Bob, e100 is your ethernet driver. So in /etc/modprobe.d/blacklist add a line blacklist e100 this should stop the set of eth0. Check with ifconfig after a subsequent boot. Also you can do $ sudo ifconfig eth0 down $ sudo modprobe -r e100 Re: what a "useless driver" is; The ALSA modem drivers, which cannot support the Smartlink hardware. Just blacklist them by removing the leading # on the blacklist lines. Your outstanding problem is: [ 11.542346] ACPI: PCI interrupt for device 0000:02:0a.0 disabled NOTHING else can work until this problems is solved. The CPU is simple NOT accessing the hardware. wvdial is only getting responses from the slamr driver, and not yet the Smartlink modem hardware. Try the options in Bootup txt. After each subsequent bootup, just check for effectiveness with: $ dmesg | grep 02:0a.0 MarvS On 11/5/07, Jacques Goldberg <Jacques.Goldberg@xxxxxxx> wrote: > Bob, Please clearly positively confirm that you have been using wvdial > and not Kppp or the Gnome equivalent to try to dial, and that slmodemd > was running in an other window at the instant when you launched wvdial > from a command line? > Can you please tell us what you see on your screen in the window when > you start slmodemd ? > > Thanks. Regards. > > Jacques > > Bob Terrell wrote: > > > MY ACTIONS AND DEBUG: > > I guessed and blacklisted ipv6, but eth0 still > > comes uP. I am running kubuntu, so use KPPP instead of > > Gnome-ppp. I can use either one, and can do so on a > > system with any distro of Ubuntu you would like. I > > have one sitting here with Edubuntu and Gnome-ppp I > > can use if you request. Both KPPP and wvdial produce > > the same disconnect, and both still leave the phone > > line and carrier active. KPPP does not give me a > > disconnect message, wvdial does. wvdial leaves the > > phone line and carrier active after presenting the > > DISCONNECT message. > > > > LISTED BELOW: > > "cat /etc/wvdial.conf"; > > "sudo wvdial 2>1 _ tee wvlog.txt"; > > "cat wvlog.txt", > > "cat /etc/modprobe.d/blacklist"; > > "cat /etc/modprobe.d/blacklist-modem" NOTE I have > > added nothing to this, do not understand what a > > "useless driver" is; > > "lsmod"; > > "lspci | grep -v bridge"; > > "lspci | grep -v USB"; > > "lspci | grep -v RAM"; > > "cat dmesg.txt" > > > > Anything else you need, let me know. > > Bob Terrell > > > > ------------------------------------------ > > user1@kubuntu704:~$ cat /etc/wvdial.conf > > > > [Dialer Defaults] > > Init1 = ATZ > > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > Modem Type = Analog Modem > > ISDN = 0 > > New PPPD = yes > > Phone = 6875000 > > Modem = /dev/ttySL0 > > Username = acooper > > Password = acooper > > Carrier Check = no > > Baud = 460800 > > > > --------------------------------------------------------- > > user1@kubuntu704:~$ sudo wvdial 2>&1 | tee wvlog.txt > > Password: > > --> WvDial: Internet dialer version 1.56 > > --> Cannot get information for serial port. > > --> Initializing modem. > > --> Sending: ATZ > > ATZ > > OK > > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > OK > > --> Modem initialized. > > --> Sending: ATDT6875000 > > --> Waiting for carrier. > > ATDT6875000 > > --> Disconnecting at Sun Nov 4 14:18:05 2007 > > user1@kubuntu704:~ > > > > ------------------------------------------------------ > > user1@kubuntu704:~$ cat wvlog.txt > > --> WvDial: Internet dialer version 1.56 > > --> Cannot get information for serial port. > > --> Initializing modem. > > --> Sending: ATZ > > ATZ > > OK > > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > OK > > --> Modem initialized. > > --> Sending: ATDT6875000 > > --> Waiting for carrier. > > ATDT6875000 > > --> Disconnecting at Sun Nov 4 14:18:05 2007 > > user1@kubuntu704:~$ > > > > > > > > --------------------------------------------------- > > user1@kubuntu704:~$ lspci | grep -v bridge > > 00:1f.1 IDE interface: Intel Corporation 82801BA IDE > > U100 (rev 05) > > 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM > > USB (Hub #1) (rev 05) > > 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus > > (rev 05) > > 00:1f.4 USB Controller: Intel Corporation 82801BA/BAM > > USB (Hub #2) (rev 05) > > 00:1f.5 Multimedia audio controller: Intel Corporation > > 82801BA/BAM AC'97 Audio (rev 05) > > 01:00.0 VGA compatible controller: ATI Technologies > > Inc Rage 128 PF/PRO AGP 4x TMDS > > 02:08.0 Ethernet controller: Intel Corporation > > 82801BA/BAM/CA/CAM Ethernet Controller (rev 03) > > 02:0a.0 Modem: Smart Link Ltd. Unknown device 2800 > > (rev 02) > > user1@kubuntu704:~$ > > > > > > > > ----------------------------------------------------------- > > user1@kubuntu704:~$ lspci | grep -v USB > > 00:00.0 Host bridge: Intel Corporation 82845 845 > > (Brookdale) Chipset Host Bridge (rev 04) > > 00:01.0 PCI bridge: Intel Corporation 82845 845 > > (Brookdale) Chipset AGP Bridge (rev 04) > > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge > > (rev 05) > > 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA > > Bridge (LPC) (rev 05) > > 00:1f.1 IDE interface: Intel Corporation 82801BA IDE > > U100 (rev 05) > > 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus > > (rev 05) > > 00:1f.5 Multimedia audio controller: Intel Corporation > > 82801BA/BAM AC'97 Audio (rev 05) > > 01:00.0 VGA compatible controller: ATI Technologies > > Inc Rage 128 PF/PRO AGP 4x TMDS > > 02:08.0 Ethernet controller: Intel Corporation > > 82801BA/BAM/CA/CAM Ethernet Controller (rev 03) > > 02:0a.0 Modem: Smart Link Ltd. Unknown device 2800 > > (rev 02) > > user1@kubuntu704:~$ > > > > > > > > ------------------------------------------------------------ > > user1@kubuntu704:~$ lspci | grep -v RAM > > 00:00.0 Host bridge: Intel Corporation 82845 845 > > (Brookdale) Chipset Host Bridge (rev 04) > > 00:01.0 PCI bridge: Intel Corporation 82845 845 > > (Brookdale) Chipset AGP Bridge (rev 04) > > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge > > (rev 05) > > 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA > > Bridge (LPC) (rev 05) > > 00:1f.1 IDE interface: Intel Corporation 82801BA IDE > > U100 (rev 05) > > 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM > > USB (Hub #1) (rev 05) > > 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus > > (rev 05) > > 00:1f.4 USB Controller: Intel Corporation 82801BA/BAM > > USB (Hub #2) (rev 05) > > 00:1f.5 Multimedia audio controller: Intel Corporation > > 82801BA/BAM AC'97 Audio (rev 05) > > 01:00.0 VGA compatible controller: ATI Technologies > > Inc Rage 128 PF/PRO AGP 4x TMDS > > 02:08.0 Ethernet controller: Intel Corporation > > 82801BA/BAM/CA/CAM Ethernet Controller (rev 03) > > 02:0a.0 Modem: Smart Link Ltd. Unknown device 2800 > > (rev 02) > > user1@kubuntu704:~$ > > > > > > > > > > --------------------------------------------------------- > > user1@kubuntu704:~$ lsmod > > Module Size Used by > > r128 40832 2 > > drm 81044 3 r128 > > rfcomm 40856 0 > > l2cap 25856 5 rfcomm > > bluetooth 55908 4 rfcomm,l2cap > > ppdev 10116 0 > > speedstep_lib 6148 0 > > cpufreq_userspace 5408 0 > > cpufreq_stats 7360 0 > > cpufreq_powersave 2688 0 > > cpufreq_conservative 8200 0 > > cpufreq_ondemand 9228 0 > > freq_table 5792 2 > > cpufreq_stats,cpufreq_ondemand > > pcc_acpi 13184 0 > > dev_acpi 12292 0 > > tc1100_wmi 8068 0 > > sony_acpi 6284 0 > > button 8720 0 > > sbs 15652 0 > > container 5248 0 > > asus_acpi 17308 0 > > video 16388 0 > > i2c_ec 6016 1 sbs > > i2c_core 22656 1 i2c_ec > > dock 10268 0 > > battery 10756 0 > > ac 6020 0 > > backlight 7040 1 asus_acpi > > af_packet 23816 2 > > lp 12452 0 > > snd_intel8x0 34332 2 > > snd_ac97_codec 98464 1 snd_intel8x0 > > ac97_bus 3200 1 snd_ac97_codec > > snd_pcm_oss 44544 0 > > snd_mixer_oss 17408 1 snd_pcm_oss > > snd_pcm 79876 3 > > snd_intel8x0,snd_ac97_codec,snd_pcm_oss > > snd_seq_dummy 4740 0 > > snd_seq_oss 32896 0 > > snd_seq_midi 9600 0 > > snd_rawmidi 25472 1 snd_seq_midi > > snd_seq_midi_event 8448 2 > > snd_seq_oss,snd_seq_midi > > snd_seq 52592 6 > > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event > > snd_timer 23684 2 snd_pcm,snd_seq > > snd_seq_device 9100 5 > > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq > > snd 54020 14 > > snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device > > parport_pc 36388 1 > > parport 36936 3 ppdev,lp,parport_pc > > pcspkr 4224 0 > > slamr 433448 0 > > ungrab_winmodem 3712 0 > > soundcore 8672 1 snd > > snd_page_alloc 10888 2 snd_intel8x0,snd_pcm > > psmouse 38920 0 > > serio_raw 7940 0 > > intel_agp 26140 1 > > agpgart 35400 2 drm,intel_agp > > iTCO_wdt 11812 0 > > iTCO_vendor_support 4868 1 iTCO_wdt > > shpchp 34324 0 > > pci_hotplug 32576 1 shpchp > > evdev 11008 3 > > tsdev 8768 0 > > ext3 133128 1 > > jbd 59816 1 ext3 > > mbcache 9604 1 ext3 > > sg 36252 0 > > sr_mod 17060 0 > > cdrom 37664 1 sr_mod > > sd_mod 23428 3 > > floppy 59524 0 > > e100 36232 0 > > mii 6528 1 e100 > > uhci_hcd 25360 0 > > usbcore 134280 2 uhci_hcd > > ata_piix 15492 2 > > ata_generic 9092 0 > > libata 125720 2 ata_piix,ata_generic > > scsi_mod 142348 4 > > sg,sr_mod,sd_mod,libata > > generic 5124 0 [permanent] > > thermal 14856 0 > > processor 31048 1 thermal > > fan 5636 0 > > fbcon 42656 0 > > tileblit 3584 1 fbcon > > font 9216 1 fbcon > > bitblit 6912 1 fbcon > > softcursor 3200 1 bitblit > > vesafb 9220 0 > > capability 5896 0 > > commoncap 8192 1 capability > > user1@kubuntu704:~$ > > > > > > > > > > > > ----------------------------------------------------------- > > user1@kubuntu704:~$ cat dmesg.txt > > [ 0.000000] Linux version 2.6.20-16-generic > > (root@terranova) (gcc version 4.1.2 (Ubuntu > > 4.1.2-0ubuntu4)) #2 SMP Sun Sep 23 19:50:39 UTC 2007 > > (Ubuntu 2.6.20-16.32-generic) > > [ 0.000000] BIOS-provided physical RAM map: > > [ 0.000000] sanitize start > > [ 0.000000] sanitize end > > [ 0.000000] copy_e820_map() start: 0000000000000000 > > size: 000000000009fc00 end: 000000000009fc00 type: 1 > > [ 0.000000] copy_e820_map() type is E820_RAM > > [ 0.000000] copy_e820_map() start: 000000000009fc00 > > size: 0000000000000400 end: 00000000000a0000 type: 2 > > [ 0.000000] copy_e820_map() start: 00000000000e0000 > > size: 0000000000020000 end: 0000000000100000 type: 2 > > [ 0.000000] copy_e820_map() start: 0000000000100000 > > size: 000000000fec0000 end: 000000000ffc0000 type: 1 > > [ 0.000000] copy_e820_map() type is E820_RAM > > [ 0.000000] copy_e820_map() start: 000000000ffc0000 > > size: 0000000000038000 end: 000000000fff8000 type: 3 > > [ 0.000000] copy_e820_map() start: 000000000fff8000 > > size: 0000000000008000 end: 0000000010000000 type: 4 > > [ 0.000000] copy_e820_map() start: 00000000fec00000 > > size: 0000000000001000 end: 00000000fec01000 type: 2 > > [ 0.000000] copy_e820_map() start: 00000000fee00000 > > size: 0000000000001000 end: 00000000fee01000 type: 2 > > [ 