Testing this modem with ./scanModem test PCI:ID
I get the following:
Primary PCI_id 8086:27d8
Subsystem PCI_id 1462:0531
Softmodem codec or chipset from diagnostics:
from Archives:
Lacking a dsp (digital signal processing) chip, the modem is a software
intensive or "softmodem" type. Its primary controller manages the traffic
with the CPU. But the software needed is specified in the Subsystem.
-----------------------------------------
Support type needed or chipset:
Support can likely be achieved through two mutually exclusive alternatives:
1) The hsfmodem software for Conexant chipset modems: Read Conexant.txt
The following ALSA alternative CANNOT work with Conexant modems.
2) An ALSA modem driver plus slmodemd. Read Smartlink.txt for details, and
to test get the package SLMODEMD.gcc4.1.tar.gz from:
http://linmodems.technion.ac.il/packages/smartlink/
Writing Intel.txt
For owners of a Dell PCs with Conexant HSF modems, a driver source
package with full speed enabled is available, but requires driver
compiling. Read Conexant.txt
Read Conexant.txt
Writing Conexant.txt
Writing Smartlink.txt
============ end Smartlink section =====================
Alexey,
scanModem reports that you also have an IRQ problem
Modem interrupt assignment and sharing:
16: 1908 74131905 IO-APIC-fasteoi uhci_hcd:usb5,
sdhci:slot0, ohci1394, HDA Intel, yenta, i915@pci:0000:00:02.0
--- Bootup diagnostics for card in PCI slot 00:1b.0 ----
you need to read Bootup.txt and do what is there and send that to
discuss@xxxxxxxxxxxxx/Marv. So this modem is either or situation
unless Marv can point out which one it is.
Thanks,
Antonio
On Jan 13, 2008 6:34 AM, Jacques Goldberg <Jacques.Goldberg@xxxxxxx> wrote:
> Alexey,
> The tool which you have used to try to dial does not show relevant
> information, at least at my level of understanding.
>
> Give the following command
> slmodemd -a hw:0,6 -d 9 -c LATVIA
> and DO NOT STOP IT.
> In an other window, as root (su) give the command
> wvdialconf /etc/wvdial.conf
> If this detects the modem, it will work: then, edit the file
> /etc/wvdial.conf
> Three things are obvious: phone number, username, password.
> For these three lines remove ; > and < and replace the word which was in
> < ... > by its value given by your ISP
> Last thing, add one line:
> Carrier Check = no
> Save and exit the editor.
>
> Next, just type
> wvdial
> and you should be connected.
> wvdial and slmodemd are stopped by typing CTRL-C once you does not need
> them anynore (close the connection)
>
> Jacques
>
>
> Alexey Pechenkin wrote:
> > Hi,
> >
> > I have MSI L740 laptop with a built-in Si3054 modem. I'm trying to make
> > it work on SUSE 10.3 with a stock snd_hda_intel driver from kernel
> > 2.6.22.13.
> > I compiled slmodem, applied the 'size 48' patch, and tried to call
> > several dialup numbers. None of them worked, the modem always reports NO
> > CARRIER after some delay.
> > Any help would be appreciated.
> > Here is the debug output from slmodem:
> >
> > slmodemd -a hw:0,6 -d 9 -c LATVIA
> > SmartLink Soft Modem: version 2.9.11 Jan 5 2008 22:13:27
> > <087.254493> SmartLink Soft Modem: version 2.9.11 Jan 5 2008 22:13:27
> > <087.254636> hw:0,6: startup modem...
> > <087.254826> hw:0,6: update termios...
> > symbolic link `/dev/ttySL0' -> `/dev/pts/2' created.
> > modem `hw:0,6' created. TTY is `/dev/pts/2'
> > <087.255316> open file: /var/lib/slmodem/data.hw:0,6...
> > <087.257120> main: rt applyed: SCHED_FIFO, pri 99
> > Use `/dev/ttySL0' as modem device, Ctrl+C for termination.
> > <090.899182> main: termios changed.
> > <090.899204> hw:0,6: update termios...
> > <091.375133> hw:0,6: run cmd: atz
> > <091.375156> hw:0,6: modem reset...
> > <091.375164> hw:0,6: modem set state: 1 --> 1...
> > <091.375174> hw:0,6: modem set mode: -> 0...
> > <091.375182> hw:0,6: modem report result: 0 (OK)
> > <094.038758> hw:0,6: run cmd: atx3
> > <094.038783> hw:0,6: modem report result: 0 (OK)
> > <527.756170> hw:0,6: run cmd: atdt9008080
> > <527.756202> hw:0,6: modem dial: t9008080...
