Antonio,
scanModem reports that you need hsfmodem drivers:
For candidate modem in: 00:1b.0
0403 Audio device: Intel Corporation 82801I
Primary device ID: 8086:293e
Subsystem PCI_id 103c:360b
Softmodem codec or chipset from diagnostics:
from Archives:
Support type needed or chipset: hsfmodem
Writing DOCs/Intel.txt
For owners of a Dell PCs with Conexant HSF modems, a driver source
package with full speed enabled is available, but requires driver
compiling. Read DOCs/Conexant.txt
Start at http://www.linuxant.com/drivers/hsf/full for
eventually download of a hsfmodem-7.68.00.12full_k.???.zip package
with ??? the package type (deb, rpm, tar etc)
These packages have compiled drivers but will also compile a driver,
if there is a mismatch between the resident kernel and provided driver.
The generic hsfmodem-7.68.00.12full.tar.gz package only provides
compiling support
Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the
hsfmodem package matching your System. For several Linux distros, there are
precompiled drivers matched to specific kernels. These have within the FileName,
your KernelVersion: 2.6.25.5_1.1_default
They can be found through http://www.linuxant.com/drivers/hsf/full/downloads.php
A more precise location may be given a few paragraphs below.
If an EXACT Match with your your KernelVersion is not found, one of the
"Generic packages with source" near the bottom of the page must be used.
Downloaded packages must be moved into the Linux partition (home folder is OK)
and unzipped with:
unzip hsf*.zip
The installation command for a .deb suffic packages is, with root/adm
permission:
dpkg -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
Support for Conexant chips hosted on High Definition Audio cards may require
installation of additional packages, one of the alsa-driver-linuxant packages
on http://www.linuxant.com/alsa-driver/ At the same time download the
alsa-driver-1.0.17-1.patch , in case it prove to be later needed. During the
hsfmodem install, there will be a message if there is necessary installation of
alsa-driver-linuxant
The installation command for a .deb suffic packages is, with root/adm
permission:
dpkg -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
There may a message that "Dependencies" are not satisfied. In this
case the Ubuntu/Debian packages to be installed are linux-libc-dev &
libc6-dev. Package
names may be different for other Linuxes. If not on your install CD, these
packages can be searched for at http://packages.ubuntu.com. After download,
they can be coinstalled with:
dpkg -i li*.deb
Again try the alsa-driver-linuxant
There may be a message that the patch must be applied. In this case get the
ftp://ftp.alsa-project.org/pub/driver/alsa-driver-1.0.17.tar.bz2
Under Linux, this package is unpacked with:
$ tar jxf alsa*.tar.bz2
Next the patch is applied with:
$ patch -p0 < alsa-driver-1.0.17-1.patch
See http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html
for details on compiling and installing replacement snd-hda-intel + its
dependent drivers.
After the installation is completed, rerun the hsfmodem installation.
Reboot and try to detect the modem with Root permission:
wvdialconf /etc/wvdial.conf
Read DOCs/Conexant.txt
Regards,
Antonio
On Sun, Sep 13, 2009 at 3:31 PM, Antonio M Chimuzu
<achimuzu@xxxxxxxxxxxx> wrote:
> I followed instructions on how to get my modem to work.
> Please help
>
> --
> António Chimuzu
> Lecturer; FHSS - Africa University (www.africau.edu)
>
> Old Mutare site off Nyanga Road
> Mutare - P.O. Box 1320 - Zimbabwe
> Phone: +263 20 60026 / 60075 ext 277
> Cell: +263 912 902282 / +258 84 2317980
> Fax: +263 20 61785 (general fax line)
> email: chimuzua@xxxxxxxxxxxxx / achimuzu@xxxxxxxxxxxx
> www.chimuzu.googlepages.com
> IM: achimuzu@xxxxxxxxxxxx; Skype: chimuzu
>
> (\__/) People who want to share their religious
> (='.'=) visions and beliefs, usually
> ('')_('') dont want you to share yours with them
>
> Get OpenSUSE 11.1 - www.opensuse.org - May the Source be with you!
>
>
> Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server,
> as HTML can contain viruses. Use as the email Subject Line:
> YourName, YourCountry
> Welcome to openSUSE 11.0 (i586) - Kernel kernel 2.6.25.5-1.1-default
> With this Subject Line cogent experts will be alerted, and useful case names left in the Archive.
> YourCountry will enable Country specific guidance. Linux experts in YourCountry
> can be found through: http://www.linux.org/groups/index.html.
> They will know your Country's modem code, which may be essential for dialup service.
> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet Provider mail filters.
