-----Mensaje original----- De: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] Enviado el: Sunday, August 09, 2009 10:29 AM Para: Hermes CC: discuss@xxxxxxxxxxxxx Asunto: Re: RV: RV: FM56-USB modem on Ubuntu 9.04(CUBA) Hermes, RE: 0: 105 0 0 0 IO-APIC-edge timer 1: 36 43 39 39 IO-APIC-edge i8042 4: 2 1 1 2 IO-APIC-edge 6: 1 2 2 0 IO-APIC-edge floppy 7: 0 0 0 0 IO-APIC-edge parport0 8: 1 0 0 0 IO-APIC-edge rtc0 9: 0 0 0 0 IO-APIC-fasteoi acpi 12: 3281 3277 3276 3288 IO-APIC-edge i8042 14: 0 0 0 0 IO-APIC-edge ata_piix 15: 0 0 0 0 IO-APIC-edge ata_piix 16: 582 596 597 591 IO-APIC-fasteoi uhci_hcd:usb5, HDA Intel 18: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb4 19: 1530 1515 1518 1512 IO-APIC-fasteoi ata_piix, uhci_hcd:usb3 23: 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb1, uhci_hcd:usb2 2300: 0 0 0 0 PCI-MSI-edge eth0 ---------- Among these services, floppy, parport and eth0 could be shutdown without interferring with anything critical Make a file with $ sudo gedit /etc/modprobe.d/hermes.conf with lines: blacklist floppy blacklist parport # blacklist eth driver to be identified Save and reboot to activate. Do $ sudo ifconfig eth0 down $ cat /proc/interrupts | tee -a >> hermes2.txt $ dmesg >> hermes2.txt $ echo >> hermes.txt $ sudo tail -f /var/log/messages | tee -a >> hernes2.txt Attach the USB modem and send us the hermes2.txt MarvS On Sun, Aug 9, 2009 at 12:42 AM, Hermes<juan.osorio@xxxxxxxxxxxxxx> wrote: > MarvS > > This is what you ask.... > > -----Mensaje original----- > De: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] > Enviado el: Saturday, August 08, 2009 8:15 PM > Para: Hermes > CC: discuss@xxxxxxxxxxxxx > Asunto: Re: RV: FM56-USB modem on Ubuntu 9.04(CUBA) > > Try detaching as many external devices as possible before booting > Ubuntu , and shutting down as many programs as possible afterward. > Then: > $ cat /proc interrrupts | tee -a >> hermes.txt > $ sudo tail -f /var/log/messages | tee -a >>hermes.txt > > Then attach the modem, and afterward send us the hermes.txt > > MarvS > > On Sat, Aug 8, 2009 at 5:05 AM, Hermes<juan.osorio@xxxxxxxxxxxxxx> wrote: >> Marvin >> >> I did what you say with the same result, could be a conflict with another USB device... >> >> -----Mensaje original----- >> De: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] >> Enviado el: Saturday, August 08, 2009 8:01 AM >> Para: Hermes >> CC: discuss@xxxxxxxxxxxxx >> Asunto: Re: FM56-USB modem on Ubuntu 9.04(CUBA) >> >> Hemes, >> >> Through no fault of yours, this is a bad problem: >> Aug 7 08:26:14 hermes-desktop kernel: [ 81.393889] ST7554 USB Modem. >> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412076] *pde = 00000000 >> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412089] Dumping ftrace buffer: >> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412092] (ftrace buffer >> empty) >> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412094] Modules linked in: >> slusb(+) nls_iso8859_1 nls_cp437 vfat fat binfmt_misc bridge stp bnep >> slamr(P) video output input_polldev lp snd_hda_intel snd_pcm_oss >> ------- >> A first thing to try is deleting the unneeded slamr driver. >> >> Do >> $ find /lib/modules -name slamr.ko >> which will report the folder it is in, likely >> /lib/modules/2.6.28-13/extra/slamr.ko >> Delete it with: >> $ sudo rm lib/modules/2.6.28-13/extra/slamr.ko >> It should then not be seen by: >> $ ls lib/modules/2.6.28-13/extra/ >> >> Reboot and rerun the same tests. >> >> MarvS >> >> >> >> On Fri, Aug 7, 2009 at 9:55 PM, Hermes<juan.osorio@xxxxxxxxxxxxxx> wrote: >>> Marvin, >>> >>> I follow your instruction, when I run tain and plug in the modem USB cord >>> this happen. >>> >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.136016] usb 3-2: new full >>> speed USB device using uhci_hcd and address 2 >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.355148] usb 3-2: configuration >>> #1 chosen from 1 choice >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.393889] ST7554 USB Modem. >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412076] *pde = 00000000 >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412089] Dumping ftrace buffer: >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412092] (ftrace buffer >>> empty) >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412094] Modules linked in: >>> slusb(+) nls_iso8859_1 nls_cp437 vfat fat binfmt_misc bridge stp bnep >>> slamr(P) video output input_polldev lp snd_hda_intel snd_pcm_oss >>> snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi >>> snd_seq_midi_event iTCO_wdt psmouse iTCO_vendor_support ppdev snd_seq >>> parport_pc btusb pcspkr serio_raw snd_timer snd_seq_device parport intel_agp >>> agpgart snd soundcore snd_page_alloc usb_storage atl1 mii floppy fbcon >>> tileblit font bitblit softcursor >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412142] >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412145] Pid: 3467, comm: >>> modprobe Tainted: P (2.6.28-11-generic #42-Ubuntu) System Product >>> Name >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412149] EIP: 0060:[<c02cc06b>] >>> EFLAGS: 00010292 CPU: 2 >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412152] EIP is at >>> vsnprintf+0x2b/0x5c0 >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412154] EAX: f1c1eeb0 EBX: >>> 00000000 ECX: 00000000 EDX: 00000014 >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412156] ESI: fffffff4 EDI: >>> f1d0bcb4 EBP: f1d0bc64 ESP: f1d0bc1c >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412159] DS: 