You need your username and password, plus the phone number. your wvdial.conf should look like: root@slax:~# cat /etc/wvdial.conf [Dialer Defaults] Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Modem Type = Analog Modem Phone = 1234567??? ISDN = 0 Username = your_username??? Init1 = ATZ Password = your_password?? Modem = /dev/ttySM0 Baud = 460800 Carrier Check = no Stupid Mode = 1 <--- this is optional If you have already a username, password and phone number, please read Jacques post-install.html from http://linmodems.technion.ac.il/post-install.html If all is setup properly, then send us output of # tail -f /var/log/messages or $ sudo tail -f /var/log/messages Also it would help a bit, might even more if you send us ModemData.txt to confirm that the driver is the one that you need. There is a newer martian-full-20080625.tar.gz available that might be even better than the one that you have if your kernel is >= 2.6.24/25 . Regards, Antonio On 9/14/08, Alexey Putilov <alputilov@xxxxxxx> wrote: > Hello! > I am Alexey from Rusia, I have Agere lucent Win modem > I have downloaded the recommended by Scanmodem driver > martian-full-20071011.tar.gz. > Then I`ve installed it as it was recomended in the file INSTALL: > make all > make install > > modprobe martian_dev > martian_modem /dev/ttyLT0 > Using KInternet I ring to provider, modem works write but a connection > doesn1t establish. > The write login is mts, password mts, number 88007072850 > KInternet says: > > SuSE Meta pppd (smpppd-ifcfg), Version 1.59 on host0. > Status is: disconnected > trying to connect to smpppd > connect to smpppd > Status is: disconnected > Status is: connecting > pppd[0]: Plugin passwordfd.so loaded. > pppd[0]: --> WvDial: Internet dialer version 1.54.0 > pppd[0]: --> Initializing modem. > pppd[0]: --> Sending: ATM1 > pppd[0]: ATM1 > pppd[0]: OK > pppd[0]: --> Sending: ATX3 > pppd[0]: ATX3 > pppd[0]: OK > pppd[0]: --> Modem initialized. > pppd[0]: --> Sending: ATDP8,,8007072850 > pppd[0]: --> Waiting for carrier. > pppd[0]: ATDP8,,8007072850 > pppd[0]: CONNECT 48000 V42bis > pppd[0]: User Access Verification > pppd[0]: Username: > pppd[0]: --> Carrier detected. Waiting for prompt. > pppd[0]: User Access Verification > pppd[0]: Username: > pppd[0]: --> Looks like a login prompt. > pppd[0]: --> Sending: mts > pppd[0]: mts > pppd[0]: Password: > pppd[0]: --> Looks like a password prompt. > pppd[0]: --> Sending: (password) > pppd[0]: % Authentication failed. > pppd[0]: User Access Verification > pppd[0]: Username: > pppd[0]: --> Looks like a login prompt. > pppd[0]: --> Sending: mts > pppd[0]: mts > pppd[0]: Password: > pppd[0]: --> Looks like a password prompt. > pppd[0]: --> Sending: (password) > pppd[0]: % Authentication failed. > pppd[0]: --> Don't know what to do! Starting pppd and hoping for the best. > pppd[0]: Serial connection established. > pppd[0]: Renamed interface ppp0 to modem0 > pppd[0]: Using interface modem0 > Status is: connecting > pppd[0]: Connect: modem0 <--> /dev/ttyLT0 > pppd[0]: Modem hangup > pppd[0]: Connection terminated. > Status is: disconnected > pppd[0] died: A modem hung up the phone (exit code 16) > > The INSTALL recommends: For wvdial add "Check Carrier = No" line, I added in > some places > Listing of wvdial.conf: > > [Dialer Defaults] > Check Carrier = No > Modem = /dev/modem > Check Carrier = No > Baud = 57600 > Check Carrier = No > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 > Init3 = > Check Carrier = No > Area Code = > Phone = 0 > Username = > Password = > Ask Password = 0 > Dial Command = ATDT > Stupid Mode = 1 > Compuserve = 0 > Force Address = > Idle Seconds = 300 > DialMessage1 = > DialMessage2 = > ISDN = 0 > Auto DNS = 1 > Check Carrier = No > > I now don`t know what to do > > THANK YOU VERY MUCH FOR ANY HELP! > >
