George,
You seem to have an extra "m" in the /dev/modem link.
Try: ln -sf /dev/ttySAGR /dev/modem
Good luck.
-Yair
On Wed, Mar 10, 2010 at 8:16 AM, George H <george.dma@xxxxxxxxx> wrote:
> Hi Marvin,
>
> Thanks for your reply.
>
>> In the agrsm06pci-2.1.80~20100106/agrsoftmodem.c
>> file there are indeed recognition lines for your 047e:2892 chip set in
>> { USB_DEVICE(USB_USS_VENDOR_ID, USB_USS_PRODUCT_ID_2828) },
>> { USB_DEVICE(USB_USS_VENDOR_ID, USB_USS_PRODUCT_ID_2892
>
> That's right, and I am confused as to why it still does not work.
>
>> Using the AgereMdmDaemon is sometimes troublesome. Set a symbolic link:
>> $ sudo modprobe /dev/ttySAGR /dev/ttyAGS3
>> and check if the modem is detected by:
>> $ sudo wvdial
>
> Please see the script below of all the commands i've executed. I hope
> it helps to explain what it is I am getting.
>
> Script started on Wed Mar 10 05:54:10 2010
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 #./agr_softmodem start
> Starting Agere Soft Modem
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # lsmod
> Module Size Used by
> agrserial 10096 0
> agrmodem 1331844 1
> fglrx 1947356 28
> intel_agp 22932 0
> agpgart 26564 2 fglrx,intel_agp
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # tail /var/log/kern.log
> Mar 10 05:54:21 toshi kernel: * Hello Agere Driver PCIe **
> Mar 10 05:54:21 toshi kernel: Loading module Agere Modem Controller
> driver version 2.1.80-Red Flag NE 5.0 (2007-10-1)
> Mar 10 05:54:21 toshi kernel: ttyAGS3 at I/O 0x400 (irq = 3) is a AgereModem
> Mar 10 05:54:21 toshi kernel: Loading module Agere Modem Interface
> driver version 2.1.80.0Red Flag 5.0 NE (2007-10-01)
> Mar 10 05:54:21 toshi kernel: ==> codecType = 0x31
> Mar 10 05:54:21 toshi kernel: App PID = 5068
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # ln -s
> /dev/ttyAGS3 /dev/ttySAGR
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # ls -l /dev | grep AG
> lrwxrwxrwx 1 root root 12 Mar 10 05:54 mmodem -> /dev/ttyAGS3
> crw-rw---- 1 root uucp 62, 67 Mar 10 05:54 ttyAGS3
> lrwxrwxrwx 1 root root 12 Mar 10 05:55 ttySAGR -> /dev/ttyAGS3
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # cat/etc/serial.conf
> # These are the standard COM1 through COM4 devices
> #
> /dev/ttyS0 uart 16450 port 0x3F8 irq 4
> /dev/ttyS1 uart 16450 port 0x2F8 irq 3
> /dev/ttyS2 uart 16450 port 0x3E8 irq 4
> /dev/ttyS3 uart 16450 port 0x2E8 irq 3
> /dev/ttySAGR uart 16550A port 0x0400 irq 3
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # /etc/init.d/serial start
> * Setting /dev/ttyS0 to uart 16450 port 0x3F8 irq 4 ... ok
> * Setting /dev/ttyS1 to uart 16450 port 0x2F8 irq 3 ... ok
> * Setting /dev/ttyS2 to uart 16450 port 0x3E8 irq 4 ... ok
> * Setting /dev/ttyS3 to uart 16450 port 0x2E8 irq 3 ... ok
> * Setting /dev/ttySAGR to uart 16550A port 0x0400 irq 3 ... ok
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # wvdialconf
> /etc/wvdial.conf
> Editing `/etc/wvdial.conf'.
>
> Scanning your serial ports for a modem.
>
> Modem Port Scan<*1>: S0 S1 S2 S3
> ttySAGR<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> ttySAGR<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> ttySAGR<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>
>
> Sorry, no modem was detected! Is it in use by another program?
> Did you configure it properly with setserial?
>
> Please read the FAQ at http://open.nit.ca/wiki/?WvDial
>
> If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>.
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # wvdial
> --> WvDial: Internet dialer version 1.60
> --> Warning: section [Dialer Defaults] does not exist in wvdial.conf.
> --> Initializing modem.
> --> Sending: ATZ
> --> Sending: ATQ0
> --> Re-Sending: ATZ
> --> Modem not responding.
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # tail /var/log/kern.log
> Mar 10 06:00:50 toshi kernel: ==> codecType = 0x31
> Mar 10 06:01:06 toshi kernel: ttyS0: LSR safety check engaged!
> Mar 10 06:01:06 toshi kernel: ttyS1: LSR safety check engaged!
> Mar 10 06:01:06 toshi kernel: ttyS2: LSR safety check engaged!
> Mar 10 06:01:06 toshi kernel: ttyS3: LSR safety check engaged!
> Mar 10 06:01:06 toshi kernel: ==> codecType = 0x31
> Mar 10 06:01:11 toshi kernel: ==> codecType = 0x31
>
> root@toshi:~/bins/linmodem/agrsm06pci-2.1.80-20100106 # exit
>
> Script done on Wed Mar 10 06:01:32 2010
>
