Stuart, The object of this step is to specify functions which should NOT be activated on bootup, as they may compete for needed modem resources. Once the modem is functional, you can try adding them back one by one. Create a file with: $ sudo gedit /etc/modprobe.d/kay with lines below. You don't have to include the lines beginning with # # are comment lines and not read by the System , blacklist shpchp # PCI hotplug devices support # blackisted modules will not be loaded upon bootup, usually. To check # lsmod | grep shpchp blacklist e1000 # for your Intel ethernet e1000, to check # lsmod | grep e1000 # could be loaded later with # sudo modprobe e1000 blacklist ath_hal # Atheros wireless driver blacklist pcmcia # pcmcia functions blacklist parport_pc blacklist ppdev # parallel printer port stuff backlist l2cap blacklist rfcomm # bluetooth support blacklist usbcore # usb port support, physically remove non essential functions too ## END Save the file and reboot, it will then be read. Rerun scanModem and check for modem detection by ALSA diagnostics. MarvS On Sat, May 10, 2008 at 2:07 PM, Stuart Kay <horndog_ut2k3@xxxxxxxxx> wrote: > Marvin, > Here is the info you requested: > > $ cat /proc/asound/pcm > 00-04: Intel ICH - IEC958 : Intel 82801DB-ICH4 - > IEC958 : playback 1 > 00-03: Intel ICH - ADC2 : Intel 82801DB-ICH4 - ADC2 : > capture 1 > 00-02: Intel ICH - MIC2 ADC : Intel 82801DB-ICH4 - > MIC2 ADC : capture 1 > 00-01: Intel ICH - MIC ADC : Intel 82801DB-ICH4 - MIC > ADC : capture 1 > 00-00: Intel ICH : Intel 82801DB-ICH4 : playback 1 : > capture 1 > > > $ dmesg | grep 00:1f.6 > [ 19.471416] ACPI: PCI Interrupt 0000:00:1f.6[B] -> > Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 > [ 19.471427] ACPI: PCI interrupt for device > 0000:00:1f.6 disabled > > Thanks for the help. > Stuart Kay > --- Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> > wrote: > >> Stuart, >> The modem in 00:1f.6 slot >> Class 0703: 8086:24c6 Modem: Intel Corporation >> 82801DB/DBL/DBM >> Primary device ID: 8086:24c6 >> Subsystem PCI_id 1014:0524 >> Softmodem codec or chipset from diagnostics: >> from Archives: >> SIL27, an LSI/AgereSystems >> >> is recognized from frimware readout >> as a SIL27, an LSI/AgereSystems type from archival >> data. >> >> But the ALSA tools on which its function depends >> failed to get a >> diagnostic readout. >> Within the The /proc/asound/pcm file , there should >> have been an >> additional line like >> 01-00 modem something. >> >> The problem is that the >> Modem interrupt assignment and sharing for >> Interrupt (IRQ) 11 >> 11: 98534 XT-PIC-XT uhci_hcd:usb1, >> uhci_hcd:usb2, >> uhci_hcd:usb3, ehci_hcd:usb4, yenta, yenta, wifi0, >> eth0, Intel 82801DB-ICH4, >> radeon@pci:0000:01:00.0 >> have so many devices, that the kernel couldn't >> apportion resources >> >> Consequently during >> --- Bootup diagnostics for card in PCI slot 00:1f.6 >> ---- >> [ 30.160500] ACPI: PCI Interrupt 0000:00:1f.6[B] >> -> Link [LNKB] -> GSI 11 >> (level, low) -> IRQ 11 >> [ 30.160511] ACPI: PCI interrupt for device >> 0000:00:1f.6 disabled >> and the modem cannot be functional unless >> 0000:00:1f.6 is enabled. >> >> Running a few trials with lesser loads on the >> kernel, may improve this >> situation. >> After each bootup, do >> $ cat /proc/asound/pcm >> $ dmesg | grep 00:1f.6 >> to check for the appearance of a modem line, or >> rerun scanModem for >> more details. >> Until 0000:00:1f.6 is enabled, the modem will not be >> responsive!!! >> >> Trial 1) >> Before the next boot into Linux, disconnect all the >> USB devices and >> take out any cards from the PCMCIA slot. >> >> If that doesn't help, read the Bootup.txt, but don't >> try anything else yet. Do: >> $ lspci >> sk.txt >> $ echo >> sk.txt >> $ lspci -n >> sk.txt >> $ echo >> sk.txt >> $ dmesg >> sk.txt >> and send us the sk.txt >> That will provide details from which we can specify >> reductions of >> other bootup services. >> >> MarvS >> scanModem maintainer >> >> >> On Sat, May 10, 2008 at 1:36 AM, Stuart Kay >> <horndog_ut2k3@xxxxxxxxx> wrote: >> > -------------------------- System information >> ---------------------------- >> > CPU=i686, >> > Linux version 2.6.24-16-generic (buildd@palmer) >> (gcc version 4.2.3 (Ubuntu >> > 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC >> 2008 >> > scanModem update of: 2008_05_02 >> > >> > There are no blacklisted modem drivers in >> /etc/modprobe* files >> > Attached USB devices are: >> > ID 03f0:2812 Hewlett-Packard >> > ID 04a9:1900 Canon, Inc. >> > ID 152e:2507 LG (HLDS) >> > ID 0781:5406 SanDisk Corp. Cruzer Micro 4GB Flash >> Drive >> > ID 04b3:4482 IBM Corp. >> > ID 0a5c:200a Broadcom Corp. Bluetooth dongle >> > >> > USB modems not recognized >> > For candidate card in slot 00:1f.6, firmware >> information and bootup >> > diagnostics are: >> > PCI slot PCI ID SubsystemID >> Name >> > ---------- --------- --------- >> -------------- >> > 00:1f.6 8086:24c6 1014:0524 >> Modem: Intel Corporation >> > 82801DB/DBL/DBM >> > >> > Modem interrupt assignment and sharing: >> > 11: 98534 XT-PIC-XT uhci_hcd:usb1, >> uhci_hcd:usb2, >> > uhci_hcd:usb3, ehci_hcd:usb4, yenta, yenta, wifi0, >> eth0, Intel 82801DB-ICH4, >> > radeon@pci:0000:01:00.0 >> > --- Bootup diagnostics for card in PCI slot >> 00:1f.6 ---- >> > [ 30.160500] ACPI: PCI Interrupt 0000:00:1f.6[B] >> -> Link [LNKB] -> GSI 11 >> > (level, low) -> IRQ 11 >> > [ 30.160511] ACPI: PCI interrupt for device >> 0000:00:1f.6 disabled >> > >> > The PCI slot 00:1f.6 of the modem card may be >> disabled