007b ES: 007b FS: >>> 00d8 GS: 0033 SS: 0068 >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412166] c06d3380 c06d3380 >>> c06d5780 f2e78000 00000010 f1d0bc8c c0193f99 00000014 >>> Aug 7 08:26:14 hermes-desktop kernel: [ 81.412409] ---[ end trace >>> 64cffe47f1f5c34a ] >>> >>> I installed wvdial and I run wvdialconf and this happen >>> >>> Scanning your serial ports for a modem. >>> >>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >>> Modem Port Scan<*1>: S1 S2 S3 >>> Sorry, no modem was detected! Is it in use by another program? >>> Did you configure it properly with setserial? >>> >>> Why this could happen???? >>> Sorry for my bad English.. >>> >>> >>> __________ Informacion de ESET Smart Security, version de la base de firmas >>> de virus 3832 (20090206) __________ >>> >>> ESET Smart Security ha comprobado este mensaje. >>> >>> http://www.eset.com >>> >>> >>> >>> -- >>> >>> Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas >>> >>> Infomed: http://www.sld.cu/ >>> >> >> __________ Informacin de ESET Smart Security, versin de la base de firmas de virus 3832 (20090206) __________ >> >> ESET Smart Security ha comprobado este mensaje. >> >> http://www.eset.com >> >> >> >> >> __________ Información de ESET Smart Security, versión de la base de firmas de virus 3832 (20090206) __________ >> >> ESET Smart Security ha comprobado este mensaje. >> >> http://www.eset.com >> >> >> >> -- >> >> Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas >> >> Infomed: http://www.sld.cu/ >> > > __________ Informacin de ESET Smart Security, versin de la base de firmas de virus 3832 (20090206) __________ > > ESET Smart Security ha comprobado este mensaje. > > http://www.eset.com > > > > > __________ Información de ESET Smart Security, versión de la base de firmas de virus 3832 (20090206) __________ > > ESET Smart Security ha comprobado este mensaje. > > http://www.eset.com > > > > -- > > Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas > > Infomed: http://www.sld.cu/ > > __________ Informacin de ESET Smart Security, versin de la base de firmas de virus 3832 (20090206) __________ ESET Smart Security ha comprobado este mensaje. http://www.eset.com __________ Información de ESET Smart Security, versión de la base de firmas de virus 3832 (20090206) __________ ESET Smart Security ha comprobado este mensaje. http://www.eset.com -- Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas Infomed: http://www.sld.cu/
CPU0 CPU1 CPU2 CPU3 0: 108 1 0 1 IO-APIC-edge timer 1: 60 57 58 54 IO-APIC-edge i8042 4: 1 1 2 2 IO-APIC-edge 6: 1 1 1 2 IO-APIC-edge floppy 7: 0 0 0 0 IO-APIC-edge parport0 8: 0 1 0 0 IO-APIC-edge rtc0 9: 0 0 0 0 IO-APIC-fasteoi acpi 12: 932 894 919 881 IO-APIC-edge i8042 14: 0 0 0 0 IO-APIC-edge ata_piix 15: 0 0 0 0 IO-APIC-edge ata_piix 16: 547 555 525 576 IO-APIC-fasteoi uhci_hcd:usb5, HDA Intel 18: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb4 19: 5133 5168 5158 5157 IO-APIC-fasteoi ata_piix, uhci_hcd:usb3 23: 1396 1397 1412 1401 IO-APIC-fasteoi ehci_hcd:usb1, uhci_hcd:usb2 NMI: 0 0 0 0 Non-maskable interrupts LOC: 10843 11003 10382 8177 Local timer interrupts RES: 639 366 475 443 Rescheduling interrupts CAL: 85 106 87 79 Function call interrupts TLB: 658 957 700 1093 TLB shootdowns SPU: 0 0 0 0 Spurious interrupts ERR: 0 MIS: 0 [ 0.000000] BIOS EBDA/lowmem at: 0009fc00/0009fc00 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.28-11-generic (buildd@palmer) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #42-Ubuntu SMP Fri Apr 17 01:57:59 UTC 2009 (Ubuntu 2.6.28-11.42-generic) [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bff90000 (usable) [ 0.000000] BIOS-e820: 00000000bff90000 - 00000000bff9e000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bff9e000 - 00000000bffd0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bffd0000 - 00000000bffde000 (reserved) [ 0.000000] BIOS-e820: 00000000bffe0000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] DMI present. [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working it around. [ 0.000000] last_pfn = 0xbff90 max_arch_pfn = 0x100000 [ 0.000000] Scanning 0 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable) [ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 00000000bff90000 (usable) [ 0.000000] modified: 00000000bff90000 - 00000000bff9e000 (ACPI data) [ 0.000000] modified: 00000000bff9e000 - 00000000bffd0000 (ACPI NVS) [ 0.000000] modified: 00000000bffd0000 - 00000000bffde000 (reserved) [ 0.000000] modified: 00000000bffe0000 - 00000000c0000000 (reserved) [ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] modified: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] kernel direct mapping tables up to 373fe000 @ 10000-16000 [ 0.000000] RAMDISK: 378bd000 - 37fefad1 [ 0.000000] Allocated new RAMDISK: 00881000 - 00fb3ad1 [ 0.000000] Move RAMDISK from 00000000378bd000 - 0000000037fefad0 to 00881000 - 00fb3ad0 [ 0.000000] ACPI: RSDP 000FB800, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT BFF90000, 0034 (r1 112907 RSDT1016 20071129 MSFT 97) [ 0.000000] ACPI: FACP BFF90200, 0084 (r2 112907 FACP1016 20071129 MSFT 97) [ 0.000000] ACPI: DSDT BFF905C0, 6829 (r1 A0820 A0820000 0 INTL 20060113) [ 0.000000] ACPI: FACS BFF9E000, 0040 [ 0.000000] ACPI: APIC BFF90390, 006C (r1 112907 APIC1016 20071129 MSFT 97) [ 0.000000] ACPI: MCFG BFF90400, 003C (r1 112907 OEMMCFG 20071129 MSFT 97) [ 0.000000] ACPI: OEMB BFF9E040, 0061 (r1 112907 OEMB1016 20071129 MSFT 97) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] 2187MB HIGHMEM