Usman, For the first one: For candidate card in slot 00:08.0, firmware information and bootup diagnostics are: PCI slot PCI ID SubsystemID Name ---------- --------- --------- -------------- 00:08.0 10b9:5457 0e11:005a Modem: ALi Corporation M5457 AC'97 Modem Controller Support type needed or chipset: slamr The modem is supported by the Smartlink slamr plus the slmodemd helper utility. Read the DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow through guidance. A precompiled one is here. Download it and follow instructions: http://linmodems.technion.ac.il/packages/smartlink/Ubuntu/slamr-2.6.28-11-generic.tar.gz For the other part: For candidate card in slot 00:06.0, firmware information and bootup diagnostics are: PCI slot PCI ID SubsystemID Name ---------- --------- --------- -------------- 00:06.0 10b9:5451 0e11:005a Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device Support type needed or chipset: slmodemd An ALSA (Advanced Linux Sound Architecture) modem driver: snd-ali5451 provides Low Level support enabling contact with the modem hardware. For all BUT Conexant chip soft modems (using hsfmodem software) complementary High Level support is through a Smartlink utility: slmodemd Download from http://linmodems.technion.ac.il/packages/smartlink/ the package SLMODEMD.gcc4.3.tar.gz having a compiled slmodemd. Unpack under Linux with: $ tar zxf SLMODEMD.gcc4.3.tar.gz and read instructions therein. But briefly, the modem is setup with command: slmodemd -c YOUR_COUNTRY --alsa -shw:0,1 reporting dynamic creation of ports: /dev/ttySL0 --> /dev/pts/N , with N some number Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow through guidance. Regards, Antonio On 6/18/09, Usman Farooq <ufarooq08@xxxxxxxxx> wrote: > Hello, > > I am trying to get my Modem to work with HP Laptop nc4010. Can you > please help me figure out how I can make use of my Modem. I am new to > Ubuntu and Linux in general. Thank you in advance. > > Sincerely, > > Usman Farooq > > > =============ModemData.txt=========== > > Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List > Server, > as HTML can contain viruses. Use as the email Subject Line: > YourName, YourCountry kernel 2.6.28-11-generic > With this Subject Line cogent experts will be alerted, and useful > case names left in the Archive. > YourCountry will enable Country specific guidance. Linux experts in > YourCountry > can be found through: http://www.linux.org/groups/index.html. > They will know your Country's modem code, which may be essential for > dialup service. > Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an > Internet Provider mail filters. > So in a day, also check the Archived responses at http://www.linmodems.org > -------------------------- System information ---------------------------- > CPU=i686, > Linux version 2.6.28-11-generic (buildd@palmer) (gcc version 4.3.3 > (Ubuntu 4.3.3-5ubuntu4) ) #42-Ubuntu SMP Fri Apr 17 01:57:59 UTC 2009 > scanModem update of: 2009_05_31 > > There are no blacklisted modem drivers in /etc/modprobe* files > Potentially useful modem drivers now loaded are: > > > If a USB modem or cellphone is attached and was not detected, please > provide available information in your request to discuss@xxxxxxxxxxxxx > > For candidate card in slot 00:08.0, firmware information and bootup > diagnostics are: > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:08.0 10b9:5457 0e11:005a Modem: ALi Corporation M5457 AC'97 Modem > Controller > > Modem interrupt assignment and sharing: > 11: 1904 XT-PIC-XT yenta, yenta, ALI 5451 > --- Bootup diagnostics for card in PCI slot 00:08.0 ---- > [ 0.585229] pci 0000:00:08.0: reg 10 32bit mmio: [0x98100000-0x98100fff] > [ 0.585235] pci 0000:00:08.0: reg 14 io port: [0x3400-0x34ff] > [ 0.585257] pci 0000:00:08.0: PME# supported from D3hot D3cold > [ 0.585261] pci 0000:00:08.0: PME# disabled > [ 1.926486] serial 0000:00:08.0: PCI INT A -> Link[C0CA] -> GSI 11 > (level, low) -> IRQ 11 > [ 1.926494] serial 0000:00:08.0: PCI INT A disabled > > The PCI slot 00:08.0 of the modem card may be disabled early in > a bootup process, but then enabled later. If modem drivers load > but the modem is not responsive, read DOCs/Bootup.txt about possible > fixes. > Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx > if help is needed. > > > For candidate card in slot 00:06.0, firmware information and bootup > diagnostics are: > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:06.0 10b9:5451 0e11:005a Multimedia audio controller: ALi > Corporation M5451 PCI AC-Link Controller Audio Device > > Modem interrupt assignment and sharing: > 11: 1904 XT-PIC-XT yenta, yenta, ALI 5451 > --- Bootup diagnostics for card in PCI slot 00:06.0 ---- > [ 0.585122] pci 0000:00:06.0: reg 10 io port: [0x3000-0x30ff] > [ 0.585128] pci 0000:00:06.0: reg 14 32bit mmio: [0x98080000-0x98080fff] > [ 0.585150] pci 0000:00:06.0: supports D1 D2 > [ 0.585154] pci 0000:00:06.0: PME# supported from D2 D3hot D3cold > [ 0.585159] pci 0000:00:06.0: PME# disabled > [ 13.063265] ALI 5451 0000:00:06.0: PCI INT A -> Link[C0CB] -> GSI > 11 (level, low) -> IRQ 11 > > The PCI slot 00:06.0 of the modem card may be disabled early in > a bootup process, but then enabled later. If modem drivers load > but the modem is not responsive, read DOCs/Bootup.txt about possible > fixes. > Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx > if help is needed. > > ==============dmesg.txt.