Jose, Use the numbers and add a corresponding nameserver on them so that /etc/resolv.conf looks like # cat /etc/resolv.conf search example.net nameserver 200.204.0.138 nameserver 200.204.0.10 This should get you connected, if this does not happen, Carefully read Jacques' post-install troubleshooting guide http://linmodems.technion.ac.il/post-install.html Regards, Antonio --- Jose Fernando de Jesus <jfernando@xxxxxxxxxxxxxxxx> wrote: > Antonio, > > I have followed all the steps you told me but I'm > not still able to browse. > The Network Manager is off. I did the eth0 down. > About the file resolv.conf I > have the following doubts: the output I have from > wvdial is: > > [root@bunitinhu ~]# wvdial > --> [root@bunitinhu ~]# wvdial > --> WvDial: Internet dialer version 1.54.0 > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Modem initialized. > --> Sending: ATDT30095515 > --> Waiting for carrier. > ATDT30095515 > CONNECT 46667 > --> Carrier detected. Waiting for prompt. > UQKT2 78.1 > Login: > --> Looks like a login prompt. > --> Sending: jfernando1980@xxxxxxxxxxxxxxxxxx > jfernando1980@xxxxxxxxxxxxxxxxxx > Password: > --> Looks like a password prompt. > --> Sending: (password) > Entering PPP Session. > IP address is 201.93.49.96 > MTU is 1100. > --> Looks like a welcome message. > --> Starting pppd at Mon May 5 15:42:43 2008 > --> pid of pppd: 3323 > --> Using interface ppp0 > --> local IP address 201.93.49.96 > --> remote IP address 200.100.131.77 > --> primary DNS address 200.204.0.138 > --> secondary DNS address 200.204.0.10 > WvDial: Internet dialer version 1.54.0 > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Modem initialized. > --> Sending: ATDT30095515 > --> Waiting for carrier. > ATDT30095515 > CONNECT 46667 > --> Carrier detected. Waiting for prompt. > UQKT2 78.1 > Login: > --> Looks like a login prompt. > --> Sending: jfernando1980@xxxxxxxxxxxxxxxxxx > jfernando1980@xxxxxxxxxxxxxxxxxx > Password: > --> Looks like a password prompt. > --> Sending: (password) > Entering PPP Session. > IP address is 201.93.49.96 > MTU is 1100. > --> Looks like a welcome message. > --> Starting pppd at Mon May 5 15:42:43 2008 > --> pid of pppd: 3323 > --> Using interface ppp0 > --> local IP address 201.93.49.96 > --> remote IP address 200.100.131.77 > --> primary DNS address 200.204.0.138 > --> secondary DNS address 200.204.0.10 > > Is these 2 last numbers that I have to put on the > /etc/resolv.conf file? Is > the name server the name of the server I want to > connect to? Should it be > given the complete server name, with dots? > I have already tried all of it, but I'm still not > able to browse. Either I > did not understand this step or the nameserver I > have is wrong. I have tried > itelefonica.com.br, which is the last part of my > dialer login. > > Thank you. > > > > On Mon, 5 May 2008 05:03:20 -0700 (PDT), Antonio > Olivares wrote > > Jose, > > > > Check to see if NetworkManager and NetworkManager > dispatcher are running > > > > # chkconfig NetworkManager --list > > if they are on, turn them off by doing a > > # service NetworkManager off > > and turn it off from starting completely do a > > # chkconfig NetworkManager off > > then look for your settings ie, which DNS(Domain > Name Servers) you > > need for your ISP, and put them into your > /etc/resolv.conf an > > example would be > > > > cat /etc/resolv.conf > > nameserver 19.190.128.1 > > nameserver 19.195.128.1 > > > > Also turn off eth0 connection by doing a > > # ifconfig eth0 down > > then try to connect again. > > > > HTH, > > > > Antonio > > > > ----- Original Message ---- > > From: Jose Fernando de Jesus > <jfernando@xxxxxxxxxxxxxxxx> > > To: Antonio Olivares <olivares14031@xxxxxxxxx> > > Sent: Sunday, May 4, 2008 9:02:17 PM > > Subject: Re: Fernando, Brazil Fedora release 7 > (Moonshine) Kernel > > kernel 2.6.21-1.3194.fc7 > > > > Hi, finally I was able to connect using the > scripts you sent me, > > but I was not able to browse. Is there any > settings I have to > > provide to Firefox? What should I do? > > > > Thanks a lot. > > > > On Sun, 4 May 2008 17:27:37 -0700 (PDT), Antonio > Olivares wrote > > > Jose, > > > > > > for a working example you may look here for > automation > > > > > > > http://www20.brinkster.com/olivares/slmodemd-setup-1.html > > > > > > I did not update it for Fedora 7/8 but it works > the > > > same, you can add the line that Marv told you to > > > /etc/modprobe.conf as su -(Super User), then > also # cp > > > slmodem-2.9.11-20080417/scripts/slmodemd > > > /etc/rc.d/init.d/ > > > # cd /etc/rc.d/init.d/ > > > [root@localhost init.d]# chmod +x slmodemd > > > [root@localhost init.d]# chkconfig slmodemd > --add > > > [root@localhost init.d]# chkconfig slmodemd on > > > > > > Should take care of it. You might need the > lines > > > > > > modprobe ungrab-winmodem > > > modprobe slamr > > > > > > in start procedure in the case that upon startup > you > > > see ``slmodemd dead but subsys locked'' message > > > > > > start() { > > > modprobe ungrab-winmodem > > > modprobe slamr > > > echo -n "Starting SmartLink Modem driver > for > > > $SLMODEMD_DEVICE: " > > > $prog /dev/null 2>/dev/null \ > > > --country=$SLMODEMD_COUNTRY > $SLMODEMD_OPTS > > > /dev/$SLMODEMD_DEVICE & > > > RETVAL=$? > > > [ $RETVAL -eq 0 ] && success $"$prog > startup" > > > || failure $"$prog startup" > > > echo > > > [ $RETVAL -eq 0 ] && touch > > > /var/lock/subsys/$prog > > > return $RETVAL > > > } > > > > > > Regards, > > > > > > Antonio > > > > > > --- Marvin Stodolsky > <marvin.stodolsky@xxxxxxxxx> > === message truncated === ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
