Hi,
it's me again. Last time i used Fedora Core 7 kernel 2.6.21-1 and your
advice did not help me. scanModem recognized two modem controllers: AC97
modem controller and Agere Systems V.92 56K winmodem controller. You adviced
me to disable one of them but i don't know how. I used "unloading" and
agrsm-20070804 driver but it dosn't help me to start modem.
This time i'm using Ubuntu 7.04 with kernel 2.6.20-15 generic and scanModem
also recognized same two controllers. Also it sagesting me to use
agrsm-alpha.tar.bz2 for Agere and SLMODEMD.gcc4.1.tar.gz for AC97.
Should i install bote drivers?
Maby these controllers are one device?
Should i update kernel to versions i had: 2.6.22.1, 2.6.22.9 or 2.6.23.1?
Can you help me?
Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server,
as HTML can contain viruses. Use as the email Subject Line:
YourName, YourCountry kernel 2.6.20-15-generic
With this Subject Line cogent experts will be alerted, and useful case names left in the Archive.
YourCountry will enable Country specific guidance. Your contry's local Linux experts
can be found through: http://www.linux.org/groups/index.html
Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet Provider mail filters.
So in a day, also check the Archived responses at http://www.linmodems.org
-------------------------- System information ----------------------------
CPU=i686,
Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007
scanModem update of: 2007-20-07
There are no blacklisted modem drivers in /etc/modprobe* files
Potentially useful modem drivers now loaded are:
snd_via82xx_modem
The Advanced Linux Sound Architecture (ALSA) packages providing audio support on your System,
also includes drivers for some modems. High Definition Audio (HDA) cards can themselves host
a softmodem chipset, with both audio+modem supported by a snd-hda-intel driver.
The ALSA diagnostics are written during bootup to /proc/asound/ folders.
Modem not detected though HDA card diagnostics, though not excluding
a possible Conexant modem chip impervious to ALSA diagnostics.
Proceeding through alternative possibilties.
Summary card and chipset information is in:
/proc/asound/cards:
0 [V8237 ]: VIA8237 - VIA 8237
VIA 8237 with AD1980 at 0xe000, irq 19
/proc/asound/pcm:
00-01: VIA 8237 : VIA 8237 : playback 1 : capture 1
00-00: VIA 8237 : VIA 8237 : playback 4 : capture 1
A copy of /proc/asound had been copied to Modem/ALSAroot.tgz
USB modem not detected by lsusb
For candidate card, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:0d.0 11c1:048c 11c1:044c Communication controller: Agere Systems V.92 56K WinModem
Modem interrupt assignment and sharing:
--- Bootup diagnostics for card in PCI slot 00:0d.0 ----
For candidate card, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:11.6 1106:3068 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller
Modem interrupt assignment and sharing:
19: 216922 IO-APIC-fasteoi VIA8237
--- Bootup diagnostics for card in PCI slot 00:11.6 ----
[ 39.617767] PCI: Enabling device 0000:00:11.6 (0000 -> 0001)
[ 39.617776] ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 19
[ 40.371429] PCI: Setting latency timer of device 0000:00:11.6 to 64
[ 40.874764] ACPI: PCI interrupt for device 0000:00:11.6 disabled
[ 40.874776] VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13
The PCI slot 00:11.6 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
=== Finished modem firmware and bootup diagnostics section. ===
=== Next deducing cogent software ===
PCIbus=00:11.6
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
Flags: medium devsel, IRQ 19
I/O ports at 1000 [size=256]
Capabilities: [d0] Power Management version 2
There is candidate modem software.
For candidate modem in PCI bus: 00:0d.0
Class 0780: 11c1:048c Communication controller: Agere Systems V.92 56K WinModem
Primary PCI_id 11c1:048c
Support type needed or chipset: Agere.SV2P
Already loaded into the kernel is snd-via82xx-modem and audio drivers it depends on,
displayed by: lsmod | grep snd_via82xx_modem
Module Size Used by
-------------------------------------
snd_via82xx_modem 16008 0
snd_ac97_codec 98336 2 snd_via82xx_modem,snd_via82xx
snd_pcm 79876 6 snd_via82xx_modem,snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd 54020 20 snd_via82xx_modem,snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
snd_page_alloc 10888 3 snd_via82xx_modem,snd_via82xx,snd_pcm
Vendor 11c1 is Lucent Technologies with modem technology now under LSI Inc.