> > <527.756210> hw:0,6: modem_dial_start...
> > <527.756216> call: create...
> > <527.756226> CallProgFP_Create >>
> > <527.756236> APPLY_FILTER = 0
> > <527.756244> Detection Thresholds: levle_fix=45,--> LEVEL_THRESHOLD=90
> > <527.756252> ============> 0
> > <527.756258> Cadence: Busy Tone loose detection is 0
> > <527.756266> TYPE BUSY
> > <527.756272> Filter index 0
> > <527.756277> Filter SubIndex 0
> > <527.756283> MAX_ON_TIME 27 Buffers MIN_ON_TIME 10 Buffers
> > <527.756289> MAX_OFF_TIME 27 Buffers MIN_OFF_TIME 10 Buffers
> > <527.756296> OFF_TIME_THAT_RESETS_CYCLE 81
> > <527.756301> BUFFER LENGTH 160 samples.
> > <527.756307> INTEGRATION_LENGTH 0[ms]
> > <527.756313> LEVEL 90
> > <527.756322> INTEGRATION_TIME = 0 Buffers.
> > <527.756329> Detection Thresholds: levle_fix=45,--> LEVEL_THRESHOLD=90
> > <527.756337> TYPE DIAL
> > <527.756342> Filter index 3
> > <527.756348> Filter SubIndex 0
> > <527.756353> MAX_ON_TIME 0 Buffers MIN_ON_TIME 0 Buffers
> > <527.756359> MAX_OFF_TIME 0 Buffers MIN_OFF_TIME 0 Buffers
> > <527.756366> OFF_TIME_THAT_RESETS_CYCLE 0
> > <527.756372> BUFFER LENGTH 666 samples.
> > <527.756377> INTEGRATION_LENGTH 200[ms]
> > <527.756383> LEVEL 90
> > <527.756390> INTEGRATION_TIME = 1 Buffers.
> > <527.756398> CALLPROG Create <<
> > <527.756404> CALLPROG Dialing t9008080
> > <527.756411> Configuration->tone_DigitLength 100
> > <527.756417> Configuration->pulse_OffHookTime 40
> > <527.756423> Configuration->pulse_OnHookTime 60
> > <527.756430> Configuration->dialPauseTime 4
> > <527.756436> Configuration->flashTime 7
> > <527.756442> Configuration->toneOrPulseFlag 0
> > <527.756448> Configuration->dialModifierValidationFlag 0
> > <527.756454> Configuration->ABCD_PermittedFlag 0
> > <527.756459> Configuration->pulseAndToneInSameStringPermittedFlag 0
> > <527.756466> Configuration->callingToneFlag 0
> > <527.756471> Configuration->commaPauseDurLimit 30
> > <527.756477> Configuration->digitPattern 1
> > <527.756483> Configuration->tone_BetweenDigitsInterval 100
> > <527.756489> Configuration->pulse_BetweenDigitsInterval 800
> > <527.756496> DTMF_Gain1 = 10337
> > <527.756501> DTMF_Gain2 = 13014
> > <527.756508> AnalyzeDialString: Updated 17 May 1999 00:50
> > <527.756514> AnalyzeDialString: LAST_DIALABLE_SYMBOL is 7
> > <527.756520> Dial String Syntax is VALID
> > <527.756529> GetNoAnswerTimeOut. 60
> > <527.756535> BlindCall: GetBlindDialPause = 2 .
> > <527.756541> CALLPROG_Dial was exited.
> > <527.756547> call: create RC: 9600 <-> 8000...
> > <527.756556> hw:0,6: modem_start..
> > <527.756562> hw:0,6: modem set state: 1 --> 2...
> > <527.756569> hw:0,6: new state: DP_ESTAB
> > <527.756575> main: alsa_ioctl: cmd 8, arg 3...
> > <527.756582> hw:0,6: modem set hook: 0 --> 1...
> > <527.756588> main: alsa_ioctl: cmd 2, arg 1...
> > <527.756715> main: alsa_ioctl: cmd 11, arg 0...
> > <527.756797> main: alsa_ioctl: cmd 4, arg 2580...
> > <527.756805> main: alsa_ioctl: cmd 7, arg 30...
> > <527.756811> main: alsa_start...