early in >> > a bootup process, but then enabled later. If >> modem drivers load >> > but the modem is not responsive, read Bootup.txt >> about possible fixes. >> > Send dmesg.txt along with ModemData.txt to >> discuss@xxxxxxxxxxxxx >> > if help is needed. >> > >> > >> > >> > ===== Advanced Linux Sound Architecture (ALSA) >> diagnostics ===== >> > The ALSA packages provide audio support and also >> drivers for some modems. >> > ALSA diagnostics are written during bootup to >> /proc/asound/ folders. >> > >> > The ALSA verion is 1.0.15 >> > The modem cards detected by "aplay -l" are: >> > >> > >> > The /proc/asound/pcm file reports: >> > ----------------------- >> > 00-04: Intel ICH - IEC958 : Intel 82801DB-ICH4 - >> IEC958 : playback 1 >> > 00-03: Intel ICH - ADC2 : Intel 82801DB-ICH4 - >> ADC2 : capture 1 >> > 00-02: Intel ICH - MIC2 ADC : Intel 82801DB-ICH4 - >> MIC2 ADC : capture 1 >> > 00-01: Intel ICH - MIC ADC : Intel 82801DB-ICH4 - >> MIC ADC : capture 1 >> > 00-00: Intel ICH : Intel 82801DB-ICH4 : playback 1 >> : capture 1 >> > >> > about /proc/asound/cards: >> > ------------------------ >> > 0 [I82801DBICH4 ]: ICH4 - Intel 82801DB-ICH4 >> > Intel 82801DB-ICH4 with >> AD1981B at irq 11 >> > ===== Advanced Linux Sound Architecture (ALSA) >> diagnostics ===== >> > The ALSA packages provide audio support and also >> drivers for some modems. >> > ALSA diagnostics are written during bootup to >> /proc/asound/ folders. >> > >> > The ALSA verion is 1.0.15 >> > The modem cards detected by "aplay -l" are: >> > >> > >> > The /proc/asound/pcm file reports: >> > ----------------------- >> > 00-04: Intel ICH - IEC958 : Intel 82801DB-ICH4 - >> IEC958 : playback 1 >> > 00-03: Intel ICH - ADC2 : Intel 82801DB-ICH4 - >> ADC2 : capture 1 >> > 00-02: Intel ICH - MIC2 ADC : Intel 82801DB-ICH4 - >> MIC2 ADC : capture 1 >> > 00-01: Intel ICH - MIC ADC : Intel 82801DB-ICH4 - >> MIC ADC : capture 1 >> > 00-00: Intel ICH : Intel 82801DB-ICH4 : playback 1 >> : capture 1 >> > >> > about /proc/asound/cards: >> > ------------------------ >> > 0 [I82801DBICH4 ]: ICH4 - Intel 82801DB-ICH4 >> > Intel 82801DB-ICH4 with >> AD1981B at irq 11 >> > === Finished firmware and bootup diagnostics, next >> deducing cogent software. >> > === >> > >> > Predictive diagnostics for card in bus 00:1f.6: >> > Modem chipset detected on >> > === message truncated === > > 00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03) > 00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03) > 00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) > 00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) > 00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) > 00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) > 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81) > 00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01) > 00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01) > 00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01) > 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01) > 00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01) > 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] > 02:00.0 CardBus bridge: Texas Instruments PCI4520 PC card Cardbus Controller (rev 01) > 02:00.1 CardBus bridge: Texas Instruments PCI4520 PC card Cardbus Controller (rev 01) > 02:01.0 Ethernet controller: Intel Corporation 82540EP Gigabit Ethernet Controller (Mobile) (rev 03) > 02:02.0 Ethernet controller: Atheros Communications Inc. AR5212 802.11abg NIC (rev 01) > > 00:00.0 0600: 8086:3340 (rev 03) > 00:01.0 0604: 8086:3341 (rev 03) > 00:1d.0 0c03: 8086:24c2 (rev 01) > 00:1d.1 0c03: 8086:24c4 (rev 01) > 00:1d.2 0c03: 8086:24c7 (rev 01) > 00:1d.7 0c03: 8086:24cd (rev 01) > 00:1e.0 0604: 8086:2448 (rev 81) > 00:1f.0 0601: 8086:24cc (rev 01) > 00:1f.1 0101: 8086:24ca (rev 01) > 00:1f.3 0c05: 8086:24c3 (rev 01) > 00:1f.5 0401: 8086:24c5 (rev 01) > 00:1f.6 0703: 8086:24c6 (rev 01) > 01:00.0 0300: 1002:4c57 > 02:00.0 0607: 104c:ac46 (rev 01) > 02:00.1 0607: 104c:ac46 (rev 01) > 02:01.0 0200: 8086:101e (rev 03) > 02:02.0 0200: 168c:1014 (rev 01) > > [ 0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic) > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable) > [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved) > [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff60000 (usable) > [ 0.000000] BIOS-e820: 000000007ff60000 - 000000007ff77000 (ACPI data) > [ 0.000000] BIOS-e820: 000000007ff77000 - 000000007ff79000 (ACPI NVS) > [ 0.000000] BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved) > [ 0.000000] BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved) > [ 0.000000] 1151MB HIGHMEM available. > [ 0.000000] 896MB LOWMEM available. > [ 0.000000] Entering add_active_range(0, 0, 524128) 0 entries of 256 used > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] Normal 4096 -> 229376 > [ 0.000000] HighMem 229376 -> 524128 > [ 0.000000] Movable zone start PFN for each node > [ 0.000000] early_node_map[1] active PFN ranges > [ 0.000000] 0: 0 -> 524128 > [ 0.000000] On node 0 totalpages: 524128 > [ 0.000000] DMA zone: 32 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > [ 0.000000] Normal zone: 1760 pages used for memmap > [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 > [ 0.000000] HighMem zone: 2302 pages used for memmap > [ 0.000000] HighMem zone: 292450 pages, LIFO batch:31 > [ 0.000000] Movable zone: 0 pages used for memmap > [ 0.000000] DMI present. > [ 0.000000] ACPI: RSDP signature @ 0xC00F6D70 checksum 0 > [ 