Their Linux code developer/maintainer is Soumyendu Sarkar. Support for a chipset and its
continued maintenance is only initiated at the request of a major chipset buyer,
or comparable sponsor. Several different modem chipset types are produced:
with varying support under Linux.
Device ID Support Name Comment
--------- ------------- ----------- -----------------------------
0480 serial drivers Venus controller chipset 1673JV7
0440-045d martian Mars/Apollo DSP (digital signal processing) chipsets
0462 none 56K.V90/ADSL Wildwire
048d none SV2P soft modem
048(c or f) AGRSM SV2P soft modem
0600 none soft modem, very few in the field.
0620 AGRSM Pinball soft modem, in some HP desktop PCs
062(1-3) none SV92PP,Pinball soft modem, in some HP desktop PCs
martian - At http://phep2.technion.ac.il/linmodems/packages/ltmodem/kernel-2.6/martian/
AGRSM - At http://phep2.technion.ac.il/linmodems/packages/ltmodem/sv92/ Read Agrsm.txt
Read Agrsm.txt
-------------- end Agere Systems section -------------------
For candidate modem in PCI bus: 00:11.6
Class 0780: 1106:3068 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller
Primary PCI_id 1106:3068
Subsystem PCI_id none
Softmodem codec or chipset from diagnostics:
from Archives:
Lacking a dsp (digital signal processing) chip, the modem is a software
intensive or "softmodem" type. Its primary controller manages the traffic
with the CPU. But the software needed is specified in the Subsystem.
-----------------------------------------
Support type needed or chipset:
Support can likely be achieved through two mutually exclusive alternatives:
1) The hsfmodem software for Conexant chipset modems: Read Conexant.txt
The following ALSA alternative CANNOT work with Conexant modems.
2) An ALSA modem driver plus slmodemd. Read Smartlink.txt for details, and
to test get the package SLMODEMD.gcc4.1.tar.gz from:
http://linmodems.technion.ac.il/packages/smartlink/
Already loaded into the kernel is snd-via82xx-modem and audio drivers it depends on,
displayed by: lsmod | grep snd_via82xx_modem
Module Size Used by
-------------------------------------
snd_via82xx_modem 16008 0
snd_ac97_codec 98336 2 snd_via82xx_modem,snd_via82xx
snd_pcm 79876 6 snd_via82xx_modem,snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd 54020 20 snd_via82xx_modem,snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
snd_page_alloc 10888 3 snd_via82xx_modem,snd_via82xx,snd_pcm
scanModem could not identify the Support Type needed from diagnosics or archives.
If an alternative boot into Microsoft windows can be done, do mouse
clicks on:
Start > Settings > Control Panel > Classical View (for Window XP) > System
Hardware > Device Manager > Modems > Click on the + > Modem. Double click to
expand the graphic. Manufacturer information may be displayed. For example, CXT
stands for Conexant. Click the Diagnostics Tab. Record any hardware ID or vendor
and device information.
Next do the Query Modem and record the ATI specifications displayed such as:
ATI3 - Agere SoftModem Version 2.1.22
ATI5 - 2.1.22, AMR Intel MB, AC97 ID:SIL REV:0x27
Try to identify the modem setup file, with name perhaps MODEM.INF.
If may contain chipset Vendor informaton.
Writing Smartlink.txt
============ end Smartlink section =====================
Completed candidate modem analyses.
The base of the UDEV device file system is: /dev/.udev
Versions adequately match for the compiler installed: 4.1.2
and the compiler used in kernel assembly: 4.1.2
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.1
linuc_headers base folder /lib/modules/2.6.20-15-generic/build
However some compilations and executable functions may need additional files,
in the FileNames.h (so called kernel "h"eaders) collection installed in /usr/include/ .
For martian_modem, additional required packages are libc6-dev (and for Debian/Ubuntu, linux-libc-dev). The also required headers of package libc6 are commonly installed by default.
If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed pacakage
For Debian/Ubuntu related distributions, run the following command to display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwsr-xr-- 1 root dip 269224 2007-04-04 23:41 /usr/sbin/pppd
In case of an "error 17" "serial loopback" problem, see:
http://phep2.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
sudo chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
Read Modem/YourSystem.txt concerning other COMM channels: eth0
Which can interfere with Browser naviagation.