> > Hardware PCM card 0 'HDA Intel' device 6 subdevice 0
> > Its setup is:
> > stream : PLAYBACK
> > access : RW_INTERLEAVED
> > format : S16_LE
> > subformat : STD
> > channels : 1
> > rate : 9600
> > exact rate : 9600 (9600/1)
> > msbits : 16
> > buffer_size : 2048
> > period_size : 64
> > period_time : 6666
> > tick_time : 4000
> > tstamp_mode : NONE
> > period_step : 1
> > sleep_min : 0
> > avail_min : 4
> > xfer_align : 4
> > start_threshold : 2147483647
> > stop_threshold : 2048
> > silence_threshold: 0
> > silence_size : 0
> > boundary : 1073741824
> > Hardware PCM card 0 'HDA Intel' device 6 subdevice 0
> > Its setup is:
> > stream : CAPTURE
> > access : RW_INTERLEAVED
> > format : S16_LE
> > subformat : STD
> > channels : 1
> > rate : 9600
> > exact rate : 9600 (9600/1)
> > msbits : 16
> > buffer_size : 2048
> > period_size : 64
> > period_time : 6666
> > tick_time : 4000
> > tstamp_mode : NONE
> > period_step : 1
> > sleep_min : 0
> > avail_min : 4
> > xfer_align : 4
> > start_threshold : 2147483647
> > stop_threshold : 2048
> > silence_threshold: 0
> > silence_size : 0
> > boundary : 1073741824
> > <527.785785> main: startup write: 384...
> > <527.792526> call: process: msg 18 --> 0
> > <529.385844> DCR: initial DC Evaluation done, DC level -192, enabled
> > <529.792528> CALLPROG: Time out
> > <529.792551> STATE: CALLPROG_WAIT_DIAL --> CALLPROG_DIALING
> > <529.792569> call: process: msg 0 --> 3
> > <529.799196> DIALER_INITIAL_STATE
> > <529.799208> Digit is t
> > <529.799215> Dialer.c: GetNextDigit... TONE_OR_PULSE_FLAG became
> > TONE_DIALING
> > <529.799222> Digit is 9
> > <529.799229> Samples left = 800
> > <529.799250> call: process: msg 3 --> 0
> > <529.892536> Done Generating digit
> > <529.992534> Done Generating silence between digits
> > <529.992556> Digit is 0
> > <529.992563> Samples left = 800
> > <530.092533> Done Generating digit
> > <530.192530> Done Generating silence between digits
> > <530.192556> Digit is 0
> > <530.192563> Samples left = 800
> > <530.292541> Done Generating digit
> > <530.392539> Done Generating silence between digits
> > <530.392565> Digit is 8
> > <530.392573> Samples left = 800
> > <530.492544> Done Generating digit
> > <530.592542> Done Generating silence between digits
> > <530.592567> Digit is 0
> > <530.592575> Samples left = 800
> > <530.692547> Done Generating digit
> > <530.792546> Done Generating silence between digits
> > <530.792572> Digit is 8
> > <530.792579> Samples left = 800
> > <530.892550> Done Generating digit
> > <530.992545> Done Generating silence between digits
> > <530.992569> Digit is 0
> > <530.992577> Samples left = 800
> > <531.092553> Done Generating digit
> > <531.099212> DIALER_END_STATE
> > <531.099224> STATE: CALLPROG_DIALING --> CALLPROG_WAIT_RING
> > <531.099243> call: process: msg 0 --> 4
> > <531.105901> call: process: msg 4 --> 0
> > <534.779278> CYCLES_COUNTER= 1
> > <541.806089> Found 2250
> > <541.806123> call: process: msg 0 --> 17
> > <541.806132> hw:0,6: 134528: change dp: --> 8...
> > <541.806141> v8: create: caller 1, automode 0, dp id 92.
> > <541.806152> V8: Create called, V8 version 23/09/03 .
> > <541.806158> ############################################################
> > <541.806165> V8: local configuration :
> > <541.806174> Side = Caller
> > <541.806180> Operation Mode = 0
> > <541.806187> Modulations - V90=1, V34=1, V34HD=0, V32=1, V22=0,
> > V17=0, V29=0, V27=0, V23=0, V21=0
> > <541.806197> Call Functions - Data=1, CallRxFax=0, CallTxFax=0, V.80=0
> > <541.806205> Protocol - LAPM V.42
> > <541.806211> v8bisIndication - 0
> > <541.806217> timeouts - signal detect 12 sec, message detect 7 sec
> > <541.806224> quickConnectEnabled - 1
> > <541.806230> lapmIndication - 1
> > <541.806236> ucodeForQts - 9
> > <541.806242> ansPcmLevel - 0
> > <541.806248> ############################################################
> > <541.806260> V8: Initial CM message length is 9 octets
> > <541.806268> call: delete...
> > <541.806273> Dialer was aborted.
