Many thanks for your reply. I don't know why is not working at all, this is very strange... Now problem is that after #wvdial I get ............. ATDT7020187187 --> Timed out while dialing. Trying again. --> Sending: ATDT7020187187 --> Waiting for carrier. and so on without getting any connection I start from wvdial.conf [Dialer Defaults] Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=34 Modem Type = Analog Modem Phone = 7020187187 ISDN = 0 Username = telecom Password = telecom Modem = /dev/ttySL0 Baud = 460800 #New PPPD = yes Carrier Check = no SetVolume = 1 Stupid mode = yes Auto DNS = yes #Dial Command = ATDT [Dialer 2nd] Username = amosse@xxxxxxxxx Password = bomba Phone = 0571861010 It semms to be OK?, only some questions: Looking on the web I find some examples with Dial Command, is it important to put it? If yes what value? In any case I tried both with and without no changes: Yesterday during my succesfull trial sometimes I did't start slmodemd in the normal way: # slmodemd -c ITALY --alsa modem:1 because I have set up slmodemd in "Editor runlevel" on yes, in this way I think service start automatically, but I don't know if with alsa support... I have to inizialize slmodemd service as above or leave it autoload with runlevel? I try both providers same problem as above said. This is very strange behaviour, what I have to check ...?? Thanks Amos ps: do you have some wvdial.conf tutorial to suggest me in order to understand meaning of the set up. > Amos, > > Good progress!! > Note X3 is in Init2. For Init1 use > Init1 = ATZ > RE: is it right to set up wvdial.conf in this way in order to connect > to 2 different provider? (I try telecom connection dialing # wvdial > 2nd) > -------- > Yes, but you could simplify as, the "wvdial 2nd" will reference the > default, for any missing lines. So if would suffice to use format: > > [Dialer default] > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=90 > # +MS=34 might provide a longer CONNECT > Modem Type = Analog Modem > Phone = 0571861010 > ISDN = 0 > Username = amosse@xxxxxxxxx > Password = zzzzzzzz > Modem = /dev/ttySL0 > Baud = 460800 > Carrier Check = no > SetVolume = 1 > Stupid mode = yes > Auto DNS = yes > > [Dialer 2nd] > Phone = 7020187187 > Username = telecom > Password = telecom > > Read Jacques Post Install HowTo at > > On Dec 25, 2007 12:53 PM, amosse@xxxxxxxxx <amosse@xxxxxxxxx> wrote: > > Got it! > > > > This is a great result for me. > > > > # slmodemd -c ITALY --alsa modem:1 > > SmartLink Soft Modem: version 2.9.11 Nov 21 2007 09:03:10 > > symbolic link `/dev/ttySL0' -> `/dev/pts/3' created. > > modem `modem:1' created. TTY is `/dev/pts/3' > > Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > > > > [Dialer 2nd] > > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=90 > > Modem Type = Analog Modem > > Phone = 7020187187 > > ISDN = 0 > > Username = telecom > > Init1 = ATX3 > > Password = telecom > > Modem = /dev/ttySL0 > > Baud = 460800 > > Carrier Check = no > > SetVolume = 1 > > Stupid mode = yes > > Auto DNS = yes > > > > wvdial 2nd > > --> WvDial: Internet dialer version 1.56 (abuild@balli) > > --> Cannot get information for serial port. > > --> Initializing modem. > > --> Sending: ATX3 > > ATX3 > > OK > > --> Sending: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=90 > > ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=90 > > OK > > --> Modem initialized. > > --> Sending: ATX3DT7020187187 > > --> Waiting for carrier. > > ATX3DT7020187187 > > CONNECT 53333 > > --> Carrier detected. Starting PPP immediately. > > --> Starting pppd at Tue Dec 25 21:39:23 2007 > > --> Pid of pppd: 22386 > > --> Using interface ppp0 > > --> pppd: 8[11][06][08][18][10][06][08] > > --> pppd: 8[11][06][08][18][10][06][08] > > --> pppd: 8[11][06][08][18][10][06][08] > > --> pppd: 8[11][06][08][18][10][06][08] > > --> local IP address 80.104.165.49 > > --> pppd: 8[11][06][08][18][10][06][08] > > --> remote IP address 151.99.26.43 > > --> pppd: 8[11][06][08][18][10][06][08] > > --> primary DNS address 62.211.69.150 > > --> pppd: 8[11][06][08][18][10][06][08] > > --> secondary DNS address 212.48.4.15 > > --> pppd: 8[11][06][08][18][10][06][08] > > --> Script /etc/ppp/ip-up run successful > > --> Default route Ok. > > --> Nameserver (DNS) Ok. > > --> Connected... Press Ctrl-C to disconnect > > --> pppd: 8[11][06][08][18][10][06][08] > > > > Many thanks to everybody > > > > Amos > > > > >
