Dear Marvin, Thank you for your help with configuring. I put down both eth0 and eth1 and now I can browse and send-and-receive. I'm writing this online. This was the line you requested from lsusb... Bus 004 Device 004: ID 1004:1fae LG Electronics, Inc. U8120 3G Cellphone If you need more info for research, I'll be glad to comply. Thanks again, Aaron ----- Original Message ---- From: Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> To: Aaron Ulrich <aarondulrich@xxxxxxxxx> Sent: Sunday, March 2, 2008 2:24:17 AM Subject: Re: Aaron, Ghana, kernel 2.6.22-14-generic Re: ran ScanModem but I don't think it recognized the phone Would you please run $ lsusb and copy me the lines representing the modem Also look though folders of /proc/bus/usb /sys/bus/usb and copy out any info on the modem. I would like to understand why scanModem didn't detect the USB modem MarvS On Sat, Mar 1, 2008 at 5:34 PM, Aaron Ulrich <aarondulrich@xxxxxxxxx> wrote: > Hello, > I'm not old with Linux. I'm trying to get this Dell Inspiron 6000 connected > to the internet through an external USB LG U8330C phone. It works with > Windows. I ran ScanModem but I don't think it recognized the phone. When I > ran wvdialconf, this was the output: > > aaron@CCM12:~$ sudo wvdialconf > [sudo] password for aaron: > Editing `/etc/wvdial.conf'. > > Scanning your serial ports for a modem. > > Modem Port Scan<*1>: S0 S1 S2 S3 > WvModem<*1>: Cannot get information for serial port. > ttyACM0<*1>: ATQ0 V1 E1 -- OK > ttyACM0<*1>: ATQ0 V1 E1 Z -- OK > ttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OK > ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK > ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK > ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > ttyACM0<*1>: Modem Identifier: ATI -- LGE U8xxx > ttyACM0<*1>: Speed 4800: AT -- OK > ttyACM0<*1>: Speed 9600: AT -- OK > ttyACM0<*1>: Speed 19200: AT -- OK > ttyACM0<*1>: Speed 38400: AT -- OK > ttyACM0<*1>: Speed 57600: AT -- OK > ttyACM0<*1>: Speed 115200: AT -- OK > ttyACM0<*1>: Speed 230400: AT -- OK > ttyACM0<*1>: Speed 460800: AT -- OK > ttyACM0<*1>: Max speed is 460800; that should be safe. > ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > WvModem<*1>: Cannot get information for serial port. > ttyACM1<*1>: ATQ0 V1 E1 -- OK > ttyACM1<*1>: ATQ0 V1 E1 Z -- OK > ttyACM1<*1>: ATQ0 V1 E1 S0=0 -- OK > ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK > ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK > ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > ttyACM1<*1>: Modem Identifier: ATI -- LGE U8xxx > ttyACM1<*1>: Speed 4800: AT -- OK > ttyACM1<*1>: Speed 9600: AT -- OK > ttyACM1<*1>: Speed 19200: AT -- OK > ttyACM1<*1>: Speed 38400: AT -- OK > ttyACM1<*1>: Speed 57600: AT -- OK > ttyACM1<*1>: Speed 115200: AT -- OK > ttyACM1<*1>: Speed 230400: AT -- OK > ttyACM1<*1>: Speed 460800: AT -- OK > ttyACM1<*1>: Max speed is 460800; that should be safe. > ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > > Found an USB modem on /dev/ttyACM0. > Modem configuration written to /etc/wvdial.conf. > ttyACM0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" > ttyACM1<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" > aaron@CCM12:~$ > > Then I edited /etc/wvdial.conf as follows: > > [Dialer Defaults] > Modem = /dev/ttyACM0 > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > Init3 = AT+CGDCONT =1,"IP","WEB.TIGO.COM.GH" > Stupid Mode = 1 > Modem Type = USB Modem > Phone = *99# > New PPPD = yes > ISDN = 0 > Username = 0 > Password = 0 > Baud = 230400 > Auto DNS = yes > > Then I ran wvdial. Following is the output it gave: > > aaron@CCM12:~$ sudo wvdial > WvDial<*1>: WvDial: Internet dialer version 1.56 > WvModem<*1>: Cannot get information for serial port. > WvDial<*1>: Initializing modem. > WvDial<*1>: Sending: ATZ > WvDial Modem<*1>: ATZ > WvDial Modem<*1>: OK > WvDial<*1>: Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > WvDial Modem<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > WvDial Modem<*1>: OK > WvDial<*1>: Sending: AT+CGDCONT =1,"IP","WEB.TIGO.COM.GH" > WvDial Modem<*1>: AT+CGDCONT =1,"IP","WEB.TIGO.COM.GH" > WvDial Modem<*1>: OK > WvDial<*1>: Modem initialized. > WvDial<*1>: Sending: ATDT*99# > WvDial<*1>: Waiting for carrier. > WvDial Modem<*1>: ATDT*99# > WvDial Modem<*1>: CONNECT > WvDial Modem<*1>: ~[7f]}#@!}!}!} }9}#}%B#}%}(}"}'}"}"}&} } } } }%}&.3E}.t ~ > WvDial<*1>: Carrier detected. Starting PPP immediately. > WvDial<Notice>: Starting pppd at Sat Mar 1 22:09:37 2008 > WvDial<Notice>: Pid of pppd: 6641 > WvDial<*1>: Using interface ppp0 > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: local IP address 10.10.31.160 > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: remote IP address 10.64.64.64 > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: primary DNS address 212.96.1.70 > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > WvDial<*1>: secondary DNS address 212.96.16.61 > WvDial<*1>: pppd: 8?[06][08][08]?[06][08](?[06][08] > > I tried to browse and download emails - failure. Where do I go from here? > Thanks allot, > Aaron >