0.000000] ACPI: RSDP 000F6D70, 0024 (r2 IBM ) > [ 0.000000] ACPI: XSDT 7FF6A672, 004C (r1 IBM TP-1R 3230 LTP 0) > [ 0.000000] ACPI: FACP 7FF6A700, 00F4 (r3 IBM TP-1R 3230 IBM 1) > [ 0.000000] ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20070126] > [ 0.000000] ACPI: DSDT 7FF6A8E7, C530 (r1 IBM TP-1R 3230 MSFT 100000E) > [ 0.000000] ACPI: FACS 7FF78000, 0040 > [ 0.000000] ACPI: SSDT 7FF6A8B4, 0033 (r1 IBM TP-1R 3230 MSFT 100000E) > [ 0.000000] ACPI: ECDT 7FF76E17, 0052 (r1 IBM TP-1R 3230 IBM 1) > [ 0.000000] ACPI: TCPA 7FF76E69, 0032 (r1 IBM TP-1R 3230 PTL 1) > [ 0.000000] ACPI: BOOT 7FF76FD8, 0028 (r1 IBM TP-1R 3230 LTP 1) > [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 > [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7f800000) > [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 > [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000 > [ 0.000000] swsusp: Registered nosave memory region: 00000000000d2000 - 00000000000d4000 > [ 0.000000] swsusp: Registered nosave memory region: 00000000000d4000 - 00000000000dc000 > [ 0.000000] swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520034 > [ 0.000000] Kernel command line: root=UUID=24903F58903F3022 loop=/ubuntu/disks/root.disk ro quiet splash > [ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic" > [ 0.000000] mapped APIC to ffffb000 (02014000) > [ 0.000000] Enabling fast FPU save and restore... done. > [ 0.000000] Enabling unmasked SIMD FPU exception support... done. > [ 0.000000] Initializing CPU#0 > [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) > [ 0.000000] Detected 1594.893 MHz processor. > [ 17.470244] Console: colour VGA+ 80x25 > [ 17.470249] console [tty0] enabled > [ 17.470857] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) > [ 17.471514] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > [ 17.597830] Memory: 2066344k/2096512k available (2157k kernel code, 29024k reserved, 998k data, 364k init, 1179008k highmem) > [ 17.597840] virtual kernel memory layout: > [ 17.597841] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB) > [ 17.597842] pkmap : 0xff800000 - 0xffc00000 (4096 kB) > [ 17.597844] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) > [ 17.597845] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) > [ 17.597846] .init : 0xc041b000 - 0xc0476000 ( 364 kB) > [ 17.597848] .data : 0xc031b5a4 - 0xc0414dc4 ( 998 kB) > [ 17.597849] .text : 0xc0100000 - 0xc031b5a4 (2157 kB) > [ 17.597853] Checking if this processor honours the WP bit even in supervisor mode... Ok. > [ 17.597917] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 > [ 17.677936] Calibrating delay using timer specific routine.. 3192.15 BogoMIPS (lpj=6384302) > [ 17.677979] Security Framework initialized > [ 17.677991] SELinux: Disabled at boot. > [ 17.678013] AppArmor: AppArmor initialized > [ 17.678018] Failure registering capabilities with primary security module. > [ 17.678029] Mount-cache hash table entries: 512 > [ 17.678214] CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 00000000 > [ 17.678231] CPU: L1 I cache: 32K, L1 D cache: 32K > [ 17.678234] CPU: L2 cache: 1024K > [ 17.678238] CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00002040 00000180 00000000 00000000 00000000 > [ 17.678250] Compat vDSO mapped to ffffe000. > [ 17.678268] Checking 'hlt' instruction... OK. > [ 17.694365] SMP alternatives: switching to UP code > [ 17.696468] Freeing SMP alternatives: 11k freed > [ 17.696608] Early unpacking initramfs... done > [ 18.112755] ACPI: Core revision 20070126 > [ 18.112880] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. > [ 18.117567] ACPI: setting ELCR to 0200 (from 0800) > [ 18.127743] CPU0: Intel(R) Pentium(R) M processor 1600MHz stepping 05 > [ 18.127749] SMP motherboard not detected. > [ 18.127752] Local APIC not detected. Using dummy APIC emulation. > [ 18.127798] Brought up 1 CPUs > [ 18.127819] CPU0 attaching sched-domain: > [ 18.127822] domain 0: span 01 > [ 18.127824] groups: 01 > [ 18.128016] net_namespace: 64 bytes > [ 18.128024] Booting paravirtualized kernel on bare hardware > [ 18.128677] Time: 12:26:17 Date: 05/10/08 > [ 18.128706] NET: Registered protocol family 16 > [ 18.128911] EISA bus registered > [ 18.128923] ACPI: bus type pci registered > [ 18.129227] PCI: PCI BIOS revision 2.10 entry at 0xfd8d6, last bus=8 > [ 18.129230] PCI: Using configuration type 1 > [ 18.129232] Setting up standard PCI resources > [ 18.133771] ACPI: EC: EC description table is found, configuring boot EC > [ 18.139492] ACPI: EC: non-query interrupt received, switching to interrupt mode > [ 18.142627] ACPI: Interpreter enabled > [ 18.142630] ACPI: (supports S0 S3 S4 S5) > [ 18.142645] ACPI: Using PIC for interrupt routing > [ 18.149514] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62 > [ 18.149517] ACPI: EC: driver started in poll mode > [ 18.149666] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 18.150082] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO > [ 18.150086] PCI quirk: region 1180-11bf claimed by ICH4 GPIO > [ 18.150620] PCI: Transparent bridge - 0000:00:1e.0 > [ 18.150723] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 18.150782] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] > [ 18.150808] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] > [ 18.154596] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11) > [ 18.154793] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11) > [ 18.154986] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11) > [ 18.155179] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11) > [ 