Don't worry about the following, it is for the experts
should trouble shooting be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
Within /etc/modprobe.conf files:
/etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem
/etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
--------- end modem support lines --------
CPU0
0: 225517 IO-APIC-edge timer
1: 607 IO-APIC-edge i8042
7: 0 IO-APIC-edge parport0
8: 3 IO-APIC-edge rtc
9: 0 IO-APIC-fasteoi acpi
12: 98490 IO-APIC-edge i8042
14: 31739 IO-APIC-edge ide0
16: 0 IO-APIC-fasteoi libata
17: 0 IO-APIC-fasteoi uhci_hcd:usb1, uhci_hcd:usb2, uhci_hcd:usb3, uhci_hcd:usb4, ehci_hcd:usb5
18: 0 IO-APIC-fasteoi eth0
19: 216956 IO-APIC-fasteoi VIA8237
NMI: 0
LOC: 225396
ERR: 0
MIS: 0
[ 0.000000] Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007 (Ubuntu 2.6.20-15.27-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001fe30000 end: 000000001ff30000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000001ff30000 size: 0000000000010000 end: 000000001ff40000 type: 3
[ 0.000000] copy_e820_map() start: 000000001ff40000 size: 00000000000b0000 end: 000000001fff0000 type: 4
[ 0.000000] copy_e820_map() start: 000000001fff0000 size: 0000000000010000 end: 0000000020000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000ff7c0000 size: 0000000000840000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001ff30000 (usable)
[ 0.000000] BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 130864) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 130864
[ 0.000000] HighMem 130864 -> 130864
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 130864
[ 0.000000] On node 0 totalpages: 130864
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 990 pages used for memmap
[ 0.000000] Normal zone: 125778 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 ACPIAM ) @ 0x000fa3a0
[ 0.000000] ACPI: RSDT (v001 A M I OEMRSDT 0x08000412 MSFT 0x00000097) @ 0x1ff30000
[ 0.000000] ACPI: FADT (v002 A M I OEMFACP 0x08000412 MSFT 0x00000097) @ 0x1ff30200
[ 0.000000] ACPI: MADT (v001 A M I OEMAPIC 0x08000412 MSFT 0x00000097) @ 0x1ff30390
[ 0.000000] ACPI: OEMB (v001 A M I AMI_OEM 0x08000412 MSFT 0x00000097) @ 0x1ff40040
[ 0.000000] ACPI: DSDT (v001 A0017 A0017001 0x00000001 INTL 0x02002026) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:2 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:df7c0000)
[ 0.000000] Detected 2266.678 MHz processor.
[ 18.508330] Built 1 zonelists. Total pages: 129842
[ 18.508335] Kernel command line: root=UUID=945dd529-95af-4345-8546-e940f6c75c88 ro quiet splash
[ 18.508526] mapped APIC to ffffd000 (fee00000)
[ 18.508529] mapped IOAPIC to ffffc000 (fec00000)
[ 18.508533] Enabling fast FPU save and restore... done.
[ 18.508536] Enabling unmasked SIMD FPU exception support... done.
[ 18.508551] Initializing CPU#0
[ 18.508668] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 18.510095] Console: colour VGA+ 80x25
[ 18.510471] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 18.510793] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 18.522463] Memory: 507200k/523456k available (1992k kernel code, 15684k reserved, 893k data, 328k init, 0k highmem)
[ 18.522476] virtual kernel memory layout:
[ 18.522477] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 18.522478] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 18.522480] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 18.522481] lowmem : 0xc0000000 - 0xdff30000 ( 511 MB)
[ 18.522482] .init : 0xc03d7000 - 0xc0429000 ( 328 kB)
[ 18.522484] .data : 0xc02f2264 - 0xc03d16d4 ( 893 kB)
[ 18.522485] .text : 0xc0100000 - 0xc02f2264 (1992 kB)
[ 18.522489] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 18.600525] Calibrating delay using timer specific routine.. 4539.74 BogoMIPS (lpj=9079485)
[ 18.600576] Security Framework v1.0.0 initialized
[ 18.600585] SELinux: Disabled at boot.
[ 18.600606] Mount-cache hash table entries: 512
[ 18.600786] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[ 18.600801] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 18.600804] CPU: L2 cache: 512K
[ 18.600807] CPU: Hyper-Threading is disabled
[ 18.600810] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400 00000000 00000000
[ 18.600823] Compat vDSO mapped to ffffe000.
[ 18.600827] Remapping vsyscall page to ffffe000
[ 18.600842] Checking 'hlt' instruction... OK.
[ 18.616612] SMP alternatives: switching to UP code
[ 18.616835] Freeing SMP alternatives: 11k freed
[ 18.617086] Early unpacking initramfs... done
[ 18.985946] ACPI: Core revision 20060707
[ 18.986165] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 18.988465] CPU0: Intel(R) Pentium(R) 4 CPU 2.26GHz stepping 09
[ 18.988519] Total of 1 processors activated (4539.74 BogoMIPS).