available. [ 0.000000] 883MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 373fe000 [ 0.000000] low ram: 00000000 - 373fe000 [ 0.000000] bootmap 00012000 - 00018e80 [ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] [ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] [ 0.000000] #3 [0000100000 - 000087c52c] TEXT DATA BSS ==> [0000100000 - 000087c52c] [ 0.000000] #4 [000087d000 - 0000881000] INIT_PG_TABLE ==> [000087d000 - 0000881000] [ 0.000000] #5 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] [ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000] [ 0.000000] #7 [0000881000 - 0000fb3ad1] NEW RAMDISK ==> [0000881000 - 0000fb3ad1] [ 0.000000] #8 [0000012000 - 0000019000] BOOTMAP ==> [0000012000 - 0000019000] [ 0.000000] found SMP MP-table at [c00ff780] 000ff780 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] Normal 0x00001000 -> 0x000373fe [ 0.000000] HighMem 0x000373fe -> 0x000bff90 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x000bff90 [ 0.000000] On node 0 totalpages: 786207 [ 0.000000] free_area_init_node: node 0, pgdat c06d0f80, node_mem_map c1000200 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3951 pages, LIFO batch:0 [ 0.000000] Normal zone: 1736 pages used for memmap [ 0.000000] Normal zone: 220470 pages, LIFO batch:31 [ 0.000000] HighMem zone: 4376 pages used for memmap [ 0.000000] HighMem zone: 555642 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000 [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at c4000000 (gap: c0000000:3ee00000) [ 0.000000] PERCPU: Allocating 45056 bytes of per cpu data [ 0.000000] NR_CPUS: 64, nr_cpu_ids: 4, nr_node_ids 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 780063 [ 0.000000] Kernel command line: root=UUID=111675b3-3d6e-4c5e-89c5-5fe9dbefd32b ro quiet splash [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 2399.917 MHz processor. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.004000] allocated 15726080 bytes of page_cgroup [ 0.004000] please try cgroup_disable=memory option if you don't want [ 0.004000] Scanning for low memory corruption every 60 seconds [ 0.004000] Memory: 3087904k/3145280k available (4126k kernel code, 56052k reserved, 2208k data, 532k init, 2240072k highmem) [ 0.004000] virtual kernel memory layout: [ 0.004000] fixmap : 0xffc77000 - 0xfffff000 (3616 kB) [ 0.004000] pkmap : 0xff400000 - 0xff800000 (4096 kB) [ 0.004000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB) [ 0.004000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB) [ 0.004000] .init : 0xc0737000 - 0xc07bc000 ( 532 kB) [ 0.004000] .data : 0xc0507a6f - 0xc072fe60 (2208 kB) [ 0.004000] .text : 0xc0100000 - 0xc0507a6f (4126 kB) [ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.004013] Calibrating delay loop (skipped), value calculated using timer frequency.. 4799.83 BogoMIPS (lpj=9599668) [ 0.004029] Security Framework initialized [ 0.004037] SELinux: Disabled at boot. [ 0.004055] AppArmor: AppArmor initialized [ 0.004062] Mount-cache hash table entries: 512 [ 0.004191] Initializing cgroup subsys ns [ 0.004196] Initializing cgroup subsys cpuacct [ 0.004198] Initializing cgroup subsys memory [ 0.004201] Initializing cgroup subsys freezer [ 0.004215] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.004217] CPU: L2 cache: 4096K [ 0.004219] CPU: Physical Processor ID: 0 [ 0.004221] CPU: Processor Core ID: 0 [ 0.004224] using mwait in idle threads. [ 0.004233] Checking 'hlt' instruction... OK. [ 0.022086] ACPI: Core revision 20080926 [ 0.024168] ACPI: Checking initramfs for custom DSDT [ 0.272413] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.313116] CPU0: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b [ 0.316001] APIC calibration not consistent with PM Timer: 120ms instead of 100ms [ 0.316001] APIC delta adjusted to PM-Timer: 1666662 (2000112) [ 0.316001] Booting processor 1 APIC 0x1 ip 0x6000 [ 0.004000] Initializing CPU#1 [ 0.004000] Calibrating delay using timer specific routine.. 4800.01 BogoMIPS (lpj=9600036) [ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.004000] CPU: L2 cache: 4096K [ 0.004000] CPU: Physical Processor ID: 0 [ 0.004000] CPU: Processor Core ID: 1 [ 0.400566] CPU1: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b [ 0.400580] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 0.404111] Booting processor 2 APIC 0x2 ip 0x6000 [ 0.004000] Initializing CPU#2 [ 0.004000] Calibrating delay using timer specific routine.. 4800.02 BogoMIPS (lpj=9600054) [ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.004000] CPU: L2 cache: 4096K [ 0.004000] CPU: Physical Processor ID: 0 [ 0.004000] CPU: Processor Core ID: 2 [ 0.492581] CPU2: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b [ 0.492594] checking TSC synchronization [CPU#0 -> CPU#2]: passed. [ 0.496085] Booting processor 3 APIC 0x3 ip 0x6000 [ 0.004000] Initializing CPU#3 [ 0.004000] Calibrating delay using timer specific routine.. 