> > <541.806279> CALLPROG_Delete is entered
> > <541.806284> cadence_delete with CADENCE_DIAL_OBJ is invoked
> > <541.806291> cadence_delete with CADENCE_OBJ is invoked
> > <541.806298> CALLPROG_Delete is exited
> > <541.812749> V8: State changed from V8_INIT to V8_ORG_WAITING_FOR_ANSAM
> > <541.812766> v8: status (6) V8_ORG_WAITING_FOR_ANSAM
> > <550.652855> V8AGC, overflow = 0xfffffdb0,
> > <550.652879> V8AGC, overflow = 0x262,
> > <553.812897> V8: Time Out Waiting For ANSam...
> > <553.812924> V8: State changed from V8_ORG_WAITING_FOR_ANSAM to
> > V8_ORG_TIME_OUT_WAITING_FOR_ANSAM
> > <553.812934> v8: process: timeout.
> > <553.812941> v8: status (11) V8_ORG_TIME_OUT_WAITING_FOR_ANSAM
> > <553.812948> hw:0,6: modem_update_status: 512
> > <553.812956> hw:0,6: --> FINISH.
> > <553.812963> hw:0,6: modem_hup...
> > <553.812969> hw:0,6: modem set state: 2 --> 9...
> > <553.812977> hw:0,6: new state: DP_DISC
> > <553.812985> v8: process: timeout.
> > <553.812992> hw:0,6: modem_update_status: 512
> > <553.812999> hw:0,6: --> FINISH.
> > <553.813005> hw:0,6: modem_hup...
> > <553.813011> hw:0,6: modem_stop..
> > <553.813018> main: alsa_stop...
> > <553.827201> hw:0,6: modem set hook: 1 --> 0...
> > <553.827221> main: alsa_ioctl: cmd 2, arg 0...
> > <553.827373> main: alsa_ioctl: cmd 8, arg 0...
> > <553.827383> v8: delete...
> > <553.827391> hw:0,6: modem set state: 9 --> 1...
> > <553.827397> hw:0,6: new state: MODEM_IDLE
> > <553.827417> hw:0,6: modem report result: 3 (NO CARRIER)
> > <553.827435> main: dev write = 0
> >
> > ====================================================
> >
> > The AT command log:
> >
> > cu -l /dev/ttySL0
> > Connected.
> > atz
> > OK
> > atx3
> > OK
> > atdt9008080
> > NO CARRIER
> >
> > ===================================================
> >
> > ModemData.txt:
> >
> >
> > Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List
> > Server,
> > as HTML can contain viruses. Use as the email Subject Line:
> > YourName, YourCountry
> > Welcome to openSUSE 10.3 (i586) - Kernel kernel 2.6.22.13-0.3-default
> > With this Subject Line cogent experts will be alerted, and useful case
> > names left in the Archive.
> > YourCountry will enable Country specific guidance. Your contry's local
> > Linux experts
> > can be found through: http://www.linux.org/groups/index.html
> > Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an
> > Internet Provider mail filters.
> > So in a day, also check the Archived responses at http://www.linmodems.org
> > -------------------------- System information ----------------------------
> > CPU=i686,
> > Welcome to openSUSE 10.3 (i586) - Kernel
> > Linux version 2.6.22.13-0.3-default (geeko@buildhost) (gcc version 4.2.1
> > (SUSE Linux)) #1 SMP 2007/11/19 15:02:58 UTC
> > scanModem update of: 2008_03_01
> >
> >
> > There are no blacklisted modem drivers in /etc/modprobe* files
> > PCI slot 00:1b.0 has a High Definition Audio Card
> >
> > The Advanced Linux Sound Architecture (ALSA) packages providing audio
> > support,
> > also includes drivers for some modems. The ALSA diagnostics are written
> > during
> > bootup to /proc/asound/ folders.
