Hello, It looks like the ALSA symbols didn't get exported correctly. Please look at this HOWTO and follow steps 2 and three: http://linmodems.technion.ac.il/packages/ltmodem/11c11040/HOWTO-Agere-11c11040-HDA.html Bjorn. --- Graeme Nichols <gnichols@xxxxxxxxxx> wrote: > Bjorn Wielens wrote: > > Hi Graeme, > > After doing the insmod, can you send me the output > of > > 'dmesg | tail'? this will help us figure out what > went > > wrong. > > Bjorn. > > Hi Bjorn, Marvin, > > OK. Done. > > Thank you. > > Regards, > > Graeme. > > > > > > > > > --- Graeme Nichols <gnichols@xxxxxxxxxx> wrote: > > > >> Bjorn Wielens wrote: > >>> Hi Graeme, > >>> This issue has been brought to our attention, > and > >> can > >>> be resolved by copying the serial26.c file from > >> the > >>> agrsm-HDA-20080721.tar.bz2 file over the > >> serial26.c > >>> file in the agrsm-HDA-20080721-ALSA15 folder > >> you're > >>> currently working from. > >>> > >>> Cheers, > >>> Bjorn. > >> Hi Bjorn, Marvin, > >> > >> Some progress. I copied over the file as you > suggest > >> above. > >> > >> make module completes without error. > >> > >> make install fails. > >> > >> insmod also fails. > >> > >> I have attached the output of both commands. > >> > >> This may be fairly simple to overcome now (he > says > >> keeping his fingers > >> crossed) > >> > >> Regards, > >> > >> Graeme. > > > No virus found in this outgoing message. > Checked by AVG - http://www.avg.com > Version: 8.0.138 / Virus Database: 270.5.7/1580 - > Release Date: 29/07/2008 5:26 PM > > > Bluetooth: L2CAP ver 2.9 > Bluetooth: L2CAP socket layer initialized > Bluetooth: RFCOMM socket layer initialized > Bluetooth: RFCOMM TTY layer initialized > Bluetooth: RFCOMM ver 1.8 > warning: process `hwsetup' used the deprecated > sysctl system call with 1.23. > warning: process `hwsetup' used the deprecated > sysctl system call with 1.49. > warning: process `hwsetup' used the deprecated > sysctl system call with 1.49. > device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) > initialised: dm-devel@xxxxxxxxxx > loop: AES key scrubbing enabled > loop: loaded (max 8 devices) > aufs clean_plink:361:mount[4022]: failed rmdir > .wh..wh.plink (-39), ignored. > r8169: eth0: link down > NET: Registered protocol family 10 > lo: Disabled Privacy Extensions > ADDRCONF(NETDEV_UP): eth0: link is not ready > ogg123[4425]: segfault at b766e020 eip b7eeda4f esp > bfa27544 error 4 > agrmodem: module license 'Proprietary' taints > kernel. > agrmodem: Unknown symbol snd_hda_codec_read > agrmodem: Unknown symbol snd_hda_codec_write > agrserial: Unknown symbol uart_get_baud_rate > agrserial: Unknown symbol uart_resume_port > agrserial: Unknown symbol uart_register_driver > agrserial: Unknown symbol uart_suspend_port > agrserial: Unknown symbol uart_remove_one_port > agrserial: Unknown symbol uart_update_timeout > agrserial: Unknown symbol uart_unregister_driver > agrserial: Unknown symbol uart_get_divisor > agrserial: Unknown symbol uart_add_one_port > agrserial: Unknown symbol uart_write_wakeup > __________________________________________________________________ Get a sneak peak at messages with a handy reading pane with All new Yahoo! Mail: http://ca.promos.yahoo.com/newmail/overview2/