4800.03 BogoMIPS (lpj=9600067) [ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.004000] CPU: L2 cache: 4096K [ 0.004000] CPU: Physical Processor ID: 0 [ 0.004000] CPU: Processor Core ID: 3 [ 0.584529] CPU3: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b [ 0.584542] checking TSC synchronization [CPU#0 -> CPU#3]: passed. [ 0.588024] Brought up 4 CPUs [ 0.588026] Total of 4 processors activated (19199.91 BogoMIPS). [ 0.588081] CPU0 attaching sched-domain: [ 0.588083] domain 0: span 0-1 level MC [ 0.588085] groups: 0 1 [ 0.588088] domain 1: span 0-3 level CPU [ 0.588090] groups: 0-1 2-3 [ 0.588095] CPU1 attaching sched-domain: [ 0.588096] domain 0: span 0-1 level MC [ 0.588098] groups: 1 0 [ 0.588100] domain 1: span 0-3 level CPU [ 0.588102] groups: 0-1 2-3 [ 0.588106] CPU2 attaching sched-domain: [ 0.588107] domain 0: span 2-3 level MC [ 0.588109] groups: 2 3 [ 0.588112] domain 1: span 0-3 level CPU [ 0.588113] groups: 2-3 0-1 [ 0.588120] CPU3 attaching sched-domain: [ 0.588121] domain 0: span 2-3 level MC [ 0.588123] groups: 3 2 [ 0.588126] domain 1: span 0-3 level CPU [ 0.588127] groups: 2-3 0-1 [ 0.588231] net_namespace: 776 bytes [ 0.588231] Booting paravirtualized kernel on bare hardware [ 0.588291] Time: 1:35:49 Date: 08/09/09 [ 0.588291] regulator: core version 0.5 [ 0.588291] NET: Registered protocol family 16 [ 0.588291] EISA bus registered [ 0.588291] ACPI: bus type pci registered [ 0.588291] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 [ 0.588291] PCI: Not using MMCONFIG. [ 0.588315] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4 [ 0.588317] PCI: Using configuration type 1 for base access [ 0.589024] ACPI: EC: Look up EC in DSDT [ 0.598648] ACPI: Interpreter enabled [ 0.598659] ACPI: (supports S0 S1 S3 S4 S5) [ 0.598676] ACPI: Using IOAPIC for interrupt routing [ 0.598721] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 [ 0.601675] PCI: MCFG area at f0000000 reserved in ACPI motherboard resources [ 0.601677] PCI: Using MMCONFIG for extended config space [ 0.608291] ACPI: No dock devices found. [ 0.608343] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.608417] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 0.608420] pci 0000:00:01.0: PME# disabled [ 0.608474] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf9ef8000-0xf9efbfff] [ 0.608499] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.608502] pci 0000:00:1b.0: PME# disabled [ 0.608541] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.608544] pci 0000:00:1c.0: PME# disabled [ 0.608585] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 0.608588] pci 0000:00:1c.1: PME# disabled [ 0.608630] pci 0000:00:1d.0: reg 20 io port: [0xc880-0xc89f] [ 0.608671] pci 0000:00:1d.1: reg 20 io port: [0xcc00-0xcc1f] [ 0.608711] pci 0000:00:1d.2: reg 20 io port: [0xd000-0xd01f] [ 0.608762] pci 0000:00:1d.3: reg 20 io port: [0xd080-0xd09f] [ 0.608807] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf9effc00-0xf9efffff] [ 0.608851] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.608854] pci 0000:00:1d.7: PME# disabled [ 0.608957] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.608962] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 0.608965] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.608989] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07] [ 0.608995] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03] [ 0.609000] pci 0000:00:1f.1: reg 18 io port: [0x8f0-0x8f7] [ 0.609006] pci 0000:00:1f.1: reg 1c io port: [0x8f8-0x8fb] [ 0.609011] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf] [ 0.609044] pci 0000:00:1f.2: reg 10 io port: [0xdc00-0xdc07] [ 0.609049] pci 0000:00:1f.2: reg 14 io port: [0xd880-0xd883] [ 0.609054] pci 0000:00:1f.2: reg 18 io port: [0xd800-0xd807] [ 0.609059] pci 0000:00:1f.2: reg 1c io port: [0xd480-0xd483] [ 0.609064] pci 0000:00:1f.2: reg 20 io port: [0xd400-0xd40f] [ 0.609078] pci 0000:00:1f.2: PME# supported from D3hot [ 0.609081] pci 0000:00:1f.2: PME# disabled [ 0.609121] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f] [ 0.609165] pci 0000:04:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff] [ 0.609173] pci 0000:04:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff] [ 0.609181] pci 0000:04:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff] [ 0.609186] pci 0000:04:00.0: reg 24 io port: [0xec00-0xec7f] [ 0.609191] pci 0000:04:00.0: reg 30 32bit mmio: [0xfebe0000-0xfebfffff] [ 0.609233] pci 0000:00:01.0: bridge io port: [0xe000-0xefff] [ 0.609235] pci 0000:00:01.0: bridge 32bit mmio: [0xfa000000-0xfebfffff] [ 0.609239] pci 0000:00:01.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff] [ 0.609326] pci 0000:02:00.0: reg 10 64bit mmio: [0xf9fc0000-0xf9ffffff] [ 0.609356] pci 0000:02:00.0: reg 30 32bit mmio: [0xf9fa0000-0xf9fbffff] [ 0.609366] pci 0000:02:00.0: PME# supported from D3hot D3cold [ 0.609371] pci 0000:02:00.0: PME# disabled [ 0.609416] pci 0000:00:1c.1: bridge 32bit mmio: [0xf9f00000-0xf9ffffff] [ 0.609461] pci 0000:00:1e.0: transparent bridge [ 0.609483] bus 00 -> node 0 [ 0.609488] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.609663] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.609819] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] [ 0.609910] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT] [ 0.617068] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 0.617176] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.617282] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.617388] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 0.617493] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.617599] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.617705] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.617811] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 0.617912] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 79, should be 6C [20080926] [ 0.617931] ACPI: WMI: Mapper loaded [ 0.617967] SCSI subsystem initialized [ 0.617967] libata version 3.00 loaded. [ 0.617967] usbcore: registered new interface driver usbfs [ 0.617967] usbcore: registered new interface driver hub [ 0.617967] usbcore: registered