> So in a day, also check the Archived responses at http://www.linmodems.org
> -------------------------- System information ----------------------------
> CPU=i686,
> Welcome to openSUSE 11.0 (i586) - Kernel
> Linux version 2.6.25.5-1.1-default (geeko@buildhost) (gcc version 4.3.1 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) ) #1 SMP 2008-06-07 01:55:22 +0200
> scanModem update of: 2009_08_15
>
> There are no blacklisted modem drivers in /etc/modprobe* files
> Potentially useful modem drivers now loaded are:
> snd_hda_intel
>
> Attached USB devices are:
> ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
> ID 090c:f371 Feiya Technology Corp.
> ID 0bda:0158 Realtek Semiconductor Corp. Mass Stroage Device
> If a cellphone is not detected, see http://ubuntuforums.org/archive/index.php/t-878554.html
> A sample report is: http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
>
> If a USB modem or cellphone is attached and was not detected, please
> provide available information in your request to discuss@xxxxxxxxxxxxx
>
> For candidate card in slot 00:1b.0, firmware information and bootup diagnostics are:
> PCI slot PCI ID SubsystemID Name
> ---------- --------- --------- --------------
> 00:1b.0 8086:293e 103c:360b Audio device: Intel Corporation 82801I
>
> Modem interrupt assignment and sharing:
> 22: 3294 IO-APIC-fasteoi HDA Intel
> --- Bootup diagnostics for card in PCI slot 00:1b.0 ----
> ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
> PCI: Setting latency timer of device 0000:00:1b.0 to 64
>
>
> ===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
> The ALSA packages provide audio support and also drivers for some modems.
> ALSA diagnostics are written during bootup to /proc/asound/ folders.
>
> The ALSA verion is 1.0.16
> The modem cards detected by "aplay -l" are: None
>
>
> The /proc/asound/pcm file reports:
> -----------------------
> 00-01: Conexant Digital : Conexant Digital : playback 1
> 00-00: CONEXANT Analog : CONEXANT Analog : playback 1 : capture 1
>
> about /proc/asound/cards:
> ------------------------
> 0 [Intel ]: HDA-Intel - HDA Intel
> HDA Intel at 0x54700000 irq 22
>
> PCI slot 00:1b.0 has a High Definition Audio Card
> The drivers are in the kernel modules tree at:
> /lib/modules/2.6.25.5-1.1-default/kernel/sound/pci/hda/snd-hda-intel.ko
> UNEXPECTED HDA diagnostic outcome.
> === Finished firmware and bootup diagnostics, next deducing cogent software. ===
>
> Predictive diagnostics for card in bus 00:1b.0:
> Modem chipset detected on
> NAME="Audio device: Intel Corporation 82801I "
> CLASS=0403
> PCIDEV=8086:293e
> SUBSYS=103c:360b
> IRQ=22
> HDA=8086:293e
> SOFT=8086:293e.HDA
> IDENT=hsfmodem
> Driver=hsfmodem-drivers
>
> For candidate modem in: 00:1b.0
> 0403 Audio device: Intel Corporation 82801I
> Primary device ID: 8086:293e
> Subsystem PCI_id 103c:360b
> Softmodem codec or chipset from diagnostics:
> from Archives:
>
>
>
> Support type needed or chipset: hsfmodem
>
>
> Writing DOCs/Intel.txt
>
> For owners of a Dell PCs with Conexant HSF modems, a driver source package with full speed enabled is available, but requires driver compiling. Read DOCs/Conexant.txt
>
> Start at http://www.linuxant.com/drivers/hsf/full for
> eventually download of a hsfmodem-7.68.00.12full_k.???.zip package
> with ??? the package type (deb, rpm, tar etc)
> These packages have compiled drivers but will also compile a driver,
> if there is a mismatch between the resident kernel and provided driver.
> The generic hsfmodem-7.68.00.12full.tar.gz package only provides compiling support
>
>
> Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the
> hsfmodem package matching your System. For several Linux distros, there are
> precompiled drivers matched to specific kernels. These have within the FileName,
> your KernelVersion: 2.6.25.5_1.1_default
> They can be found through http://www.linuxant.com/drivers/hsf/full/downloads.php
> A more precise location may be given a few paragraphs below.
> If an EXACT Match with your your KernelVersion is not found, one of the
> "Generic packages with source" near the bottom of the page must be used.