[ 18.989277] ENABLING IO-APIC IRQs
[ 18.989616] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 19.135688] Brought up 1 CPUs
[ 19.136033] Booting paravirtualized kernel on bare hardware
[ 19.136151] Time: 1:41:45 Date: 11/20/107
[ 19.136187] NET: Registered protocol family 16
[ 19.136307] EISA bus registered
[ 19.136313] ACPI: bus type pci registered
[ 19.136408] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
[ 19.136410] PCI: Using configuration type 1
[ 19.136413] Setting up standard PCI resources
[ 19.152983] ACPI: Interpreter enabled
[ 19.152988] ACPI: Using IOAPIC for interrupt routing
[ 19.154370] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 19.154380] PCI: Probing PCI hardware (bus 00)
[ 19.155199] PCI: enabled onboard AC97/MC97 devices
[ 19.155492] Boot video device is 0000:01:00.0
[ 19.155553] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 19.168923] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 19.169190] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
[ 19.169452] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 19.169714] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 19.169984] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 19.170246] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 19.170515] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 19.170779] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 19.170923] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 19.170938] pnp: PnP ACPI init
[ 19.175525] pnp: PnP ACPI: found 13 devices
[ 19.175532] PnPBIOS: Disabled by ACPI PNP
[ 19.175652] PCI: Using ACPI for IRQ routing
[ 19.175657] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 19.178905] NET: Registered protocol family 8
[ 19.178907] NET: Registered protocol family 20
[ 19.179790] pnp: 00:0b: ioport range 0x680-0x6ff has been reserved
[ 19.180156] PCI: Bridge: 0000:00:01.0
[ 19.180159] IO window: disabled.
[ 19.180164] MEM window: dd700000-df8fffff
[ 19.180169] PREFETCH window: cd600000-dd5fffff
[ 19.180191] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 19.180227] NET: Registered protocol family 2
[ 19.219588] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 19.219687] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 19.219786] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 19.219837] TCP: Hash tables configured (established 16384 bind 8192)
[ 19.219840] TCP reno registered
[ 19.231621] checking if image is initramfs... it is
[ 19.968257] Freeing initrd memory: 7499k freed
[ 19.968800] audit: initializing netlink socket (disabled)
[ 19.968819] audit(1198114905.540:1): initialized
[ 19.968992] VFS: Disk quotas dquot_6.5.1
[ 19.969017] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 19.969079] io scheduler noop registered
[ 19.969083] io scheduler anticipatory registered
[ 19.969086] io scheduler deadline registered
[ 19.969095] io scheduler cfq registered (default)
[ 19.969178] PCI: Bypassing VIA 8237 APIC De-Assert Message
[ 19.969456] isapnp: Scanning for PnP cards...
[ 20.323365] isapnp: No Plug & Play device found
[ 20.357022] Real Time Clock Driver v1.12ac
[ 20.357089] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 20.357221] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 20.358264] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 20.358634] mice: PS/2 mouse device common for all mice
[ 20.359334] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 20.359659] input: Macintosh mouse button emulation as /class/input/input0
[ 20.359705] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 20.359711] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 20.360024] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 20.362927] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 20.362934] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 20.363105] EISA: Probing bus 0 at eisa.0
[ 20.363116] Cannot allocate resource for EISA slot 1
[ 20.363146] EISA: Detected 0 cards.
[ 20.393229] TCP cubic registered
[ 20.393236] NET: Registered protocol family 1
[ 20.393267] Using IPI No-Shortcut mode
[ 20.393349] ACPI: (supports S0 S1 S3 S4 S5)
[ 20.393404] Magic number: 3:774:660
[ 20.393518] hash matches device ptyeb
[ 20.393527] Time: tsc clocksource has been installed.
