Antonio,
I have tried with both servers, itelefonica and ig and I had always the
same problem, which is shown on the output of wvdial below. It says about DNS
failure, take a look:
[jfernando@bunitinhu ungrab-winmodem-20070505]$ sudo wvdial
--> WvDial: Internet dialer version 1.54.0
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT33550317
--> Waiting for carrier.
ATDT33550317
CONNECT 45333
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Mon May 5 18:42:48 2008
--> pid of pppd: 3347
--> Using interface ppp0
--> Authentication (PAP) started
--> Authentication (PAP) successful
--> local IP address 200.226.182.160
--> remote IP address 201.28.132.126
--> primary DNS address 200.225.159.124
--> secondary DNS address 200.225.159.126
--> Script /etc/ppp/ip-up run successful
--> Default route Ok.
--> warning, no nameserver found `/etc/resolv.conf`
--> Nameserver (DNS) failure, the connection may not work.
--> Connected... Press Ctrl-C to disconnect
On /etc/resolv.conf, I had put the following lines, with the '#' indicating
the itelefonica options:
search ig.com.br
ig.com.br 200.225.159.124
ig.com.br 200.225.159.126
#itelefonica.com.br
#itelefonica.com.br 200.204.0.138
#itelefonica.com.br 200.204.0.10
Any suggestion is welcome. Thank you.
On Mon, 5 May 2008 23:39:57 +0000, Antonio Olivares wrote
> Jose,
>
> I took a look into the page
>
> http://itelefonica.terra.com.br/ajuda/discador_a.htm
>
> and looks like the ISP works more with windows
>
> O discador é compatível com todos os sistemas operacionais?
> Não. O discador é compatível somente com Windows 95, 98, ME, NT,
> 2000 e XP.
>
> Translation.
>
> Is this service compatible with other operative systems?
> No, It is designed and compatible with only Windows 95, 98, ME, NT,
> 2000 e XP.
>
> However, do not let this discourage you. Marv, Jacques and others on
> this list are very capable and can share with you as how go about it
> and get connected with linux.
>
> Regards,
>
> Antonio
>
> On 5/5/08, Antonio Olivares <olivares14031@xxxxxxxxx> wrote:
> > Jose,
> >
> > Use the numbers and add a corresponding nameserver on
> > them so that /etc/resolv.conf looks like
> >
> > # cat /etc/resolv.conf
> > search example.net
> > nameserver 200.204.0.138
> > nameserver 200.204.0.10
> >
> > This should get you connected, if this does not
> > happen, Carefully read Jacques' post-install
> > troubleshooting guide
> >
> > http://linmodems.technion.ac.il/post-install.html
> >
> > Regards,
> >
> > Antonio
> >
> > --- Jose Fernando de Jesus
> > <jfernando@xxxxxxxxxxxxxxxx> wrote:
> >
> > > Antonio,
> > >
> > > I have followed all the steps you told me but I'm
> > > not still able to browse.
> > > The Network Manager is off. I did the eth0 down.
> > > About the file resolv.conf I
> > > have the following doubts: the output I have from
> > > wvdial is:
> > >
> > > [root@bunitinhu ~]# wvdial
> > > --> [root@bunitinhu ~]# wvdial
> > > --> WvDial: Internet dialer version 1.54.0
> > > --> Cannot get information for serial port.
> > > --> Initializing modem.
> > > --> Sending: ATZ
> > > ATZ
> > > OK
> > > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
> > > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
> > > OK
> > > --> Modem initialized.
> > > --> Sending: ATDT30095515
> > > --> Waiting for carrier.
> > > ATDT30095515
> > > CONNECT 46667
> > > --> Carrier detected. Waiting for prompt.
> > > UQKT2 78.1
> > > Login:
> > > --> Looks like a login prompt.
> > > --> Sending: jfernando1980@xxxxxxxxxxxxxxxxxx
> > > jfernando1980@xxxxxxxxxxxxxxxxxx
> > > Password:
> > > --> Looks like a password prompt.
> > > --> Sending: (password)
> > > Entering PPP Session.
> > > IP address is 201.93.49.96
> > > MTU is 1100.
> > > --> Looks like a welcome message.
> > > --> Starting pppd at Mon May 5 15:42:43 2008
> > > --> pid of pppd: 3323
> > > --> Using interface ppp0
> > > --> local IP address 201.93.49.96
> > > --> remote IP address 200.100.131.77
> > > --> primary DNS address 200.204.0.138
> > > --> secondary DNS address 200.204.0.10
> > > WvDial: Internet dialer version 1.54.0
> > > --> Cannot get information for serial port.
> > > --> Initializing modem.
> > > --> Sending: ATZ
> > > ATZ
> > > OK
> > > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
> > > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
> > > OK
> > > --> Modem initialized.
> > > --> Sending: ATDT30095515
> > > --> Waiting for carrier.
> > > ATDT30095515
> > > CONNECT 46667
> > > --> Carrier detected. Waiting for prompt.
> > > UQKT2 78.1
> > > Login:
> > > --> Looks like a login prompt.
> > > --> Sending: jfernando1980@xxxxxxxxxxxxxxxxxx
> > > jfernando1980@xxxxxxxxxxxxxxxxxx
> > > Password:
> > > --> Looks like a password prompt.
> > > --> Sending: (password)
> > > Entering PPP Session.
> > > IP address is 201.93.49.96
> > > MTU is 1100.
> > > --> Looks like a welcome message.