new device driver usb [ 0.617967] PCI: Using ACPI for IRQ routing [ 0.624012] Bluetooth: Core ver 2.13 [ 0.624029] NET: Registered protocol family 31 [ 0.624029] Bluetooth: HCI device and connection manager initialized [ 0.624029] Bluetooth: HCI socket layer initialized [ 0.624029] NET: Registered protocol family 8 [ 0.624029] NET: Registered protocol family 20 [ 0.624040] NetLabel: Initializing [ 0.624043] NetLabel: domain hash size = 128 [ 0.624045] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.624059] NetLabel: unlabeled traffic allowed by default [ 0.624181] hpet clockevent registered [ 0.624183] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.624187] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.624191] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.632065] AppArmor: AppArmor Filesystem Enabled [ 0.640032] pnp: PnP ACPI init [ 0.640041] ACPI: bus type pnp registered [ 0.643733] pnp: PnP ACPI: found 18 devices [ 0.643734] ACPI: ACPI bus type pnp unregistered [ 0.643738] PnPBIOS: Disabled by ACPI PNP [ 0.643746] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved [ 0.643752] system 00:08: ioport range 0x290-0x297 has been reserved [ 0.643757] system 00:09: ioport range 0x4d0-0x4d1 has been reserved [ 0.643759] system 00:09: ioport range 0x800-0x87f has been reserved [ 0.643761] system 00:09: ioport range 0x480-0x4bf has been reserved [ 0.643764] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.643766] system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved [ 0.643771] system 00:0b: iomem range 0xffc00000-0xffefffff has been reserved [ 0.643776] system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved [ 0.643778] system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.643783] system 00:10: iomem range 0xf0000000-0xf3ffffff has been reserved [ 0.643788] system 00:11: iomem range 0x0-0x9ffff could not be reserved [ 0.643790] system 00:11: iomem range 0xc0000-0xcffff could not be reserved [ 0.643792] system 00:11: iomem range 0xe0000-0xfffff could not be reserved [ 0.643795] system 00:11: iomem range 0x100000-0xbfffffff could not be reserved [ 0.678450] pci 0000:00:01.0: PCI bridge, secondary bus 0000:04 [ 0.678452] pci 0000:00:01.0: IO window: 0xe000-0xefff [ 0.678456] pci 0000:00:01.0: MEM window: 0xfa000000-0xfebfffff [ 0.678458] pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000efffffff [ 0.678462] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03 [ 0.678464] pci 0000:00:1c.0: IO window: disabled [ 0.678467] pci 0000:00:1c.0: MEM window: disabled [ 0.678470] pci 0000:00:1c.0: PREFETCH window: disabled [ 0.678475] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 [ 0.678477] pci 0000:00:1c.1: IO window: disabled [ 0.678481] pci 0000:00:1c.1: MEM window: 0xf9f00000-0xf9ffffff [ 0.678484] pci 0000:00:1c.1: PREFETCH window: disabled [ 0.678489] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01 [ 0.678491] pci 0000:00:1e.0: IO window: disabled [ 0.678495] pci 0000:00:1e.0: MEM window: disabled [ 0.678498] pci 0000:00:1e.0: PREFETCH window: disabled [ 0.678508] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.678511] pci 0000:00:01.0: setting latency timer to 64 [ 0.678517] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.678520] pci 0000:00:1c.0: setting latency timer to 64 [ 0.678527] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.678530] pci 0000:00:1c.1: setting latency timer to 64 [ 0.678536] pci 0000:00:1e.0: setting latency timer to 64 [ 0.678539] bus: 00 index 0 io port: [0x00-0xffff] [ 0.678540] bus: 00 index 1 mmio: [0x000000-0xffffffff] [ 0.678542] bus: 04 index 0 io port: [0xe000-0xefff] [ 0.678544] bus: 04 index 1 mmio: [0xfa000000-0xfebfffff] [ 0.678545] bus: 04 index 2 mmio: [0xe0000000-0xefffffff] [ 0.678547] bus: 04 index 3 mmio: [0x0-0x0] [ 0.678548] bus: 03 index 0 mmio: [0x0-0x0] [ 0.678550] bus: 03 index 1 mmio: [0x0-0x0] [ 0.678551] bus: 03 index 2 mmio: [0x0-0x0] [ 0.678553] bus: 03 index 3 mmio: [0x0-0x0] [ 0.678554] bus: 02 index 0 mmio: [0x0-0x0] [ 0.678556] bus: 02 index 1 mmio: [0xf9f00000-0xf9ffffff] [ 0.678557] bus: 02 index 2 mmio: [0x0-0x0] [ 0.678558] bus: 02 index 3 mmio: [0x0-0x0] [ 0.678560] bus: 01 index 0 mmio: [0x0-0x0] [ 0.678561] bus: 01 index 1 mmio: [0x0-0x0] [ 0.678562] bus: 01 index 2 mmio: [0x0-0x0] [ 0.678564] bus: 01 index 3 io port: [0x00-0xffff] [ 0.678565] bus: 01 index 4 mmio: [0x000000-0xffffffff] [ 0.678572] NET: Registered protocol family 2 [ 0.692155] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.692355] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.692705] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.692880] TCP: Hash tables configured (established 131072 bind 65536) [ 0.692882] TCP reno registered [ 0.700209] NET: Registered protocol family 1 [ 0.700316] checking if image is initramfs... it is [ 1.124758] Switched to high resolution mode on CPU 1 [ 1.127327] Switched to high resolution mode on CPU 3 [ 1.127406] Switched to high resolution mode on CPU 2 [ 1.128146] Switched to high resolution mode on CPU 0 [ 1.199123] Freeing initrd memory: 7370k freed [ 1.199481] cpufreq: No nForce2 chipset. [ 1.199595] audit: initializing netlink socket (disabled) [ 1.199610] type=2000 audit(1249781749.196:1): initialized [ 1.205607] highmem bounce pool size: 64 pages [ 1.205611] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 1.206758] VFS: Disk quotas dquot_6.5.1 [ 1.206823] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.207324] fuse init (API version 7.10) [ 1.207427] msgmni has been set