�� ��G
0 card...
Jun 28 13:29:30 pbx kernel: PCI: Enabling device 0000:04:01.0 (0000 ->
0002)
Jun 28 13:29:30 pbx kernel: ACPI: PCI Interrupt 0000:04:01.0[A] ->
GSI 16
(level, low) -> IRQ 169
Jun 28 13:29:30 pbx kernel: slamr: cannot create card.
Jun 28 13:29:30 pbx kernel: ACPI: PCI interrupt for device
0000:04:01.0
disabled
Jun 28 13:29:30 pbx kernel: slamr: probe of 0000:04:01.0 failed
with error
-12
# slmodemd -c ARGENTINA /dev/slamr0
error: mdm setup: cannot open dev `/dev/slamr0': No such device
error: cannot setup device `/dev/slamr0'
It seems like the pci interrupt for the modem is disabled, I've tried
starting CentOS with pci=routeirq and that just hang up the PC,
then I've
tried pollirq and nothing happens.
Can somebody help me with that?