> > > --> Starting pppd at Mon May 5 15:42:43 2008
> > > --> pid of pppd: 3323
> > > --> Using interface ppp0
> > > --> local IP address 201.93.49.96
> > > --> remote IP address 200.100.131.77
> > > --> primary DNS address 200.204.0.138
> > > --> secondary DNS address 200.204.0.10
> > >
> > > Is these 2 last numbers that I have to put on the
> > > /etc/resolv.conf file? Is
> > > the name server the name of the server I want to
> > > connect to? Should it be
> > > given the complete server name, with dots?
> > > I have already tried all of it, but I'm still not
> > > able to browse. Either I
> > > did not understand this step or the nameserver I
> > > have is wrong. I have tried
> > > itelefonica.com.br, which is the last part of my
> > > dialer login.
> > >
> > > Thank you.
> > >
> > >
> > >
> > > On Mon, 5 May 2008 05:03:20 -0700 (PDT), Antonio
> > > Olivares wrote
> > > > Jose,
> > > >
> > > > Check to see if NetworkManager and NetworkManager
> > > dispatcher are running
> > > >
> > > > # chkconfig NetworkManager --list
> > > > if they are on, turn them off by doing a
> > > > # service NetworkManager off
> > > > and turn it off from starting completely do a
> > > > # chkconfig NetworkManager off
> > > > then look for your settings ie, which DNS(Domain
> > > Name Servers) you
> > > > need for your ISP, and put them into your
> > > /etc/resolv.conf an
> > > > example would be
> > > >
> > > > cat /etc/resolv.conf
> > > > nameserver 19.190.128.1
> > > > nameserver 19.195.128.1
> > > >
> > > > Also turn off eth0 connection by doing a
> > > > # ifconfig eth0 down
> > > > then try to connect again.
> > > >
> > > > HTH,
> > > >
> > > > Antonio
> > > >
> > > > ----- Original Message ----
> > > > From: Jose Fernando de Jesus
> > > <jfernando@xxxxxxxxxxxxxxxx>
> > > > To: Antonio Olivares <olivares14031@xxxxxxxxx>
> > > > Sent: Sunday, May 4, 2008 9:02:17 PM
> > > > Subject: Re: Fernando, Brazil Fedora release 7
> > > (Moonshine) Kernel
> > > > kernel 2.6.21-1.3194.fc7
> > > >
> > > > Hi, finally I was able to connect using the
> > > scripts you sent me,
> > > > but I was not able to browse. Is there any
> > > settings I have to
> > > > provide to Firefox? What should I do?
> > > >
> > > > Thanks a lot.
> > > >
> > > > On Sun, 4 May 2008 17:27:37 -0700 (PDT), Antonio
> > > Olivares wrote
> > > > > Jose,
> > > > >
> > > > > for a working example you may look here for
> > > automation
> > > > >
> > > > >
> > >
> > http://www20.brinkster.com/olivares/slmodemd-setup-1.html
> > > > >
> > > > > I did not update it for Fedora 7/8 but it works
> > > the
> > > > > same, you can add the line that Marv told you to
> > > > > /etc/modprobe.conf as su -(Super User), then
> > > also # cp
> > > > > slmodem-2.9.11-20080417/scripts/slmodemd
> > > > > /etc/rc.d/init.d/
> > > > > # cd /etc/rc.d/init.d/
> > > > > [root@localhost init.d]# chmod +x slmodemd
> > > > > [root@localhost init.d]# chkconfig slmodemd
> > > --add
> > > > > [root@localhost init.d]# chkconfig slmodemd on
> > > > >
> > > > > Should take care of it. You might need the
> > > lines
> > > > >
> > > > > modprobe ungrab-winmodem
> > > > > modprobe slamr
> > > > >
> > > > > in start procedure in the case that upon startup
> > > you
> > > > > see ``slmodemd dead but subsys locked'' message
> > > > >
> > > > > start() {
> > > > > modprobe ungrab-winmodem
> > > > > modprobe slamr
> > > > > echo -n "Starting SmartLink Modem driver
> > > for
> > > > > $SLMODEMD_DEVICE: "
> > > > > $prog /dev/null 2>/dev/null \
> > > > > --country=$SLMODEMD_COUNTRY
> > > $SLMODEMD_OPTS
> > > > > /dev/$SLMODEMD_DEVICE &
> > > > > RETVAL=$?
> > > > > [ $RETVAL -eq 0 ] && success $"$prog
> > > startup"
> > > > > || failure $"$prog startup"
> > > > > echo
> > > > > [ $RETVAL -eq 0 ] && touch
> > > > > /var/lock/subsys/$prog
> > > > > return $RETVAL
> > > > > }
> > > > >
> > > > > Regards,
> > > > >
> > > > > Antonio
> > > > >
> > > > > --- Marvin Stodolsky
> > > <marvin.stodolsky@xxxxxxxxx>
> > >
> > === message truncated ===
> >
> >
> >
> >
> >
____________________________________________________________________________________
> > Be a better friend, newshound, and
> > know-it-all with Yahoo! Mobile. Try it now.
> > http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
> >
José Fernando de Jesus
Physics Graduated
PhD Student on Cosmology (IAG-USP)
Rua do Matão 1226
Cidade Universitária
05508-900 São Paulo SP
Brasil
Phone: 55 11 30912732
email: jfernando@xxxxxxxxxxxxxxxx
(:¿©2007©?:)
Rock'n'Roll!