to 1672 [ 1.207670] alg: No test for stdrng (krng) [ 1.207682] io scheduler noop registered [ 1.207684] io scheduler anticipatory registered [ 1.207685] io scheduler deadline registered [ 1.207701] io scheduler cfq registered (default) [ 1.207790] pci 0000:04:00.0: Boot video device [ 1.210767] pcieport-driver 0000:00:01.0: setting latency timer to 64 [ 1.210795] pcieport-driver 0000:00:01.0: found MSI capability [ 1.210814] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X [ 1.210822] pci_express 0000:00:01.0:pcie00: allocate port service [ 1.210833] pci_express 0000:00:01.0:pcie03: allocate port service [ 1.210870] pcieport-driver 0000:00:1c.0: setting latency timer to 64 [ 1.210898] pcieport-driver 0000:00:1c.0: found MSI capability [ 1.210918] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X [ 1.210928] pci_express 0000:00:1c.0:pcie00: allocate port service [ 1.210938] pci_express 0000:00:1c.0:pcie02: allocate port service [ 1.210947] pci_express 0000:00:1c.0:pcie03: allocate port service [ 1.210992] pcieport-driver 0000:00:1c.1: setting latency timer to 64 [ 1.211020] pcieport-driver 0000:00:1c.1: found MSI capability [ 1.211040] pcieport-driver 0000:00:1c.1: irq 2301 for MSI/MSI-X [ 1.211049] pci_express 0000:00:1c.1:pcie00: allocate port service [ 1.211059] pci_express 0000:00:1c.1:pcie02: allocate port service [ 1.211070] pci_express 0000:00:1c.1:pcie03: allocate port service [ 1.211123] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.211604] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 1.211715] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 1.211717] ACPI: Power Button (FF) [PWRF] [ 1.211763] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 1.211765] ACPI: Power Button (CM) [PWRB] [ 1.212170] ACPI: SSDT BFF9E0B0, 01D2 (r1 AMI CPU1PM 1 INTL 20060113) [ 1.212428] processor ACPI_CPU:00: registered as cooling_device0 [ 1.212667] ACPI: SSDT BFF9E290, 0143 (r1 AMI CPU2PM 1 INTL 20060113) [ 1.212910] processor ACPI_CPU:01: registered as cooling_device1 [ 1.213139] ACPI: SSDT BFF9E3E0, 0143 (r1 AMI CPU3PM 1 INTL 20060113) [ 1.213378] processor ACPI_CPU:02: registered as cooling_device2 [ 1.213615] ACPI: SSDT BFF9E530, 0143 (r1 AMI CPU4PM 1 INTL 20060113) [ 1.213855] processor ACPI_CPU:03: registered as cooling_device3 [ 1.215968] isapnp: Scanning for PnP cards... [ 1.568853] isapnp: No Plug & Play device found [ 1.577656] Serial: 8250/16550 driver4 ports, IRQ sharing enabled [ 1.577737] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.578165] 00:0f: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.578745] brd: module loaded [ 1.578982] loop: module loaded [ 1.579034] Fixed MDIO Bus: probed [ 1.579039] PPP generic driver version 2.4.2 [ 1.579080] input: Macintosh mouse button emulation as /devices/virtual/input/input2 [ 1.579102] Driver 'sd' needs updating - please use bus_type methods [ 1.579109] Driver 'sr' needs updating - please use bus_type methods [ 1.579164] ata_piix 0000:00:1f.1: version 2.12 [ 1.579173] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.579198] ata_piix 0000:00:1f.1: setting latency timer to 64 [ 1.579279] scsi0 : ata_piix [ 1.579379] scsi1 : ata_piix [ 1.580424] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 [ 1.580426] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 [ 1.902691] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.902694] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 1.902718] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 1.902780] scsi2 : ata_piix [ 1.902849] scsi3 : ata_piix [ 1.903966] ata3: SATA max UDMA/133 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 19 [ 1.903968] ata4: SATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 19 [ 2.068586] ata3.00: ATA-8: ST3500820AS, SD15, max UDMA/133 [ 2.068589] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 2.084606] ata3.00: configured for UDMA/133 [ 2.250695] scsi 2:0:0:0: Direct-Access ATA ST3500820AS SD15 PQ: 0 ANSI: 5 [ 2.250767] sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB) [ 2.250779] sd 2:0:0:0: [sda] Write Protect is off [ 2.250781] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.250801] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.250848] sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB) [ 2.250859] sd 2:0:0:0: [sda] Write Protect is off [ 2.250861] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.250880] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.250883] sda: sda1 sda2 < sda5 sda6 sda7 > [ 2.320793] sd 2:0:0:0: [sda] Attached SCSI disk [ 2.320826] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 2.321342] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.321357] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 2.321380] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.321383] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.321429] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.325326] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.325331] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 2.325341] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9effc00 [ 2.340021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.340092] usb usb1: configuration #1 chosen from 1 choice [ 2.340123] hub 1-0:1.0: USB hub found [ 2.340136] hub 1-0:1.0: 8 ports detected [ 2.340221] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.340232] uhci_hcd: USB Universal Host Controller Interface driver [ 2.340249] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 