============ > > CPU0 > 0: 502462 XT-PIC-XT timer > 1: 1738 XT-PIC-XT i8042 > 2: 0 XT-PIC-XT cascade > 4: 9 XT-PIC-XT > 5: 124 XT-PIC-XT yenta, pcmcia0.0 > 7: 2 XT-PIC-XT parport0 > 8: 0 XT-PIC-XT rtc0 > 9: 9252 XT-PIC-XT acpi > 10: 74314 XT-PIC-XT ehci_hcd:usb1, ohci_hcd:usb2, > ohci_hcd:usb3, radeon@pci:0000:01:05.0, eth0 > 11: 1904 XT-PIC-XT yenta, yenta, ALI 5451 > 12: 947433 XT-PIC-XT i8042 > 14: 50225 XT-PIC-XT pata_ali > 15: 0 XT-PIC-XT pata_ali > NMI: 0 Non-maskable interrupts > LOC: 0 Local timer interrupts > RES: 0 Rescheduling interrupts > CAL: 0 Function call interrupts > TLB: 0 TLB shootdowns > SPU: 0 Spurious interrupts > ERR: 0 > MIS: 0 > > [ 0.000000] BIOS EBDA/lowmem at: 0009fc00/0009fc00 > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 2.6.28-11-generic (buildd@palmer) (gcc > version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #42-Ubuntu SMP Fri Apr 17 > 01:57:59 UTC 2009 (Ubuntu 2.6.28-11.42-generic) > [ 0.000000] KERNEL supported cpus: > [ 0.000000] Intel GenuineIntel > [ 0.000000] AMD AuthenticAMD > [ 0.000000] NSC Geode by NSC > [ 0.000000] Cyrix CyrixInstead > [ 0.000000] Centaur CentaurHauls > [ 0.000000] Transmeta GenuineTMx86 > [ 0.000000] Transmeta TransmetaCPU > [ 0.000000] UMC UMC UMC UMC > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000001dfd0000 (usable) > [ 0.000000] BIOS-e820: 000000001dfd0000 - 000000001dff0c00 (reserved) > [ 0.000000] BIOS-e820: 000000001dff0c00 - 000000001dffc000 (ACPI NVS) > [ 0.000000] BIOS-e820: 000000001dffc000 - 000000001e000000 (reserved) > [ 0.000000] DMI 2.3 present. > [ 0.000000] last_pfn = 0x1dfd0 max_arch_pfn = 0x100000 > [ 0.000000] Scanning 2 areas for low memory corruption > [ 0.000000] modified physical RAM map: > [ 0.000000] modified: 0000000000000000 - 0000000000002000 (usable) > [ 0.000000] modified: 0000000000002000 - 0000000000006000 (reserved) > [ 0.000000] modified: 0000000000006000 - 0000000000007000 (usable) > [ 0.000000] modified: 0000000000007000 - 0000000000010000 (reserved) > [ 0.000000] modified: 0000000000010000 - 0000000000092c00 (usable) > [ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved) > [ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved) > [ 0.000000] modified: 0000000000100000 - 000000001dfd0000 (usable) > [ 0.000000] modified: 000000001dfd0000 - 000000001dff0c00 (reserved) > [ 0.000000] modified: 000000001dff0c00 - 000000001dffc000 (ACPI NVS) > [ 0.000000] modified: 000000001dffc000 - 000000001e000000 (reserved) > [ 0.000000] kernel direct mapping tables up to 1dfd0000 @ 10000-16000 > [ 0.000000] RAMDISK: 1d88d000 - 1dfbf152 > [ 0.000000] ACPI: RSDP 000F7840, 0014 (r0 COMPAQ) > [ 0.000000] ACPI: RSDT 1DFF0C84, 002C (r1 COMPAQ CPQ005A 30080620 > CPQ 1) > [ 0.000000] ACPI: FACP 1DFF0C00, 0084 (r2 COMPAQ CPQ005A 2 > CPQ 1) > [ 0.000000] ACPI: DSDT 1DFF0CB0, 607E (r1 COMPAQ EVON800 10000 > MSFT 100000E) > [ 0.000000] ACPI: FACS 1DFFBE80, 0040 > [ 0.000000] ACPI: SSDT 1DFF6D2E, 02A7 (r1 COMPAQ CPQGysr 1001 > MSFT 100000E) > [ 0.000000] 0MB HIGHMEM available. > [ 0.000000] 479MB LOWMEM available. > [ 0.000000] mapped low ram: 0 - 1dfd0000 > [ 0.000000] low ram: 00000000 - 1dfd0000 > [ 0.000000] bootmap 00012000 - 00015bfc > [ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 001dfd0000] > [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> > [0000000000 - 0000001000] > [ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> > [0000001000 - 0000002000] > [ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> > [0000006000 - 0000007000] > [ 0.000000] #3 [0000100000 - 000087c52c] TEXT DATA BSS ==> > [0000100000 - 000087c52c] > [ 0.000000] #4 [001d88d000 - 001dfbf152] RAMDISK ==> > [001d88d000 - 001dfbf152] > [ 0.000000] #5 [000087d000 - 0000881000] INIT_PG_TABLE ==> > [000087d000 - 0000881000] > [ 0.000000] #6 [000009fc00 - 0000100000] BIOS reserved ==> > [000009fc00 - 0000100000] > [ 0.000000] #7 [0000010000 - 0000012000] PGTABLE ==> > [0000010000 - 0000012000] > [ 0.000000] #8 [0000012000 - 0000016000] BOOTMAP ==> > [0000012000 - 0000016000] > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0x00000000 -> 0x00001000 > [ 0.000000] Normal 0x00001000 -> 0x0001dfd0 > [ 0.000000] HighMem 0x0001dfd0 -> 0x0001dfd0 > [ 0.000000] Movable zone start PFN for each node > [ 0.000000] early_node_map[4] active PFN ranges > [ 0.000000] 0: 0x00000000 -> 0x00000002 > [ 0.000000] 0: 0x00000006 -> 0x00000007 > [ 0.000000] 0: 0x00000010 -> 0x00000092 > [ 0.000000] 0: 0x00000100 -> 0x0001dfd0 > [ 0.000000] On node 0 totalpages: 122709 > [ 0.000000] free_area_init_node: node 0, pgdat c06d0f80, > node_mem_map c1000000 > [ 0.000000] DMA zone: 32 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 3941 pages, LIFO batch:0 > [ 0.000000] Normal zone: 928 pages used for memmap > [ 0.000000] Normal zone: 117808 pages, LIFO batch:31 > [ 0.000000] HighMem zone: 0 pages used for memmap > [ 0.000000] Movable zone: 0 pages used for memmap > [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 > [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs > [ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic" > [ 0.000000] PM: Registered nosave memory: 0000000000002000 - > 0000000000006000 > [ 0.000000] PM: Registered nosave memory: 0000000000007000 - > 0000000000010000 > [ 0.000000] PM: Registered nosave memory: 0000000000092000 - > 00000000000a0000 > [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - > 00000000000e0000 > [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - > 0000000000100000 > [ 0.000000] Allocating PCI resources starting at 20000000 (gap: > 1e000000:e2000000) > [ 0.000000] PERCPU: Allocating 45056 bytes of per cpu data > [ 0.000000] NR_CPUS: 64, nr_cpu_ids: 1, nr_node_ids 1 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 121749 > [ 0.000000] Kernel command line: > root=UUID=8e06cd56-d1ec-4db5-966d-b2cb059c67b0 ro quiet splash > [ 0.000000] Enabling fast FPU save and restore... done. > [ 0.000000] Enabling unmasked SIMD FPU exception support... done. > [ 0.000000] Initializing CPU#0 > [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes) > [ 0.000000] Fast TSC calibration using PIT > [ 0.000000] Detected 1592.099 MHz processor. > [ 0.004000] Console: colour VGA+ 80x25 > [ 0.004000] console [tty0] enabled > [ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 > bytes) > [ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 > bytes) > [ 0.004000] allocated 2456640 bytes of page_cgroup > [ 0.004000] please try cgroup_disable=memory option if you don't want > [ 0.004000] Scanning for low memory corruption every 60 seconds > [ 0.004000] Memory: 468840k/491328k available (4126k kernel code, > 21792k reserved, 2208k data, 532k init, 0k highmem) > [ 0.004000] virtual kernel memory layout: > [ 0.004000] fixmap : 0xffc77000 - 0xfffff000 (3616 kB) > [ 0.004000] pkmap : 0xff400000 - 0xff800000 (4096 kB) > [ 0.004000] vmalloc : 0xde7d0000 - 0xff3fe000 ( 524 MB) > [ 0.004000] lowmem : 0xc0000000 - 0xddfd0000 ( 479 MB) > [ 0.004000] .init : 0xc0737000 - 0xc07bc000 ( 532 kB) > [ 0.004000] .data : 0xc0507a6f - 0xc072fe60 (2208 kB) > [ 0.004000] .text : 0xc0100000 - 0xc0507a6f (4126 kB) > [ 0.004000] Checking if this processor honours the WP bit even in > supervisor mode...Ok. > [ 0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, > CPUs=1, Nodes=1 > [ 0.004023] Calibrating delay loop (skipped), value calculated > using timer frequency.. 3184.19 BogoMIPS (lpj=6368396) > [ 0.004058] Security Framework initialized > [ 0.004079] SELinux: Disabled at boot. > [ 0.004117] AppArmor: AppArmor initialized > [ 0.004131] Mount-cache hash table entries: 512 > [ 0.004373] Initializing cgroup subsys ns > [ 0.004382] Initializing cgroup subsys cpuacct > [ 0.004386] Initializing cgroup subsys memory > [ 0.004392] Initializing cgroup subsys freezer > [ 0.004421] CPU: L1 I cache: 32K, L1 D cache: 32K > [ 0.004424] CPU: L2 cache: 2048K > [ 0.004451] Checking 'hlt' instruction... OK. > [ 0.021208] SMP alternatives: switching to UP code > [ 0.144485] Freeing SMP alternatives: 18k freed > [ 0.144490] ACPI: Core revision 20080926 > [ 0.152957] ACPI: Checking initramfs for custom DSDT > [ 0.532952] ACPI: setting ELCR to 0200 (from 0c20) > [ 0.536171] weird, boot CPU (#0) not listedby the BIOS. > [ 0.536179] SMP motherboard not detected. > [ 0.536184] Local APIC not detected. Using dummy APIC emulation. > [ 0.536187] SMP disabled > [ 0.540172] Brought up 1 CPUs > [ 0.540176] Total of 1 processors activated (3184.19 BogoMIPS). > [ 0.540200] CPU0 attaching NULL sched-domain. > [ 0.540732] net_namespace: 776 bytes > [ 0.540752] HP Compaq Laptop series board detected. Selecting > BIOS-method for reboots. > [ 0.540757] Booting paravirtualized kernel on bare hardware > [ 0.541050] Time: 6:51:04 Date: 06/18/09 > [ 0.541059] regulator: core version 0.5 > [ 0.541119] NET: Registered protocol family 16 > [ 0.541306] EISA bus registered > [ 0.541331] ACPI: bus type pci registered > [ 0.544159] PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=1 > [ 0.544162] PCI: Using configuration type 1 for base access > [ 0.546246] ACPI: EC: Look up EC in DSDT > [ 0.562553] ACPI: EC: non-query interrupt received, switching to > interrupt mode > [ 0.568190] ACPI: Interpreter enabled > [ 0.568199] ACPI: (supports S0 S3 S4 S5) > [ 0.568219] ACPI: Using PIC for interrupt routing > [ 0.584815] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62 > [ 0.584819] ACPI: EC: driver started in interrupt mode > [ 0.584986] ACPI: No dock devices found. > [ 0.584997] ACPI: PCI Root Bridge [C044] (0000:00) > [ 0.585053] pci 0000:00:00.0: reg 10 32bit mmio: [0x9c000000-0x9fffffff] > [ 0.585058] pci 0000:00:00.0: reg 14 32bit mmio: [0x98500000-0x98500fff] > [ 0.585122] pci 0000:00:06.0: reg 10 io port: [0x3000-0x30ff] > [ 0.585128] pci 0000:00:06.0: reg 14 32bit mmio: [0x98080000-0x98080fff] > [ 0.585150] pci 0000:00:06.0: supports D1 D2 > [ 0.585154] pci 0000:00:06.0: PME# supported from D2 D3hot D3cold > [ 0.585159] pci 0000:00:06.0: PME# disabled > [ 0.585229] pci 0000:00:08.0: reg 10 32bit mmio: [0x98100000-0x98100fff] > [ 0.585235] pci 0000:00:08.0: reg 14 io port: [0x3400-0x34ff] > [ 0.585257] pci 0000:00:08.0: PME# supported from D3hot D3cold > [ 0.585261] pci 0000:00:08.0: PME# disabled > [ 0.585286] pci 0000:00:09.0: reg 10 32bit mmio: [0x98180000-0x98180fff] > [ 0.585294] pci 0000:00:09.0: supports D1 D2 > [ 0.585296] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.585300] pci 0000:00:09.0: PME# disabled > [ 0.585328] pci 0000:00:0b.0: reg 10 32bit mmio: [0x98200000-0x98200fff] > [ 0.585336] pci 0000:00:0b.0: supports D1 D2 > [ 0.585338] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.585342] pci 0000:00:0b.0: PME# disabled > [ 0.585368] pci 0000:00:0b.1: reg 10 32bit mmio: [0x98280000-0x98280fff] > [ 0.585376] pci 0000:00:0b.1: supports D1 D2 > [ 0.585378] pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.585383] pci 0000:00:0b.1: PME# disabled > [ 0.585408] pci 0000:00:0b.2: reg 10 32bit mmio: [0x98300000-0x98300fff] > [ 0.585435] pci 0000:00:0b.2: supports D1 D2 > [ 0.585438] pci 0000:00:0b.2: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.585442] pci 0000:00:0b.2: PME# disabled > [ 0.585483] pci 0000:00:10.0: reg 20 io port: [0x3800-0x380f] > [ 0.585538] pci 0000:00:11.0: quirk: region 1000-103f claimed by ali7101 > ACPI > [ 0.585542] pci 0000:00:11.0: quirk: region 1100-111f claimed by ali7101 > SMB > [ 0.585565] pci 0000:00:12.0: reg 10 32bit mmio: [0x98380000-0x98380fff] > [ 0.585590] pci 0000:00:12.0: supports D1 D2 > [ 0.585592] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.585596] pci 0000:00:12.0: PME# disabled > [ 0.585619] pci 0000:00:12.1: reg 10 32bit mmio: [0x98400000-0x98400fff] > [ 0.585644] pci 0000:00:12.1: supports D1 D2 > [ 0.585647] pci 0000:00:12.1: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.585651] pci 0000:00:12.1: PME# disabled > [ 0.585674] pci 0000:00:12.2: reg 10 32bit mmio: [0x98480000-0x984800ff] > [ 0.585699] pci 0000:00:12.2: supports D1 D2 > [ 0.585701] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.585705] pci 0000:00:12.2: PME# disabled > [ 0.585751] pci 0000:00:13.0: reg 10 64bit mmio: [0x98000000-0x9800ffff] > [ 0.585772] pci 0000:00:13.0: reg 30 