[ 20.394036] Freeing unused kernel memory: 328k freed
[ 20.407045] input: AT Translated Set 2 keyboard as /class/input/input1
[ 21.655443] Capability LSM initialized
[ 21.675567] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx
[ 21.712550] ACPI: Processor [CPU1] (supports 16 throttling states)
[ 21.712565] ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
[ 21.819863] md: linear personality registered for level -1
[ 21.824305] md: multipath personality registered for level -4
[ 21.828552] md: raid0 personality registered for level 0
[ 21.833413] md: raid1 personality registered for level 1
[ 21.837560] raid5: automatically using best checksumming function: pIII_sse
[ 21.855084] pIII_sse : 2866.000 MB/sec
[ 21.855087] raid5: using function: pIII_sse (2866.000 MB/sec)
[ 21.926965] raid6: int32x1 643 MB/s
[ 21.994915] raid6: int32x2 622 MB/s
[ 22.062746] raid6: int32x4 637 MB/s
[ 22.130634] raid6: int32x8 424 MB/s
[ 22.198538] raid6: mmxx1 1732 MB/s
[ 22.266404] raid6: mmxx2 2322 MB/s
[ 22.334329] raid6: sse1x1 1087 MB/s
[ 22.402189] raid6: sse1x2 2045 MB/s
[ 22.470065] raid6: sse2x1 1669 MB/s
[ 22.537947] raid6: sse2x2 2561 MB/s
[ 22.537949] raid6: using algorithm sse2x2 (2561 MB/s)
[ 22.537954] md: raid6 personality registered for level 6
[ 22.537956] md: raid5 personality registered for level 5
[ 22.537958] md: raid4 personality registered for level 4
[ 22.580723] md: raid10 personality registered for level 10
[ 23.061852] SCSI subsystem initialized
[ 23.068352] libata version 2.20 loaded.
[ 23.070141] sata_via 0000:00:0f.0: version 2.1
[ 23.070172] ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 16
[ 23.070196] sata_via 0000:00:0f.0: routed to hard irq line 10
[ 23.070268] ata1: SATA max UDMA/133 cmd 0x0001efe0 ctl 0x0001efae bmdma 0x0001ef90 irq 16
[ 23.070301] ata2: SATA max UDMA/133 cmd 0x0001efa0 ctl 0x0001efaa bmdma 0x0001ef98 irq 16
[ 23.070319] scsi0 : sata_via
[ 23.095295] usbcore: registered new interface driver usbfs
[ 23.095326] usbcore: registered new interface driver hub
[ 23.095358] usbcore: registered new device driver usb
[ 23.096522] USB Universal Host Controller Interface driver v3.0
[ 23.193545] via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
[ 23.276631] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 23.287306] ATA: abnormal status 0x7F on port 0x0001efe7
[ 23.287402] scsi1 : sata_via
[ 23.492215] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 23.502920] ATA: abnormal status 0x7F on port 0x0001efa7
[ 23.505410] VP_IDE: IDE controller at PCI slot 0000:00:0f.1
[ 23.505434] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 16
[ 23.505448] VP_IDE: chipset revision 6
[ 23.505451] VP_IDE: not 100% native mode: will probe irqs later
[ 23.505464] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
[ 23.505473] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
[ 23.505488] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
[ 23.505496] Probing IDE interface ide0...
[ 23.931557] hda: Maxtor 6Y080L0, ATA DISK drive
[ 24.382787] hdb: PIONEER DVD-RW DVR-112D, ATAPI CD/DVD-ROM drive
[ 24.439313] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 24.456378] Probing IDE interface ide1...
[ 25.031211] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17
[ 25.031229] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 25.031563] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 25.031604] uhci_hcd 0000:00:10.0: irq 17, io base 0x0000eec0
[ 25.032235] usb usb1: configuration #1 chosen from 1 choice
[ 25.032459] hub 1-0:1.0: USB hub found
[ 25.032474] hub 1-0:1.0: 2 ports detected
[ 25.040914] hda: max request size: 128KiB
[ 25.054663] hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63
[ 25.054836] hda: cache flushes supported
[ 25.054892] hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
[ 25.133625] hdb: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)
[ 25.133639] Uniform CD-ROM driver Revision: 3.20
[ 25.137620] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17
[ 25.137637] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 25.137671] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 25.137696] uhci_hcd 0000:00:10.1: irq 17, io base 0x0000ef00
[ 25.137805] usb usb2: configuration #1 chosen from 1 choice
[ 25.137838] hub 2-0:1.0: USB hub found
[ 25.137847] hub 2-0:1.0: 2 ports detected
[ 25.245513] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 17
[ 25.245531] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 25.245568] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 25.245595] uhci_hcd 0000:00:10.2: irq 17, io base 0x0000ef20
[ 25.245708] usb usb3: configuration #1 chosen from 1 choice
[ 25.245741] hub 3-0:1.0: USB hub found
[ 25.245752] hub 3-0:1.0: 2 ports detected
[ 25.353205] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 17
[ 25.353224] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 25.353260] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 25.353286] uhci_hcd 0000:00:10.3: irq 17, io base 0x0000ef40
[ 25.353402] usb usb4: configuration #1 chosen from 1 choice
[ 25.353433] hub 4-0:1.0: USB hub found
[ 25.353444] hub 4-0:1.0: 2 ports detected
[ 25.461168] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 18
[ 25.461276] eth0: VIA Rhine II at 0x1e400, 00:11:2f:da:c6:52, IRQ 18.