2.340253] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.340255] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.340286] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.340306] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c880 [ 2.340359] usb usb2: configuration #1 chosen from 1 choice [ 2.340380] hub 2-0:1.0: USB hub found [ 2.340385] hub 2-0:1.0: 2 ports detected [ 2.340445] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 2.340450] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.340452] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.340482] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.340501] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000cc00 [ 2.340560] usb usb3: configuration #1 chosen from 1 choice [ 2.340579] hub 3-0:1.0: USB hub found [ 2.340583] hub 3-0:1.0: 2 ports detected [ 2.340644] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 2.340649] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.340651] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.340687] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.340712] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d000 [ 2.340762] usb usb4: configuration #1 chosen from 1 choice [ 2.340781] hub 4-0:1.0: USB hub found [ 2.340786] hub 4-0:1.0: 2 ports detected [ 2.340847] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 2.340851] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 2.340854] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 2.340884] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 [ 2.340909] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d080 [ 2.340962] usb usb5: configuration #1 chosen from 1 choice [ 2.340982] hub 5-0:1.0: USB hub found [ 2.340987] hub 5-0:1.0: 2 ports detected [ 2.341080] usbcore: registered new interface driver libusual [ 2.341103] usbcore: registered new interface driver usbserial [ 2.341113] USB Serial support registered for generic [ 2.341125] usbcore: registered new interface driver usbserial_generic [ 2.341126] usbserial: USB Serial Driver core [ 2.341171] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 2.343857] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.343864] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.344559] mice: PS/2 mouse device common for all mice [ 2.356603] rtc_cmos 00:03: RTC can wake from S4 [ 2.356660] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 2.356682] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 2.356771] device-mapper: uevent: version 1.0.3 [ 2.356842] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@xxxxxxxxxx [ 2.356960] device-mapper: multipath: version 1.0.5 loaded [ 2.356962] device-mapper: multipath round-robin: version 1.0.0 loaded [ 2.357046] EISA: Probing bus 0 at eisa.0 [ 2.357072] EISA: Detected 0 cards. [ 2.357169] cpuidle: using governor ladder [ 2.357170] cpuidle: using governor menu [ 2.357602] TCP cubic registered [ 2.357687] NET: Registered protocol family 10 [ 2.358040] lo: Disabled Privacy Extensions [ 2.358297] NET: Registered protocol family 17 [ 2.358313] Bluetooth: L2CAP ver 2.11 [ 2.358314] Bluetooth: L2CAP socket layer initialized [ 2.358317] Bluetooth: SCO (Voice Link) ver 0.6 [ 2.358318] Bluetooth: SCO socket layer initialized [ 2.358342] Bluetooth: RFCOMM socket layer initialized [ 2.358348] Bluetooth: RFCOMM TTY layer initialized [ 2.358350] Bluetooth: RFCOMM ver 1.10 [ 2.359203] Using IPI No-Shortcut mode [ 2.359261] registered taskstats version 1 [ 2.359349] Magic number: 5:818:558 [ 2.359407] rtc_cmos 00:03: setting system clock to 2009-08-09 01:35:51 UTC (1249781751) [ 2.359409] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.359410] EDD information not available. [ 2.359580] Freeing unused kernel memory: 532k freed [ 2.359689] Write protecting the kernel text: 4128k [ 2.359727] Write protecting the kernel read-only data: 1532k [ 2.374271] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 [ 2.497383] Floppy drive(s): fd0 is 1.44M [ 2.507845] atl1 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2.507856] atl1 0000:02:00.0: setting latency timer to 64 [ 2.507910] atl1 0000:02:00.0: version 2.1.3 [ 2.516864] FDC 0 is a post-1991 82077 [ 2.653538] usb 1-7: new high speed USB device using ehci_hcd and address 2 [ 2.786116] usb 1-7: configuration #1 chosen from 1 choice [ 2.789540] Initializing USB Mass Storage driver... [ 2.790169] scsi4 : SCSI emulation for USB Mass Storage devices [ 2.790420] usbcore: registered new interface driver usb-storage [ 2.790424] USB Mass Storage support registered. [ 2.790495] usb-storage: device found at 2 [ 2.790497] usb-storage: waiting for device to settle before scanning [ 3.136674] PM: Starting manual resume from disk [ 3.136677] PM: Resume from partition 8:7 [ 3.136678] PM: Checking hibernation image. [ 3.136955] PM: Resume from disk failed. [ 3.164506] EXT4-fs: barriers enabled [ 3.169670] kjournald2 starting. Commit interval 5 seconds [ 3.169689] EXT4-fs: delayed allocation enabled [ 3.169692] EXT4-fs: file extents enabled [ 3.170155] EXT4-fs: mballoc enabled [ 3.170158] EXT4-fs: mounted filesystem with ordered data mode. [ 6.853804] udev: starting version 141 [ 7.098581] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 7.101461] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume [ 7.171289] parport_pc 00:07: reported by Plug and Play ACPI [ 7.171389] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] [ 7.225833] ppdev: user-space parallel port driver [ 7.569120] intel_rng: FWH not detected [ 7.582121] Linux agpgart interface v0.103 [ 7.589230] psmouse