32bit mmio: [0x000000-0x00ffff] > [ 0.585781] pci 0000:00:13.0: PME# supported from D3hot D3cold > [ 0.585785] pci 0000:00:13.0: PME# disabled > [ 0.585833] pci 0000:01:05.0: reg 10 32bit mmio: [0x94000000-0x97ffffff] > [ 0.585839] pci 0000:01:05.0: reg 14 io port: [0x2000-0x20ff] > [ 0.585844] pci 0000:01:05.0: reg 18 32bit mmio: [0x90000000-0x9000ffff] > [ 0.585858] pci 0000:01:05.0: reg 30 32bit mmio: [0x000000-0x01ffff] > [ 0.585867] pci 0000:01:05.0: supports D1 D2 > [ 0.585896] pci 0000:00:01.0: bridge io port: [0x2000-0x2fff] > [ 0.585901] pci 0000:00:01.0: bridge 32bit mmio: [0x90000000-0x900fffff] > [ 0.585905] pci 0000:00:01.0: bridge 32bit mmio pref: > [0x94000000-0x97ffffff] > [ 0.585946] bus 00 -> node 0 > [ 0.585955] ACPI: PCI Interrupt Routing Table [\_SB_.C044._PRT] > [ 0.586068] ACPI: PCI Interrupt Routing Table [\_SB_.C044.C045._PRT] > [ 0.615493] ACPI: PCI Interrupt Link [C0C4] (IRQs 5 *10 11) > [ 0.615728] ACPI: PCI Interrupt Link [C0C5] (IRQs 5 *10 11) > [ 0.615954] ACPI: PCI Interrupt Link [C0C6] (IRQs 5 10 *11) > [ 0.616162] ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10 11) *0, disabled. > [ 0.616388] ACPI: PCI Interrupt Link [C0C8] (IRQs 5 *10 11) > [ 0.616612] ACPI: PCI Interrupt Link [C0C9] (IRQs *5 10 11) > [ 0.616836] ACPI: PCI Interrupt Link [C0CA] (IRQs 5 10 *11) > [ 0.617060] ACPI: PCI Interrupt Link [C0CB] (IRQs 5 10 *11) > [ 0.617450] ACPI: Power Resource [C15A] (on) > [ 0.617764] ACPI: Power Resource [C15F] (on) > [ 0.618076] ACPI: Power Resource [C169] (on) > [ 0.618125] ACPI: Power Resource [C17A] (on) > [ 0.618227] ACPI: Power Resource [C1F2] (off) > [ 0.618324] ACPI: Power Resource [C1F3] (off) > [ 0.618420] ACPI: Power Resource [C1F4] (off) > [ 0.618517] ACPI: Power Resource [C1F5] (off) > [ 0.618626] ACPI: WMI: Mapper loaded > [ 0.618833] SCSI subsystem initialized > [ 0.618885] libata version 3.00 loaded. > [ 0.618951] usbcore: registered new interface driver usbfs > [ 0.618971] usbcore: registered new interface driver hub > [ 0.619004] usbcore: registered new device driver usb > [ 0.619145] PCI: Using ACPI for IRQ routing > [ 0.619239] Bluetooth: Core ver 2.13 > [ 0.619239] NET: Registered protocol family 31 > [ 0.619239] Bluetooth: HCI device and connection manager initialized > [ 0.619239] Bluetooth: HCI socket layer initialized > [ 0.619239] NET: Registered protocol family 8 > [ 0.619239] NET: Registered protocol family 20 > [ 0.619239] NetLabel: Initializing > [ 0.619239] NetLabel: domain hash size = 128 > [ 0.619239] NetLabel: protocols = UNLABELED CIPSOv4 > [ 0.619239] NetLabel: unlabeled traffic allowed by default > [ 0.619239] AppArmor: AppArmor Filesystem Enabled > [ 0.619239] pnp: PnP ACPI init > [ 0.619239] ACPI: bus type pnp registered > [ 0.639488] pnp: PnP ACPI: found 14 devices > [ 0.639491] ACPI: ACPI bus type pnp unregistered > [ 0.639497] PnPBIOS: Disabled by ACPI PNP > [ 0.639509] system 00:00: iomem range 0x0-0x9ffff could not be reserved > [ 0.639512] system 00:00: iomem range 0xe0000-0xfffff could not be > reserved > [ 0.639516] system 00:00: iomem range 0x100000-0x1dffffff could not > be reserved > [ 0.639527] system 00:0b: ioport range 0x370-0x371 has been reserved > [ 0.639530] system 00:0b: ioport range 0x40b-0x40b has been reserved > [ 0.639533] system 00:0b: ioport range 0x480-0x48f has been reserved > [ 0.639536] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved > [ 0.639539] system 00:0b: ioport range 0x4d6-0x4d6 has been reserved > [ 0.639543] system 00:0b: ioport range 0x1400-0x141f has been reserved > [ 0.639546] system 00:0b: iomem range 0xffb00000-0xffbfffff has been > reserved > [ 0.639550] system 00:0b: iomem range 0xfff00000-0xffffffff has been > reserved > [ 0.639556] system 00:0c: ioport range 0x1000-0x107f could not be > reserved > [ 0.639559] system 00:0c: ioport range 0x1100-0x111f has been reserved > [ 0.639563] system 00:0c: iomem range 0x98500000-0x98500fff has been > reserved > [ 0.639569] system 00:0d: iomem range 0xcf000-0xcffff has been reserved > [ 0.674312] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 > [ 0.674315] pci 0000:00:01.0: IO window: 0x2000-0x2fff > [ 0.674320] pci 0000:00:01.0: MEM window: 0x90000000-0x900fffff > [ 0.674325] pci 0000:00:01.0: PREFETCH window: > 0x00000094000000-0x00000097ffffff > [ 0.674331] pci 0000:00:09.0: CardBus bridge, secondary bus 0000:02 > [ 0.674333] pci 0000:00:09.0: IO window: 0x001800-0x0018ff > [ 0.674338] pci 0000:00:09.0: IO window: 0x001c00-0x001cff > [ 0.674342] pci 0000:00:09.0: PREFETCH window: 0x20000000-0x23ffffff > [ 0.674346] pci 0000:00:09.0: MEM window: 0x24000000-0x27ffffff > [ 0.674350] pci 0000:00:0b.0: CardBus bridge, secondary bus 0000:06 > [ 0.674353] pci 0000:00:0b.0: IO window: 0x003c00-0x003cff > [ 0.674357] pci 0000:00:0b.0: IO window: 0x004000-0x0040ff > [ 0.674361] pci 0000:00:0b.0: PREFETCH window: 0x28000000-0x2bffffff > [ 0.674365] pci 0000:00:0b.0: MEM window: 0x2c000000-0x2fffffff > [ 0.674369] pci 0000:00:0b.1: CardBus bridge, secondary bus 0000:0a > [ 0.674372] pci 0000:00:0b.1: IO window: 0x004400-0x0044ff > [ 0.674375] pci 0000:00:0b.1: IO window: 0x004800-0x0048ff > [ 0.674380] pci 0000:00:0b.1: PREFETCH window: 0x30000000-0x33ffffff > [ 0.674384] pci 0000:00:0b.1: MEM window: 0x34000000-0x37ffffff > [ 0.674827] ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5 > [ 0.674830] PCI: setting IRQ 5 as level-triggered > [ 0.674835] pci 0000:00:09.0: PCI INT A -> Link[C0C9] -> GSI 5 > (level, low) -> IRQ 5 > [ 0.675249] ACPI: PCI Interrupt Link [C0C6] enabled at IRQ 11 > [ 0.675252] PCI: setting IRQ 11 as level-triggered > [ 0.675256] pci 0000:00:0b.0: PCI INT A -> Link[C0C6] -> GSI 11 > (level, low) -> IRQ 11 > [ 0.675266] pci 0000:00:0b.1: PCI INT A -> Link[C0C6] -> GSI 11 > (level, low) -> IRQ 11 > [ 0.675271] bus: 00 index 0 io port: [0x00-0xffff] > [ 0.675274] bus: 00 index 1 mmio: [0x000000-0xffffffff] > [ 0.675277] bus: 01 index 0 io port: [0x2000-0x2fff] > [ 0.675279] bus: 01 index 1 mmio: [0x90000000-0x900fffff] > [ 0.675282] bus: 01 index 2 mmio: [0x94000000-0x97ffffff] > [ 0.675285] bus: 01 index 3 mmio: [0x0-0x0] > [ 0.675287] bus: 02 index 0 io port: [0x1800-0x18ff] > [ 0.675290] bus: 02 index 1 io port: [0x1c00-0x1cff] > [ 0.675292] bus: 02 index 2 mmio: [0x20000000-0x23ffffff] > [ 0.675295] bus: 02 index 3 mmio: [0x24000000-0x27ffffff] > [ 0.675298] bus: 06 index 0 io port: [0x3c00-0x3cff] > [ 0.675300] bus: 06 index 1 io port: [0x4000-0x40ff] > [ 0.675303] bus: 06 index 2 mmio: [0x28000000-0x2bffffff] > [ 0.675305] bus: 06 index 3 mmio: [0x2c000000-0x2fffffff] > [ 0.675308] bus: 0a index 0 io port: [0x4400-0x44ff] > [ 0.675310] bus: 0a index 1 io port: [0x4800-0x48ff] > [ 0.675313] bus: 0a index 2 mmio: [0x30000000-0x33ffffff] > [ 0.675316] bus: 0a index 3 mmio: [0x34000000-0x37ffffff] > [ 0.675327] NET: Registered protocol family 2 > [ 0.675459] IP route cache hash table entries: 4096 (order: 2, 16384 > bytes) > [ 0.675741] TCP established hash table entries: 16384 (order: 5, > 131072 bytes) > [ 0.675931] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) > [ 0.676131] TCP: Hash tables configured (established 16384 bind 16384) > [ 0.676135] TCP reno registered > [ 0.676217] NET: Registered protocol family 1 > [ 0.676401] checking if image is initramfs... it is > [ 1.176115] Switched to high resolution mode on CPU 0 > [ 1.466194] Freeing initrd memory: 7368k freed > [ 1.466381] cpufreq: No nForce2 chipset. > [ 1.466678] audit: initializing netlink socket (disabled) > [ 1.466728] type=2000 audit(1245307864.464:1): initialized > [ 1.476168] HugeTLB registered 4 MB page size, pre-allocated 0 pages > [ 1.477805] VFS: Disk quotas dquot_6.5.1 > [ 1.477877] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 1.478687] fuse init (API version 7.10) > [ 1.478802] msgmni has been set to 930 > [ 1.479125] alg: No test for stdrng (krng) > [ 1.479146] io scheduler noop registered > [ 1.479148] io scheduler anticipatory registered > [ 1.479151] io scheduler deadline registered > [ 1.479170] io scheduler cfq registered (default) > [ 1.479216] pci 0000:00:07.0: Activating ISA DMA hang workarounds > [ 1.479313] pci 0000:01:05.0: Boot video device > [ 1.488417] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 1.488429] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 > [ 1.491393] ACPI: AC Adapter [C137] (on-line) > [ 1.533904] ACPI: Battery Slot [C139] (battery present) > [ 1.534171] ACPI: Battery Slot [C138] (battery absent) > [ 1.534269] input: Power Button (FF) as > /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 > [ 1.534272] ACPI: Power Button (FF) [PWRF] > [ 1.534337] input: Sleep Button (CM) as > /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 > [ 1.534340] ACPI: Sleep Button (CM) [C13B] > [ 1.534399] input: Lid Switch as > /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2 > [ 1.534483] ACPI: Lid Switch [C13A] > [ 1.534733] fan PNP0C0B:00: registered as cooling_device0 > [ 1.534740] ACPI: Fan [C1F6] (off) > [ 1.534939] fan PNP0C0B:01: registered as cooling_device1 > [ 1.534945] ACPI: Fan [C1F7] (off) > [ 1.535144] fan PNP0C0B:02: registered as cooling_device2 > [ 1.535150] ACPI: Fan [C1F8] (off) > [ 1.535348] fan PNP0C0B:03: registered as cooling_device3 > [ 1.535354] ACPI: Fan [C1F9] (off) > [ 1.535510] ACPI: Invalid PBLK length [7] > [ 1.535741] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3]) > [ 1.535763] processor ACPI_CPU:00: registered as cooling_device4 > [ 1.546872] thermal LNXTHERM:01: registered as thermal_zone0 > [ 1.550304] ACPI: Thermal Zone [TZ1] (54 C) > [ 1.553562] thermal LNXTHERM:02: registered as thermal_zone1 > [ 1.555852] ACPI: Thermal Zone [TZ2] (44 C) > [ 1.561542] thermal LNXTHERM:03: registered as thermal_zone2 > [ 1.569908] ACPI: Thermal Zone [TZ3] (32 C) > [ 1.569966] isapnp: Scanning for PnP cards... > [ 1.923817] isapnp: No Plug & Play device found > [ 1.925167] Serial: 8250/16550 driver4 ports, IRQ sharing enabled > [ 1.925296] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 1.925454] serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A > [ 1.925730] 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 1.926479] ACPI: PCI Interrupt Link [C0CA] enabled at IRQ 11 > [ 1.926486] serial 0000:00:08.0: PCI INT A -> Link[C0CA] -> GSI 11 > (level, low) -> IRQ 11 > [ 1.926494] serial 0000:00:08.0: PCI INT A disabled > [ 1.927376] brd: module loaded > [ 1.927783] loop: module loaded > [ 1.927877] Fixed MDIO Bus: probed > [ 1.927887] PPP generic driver version 2.4.2 > [ 1.927965] input: Macintosh mouse button emulation as > /devices/virtual/input/input3 > [ 1.928007] Driver 'sd' needs updating - please use bus_type methods > [ 1.928045] Driver 'sr' needs updating - please use bus_type methods > [ 1.928781] ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 10 > [ 1.928785] PCI: setting IRQ 10 as level-triggered > [ 1.928789] pata_ali 0000:00:10.0: PCI INT A -> Link[C0C4] -> GSI > 10 (level, low) -> IRQ 10 > [ 1.929020] scsi0 : pata_ali > [ 1.929138] scsi1 : pata_ali > [ 1.929688] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x3800 irq > 14 > [ 1.929692] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x3808 irq > 15 > [ 2.092305] ata1.00: ATA-6: ST960822A, 3.02, max UDMA/100 > [ 2.092308] ata1.00: 117210240 sectors, multi 16: LBA48 > [ 2.108249] ata1.00: configured for UDMA/100 > [ 2.264336] scsi 0:0:0:0: Direct-Access ATA ST960822A > 3.02 PQ: 0 ANSI: 5 > [ 2.264464] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: > (60.0 GB/55.8 GiB) > [ 2.264488] sd 0:0:0:0: [sda] Write Protect is off > [ 2.264491] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 2.264523] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > [ 2.264604] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: > (60.0 GB/55.8 GiB) > [ 2.264621] sd 0:0:0:0: [sda] Write Protect is off > [ 2.264623] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 2.264650] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > [ 2.264656] sda: sda1 sda2 < sda5 > > [ 2.316672] sd 0:0:0:0: [sda] Attached SCSI disk > [ 2.316728] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 2.317423] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > [ 2.317893] ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 10 > [ 2.317899] ehci_hcd 0000:00:12.2: PCI INT C -> Link[C0C5] -> GSI > 10 (level, low) -> IRQ 10 > [ 2.317943] ehci_hcd 0000:00:12.2: EHCI Host Controller > [ 2.318045] ehci_hcd 0000:00:12.2: new USB bus registered, assigned > bus number 1 > [ 2.340059] ehci_hcd 0000:00:12.2: irq 10, io mem 0x98480000 > [ 2.352040] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00 > [ 2.352147] usb usb1: configuration #1 chosen from 1 choice > [ 2.352186] hub 1-0:1.0: USB hub found > [ 2.352202] hub 1-0:1.0: 5 ports detected > [ 2.352334] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > [ 2.352354] ohci_hcd 0000:00:12.0: PCI INT A -> Link[C0C5] -> GSI > 10 (level, low) -> IRQ 10 > [ 2.352375] ohci_hcd 0000:00:12.0: OHCI Host Controller > [ 2.352422] ohci_hcd 0000:00:12.0: new USB bus registered, assigned > bus number 2 > [ 2.352441] ohci_hcd 0000:00:12.0: irq 10, io mem 0x98380000 > [ 2.437878] usb usb2: configuration #1 chosen from 1 choice > [ 2.437906] hub 2-0:1.0: USB hub found > [ 2.437931] hub 2-0:1.0: 3 ports detected > [ 2.438019] ohci_hcd 0000:00:12.1: PCI INT B -> Link[C0C5] -> GSI > 10 (level, low) -> IRQ 10 > [ 2.438030] ohci_hcd 0000:00:12.1: OHCI Host Controller > [ 2.438087] ohci_hcd 0000:00:12.1: new USB bus registered, assigned > bus number 3 > [ 2.438104] ohci_hcd 0000:00:12.1: irq 10, io mem 0x98400000 > [ 2.521870] usb usb3: configuration #1 chosen from 1 choice > [ 2.521898] hub 3-0:1.0: USB hub found > [ 2.521911] hub 3-0:1.0: 2 ports detected > [ 2.522018] uhci_hcd: USB Universal Host Controller Interface driver > [ 2.522104] usbcore: registered new interface driver libusual > [ 2.522149] usbcore: registered new interface driver usbserial > [ 2.522163] USB Serial support registered for generic > [ 2.522181] usbcore: registered new interface driver usbserial_generic > [ 2.522183] usbserial: USB Serial Driver core > [ 2.522252] PNP: PS/2 Controller [PNP0303:C177,PNP0f13:C178] at > 0x60,0x64 irq 1,12 > [ 2.524084] i8042.c: Detected active multiplexing controller, rev 1.1. > [ 2.524825] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 2.524834] serio: i8042 AUX0 port at 0x60,0x64 irq 12 > [ 2.524837] serio: i8042 AUX1 port at 0x60,0x64 irq 12 > [ 2.524840] serio: i8042 AUX2 port at 0x60,0x64 irq 12 > [ 2.524842] serio: i8042 AUX3 port at 0x60,0x64 irq 12 > [ 2.525033] mice: PS/2 mouse device common for all mice > [ 2.525246] rtc_cmos 00:08: RTC can wake from S4 > [ 2.525298] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 > [ 2.525330] rtc0: alarms up to one month, y3k, 114 bytes nvram > [ 2.525410] device-mapper: uevent: version 1.0.3 > [ 2.525562] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) > initialised: dm-devel@xxxxxxxxxx > [ 2.525628] device-mapper: multipath: version 1.0.5 loaded > [ 2.525632] device-mapper: multipath round-robin: version 1.0.0 loaded > [ 2.525749] EISA: Probing bus 0 at eisa.0 > [ 2.525762] Cannot allocate resource for EISA slot 1 > [ 2.525765] Cannot allocate resource for EISA slot 2 > [ 2.525767] Cannot allocate resource for EISA slot 3 > [ 2.525770] Cannot allocate resource for EISA slot 4 > [ 2.525792] EISA: Detected 0 cards. > [ 2.525884] cpuidle: using governor ladder > [ 2.525974] cpuidle: using governor menu > [ 2.526576] TCP cubic registered > [ 2.526709] NET: Registered protocol family 10 > [ 2.527228] lo: Disabled Privacy Extensions > [ 2.527583] NET: Registered protocol family 17 > [ 2.527605] Bluetooth: L2CAP ver 2.11 > [ 2.527608] Bluetooth: L2CAP socket layer initialized > [ 2.527611] Bluetooth: SCO (Voice Link) ver 0.6 > [ 2.527613] Bluetooth: SCO socket layer initialized > [ 2.527650] Bluetooth: RFCOMM socket layer initialized > [ 2.527661] Bluetooth: RFCOMM TTY layer initialized > [ 2.527663] Bluetooth: RFCOMM ver 1.10 > [ 2.527962] IO APIC resources could be not be allocated. > [ 2.528034] Using IPI No-Shortcut mode > [ 2.528140] registered taskstats version 1 > [ 2.528278] Magic number: 13:325:873 > [ 2.528437] rtc_cmos 00:08: setting system clock to 2009-06-18 > 06:51:06 UTC (1245307866) > [ 2.528442] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found > [ 2.528444] EDD information not available. > [ 2.529244] Freeing unused kernel memory: 532k freed > [ 2.529406] Write protecting the kernel text: 4128k > [ 2.529452] Write protecting the kernel read-only data: 1532k > [ 2.565688] input: AT Translated Set 2 keyboard as > /devices/platform/i8042/serio0/input/input4 > [ 3.627338] tg3.c:v3.94 (August 14, 2008) > [ 3.627927] ACPI: PCI Interrupt Link [C0C8] enabled at IRQ 10 > [ 3.627935] tg3 0000:00:13.0: PCI INT A -> Link[C0C8] -> GSI 10 > (level, low) -> IRQ 10 > [ 3.699687] eth0: Tigon3 [partno(BCM5705mA1) rev 3003 PHY(5705)] > (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:11:85:89:79:a6 > [ 3.699695] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] > WireSpeed[0] TSOcap[1] > [ 3.699698] eth0: dma_rwctrl[763f0000] dma_mask[64-bit] > [ 4.047217] Marking TSC unstable due to TSC halts in idle > [ 4.103845] PM: Starting manual resume from disk > [ 4.103850] PM: Resume from partition 8:5 > [ 4.103852] PM: Checking hibernation image. > [ 4.104052] PM: Resume from disk failed. > [ 4.146065] kjournald starting. Commit interval 5 seconds > [ 4.146083] EXT3-fs: mounted filesystem with ordered data mode. > [ 11.733262] udev: starting version 141 > [ 12.339240] yenta_cardbus 0000:00:09.0: CardBus bridge found [0000:0000] > [ 