> Downloaded packages must be moved into the Linux partition (home folder is OK)
> and unzipped with:
> unzip hsf*.zip
> The installation command for a .deb suffic packages is, with root/adm permission:
> dpkg -i hsf*.deb
> while for .rpm suffix it is, with:
> rpm -i hsf*.rpm
>
> Support for Conexant chips hosted on High Definition Audio cards may require
> installation of additional packages, one of the alsa-driver-linuxant packages
> on http://www.linuxant.com/alsa-driver/ At the same time download the
> alsa-driver-1.0.17-1.patch , in case it prove to be later needed. During the
> hsfmodem install, there will be a message if there is necessary installation of
> alsa-driver-linuxant
>
> The installation command for a .deb suffic packages is, with root/adm permission:
> dpkg -i hsf*.deb
> while for .rpm suffix it is, with:
> rpm -i hsf*.rpm
>
> There may a message that "Dependencies" are not satisfied. In this case the Ubuntu/Debian packages to be installed are linux-libc-dev & libc6-dev. Package
> names may be different for other Linuxes. If not on your install CD, these
> packages can be searched for at http://packages.ubuntu.com. After download,
> they can be coinstalled with:
> dpkg -i li*.deb
> Again try the alsa-driver-linuxant
>
> There may be a message that the patch must be applied. In this case get the
> ftp://ftp.alsa-project.org/pub/driver/alsa-driver-1.0.17.tar.bz2
> Under Linux, this package is unpacked with:
> $ tar jxf alsa*.tar.bz2
> Next the patch is applied with:
> $ patch -p0 < alsa-driver-1.0.17-1.patch
>
> See http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html
> for details on compiling and installing replacement snd-hda-intel + its
> dependent drivers.
> After the installation is completed, rerun the hsfmodem installation.
> Reboot and try to detect the modem with Root permission:
> wvdialconf /etc/wvdial.conf
>
> Read DOCs/Conexant.txt
>
> Writing DOCs/Conexant.txt
>
>
> Completed candidate modem analyses.
>
> The base of the UDEV device file system is: /dev/.udev
>
> The kernel was compiled with gcc version 4.3.1 and a compiler is not installed
>
> linux-headers-2.6.25.5-1.1-default resources needed for compiling are not manifestly ready!
> The patch utility is needed and is needed for compiling ALSA drivers, and possibly others.
>
> If compiling is necessary packages must be installed, providing:
> gcc-4.3 make kernel-source-2.6.25.5-1.1-default
>
>
> If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
> Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
> and any of its dependents, under Ubuntu linux-libc-dev
>
> If an alternate ethernet connection is available,
> $ apt-get update
> $ apt-get -s install linux-kernel-devel
> will install needed packages.
> For Debian/Ubuntu related distributions, run the following command to display the needed package list:
>
> Otherwise packages have to be found through http://packages.ubuntu.com
> Once downloaded and transferred into a Linux partition,
> they can be installed alltogether with:
> $ sudo dpkg -i *.deb
>
>
> Checking pppd properties:
> -rwsrwxr-x+ 1 root dialout 304644 2008-06-06 23:21 /usr/sbin/pppd
>
> In case of an "error 17" "serial loopback" problem, see:
> http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
>
> To enable dialout without Root permission do:
> $ su - root (not for Ubuntu)
> chmod a+x /usr/sbin/pppd
> or under Ubuntu related Linuxes
> chmod a+x /usr/sbin/pppd
>
> Checking settings of: /etc/ppp/options
> usehostname
> noipdefault
> noauth
> lock
> modem
> asyncmap 0
> nodetach
> lcp-echo-interval 30
> lcp-echo-failure 4
> lcp-max-configure 60
> lcp-restart 2
> idle 600
> noipx
> file /etc/ppp/filters
>
> In case of a message like:
> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
> see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
>
> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 ppp0 wlan0 wmaster0
> Which can interfere with Browser naviagation.
>
> Don't worry about the following, it is for experts should trouble shooting be necessary.
> ==========================================================
>
> Checking for modem support lines:
> --------------------------------------
> /device/modem symbolic link:
> slmodemd created symbolic link /dev/ttySL0:
> Within /etc/udev/ files:
> /etc/udev/rules.d/77-network.rules:SUBSYSTEM=="net", ENV{INTERFACE}=="ppp*|ippp*|isdn*|plip*|lo*|irda*|dummy*|ipsec*|tun*|tap*|bond*|br*|vlan*|modem*|dsl*", GOTO="skip_ifup"
> /etc/udev/rules.d/50-udev-default.rules:KERNEL=="mwave", NAME="modems/mwave", GROUP="uucp"
> Within /etc/modprobe.conf files:
> /etc/modprobe.conf:# Linux ACP modem (Mwave)
> Within any ancient /etc/devfs files:
>
> Within ancient kernel 2.4.n /etc/module.conf files:
>
> --------- end modem support lines --------
>
>
>