serio1: ID: 10 00 64<6>iTCO_vendor_support: vendor-support=0 [ 7.657520] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05 [ 7.657643] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860) [ 7.657711] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 7.734099] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 7.734144] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 7.788186] usb-storage: device scan complete [ 7.788787] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0 [ 7.789422] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0 [ 7.790023] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0 [ 7.790660] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0 [ 7.792150] sd 4:0:0:0: [sdb] Attached SCSI removable disk [ 7.792245] sd 4:0:0:0: Attached scsi generic sg1 type 0 [ 7.793109] sd 4:0:0:1: [sdc] Attached SCSI removable disk [ 7.793182] sd 4:0:0:1: Attached scsi generic sg2 type 0 [ 7.794030] sd 4:0:0:2: [sdd] Attached SCSI removable disk [ 7.794136] sd 4:0:0:2: Attached scsi generic sg3 type 0 [ 7.795297] sd 4:0:0:3: [sde] Attached SCSI removable disk [ 7.795349] sd 4:0:0:3: Attached scsi generic sg4 type 0 [ 7.895174] lp0: using parport0 (interrupt-driven). [ 7.953102] Adding 497972k swap on /dev/sda7. Priority:-1 extents:1 across:497972k [ 8.215427] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input5 [ 8.482511] EXT4 FS on sda6, internal journal on sda6:8 [ 9.442662] type=1505 audit(1249796158.581:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2108 [ 9.479547] type=1505 audit(1249796158.617:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2112 [ 9.479617] type=1505 audit(1249796158.617:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2112 [ 9.479647] type=1505 audit(1249796158.617:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2112 [ 9.479675] type=1505 audit(1249796158.617:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2112 [ 9.580710] type=1505 audit(1249796158.717:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2117 [ 9.580856] type=1505 audit(1249796158.717:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2117 [ 9.602606] type=1505 audit(1249796158.742:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2121 [ 11.541456] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 11.541459] Bluetooth: BNEP filters: protocol multicast [ 11.561787] Bridge firewalling registered [ 16.862291] atl1 0000:02:00.0: irq 2300 for MSI/MSI-X [ 16.862512] ADDRCONF(NETDEV_UP): eth0: link is not ready Aug 9 01:35:59 hermes-desktop kernel: [ 9.479647] type=1505 audit(1249796158.617:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2112 Aug 9 01:35:59 hermes-desktop kernel: [ 9.479675] type=1505 audit(1249796158.617:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2112 Aug 9 01:35:59 hermes-desktop kernel: [ 9.580710] type=1505 audit(1249796158.717:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2117 Aug 9 01:35:59 hermes-desktop kernel: [ 9.580856] type=1505 audit(1249796158.717:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2117 Aug 9 01:35:59 hermes-desktop kernel: [ 9.602606] type=1505 audit(1249796158.742:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2121 Aug 9 01:36:00 hermes-desktop kernel: [ 11.541456] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Aug 9 01:36:00 hermes-desktop kernel: [ 11.541459] Bluetooth: BNEP filters: protocol multicast Aug 9 01:36:00 hermes-desktop kernel: [ 11.561787] Bridge firewalling registered Aug 9 01:36:06 hermes-desktop kernel: [ 16.862512] ADDRCONF(NETDEV_UP): eth0: link is not ready Aug 9 01:55:52 hermes-desktop syslogd 1.5.0#5ubuntu3: restart. Aug 9 02:00:17 hermes-desktop kernel: [ 1467.992011] usb 3-2: new full speed USB device using uhci_hcd and address 2 Aug 9 02:00:17 hermes-desktop kernel: [ 1468.155416] usb 3-2: configuration #1 chosen from 1 choice Aug 9 02:00:17 hermes-desktop kernel: [ 1468.186416] ST7554 USB Modem. Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205094] *pde = 00000000 Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205107] Dumping ftrace buffer: Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205110] (ftrace buffer empty) Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205113] Modules linked in: slusb(+) binfmt_misc bridge stp bnep video output input_polldev lp snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi iTCO_wdt snd_seq_midi_event iTCO_vendor_support snd_seq snd_timer snd_seq_device intel_agp agpgart snd soundcore snd_page_alloc ppdev parport_pc parport pcspkr psmouse serio_raw usb_storage atl1 mii floppy fbcon tileblit font bitblit softcursor Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205154] Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205158] Pid: 3988, comm: modprobe Not tainted (2.6.28-11-generic #42-Ubuntu) System Product Name Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205161] EIP: 0060:[<c02cc06b>] EFLAGS: 00010292 CPU: 0 Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205164] EIP is at vsnprintf+0x2b/0x5c0 Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205166] EAX: ef47bcb0 EBX: 00000000 ECX: 00000000 EDX: 00000014 Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205169] ESI: fffffff4 EDI: ef323cb4 EBP: ef323c64 ESP: ef323c1c Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205171] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205178] c06d3380 c06d3380 c06d5780 f55f3ed0 00000010 ef323c8c c0193f99 00000014 Aug 9 02:00:17 hermes-desktop kernel: [ 1468.205420] ---[ end trace 3561db14450cdf0c ]---