12.339261] yenta_cardbus 0000:00:09.0: Enabling burst memory read > transactions > [ 12.339266] yenta_cardbus 0000:00:09.0: Using CSCINT to route CSC > interrupts to PCI > [ 12.339269] yenta_cardbus 0000:00:09.0: Routing CardBus interrupts to PCI > [ 12.339274] yenta_cardbus 0000:00:09.0: TI: mfunc 0x00000000, devctl 0x66 > [ 12.387625] Linux agpgart interface v0.103 > [ 12.440058] yenta_cardbus 0000:00:09.0: TI: probing PCI interrupt > failed, trying to fix > [ 12.544302] yenta_cardbus 0000:00:09.0: TI: falling back to > parallel PCI interrupts > [ 12.648050] yenta_cardbus 0000:00:09.0: TI: parallel PCI interrupts ok > [ 12.735316] input: PC Speaker as /devices/platform/pcspkr/input/input5 > [ 12.779109] parport_pc 00:04: reported by Plug and Play ACPI > [ 12.779184] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 > [PCSPP,TRISTATE,COMPAT,ECP,DMA] > [ 12.781809] yenta_cardbus 0000:00:09.0: ISA IRQ mask 0x0000, PCI irq 5 > [ 12.781813] yenta_cardbus 0000:00:09.0: Socket status: 30000010 > [ 12.784791] ACPI: I/O resource ali1535_smbus [0x1100-0x111f] > conflicts with ACPI region C092 [0x1100-0x1107] > [ 12.784796] ACPI: Device needs an ACPI driver > [ 12.784987] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > [ 12.785078] yenta_cardbus 0000:00:0b.0: CardBus bridge found [0001:0000] > [ 12.785095] yenta_cardbus 0000:00:0b.0: O2: res at 0x94/0xD4: 00/ea > [ 12.785098] yenta_cardbus 0000:00:0b.0: O2: enabling read > prefetch/write burst > [ 12.792775] input: Video Bus as > /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/device:02/input/input6 > [ 12.795943] ACPI: Video Device [C046] (multi-head: yes rom: no post: > no) > [ 12.809547] ppdev: user-space parallel port driver > [ 12.913349] yenta_cardbus 0000:00:0b.0: ISA IRQ mask 0x0000, PCI irq 11 > [ 12.913357] yenta_cardbus 0000:00:0b.0: Socket status: 30000006 > [ 12.913946] agpgart-ati 0000:00:00.0: Ati IGP345M chipset > [ 12.931653] agpgart-ati 0000:00:00.0: AGP aperture is 64M @ 0x9c000000 > [ 12.931758] yenta_cardbus 0000:00:0b.1: CardBus bridge found [0001:0000] > [ 13.007896] synaptics was reset on resume, see > synaptics_resume_reset if you have trouble on resume > [ 13.061309] yenta_cardbus 0000:00:0b.1: ISA IRQ mask 0x0000, PCI irq 11 > [ 13.061316] yenta_cardbus 0000:00:0b.1: Socket status: 30000006 > [ 13.063257] ACPI: PCI Interrupt Link [C0CB] enabled at IRQ 11 > [ 13.063265] ALI 5451 0000:00:06.0: PCI INT A -> Link[C0CB] -> GSI > 11 (level, low) -> IRQ 11 > [ 13.420272] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card > inserted into slot 0 > [ 13.672278] Clocksource tsc unstable (delta = -358724137 ns) > [ 13.971842] pcmcia_socket pcmcia_socket1: cs: IO port probe > 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f > [ 13.974038] pcmcia_socket pcmcia_socket1: cs: IO port probe > 0x3e0-0x4ff: clean. > [ 13.974872] pcmcia_socket pcmcia_socket1: cs: IO port probe > 0x820-0x8ff: clean. > [ 13.975671] pcmcia_socket pcmcia_socket1: cs: IO port probe > 0xc00-0xcf7: clean. > [ 13.976698] pcmcia_socket pcmcia_socket1: cs: IO port probe > 0xa00-0xaff: clean. > [ 13.978148] pcmcia_socket pcmcia_socket2: cs: IO port probe > 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f > [ 13.980331] pcmcia_socket pcmcia_socket2: cs: IO port probe > 0x3e0-0x4ff: clean. > [ 13.981164] pcmcia_socket pcmcia_socket2: cs: IO port probe > 0x820-0x8ff: clean. > [ 13.981964] pcmcia_socket pcmcia_socket2: cs: IO port probe > 0xc00-0xcf7: clean. > [ 13.982954] pcmcia_socket pcmcia_socket2: cs: IO port probe > 0xa00-0xaff: clean. > [ 14.021449] pcmcia_socket pcmcia_socket0: cs: IO port probe > 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f > [ 14.023638] pcmcia_socket pcmcia_socket0: cs: IO port probe > 0x3e0-0x4ff: clean. > [ 14.024499] pcmcia_socket pcmcia_socket0: cs: IO port probe > 0x820-0x8ff: clean. > [ 14.025299] pcmcia_socket pcmcia_socket0: cs: IO port probe > 0xc00-0xcf7: clean. > [ 14.026291] pcmcia_socket pcmcia_socket0: cs: IO port probe > 0xa00-0xaff: clean. > [ 14.027205] pcmcia_socket pcmcia_socket0: cs: memory probe > 0xa0000000-0xa0ffffff: clean. > [ 14.034486] pcmcia 0.0: pcmcia: registering new device pcmcia0.0 > [ 14.056971] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1b6eb1, > caps: 0xa84793/0x100000 > [ 14.056980] serio: Synaptics pass-through port at isa0060/serio4/input0 > [ 14.105913] input: SynPS/2 Synaptics TouchPad as > /devices/platform/i8042/serio4/input/input7 > [ 14.163112] orinoco 0.15 (David Gibson > <hermes@xxxxxxxxxxxxxxxxxxxxx>, Pavel Roskin <proski@xxxxxxx>, et al) > [ 14.180460] orinoco_cs 0.15 (David Gibson > <hermes@xxxxxxxxxxxxxxxxxxxxx>, Pavel Roskin <proski@xxxxxxx>, et al) > [ 14.271692] eth1: Hardware identity 0005:0004:0005:0000 > [ 14.271803] eth1: Station identity 001f:0001:0008:000a > [ 14.271807] eth1: Firmware determined as Lucent/Agere 8.10 > [ 14.271812] eth1: Attempting to download firmware agere_sta_fw.bin > [ 14.271833] hermes_dld: AUX enable returned 0 > [ 14.272634] hermes_dld: AUX disable returned 0 > [ 14.272636] hermes_dld: Actual PDA length 998, Max allowed 1000 > [ 14.272639] eth1: Read PDA returned 0 > [ 14.272646] orinoco_cs 0.0: firmware: requesting agere_sta_fw.bin > [ 14.307167] eth1: Cannot find firmware agere_sta_fw.bin > [ 14.307224] eth1: Hardware identity 0005:0004:0005:0000 > [ 14.307330] eth1: Station identity 001f:0001:0008:000a > [ 14.307334] eth1: Firmware determined as Lucent/Agere 8.10 > [ 14.307336] eth1: Ad-hoc demo mode supported > [ 14.307339] eth1: IEEE standard IBSS ad-hoc mode supported > [ 14.307341] eth1: WEP supported, 104-bit key > [ 14.307427] eth1: MAC address 00:02:2d:bb:71:eb > [ 14.307513] eth1: Station name "HERMES I" > [ 14.308060] eth1: ready > [ 14.308883] eth1: orinoco_cs at 0.0, irq 5, io 0x0100-0x013f > [ 15.579802] synaptics was reset on resume, see > synaptics_resume_reset if you have trouble