> >
> >
> > The ALSA verion is 1.0.14
> > The modem cards detected by "aplay -l" are:
> > card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem]
> >
> >
> > The /proc/asound/pcm file reports:
> > -----------------------
> > 00-06: Si3054 Modem : Si3054 Modem : playback 1 : capture 1
> > 00-02: ALC883 Analog : ALC883 Analog : capture 2
> > 00-01: ALC883 Digital : ALC883 Digital : playback 1 : capture 1
> > 00-00: ALC883 Analog : ALC883 Analog : playback 1 : capture 2
> >
> > about /proc/asound/cards:
> > ------------------------
> > 0 [Intel ]: HDA-Intel - HDA Intel
> > HDA Intel at 0xfeb38000 irq 16
> >
> > USB modem not detected by lsusb
> >
> > For candidate card in slot 00:1b.0, firmware information and bootup
> > diagnostics are:
> > PCI slot PCI ID SubsystemID Name
> > ---------- --------- --------- --------------
> > 00:1b.0 8086:27d8 1462:0531 Audio device: Intel
> > Corporation 82801G
> >
> > Modem interrupt assignment and sharing:
> > 16: 1908 74131905 IO-APIC-fasteoi uhci_hcd:usb5,
> > sdhci:slot0, ohci1394, HDA Intel, yenta, i915@pci:0000:00:02.0
> > --- Bootup diagnostics for card in PCI slot 00:1b.0 ----
> >
> >
> > === Finished modem firmware and bootup diagnostics section. ===
> > === Next deducing cogent software ===
> >
> >
> >
> >
> > The base of the UDEV device file system is: /dev/.udev
> >
> > Versions adequately match for the compiler installed: 4.2.1
> > and the compiler used in kernel assembly: 4.2.1
> >
> >
> >
> > Minimal compiling resources appear complete:
> > make utility - /usr/bin/make
> > Compiler version 4.2
> > linuc_headers base folder /lib/modules/2.6.22.13-0.3-default/build
> >
> > However some compilations and executable functions may need additional
> > files,
> > in the FileNames.h (so called kernel "h"eaders) collection installed in
> > /usr/include/ .
> > For martian_modem, additional required packages are libc6-dev (and for
> > Debian/Ubuntu, linux-libc-dev). The also required headers of package
> > libc6 are commonly installed by default.
> >
> >
> >
> > If a driver compilation fails, with message including some lack of some
> > FileName.h (stdio.h for example), then
> > Some additional kernel-header files need installation to /usr/include.
> > The minimal additional packages are libc6-dev
> > and any of its dependents, under Ubuntu linux-libc-dev
> >
> > If an alternate ethernet connection is available,
> > $ apt-get update
> > $ apt-get -s install linux-kernel-devel
> > will install needed package
> > For Debian/Ubuntu related distributions, run the following command to
> > display the needed package list:
> >
> > Otherwise packages have to be found through http://packages.ubuntu.com
> > Once downloaded and transferred into a Linux partition,
> > they can be installed alltogether with:
> > $ sudo dpkg -i *.deb
> >
> >
> > Checking pppd properties:
> > -rwxr-xr-x 1 root dialout 298784 2007-09-22 02:41 /usr/sbin/pppd
> >
> > In case of an "error 17" "serial loopback" problem, see:
> > http://phep2.technion.ac.il/linmodems/archive-sixth/msg02637.html
> >
> > To enable dialout without Root permission do:
> > $ su - root (not for Ubuntu)
> > chmod a+x /usr/sbin/pppd
> > or under Ubuntu related Linuxes
> > chmod a+x /usr/sbin/pppd
> >
> > Checking settings of: /etc/ppp/options
> > noipdefault
> > noauth
> > crtscts
> > lock
> > modem
> > asyncmap 0
> > nodetach
> > lcp-echo-interval 30
> > lcp-echo-failure 4
> > lcp-max-configure 60
> > lcp-restart 2
> > idle 600
> > noipx
> > file /etc/ppp/filters
> >
> > In case of a message like:
> > Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
> > see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
> >
> > Read Modem/YourSystem.txt concerning other COMM channels: eth0 eth1
> > vmnet1 vmnet8
> > Which can interfere with Browser naviagation.
> >
> > Don't worry about the following, it is for the experts
> > should trouble shooting be necessary.
> > ==========================================================
> >
> > Checking for modem support lines:
> > --------------------------------------
> > /device/modem symbolic link:
> > slmodemd created symbolic link /dev/ttySL0:
> > Within /etc/udev/ files:
> > /etc/udev/rules.d/50-udev-default.rules:KERNEL=="mwave",
> > NAME="modems/%k", GROUP="uucp"
> > /etc/udev/rules.d/77-network.rules:SUBSYSTEM=="net",
> > ENV{INTERFACE}=="ppp*|ippp*|isdn*|plip*|lo*|irda*|dummy*|ipsec*|tun*|tap*|bond*|vlan*|modem*|dsl*",
> > GOTO="skip_ifup"
> > Within /etc/modprobe.conf files:
> > /etc/modprobe.conf:# Linux ACP modem (Mwave)
> > Within any ancient /etc/devfs files:
> >
> > Within ancient kernel 2.4.n /etc/module.conf files:
> >
> > --------- end modem support lines --------
> >
> >
> >
>