18.155356] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. > [ 18.155534] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. > [ 18.155711] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. > [ 18.155905] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11) > [ 18.156073] ACPI: EC: non-query interrupt received, switching to interrupt mode > [ 18.156164] ACPI: Power Resource [PUBS] (on) > [ 18.156210] Linux Plug and Play Support v0.97 (c) Adam Belay > [ 18.156242] pnp: PnP ACPI init > [ 18.156250] ACPI: bus type pnp registered > [ 18.157352] pnpacpi: exceeded the max number of mem resources: 12 > [ 18.159828] pnp: PnP ACPI: found 13 devices > [ 18.159831] ACPI: ACPI bus type pnp unregistered > [ 18.159835] PnPBIOS: Disabled by ACPI PNP > [ 18.160070] PCI: Using ACPI for IRQ routing > [ 18.160073] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report > [ 18.177937] NET: Registered protocol family 8 > [ 18.177940] NET: Registered protocol family 20 > [ 18.178008] AppArmor: AppArmor Filesystem Enabled > [ 18.181904] Time: tsc clocksource has been installed. > [ 18.189941] system 00:00: iomem range 0x0-0x9ffff could not be reserved > [ 18.189945] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved > [ 18.189948] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved > [ 18.189951] system 00:00: iomem range 0xc8000-0xcbfff could not be reserved > [ 18.189955] system 00:00: iomem range 0xcc000-0xcffff could not be reserved > [ 18.189958] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved > [ 18.189961] system 00:00: iomem range 0x0-0x0 could not be reserved > [ 18.189964] system 00:00: iomem range 0x0-0x0 could not be reserved > [ 18.189967] system 00:00: iomem range 0xdc000-0xdffff has been reserved > [ 18.189970] system 00:00: iomem range 0xe0000-0xe3fff could not be reserved > [ 18.189974] system 00:00: iomem range 0xe4000-0xe7fff could not be reserved > [ 18.189977] system 00:00: iomem range 0xe8000-0xebfff could not be reserved > [ 18.189984] system 00:02: ioport range 0x1000-0x107f has been reserved > [ 18.189987] system 00:02: ioport range 0x1180-0x11bf has been reserved > [ 18.189990] system 00:02: ioport range 0x15e0-0x15ef has been reserved > [ 18.189993] system 00:02: ioport range 0x1600-0x162f has been reserved > [ 18.189996] system 00:02: ioport range 0x1632-0x167f has been reserved > [ 18.189999] system 00:02: ioport range 0x1630-0x1631 has been reserved > [ 18.220430] PCI: Bridge: 0000:00:01.0 > [ 18.220433] IO window: 3000-3fff > [ 18.220437] MEM window: c0100000-c01fffff > [ 18.220440] PREFETCH window: e0000000-e7ffffff > [ 18.220448] PCI: Bus 3, cardbus bridge: 0000:02:00.0 > [ 18.220450] IO window: 00004000-000040ff > [ 18.220454] IO window: 00004400-000044ff > [ 18.220458] PREFETCH window: e8000000-ebffffff > [ 18.220462] MEM window: c4000000-c7ffffff > [ 18.220467] PCI: Bus 7, cardbus bridge: 0000:02:00.1 > [ 18.220469] IO window: 00004800-000048ff > [ 18.220472] IO window: 00004c00-00004cff > [ 18.220477] PREFETCH window: ec000000-efffffff > [ 18.220481] MEM window: c8000000-cbffffff > [ 18.220484] PCI: Bridge: 0000:00:1e.0 > [ 18.220487] IO window: 4000-8fff > [ 18.220492] MEM window: c0200000-cfffffff > [ 18.220496] PREFETCH window: e8000000-efffffff > [ 18.220511] PCI: Setting latency timer of device 0000:00:1e.0 to 64 > [ 18.220876] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 > [ 18.220879] PCI: setting IRQ 11 as level-triggered > [ 18.220883] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 > [ 18.221225] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 > [ 18.221228] ACPI: PCI Interrupt 0000:02:00.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 > [ 18.221244] NET: Registered protocol family 2 > [ 18.257983] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) > [ 18.258292] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) > [ 18.259694] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) > [ 18.260670] TCP: Hash tables configured (established 131072 bind 65536) > [ 18.260674] TCP reno registered > [ 18.270109] checking if image is initramfs... it is > [ 18.721889] Switched to high resolution mode on CPU 0 > [ 19.079333] Freeing initrd memory: 7705k freed > [ 19.079577] Simple Boot Flag at 0x35 set to 0x1 > [ 19.079948] audit: initializing netlink socket (disabled) > [ 19.079967] audit(1210422377.476:1): initialized > [ 19.080195] highmem bounce pool size: 64 pages > [ 19.082436] VFS: Disk quotas dquot_6.5.1 > [ 19.082529] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 19.082699] io scheduler noop registered > [ 19.082702] io scheduler anticipatory registered > [ 19.082705] io scheduler deadline registered > [ 19.082721] io scheduler cfq registered (default) > [ 19.082795] Boot video device is 0000:01:00.0 > [ 19.083122] isapnp: Scanning for PnP cards... > [ 19.436225] isapnp: No Plug & Play device found > [ 19.469582] Real Time Clock Driver v1.12ac > [ 19.469701] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > [ 19.470976] serial 00:0a: activated > [ 19.471231] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A > [ 19.471416] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 > [ 19.471427] ACPI: PCI interrupt for device 0000:00:1f.6 disabled > [ 19.472067] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize > [ 19.472150] input: Macintosh mouse button emulation as /devices/virtual/input/input0 > [ 19.472259] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 > [ 19.479796] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 