on resume > [ 17.650238] psmouse serio5: ID: 10 00 64<4>AC'97 1 does not respond - > RESET > [ 17.864267] AC'97 1 access is not valid [0xffffffff], removing mixer. > [ 17.864276] ali mixer 1 creating error. > [ 18.037789] lp0: using parport0 (interrupt-driven). > [ 18.110700] Adding 1397612k swap on /dev/sda5. Priority:-1 > extents:1 across:1397612k > [ 18.650394] EXT3 FS on sda1, internal journal > [ 19.719312] type=1505 audit(1245307883.687:2): > operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" > name2="default" pid=1948 > [ 19.783309] type=1505 audit(1245307883.751:3): > operation="profile_load" name="/sbin/dhclient-script" name2="default" > pid=1952 > [ 19.783550] type=1505 audit(1245307883.751:4): > operation="profile_load" name="/sbin/dhclient3" name2="default" > pid=1952 > [ 19.783631] type=1505 audit(1245307883.751:5): > operation="profile_load" > name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" > pid=1952 > [ 19.783695] type=1505 audit(1245307883.751:6): > operation="profile_load" > name="/usr/lib/connman/scripts/dhclient-script" name2="default" > pid=1952 > [ 19.980398] type=1505 audit(1245307883.951:7): > operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" > name2="default" pid=1957 > [ 19.981096] type=1505 audit(1245307883.951:8): > operation="profile_load" name="/usr/sbin/cupsd" name2="default" > pid=1957 > [ 20.021125] type=1505 audit(1245307883.991:9): > operation="profile_load" name="/usr/sbin/tcpdump" name2="default" > pid=1961 > [ 20.873146] input: PS/2 Generic Mouse as > /devices/platform/i8042/serio4/serio5/input/input8 > [ 22.375044] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 > [ 22.375050] Bluetooth: BNEP filters: protocol multicast > [ 22.401539] Bridge firewalling registered > [ 23.842402] pci 0000:01:05.0: PCI INT A -> Link[C0C4] -> GSI 10 > (level, low) -> IRQ 10 > [ 24.582768] [drm] Initialized drm 1.1.0 20060810 > [ 24.693750] [drm] Initialized radeon 1.29.0 20080528 on minor 0 > [ 25.190733] agpgart-ati 0000:00:00.0: AGP 2.0 bridge > [ 25.190769] agpgart-ati 0000:00:00.0: putting AGP V2 device into 4x mode > [ 25.190827] pci 0000:01:05.0: putting AGP V2 device into 4x mode > [ 25.390898] [drm] Setting GART location based on new memory map > [ 25.390912] [drm] Loading R100 Microcode > [ 25.390963] [drm] writeback test succeeded in 1 usecs > [ 28.331207] ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 28.336321] ADDRCONF(NETDEV_UP): eth1: link is not ready > [ 28.340329] eth1: New link status: Disconnected (0002) > [ 1488.782117] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 1488.782128] tg3: eth0: Flow control is on for TX and on for RX. > [ 1488.782277] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 1498.868289] eth0: no IPv6 routers present > [ 1610.733496] tg3: eth0: Link is down. > [ 1612.456228] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 1612.456239] tg3: eth0: Flow control is on for TX and on for RX. > [ 1631.644110] tg3: eth0: Link is down. > [ 1633.288603] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 1633.288614] tg3: eth0: Flow control is on for TX and on for RX. > [ 1934.765135] tg3: eth0: Link is down. > [ 1936.487217] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 1936.487225] tg3: eth0: Flow control is on for TX and on for RX. > [ 1947.270751] tg3: eth0: Link is down. > [ 1948.951325] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 1948.951337] tg3: eth0: Flow control is on for TX and on for RX. > [ 1948.964254] tg3: eth0: Link is down. > [ 1950.602717] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 1950.602728] tg3: eth0: Flow control is on for TX and on for RX. > [ 2130.277627] tg3: eth0: Link is down. > [ 2131.894865] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 2131.894873] tg3: eth0: Flow control is on for TX and on for RX. > [ 3246.864560] ppdev0: registered pardevice > [ 3246.955610] ppdev0: unregistered pardevice > [ 3247.088270] ppdev0: registered pardevice > [ 3247.136173] ppdev0: unregistered pardevice > [ 3247.925247] ppdev0: registered pardevice > [ 3247.972254] ppdev0: unregistered pardevice > [ 6578.509255] tg3: eth0: Link is down. > [ 6580.175833] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 6580.175841] tg3: eth0: Flow control is on for TX and on for RX. > > Module Size Used by > binfmt_misc 16776 1 > radeon 342816 2 > drm 96296 3 radeon > bridge 56340 0 > stp 10500 1 bridge > bnep 20224 2 > input_polldev 11912 0 > lp 17156 0 > orinoco_cs 21004 1 > joydev 18368 0 > orinoco 61716 1 orinoco_cs > hermes_dld 15232 1 orinoco > hermes 15360 3 orinoco_cs,orinoco,hermes_dld > pcmcia 44748 1 orinoco_cs > snd_ali5451 27276 3 > snd_ac97_codec 112292 1 snd_ali5451 > ac97_bus 9856 1 snd_ac97_codec > snd_pcm_oss 46336 0 > snd_mixer_oss 22656 1 snd_pcm_oss > snd_pcm 82948 3 snd_ali5451,snd_ac97_codec,snd_pcm_oss > snd_seq_dummy 10756 0 > snd_seq_oss 37760 0 > snd_seq_midi 14336 0 > snd_rawmidi 29696 1 snd_seq_midi > snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi > snd_seq 56880 6 > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event > snd_timer 29704 2 snd_pcm,snd_seq > snd_seq_device 14988 5 > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq > snd 62628 16 > snd_ali5451,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device > i2c_ali15x3 14724 0 > psmouse 61972 0 > soundcore 15200 1 snd > ati_agp 14988 1 > ppdev 15620 0 > video 25360 0 > parport_pc 40100 1 > parport 42220 3 lp,ppdev,parport_pc > pcspkr 10496 0 > serio_raw 13316 0 > snd_page_alloc 16904 1 snd_pcm > shpchp 40212 0 > i2c_ali1535 14212 0 > agpgart 42696 2 drm,ati_agp > output 11008 1 video > yenta_socket 32396 5 > rsrc_nonstatic 19328 1 yenta_socket > pcmcia_core 43540 4 > orinoco_cs,pcmcia,yenta_socket,rsrc_nonstatic > tg3 131204 0 > fbcon 46112 0 > tileblit 10752 1 fbcon > font 16384 1 fbcon > bitblit 13824 1 fbcon > softcursor 9984 1 bitblit >