Marvin, Firas
Thank you for your help.
I've installed the slamr-2.6.22-14-generic.tar.gz compiled by Firas and driver seems to be working now.
Also I tried to compile by myself folowing Marvin's instructions and DriverCompiling.txt but got some errors in a preparation stage ("make bzImage"), anyway it doesn't matter now.
There is another problem with connecting.
When I'am trying to connect by "sudo wvdial" I get this:
ferat@ferat-desktop:~$ sudo wvdial
[sudo] password for ferat:
WvDial<*1>: WvDial: Internet dialer version 1.56
WvModem<*1>: Cannot get information for serial port.
WvDial<*1>: Initializing modem.
WvDial<*1>: Sending: ATZ
WvDial Modem<*1>: ATZ
WvDial Modem<*1>: OK
WvDial<*1>: Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
WvDial Modem<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
WvDial Modem<*1>: OK
WvDial<*1>: Modem initialized.
WvDial<*1>: Sending: ATDTp1739199
WvDial<*1>: Waiting for carrier.
WvDial Modem<*1>: ATDTp1739199
WvDial Modem<*1>: CONNECT 42667
WvDial Modem<*1>: User Access Verification
WvDial Modem<*1>: Username:
WvDial<*1>: Carrier detected. Waiting for prompt.
WvDial Modem<*1>: NO CARRIER
WvDial<Notice>: Don't know what to do! Starting pppd and hoping for the best.
WvDial<Notice>: Starting pppd at Mon Dec 10 17:23:15 2007
WvDial<Notice>: Pid of pppd: 6853
WvDial<*1>: Using interface ppp0
WvDial<*1>: pppd: [10]п [06][08]п п [06][08]
WvDial<*1>: pppd: [10]п [06][08]п п [06][08]
This is my wvdial.conf:
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Baud = 460800
New PPPD = yes
Modem = /dev/ttySL0
ISDN = 0
Phone = p1739199
Password = test
Username = test
Carrier check = no
I tried to change dialup information and connect to several ISP's but didn't get connection with none of them
There is no problems with modem in Windows.
(maybe it will be useful - modem's utility usually displays V.44 protocol)
-----Original Message-----
Here goes : ftp://itsuki.fkraiem.org/pub/slamr-2.6.22-14-generic.tar.gz
Firas
P.S. : For compiling on Ubuntu 7.10, the ungrab-winmodem_20070426.tar.gz
source archive didn't work. I used the ungrab-winmodem_20070430.tar.gz.
-----Original Message-----
Folks
Would someone using Ubuntu and compiling proficient fix my package per
issue below.
> > From .http://linmodems.technion.ac.il/packages/smartlink/Ubuntu/
> > get the slamr-2.6.22-14-generic.tar.gz with compiled drivers.
Ferat
Apologies, I forgot to add the ungrab-winmodem into the slamr package
and am traveling for 10 days more without Linux tools
>From http://linmodems.technion.ac.il/packages/smartlink/ get the package
ungrab-winmodem_20070426.tar.gz
Under Linux do
$ tar zxf ungrab*.tar.gz
to unpack it
$ ls
Will show the unpacked folder. Move in
$ cd ungrab-winmodem_20070426
$ ls
$ make clean
$ make
will compile the driver, Install with
$ sudo make install
This will compensate. Just again in the slamr folder, run the
$ sudo ./setup
There will still be warning messages. But all needed will be properly installed
After the install, an edit will be needed in file
/etc/default/sl-modem-daemon (or similar name)
$ sudo gedit /etc/default/sl-modem-daemon
Just change the country setting to RUSSIA, from USA
During the setup, there should have been generated a file
/etc/wvdial.conf , also needing an edit
$ sudo gedit /etc/wvdial.conf
Remove the ; < > symbols and put in your dialout information.
There should already be a last line:
Carrier Check = no
but add it if necessary.
Save
Do
$ sudo cp /etc/wvdial.conf /etc/wvdial.conf .backup
because if the setup is run again, it will overwrite /etc/wvdial.conf
But a 2nd usage of ./setup should not be done
Reboot and the modem should be ready to use, with
$ sudo wvdial
MarvS