19.479801] serio: i8042 AUX port at 0x60,0x64 irq 12 > [ 19.481836] mice: PS/2 mouse device common for all mice > [ 19.481952] EISA: Probing bus 0 at eisa.0 > [ 19.481958] Cannot allocate resource for EISA slot 1 > [ 19.481962] Cannot allocate resource for EISA slot 2 > [ 19.481964] Cannot allocate resource for EISA slot 3 > [ 19.481967] Cannot allocate resource for EISA slot 4 > [ 19.481969] Cannot allocate resource for EISA slot 5 > [ 19.481971] Cannot allocate resource for EISA slot 6 > [ 19.481973] Cannot allocate resource for EISA slot 7 > [ 19.481976] Cannot allocate resource for EISA slot 8 > [ 19.481978] EISA: Detected 0 cards. > [ 19.481981] cpuidle: using governor ladder > [ 19.481983] cpuidle: using governor menu > [ 19.482093] NET: Registered protocol family 1 > [ 19.482124] Using IPI No-Shortcut mode > [ 19.482159] registered taskstats version 1 > [ 19.482276] Magic number: 8:390:430 > [ 19.482418] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found > [ 19.482420] EDD information not available. > [ 19.482657] Freeing unused kernel memory: 364k freed > [ 19.486147] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 > [ 20.706610] fuse init (API version 7.9) > [ 20.732264] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > [ 20.732271] ACPI: Processor [CPU] (supports 8 throttling states) > [ 20.734951] ACPI: Thermal Zone [THM0] (56 C) > [ 21.436486] usbcore: registered new interface driver usbfs > [ 21.436513] usbcore: registered new interface driver hub > [ 21.445526] usbcore: registered new device driver usb > [ 21.462571] USB Universal Host Controller Interface driver v3.0 > [ 21.462646] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 > [ 21.462660] PCI: Setting latency timer of device 0000:00:1d.0 to 64 > [ 21.462665] uhci_hcd 0000:00:1d.0: UHCI Host Controller > [ 21.463089] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 > [ 21.463115] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800 > [ 21.463278] usb usb1: configuration #1 chosen from 1 choice > [ 21.463305] hub 1-0:1.0: USB hub found > [ 21.463311] hub 1-0:1.0: 2 ports detected > [ 21.566009] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 > [ 21.566015] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 > [ 21.566027] PCI: Setting latency timer of device 0000:00:1d.1 to 64 > [ 21.566031] uhci_hcd 0000:00:1d.1: UHCI Host Controller > [ 21.566060] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 > [ 21.566083] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820 > [ 21.566212] usb usb2: configuration #1 chosen from 1 choice > [ 21.566239] hub 2-0:1.0: USB hub found > [ 21.566245] hub 2-0:1.0: 2 ports detected > [ 21.589721] SCSI subsystem initialized > [ 21.665496] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI > [ 21.665501] Copyright (c) 1999-2006 Intel Corporation. > [ 21.670011] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 > [ 21.670016] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 > [ 21.670028] PCI: Setting latency timer of device 0000:00:1d.2 to 64 > [ 21.670033] uhci_hcd 0000:00:1d.2: UHCI Host Controller > [ 21.670061] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 > [ 21.670085] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840 > [ 21.670223] usb usb3: configuration #1 chosen from 1 choice > [ 21.670251] hub 3-0:1.0: USB hub found > [ 21.670257] hub 3-0:1.0: 2 ports detected > [ 21.689455] libata version 3.00 loaded. > [ 21.774843] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 > [ 21.774848] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 > [ 21.774863] PCI: Setting latency timer of device 0000:00:1d.7 to 64 > [ 21.774868] ehci_hcd 0000:00:1d.7: EHCI Host Controller > [ 21.774900] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 > [ 21.778804] ehci_hcd 0000:00:1d.7: debug port 1 > [ 21.778811] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 > [ 21.778819] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000 > [ 21.809446] usb 1-1: new full speed USB device using uhci_hcd and address 2 > [ 21.818318] Floppy drive(s): fd0 is 1.44M > [ 21.822526] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > [ 21.822666] usb usb4: configuration #1 chosen from 1 choice > [ 21.822695] hub 4-0:1.0: USB hub found > [ 21.822703] hub 4-0:1.0: 6 ports detected > [ 21.836477] FDC 0 is a National Semiconductor PC87306 > [ 21.925656] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 > [ 22.180215] e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:11:25:44:13:aa > [ 22.218539] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection > [ 22.226665] ata_piix 0000:00:1f.1: version 2.12 > [ 22.226682] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) > [ 22.226692] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 > [ 22.226735] PCI: Setting latency timer of device 0000:00:1f.1 to 64 > [ 22.227334] scsi0 : ata_piix > [ 22.227872] scsi1 : ata_piix > [ 22.228856] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1860 irq 14 > [ 22.228860] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15 > [ 22.385391] usb 4-1: new high speed USB device using ehci_hcd and address 2 > [ 22.389845] ata1.00: ATA-6: ST9100824A, 3.04, max UDMA/100 > [ 22.389849] ata1.00: 195371568 sectors, multi 16: LBA48 > [ 22.405769] ata1.00: configured for UDMA/100 > [ 22.517895] usb 4-1: configuration #1 chosen from 1 choice > [ 22.518055] hub 4-1:1.0: USB hub found > [ 22.518154] hub 4-1:1.0: 4 ports detected > [ 22.726276] ata2.00: ATAPI: HL-DT-STDVD-ROM GDR8083N, 0K04, max UDMA/33 > [ 22.897703] ata2.00: configured for UDMA/33 > [ 22.897835] scsi 0:0:0:0: Direct-Access ATA ST9100824A 3.04 PQ: 0 ANSI: 5 > [ 22.905129] scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-ROM GDR8083N 0K04 PQ: 0 ANSI: 5 > [ 22.922958] Driver 'sd' needs updating - please use bus_type methods > [ 22.923054] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) > [ 22.923068] sd 0:0:0:0: [sda] Write Protect is off > [ 22.923071] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 22.923088] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 22.923140] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) > [ 22.923150] sd 0:0:0:0: [sda] Write Protect is off > [ 22.923152] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 22.923168] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 22.923172] sda:<4>Driver 'sr' needs updating - please use bus_type methods > [ 22.931586] sda1 > [ 22.931648] sd 0:0:0:0: [sda] Attached SCSI disk > [ 22.938748] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 22.938771] sr 1:0:0:0: Attached scsi generic sg1 type 5 > [ 22.957483] sr0: scsi3-mmc drive: 10x/24x cd/rw xa/form2 cdda tray > [ 22.957489] Uniform CD-ROM driver Revision: 3.20 > [ 22.957546] sr 1:0:0:0: Attached scsi CD-ROM sr0 > [ 23.540358] loop: module loaded > [ 23.582386] kjournald starting. Commit interval 5 seconds > [ 23.582402] EXT3-fs: mounted filesystem with ordered data mode. > [ 32.216040] Clocksource tsc unstable (delta = -109662530 ns) > [ 32.220029] Time: acpi_pm clocksource has been installed. > [ 33.164136] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 33.243920] Linux agpgart interface v0.102 > [ 33.304692] agpgart: Detected an Intel 855PM Chipset. > [ 33.384035] agpgart: AGP aperture is 256M @ 0xd0000000 > [ 33.384085] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > [ 33.532051] iTCO_vendor_support: vendor-support=0 > [ 33.588035] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) > [ 33.589202] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060) > [ 33.589254] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) > [ 33.719993] intel_rng: FWH not detected > [ 33.794357] input: Power Button (FF) as /devices/virtual/input/input2 > [ 33.811176] ACPI: Power Button (FF) [PWRF] > [ 33.811282] input: Lid Switch as /devices/virtual/input/input3 > [ 33.815869] ACPI: Lid Switch [LID] > [ 33.815970] input: Sleep Button (CM) as /devices/virtual/input/input4 > [ 33.831964] ACPI: Sleep Button (CM) [SLPB] > [ 35.155839] Yenta: CardBus bridge found at 0000:02:00.0 [1014:0552] > [ 35.155858] Yenta: Using INTVAL to route CSC interrupts to PCI > [ 35.155860] Yenta: Routing CardBus interrupts to PCI > [ 35.155865] Yenta TI: socket 0000:02:00.0, mfunc 0x01d21b22, devctl 0x64 > [ 35.156996] ath_hal: module license 'Proprietary' taints kernel. > [ 35.199746] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > [ 35.400269] Yenta: ISA IRQ mask 0x04b8, PCI irq 11 > [ 35.400274] Socket status: 30000086 > [ 35.400280] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff > [ 35.400284] cs: IO port probe 0x4000-0x8fff: clean. > [ 35.401586] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff > [ 35.401589] pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff > [ 35.463897] Yenta: CardBus bridge found at 0000:02:00.1 [1014:0552] > [ 35.463914] Yenta: Using INTVAL to route CSC interrupts to PCI > [ 35.463916] Yenta: Routing CardBus interrupts to PCI > [ 35.463921] Yenta TI: socket 0000:02:00.1, mfunc 0x01d21b22, devctl 0x64 > [ 35.504410] wlan: 0.9.4 > [ 35.591725] ath_pci: 0.9.4 > [ 35.645173] input: PC Speaker as /devices/platform/pcspkr/input/input5 > [ 35.696194] Yenta: ISA IRQ mask 0x04b8, PCI irq 11 > [ 35.696199] Socket status: 30000086 > [ 35.696204] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff > [ 35.696207] cs: IO port probe 0x4000-0x8fff: clean. > [ 35.697509] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff > [ 35.697512] pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff > [ 35.831627] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 > [ 37.039849] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:03/LNXVIDEO:00/input/input6 > [ 37.051425] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) > [ 37.689915] Non-volatile memory driver v1.2 > [ 37.940792] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0 > [ 37.940799] serio: Synaptics pass-through port at isa0060/serio1/input0 > [ 37.984078] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7 > [ 38.018774] parport_pc 00:0b: reported by Plug and Play ACPI > [ 38.018818] parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE] > [ 38.020131] thinkpad_acpi: ThinkPad ACPI Extras v0.17 > [ 38.020134] thinkpad_acpi: http://ibm-acpi.sf.net/ > [ 38.020136] thinkpad_acpi: ThinkPad BIOS 1RETDRWW (3.23 ), EC 1RHT71WW-3.04 > [ 38.020139] thinkpad_acpi: IBM ThinkPad T41 > [ 38.023463] thinkpad_acpi: another device driver is already handling bay events > [ 38.023467] thinkpad_acpi: disabling subdriver bay > [ 38.025520] input: ThinkPad Extra Buttons as /devices/virtual/input/input8 > [ 38.036028] irda_init() > [ 38.036050] NET: Registered protocol family 23 > [ 38.068909] ACPI: AC Adapter [AC] (on-line) > [ 38.116026] nsc-ircc 00:0c: activated > [ 38.116032] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1. > [ 38.116203] nsc-ircc, chip->init > [ 38.116212] nsc-ircc, Found chip at base=0x02e > [ 38.116236] nsc-ircc, driver loaded (Dag Brattli) > [ 38.116538] IrDA: Registered device irda0 > [ 38.116541] nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500 > [ 38.172552] ACPI: Battery Slot [BAT0] (battery present) > [ 38.172609] ath_rate_sample: 1.2 (0.9.4) > [ 38.175393] wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > [ 38.175403] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > [ 38.175407] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > [ 38.175417] wifi0: H/W encryption support: WEP AES AES_CCM TKIP > [ 38.175421] wifi0: mac 5.6 phy 4.1 5 GHz radio 1.7 2 GHz radio 2.3 > [ 38.175429] wifi0: Use hw queue 1 for WME_AC_BE traffic > [ 38.175431] wifi0: Use hw queue 0 for WME_AC_BK traffic > [ 38.175433] wifi0: Use hw queue 2 for WME_AC_VI traffic > [ 38.175436] wifi0: Use hw queue 3 for WME_AC_VO traffic > [ 38.175438] wifi0: Use hw queue 8 for CAB traffic > [ 38.175440] wifi0: Use hw queue 9 for beacons > [ 38.239253] wifi0: Atheros 5212: mem=0xc0210000, irq=11 > [ 38.239468] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 > [ 38.239493] PCI: Setting latency timer of device 0000:00:1f.5 to 64 > [ 38.285686] NET: Registered protocol family 17 > [ 39.163018] intel8x0_measure_ac97_clock: measured 55453 usecs > [ 39.163023] intel8x0: clocking to 48000 > [ 39.963449] cs: IO port probe 0x100-0x3af: clean. > [ 39.964443] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 > [ 39.964872] cs: IO port probe 0x820-0x8ff: clean. > [ 39.965235] cs: IO port probe 0xc00-0xcf7: clean. > [ 39.965737] cs: IO port probe 0xa00-0xaff: clean. > [ 39.966320] cs: IO port probe 0x100-0x3af: clean. > [ 39.967340] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 > [ 39.967768] cs: IO port probe 0x820-0x8ff: clean. > [ 39.968131] cs: IO port probe 0xc00-0xcf7: clean. > [ 39.968635] cs: IO port probe 0xa00-0xaff: clean. > [ 40.231725] lp0: using parport0 (interrupt-driven). > [ 40.636109] EXT3 FS on loop0, internal journal > [ 42.636994] IBM TrackPoint firmware: 0x0e, buttons: 3/3 > [ 42.858932] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input9 > [ 50.998537] Adding 976552k swap on /host/ubuntu/disks/swap.disk. Priority:-1 extents:1 across:976552k > [ 51.699761] ip_tables: (C) 2000-2006 Netfilter Core Team > [ 52.039839] PPP generic driver version 2.4.2 > [ 52.121682] NET: Registered protocol family 10 > [ 52.122041] lo: Disabled Privacy Extensions > [ 52.122819] ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 52.637776] ACPI: ACPI Dock Station Driver > [ 52.711584] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: found ejectable bay > [ 52.711591] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: Adding notify handler > [ 52.711633] ACPI: Error installing bay notify handler > [ 52.711637] ACPI: Bay [\_SB_.PCI0.IDE0.SCND.MSTR] Added > [ 54.387191] IBM machine detected. Enabling interrupts during APM calls. > [ 54.387198] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) > [ 54.387201] apm: overridden by ACPI. > [ 54.501628] ppdev: user-space parallel port driver > [ 54.735767] audit(1210436815.229:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=4928 profile="/usr/sbin/cupsd" namespace="default" > [ 54.859179] input: /usr/sbin/thinkpad-keys as /devices/virtual/input/input10 > [ 73.398002] Marking TSC unstable due to: cpufreq changes. > [ 148.532545] Bluetooth: Core ver 2.11 > [ 148.534046] NET: Registered protocol family 31 > [ 148.534055] Bluetooth: HCI device and connection manager initialized > [ 148.534064] Bluetooth: HCI socket layer initialized > [ 55.755731] Bluetooth: L2CAP ver 2.9 > [ 55.755736] Bluetooth: L2CAP socket layer initialized > [ 55.855828] Bluetooth: RFCOMM socket layer initialized > [ 55.856301] Bluetooth: RFCOMM TTY layer initialized > [ 55.856305] Bluetooth: RFCOMM ver 1.8 > [ 57.153757] [drm] Initialized drm 1.1.0 20060810 > [ 152.462742] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 > [ 152.463396] [drm] Initialized radeon 1.28.0 20060524 on minor 0 > [ 58.193324] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. > [ 58.193863] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode > [ 58.194349] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode > [ 155.351588] [drm] Setting GART location based on new memory map > [ 155.351661] [drm] writeback test succeeded in 1 usecs > [ 206.276212] usb 4-4: new high speed USB device using ehci_hcd and address 3 > [ 206.409685] usb 4-4: configuration #1 chosen from 1 choice > [ 207.096497] usbcore: registered new interface driver libusual > [ 77.689045] Initializing USB Mass Storage driver... > [ 77.691071] scsi2 : SCSI emulation for USB Mass Storage devices > [ 77.692466] usbcore: registered new interface driver usb-storage > [ 77.692472] USB Mass Storage support registered. > [ 77.693346] usb-storage: device found at 3 > [ 77.693349] usb-storage: waiting for device to settle before scanning > [ 207.419350] usb-storage: device scan complete > [ 207.420860] scsi 2:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 3.27 PQ: 0 ANSI: 2 > [ 207.422855] scsi 2:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 3.27 PQ: 0 ANSI: 2 > [ 207.426064] sd 2:0:0:0: [sdb] 4001422 512-byte hardware sectors (2049 MB) > [ 207.427941] sd 2:0:0:0: [sdb] Write Protect is off > [ 207.427951] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00 > [ 207.427959] sd 2:0:0:0: [sdb] Assuming drive cache: write through > [ 207.433435] sd 2:0:0:0: [sdb] 4001422 512-byte hardware sectors (2049 MB) > [ 207.435313] sd 2:0:0:0: [sdb] Write Protect is off > [ 207.435324] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00 > [ 207.435330] sd 2:0:0:0: [sdb] Assuming drive cache: write through > [ 207.438194] sdb: sdb1 > [ 207.439825] sd 2:0:0:0: [sdb] Attached SCSI removable disk > [ 207.440910] sd 2:0:0:0: Attached scsi generic sg2 type 0 > [ 207.446187] sr1: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray > [ 77.792803] sr 2:0:0:1: Attached scsi CD-ROM sr1 > [ 77.793158] sr 2:0:0:1: Attached scsi generic sg3 type 5 > [ 224.834630] usb 4-4: USB disconnect, address 3 > [ 224.835646] scsi 2:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK > [ 224.835660] end_request: I/O error, dev sdb, sector 3999733 > [ 224.835669] Buffer I/O error on device sdb1, logical block 3999488 > [ 224.835697] scsi 2:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK > [ 224.835707] end_request: I/O error, dev sdb, sector 3999734 > [ 224.835715] Buffer I/O error on device sdb1, logical block 3999489 > [ 224.835723] Buffer I/O error on device sdb1, logical block 3999490 > [ 224.835731] Buffer I/O error on device sdb1, logical block 3999491 > [ 224.835739] Buffer I/O error on device sdb1, logical block 3999492 > [ 224.835748] Buffer I/O error on device sdb1, logical block 3999493 > [ 224.835756] Buffer I/O error on device sdb1, logical block 3999494 > [ 224.835764] Buffer I/O error on device sdb1, logical block 3999495 > [ 224.835818] Buffer I/O error on device sdb1, logical block 3999488 > [ 224.835827] Buffer I/O error on device sdb1, logical block 3999489 > [ 224.844497] scsi 2:0:0:0: rejecting I/O to dead device > [ 224.844933] scsi 2:0:0:0: rejecting I/O to dead device > [ 224.845287] scsi 2:0:0:0: rejecting I/O to dead device > [ 224.845631] scsi 2:0:0:0: rejecting I/O to dead device > [ 224.845971] scsi 2:0:0:0: [sdb] READ CAPACITY failed > [ 224.845979] scsi 2:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK > [ 224.845990] scsi 2:0:0:0: [sdb] Sense not available. > [ 224.847137] scsi 2:0:0:0: rejecting I/O to dead device > [ 224.847476] scsi 2:0:0:0: [sdb] Write Protect is off > [ 224.847486] scsi 2:0:0:0: [sdb] Mode Sense: 00 00 00 00 > [ 224.847493] scsi 2:0:0:0: [sdb] Assuming drive cache: write through > [ 225.368227] usb 4-4: new high speed USB device using ehci_hcd and address 4 > [ 225.501584] usb 4-4: configuration #1 chosen from 1 choice > [ 225.509506] scsi3 : SCSI emulation for USB Mass Storage devices > [ 225.516351] usb-storage: device found at 4 > [ 225.516360] usb-storage: waiting for device to settle before scanning > [ 228.830331] usb-storage: device scan complete > [ 228.831329] scsi 3:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 3.27 PQ: 0 ANSI: 2 > [ 228.832193] scsi 3:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 3.27 PQ: 0 ANSI: 2 > [ 228.834283] sd 3:0:0:0: [sdb] 4001422 512-byte hardware sectors (2049 MB) > [ 228.835402] sd 3:0:0:0: [sdb] Write Protect is off > [ 228.835412] sd 3:0:0:0: [sdb] Mode Sense: 03 00 00 00 > [ 228.835419] sd 3:0:0:0: [sdb] Assuming drive cache: write through > [ 228.838779] sd 3:0:0:0: [sdb] 4001422 512-byte hardware sectors (2049 MB) > [ 228.839777] sd 3:0:0:0: [sdb] Write Protect is off > [ 228.839787] sd 3:0:0:0: [sdb] Mode Sense: 03 00 00 00 > [ 228.839794] sd 3:0:0:0: [sdb] Assuming drive cache: write through > [ 228.839804] sdb: sdb1 > [ 228.841571] sd 3:0:0:0: [sdb] Attached SCSI removable disk > [ 228.841669] sd 3:0:0:0: Attached scsi generic sg2 type 0 > [ 228.846025] sr1: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray > [ 228.846167] sr 3:0:0:1: Attached scsi CD-ROM sr1 > [ 228.846255] sr 3:0:0:1: Attached scsi generic sg3 type 5 > [ 254.408883] usb 4-4: USB disconnect, address 4 > [ 254.409548] printk: 23 messages suppressed. > [ 254.409556] Buffer I/O error on device sdb1, logical block 497 > [ 254.409565] lost page write due to I/O error on sdb1 > [ 254.409580] Buffer I/O error on device sdb1, logical block 137163 > [ 254.409587] lost page write due to I/O error on sdb1 > [ 487.517953] usb 4-4: new high speed USB device using ehci_hcd and address 5 > [ 487.651505] usb 4-4: configuration #1 chosen from 1 choice > [ 487.706039] scsi4 : SCSI emulation for USB Mass Storage devices > [ 487.714175] usb-storage: device found at 5 > [ 487.714185] usb-storage: waiting for device to settle before scanning > [ 493.278888] usb-storage: device scan complete > [ 493.279521] scsi 4:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 3.27 PQ: 0 ANSI: 2 > [ 493.280337] scsi 4:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 3.27 PQ: 0 ANSI: 2 > [ 493.283468] sd 4:0:0:0: [sdb] 4001422 512-byte hardware sectors (2049 MB) > [ 493.290855] sd 4:0:0:0: [sdb] Write Protect is off > [ 493.290865] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00 > [ 493.290872] sd 4:0:0:0: [sdb] Assuming drive cache: write through > [ 493.293463] sd 4:0:0:0: [sdb] 4001422 512-byte hardware sectors (2049 MB) > [ 493.294101] sd 4:0:0:0: [sdb] Write Protect is off > [ 493.294109] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00 > [ 493.294116] sd 4:0:0:0: [sdb] Assuming drive cache: write through > [ 493.294124] sdb: sdb1 > [ 493.295122] sd 4:0:0:0: [sdb] Attached SCSI removable disk > [ 493.295218] sd 4:0:0:0: Attached scsi generic sg2 type 0 > [ 493.299461] sr1: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray > [ 493.299591] sr 4:0:0:1: Attached scsi CD-ROM sr1 > [ 493.299678] sr 4:0:0:1: Attached scsi generic sg3 type 5 > [ 185.328470] cdrom: This disc doesn't have any tracks I recognize! > [ 186.054179] UDF-fs: No VRS found > [ 186.064159] ISO 9660 Extensions: Microsoft Joliet Level 3 > [ 186.065555] ISOFS: changing to secondary root > >