[ 25.461993] eth0: MII PHY found at address 1, status 0x7849 advertising 01e1 Link 0000.
[ 25.462100] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17
[ 25.462112] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 25.462144] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 25.462188] ehci_hcd 0000:00:10.4: irq 17, io mem 0xdfe00000
[ 25.462196] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 25.462292] usb usb5: configuration #1 chosen from 1 choice
[ 25.462326] hub 5-0:1.0: USB hub found
[ 25.462335] hub 5-0:1.0: 8 ports detected
[ 25.599898] Attempting manual resume
[ 25.599903] swsusp: Resume From Partition 3:7
[ 25.599906] PM: Checking swsusp image.
[ 25.610851] PM: Resume from disk failed.
[ 25.645467] kjournald starting. Commit interval 5 seconds
[ 25.645483] EXT3-fs: mounted filesystem with ordered data mode.
[ 38.034415] Linux agpgart interface v0.102 (c) Dave Jones
[ 38.350661] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 38.354437] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 38.708049] agpgart: Detected VIA PT800 chipset
[ 38.712188] agpgart: AGP aperture is 64M @ 0xe0000000
[ 38.716507] input: PC Speaker as /class/input/input2
[ 38.824723] parport: PnPBIOS parport detected.
[ 38.824838] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 39.068162] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 19
[ 39.068314] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 39.482282] input: ImPS/2 Generic Wheel Mouse as /class/input/input3
[ 39.584068] codec_read: codec 0 is not valid [0x107e5370]
[ 39.591159] codec_read: codec 0 is not valid [0x107e5370]
[ 39.598292] codec_read: codec 0 is not valid [0x107e5370]
[ 39.605378] codec_read: codec 0 is not valid [0x107e5370]
[ 39.617767] PCI: Enabling device 0000:00:11.6 (0000 -> 0001)
[ 39.617776] ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 19
[ 40.371429] PCI: Setting latency timer of device 0000:00:11.6 to 64
[ 40.874764] ACPI: PCI interrupt for device 0000:00:11.6 disabled
[ 40.874776] VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13
[ 41.018158] lp0: using parport0 (interrupt-driven).
[ 41.055437] Adding 1044184k swap on /dev/disk/by-uuid/89cd4659-2edf-498b-be9c-016eb34af876. Priority:-1 extents:1 across:1044184k
[ 41.228612] EXT3 FS on hda6, internal journal
[ 43.388868] fuse init (API version 7.8)
[ 45.828159] input: Power Button (FF) as /class/input/input4
[ 45.833488] ACPI: Power Button (FF) [PWRF]
[ 45.868461] input: Power Button (CM) as /class/input/input5
[ 45.873707] ACPI: Power Button (CM) [PWRB]
[ 45.908548] input: Sleep Button (CM) as /class/input/input6
[ 45.913839] ACPI: Sleep Button (CM) [SLPB]
[ 45.930158] Using specific hotkey driver
[ 46.021018] ibm_acpi: ec object not found
[ 46.046806] No dock devices found.
[ 46.153383] pcc_acpi: loading...
[ 50.045716] eth0: link down
[ 63.279404] ppdev: user-space parallel port driver
[ 64.084443] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 64.084450] apm: overridden by ACPI.
[ 64.302760] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 64.425082] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 64.438530] NFSD: starting 90-second grace period
[ 66.683333] NET: Registered protocol family 10
[ 66.683454] lo: Disabled Privacy Extensions
[ 66.683520] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 67.282088] Bluetooth: Core ver 2.11
[ 67.282543] NET: Registered protocol family 31
[ 67.282547] Bluetooth: HCI device and connection manager initialized
[ 67.282552] Bluetooth: HCI socket layer initialized
[ 67.344026] Bluetooth: L2CAP ver 2.8
[ 67.344032] Bluetooth: L2CAP socket layer initialized
[ 67.506687] Bluetooth: RFCOMM socket layer initialized
[ 67.506706] Bluetooth: RFCOMM TTY layer initialized
[ 67.506709] Bluetooth: RFCOMM ver 1.8