0.000000] copy_e820_map() start: 00000000ffb80000 > > size: 0000000000080000 end: 00000000ffc00000 type: 2 > > [ 0.000000] copy_e820_map() start: 00000000fff00000 > > size: 0000000000100000 end: 0000000100000000 type: 2 > > [ 0.000000] BIOS-e820: 0000000000000000 - > > 000000000009fc00 (usable) > > [ 0.000000] BIOS-e820: 000000000009fc00 - > > 00000000000a0000 (reserved) > > [ 0.000000] BIOS-e820: 00000000000e0000 - > > 0000000000100000 (reserved) > > [ 0.000000] BIOS-e820: 0000000000100000 - > > 000000000ffc0000 (usable) > > [ 0.000000] BIOS-e820: 000000000ffc0000 - > > 000000000fff8000 (ACPI data) > > [ 0.000000] BIOS-e820: 000000000fff8000 - > > 0000000010000000 (ACPI NVS) > > [ 0.000000] BIOS-e820: 00000000fec00000 - > > 00000000fec01000 (reserved) > > [ 0.000000] BIOS-e820: 00000000fee00000 - > > 00000000fee01000 (reserved) > > [ 0.000000] BIOS-e820: 00000000ffb80000 - > > 00000000ffc00000 (reserved) > > [ 0.000000] BIOS-e820: 00000000fff00000 - > > 0000000100000000 (reserved) > > [ 0.000000] 0MB HIGHMEM available. > > [ 0.000000] 255MB LOWMEM available. > > [ 0.000000] Entering add_active_range(0, 0, 65472) > > 0 entries of 256 used > > [ 0.000000] Zone PFN ranges: > > [ 0.000000] DMA 0 -> 4096 > > [ 0.000000] Normal 4096 -> 65472 > > [ 0.000000] HighMem 65472 -> 65472 > > [ 0.000000] early_node_map[1] active PFN ranges > > [ 0.000000] 0: 0 -> 65472 > > [ 0.000000] On node 0 totalpages: 65472 > > [ 0.000000] DMA zone: 32 pages used for memmap > > [ 0.000000] DMA zone: 0 pages reserved > > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > > [ 0.000000] Normal zone: 479 pages used for > > memmap > > [ 0.000000] Normal zone: 60897 pages, LIFO > > batch:15 > > [ 0.000000] HighMem zone: 0 pages used for memmap > > [ 0.000000] DMI 2.3 present. > > [ 0.000000] ACPI: RSDP (v000 AMI > > ) @ 0x000ff980 > > [ 0.000000] ACPI: RSDT (v001 D845PT BG84510A > > 0x20020419 MSFT 0x00001011) @ 0x0fff0000 > > [ 0.000000] ACPI: FADT (v001 D845PT PT84510A > > 0x20020419 MSFT 0x00001011) @ 0x0fff1000 > > [ 0.000000] ACPI: MADT (v001 D845PT PT84510A > > 0x20020419 MSFT 0x00001011) @ 0x0ffe36fd > > [ 0.000000] ACPI: DSDT (v001 D845PT PT84510A > > 0x00000003 MSFT 0x0100000b) @ 0x00000000 > > [ 0.000000] ACPI: PM-Timer IO Port: 0x408 > > [ 0.000000] ACPI: Local APIC address 0xfee00000 > > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] > > lapic_id[0x00] enabled) > > [ 0.000000] Processor #0 15:2 APIC version 20 > > [ 0.000000] ACPI: LAPIC (acpi_id[0x02] > > lapic_id[0x01] disabled) > > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl > > lint[0x1]) > > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl > > lint[0x1]) > > [ 0.000000] ACPI: IOAPIC (id[0x02] > > address[0xfec00000] gsi_base[0]) > > [ 0.000000] IOAPIC[0]: apic_id 2, version 32, > > address 0xfec00000, GSI 0-23 > > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 > > global_irq 9 high level) > > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 > > global_irq 2 dfl dfl) > > [ 0.000000] ACPI: IRQ0 used by override. > > [ 0.000000] ACPI: IRQ2 used by override. > > [ 0.000000] ACPI: IRQ9 used by override. > > [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O > > APICs > > [ 0.000000] Using ACPI (MADT) for SMP configuration > > information > > [ 0.000000] Allocating PCI resources starting at > > 20000000 (gap: 10000000:eec00000) > > [ 0.000000] Detected 1794.351 MHz processor. > > [ 9.451070] Built 1 zonelists. Total pages: 64961 > > [ 9.451076] Kernel command line: > > root=UUID=99367c6a-4432-40ac-8331-73bc5a5d2d15 ro > > quiet splash > > [ 9.451321] mapped APIC to ffffd000 (fee00000) > > [ 9.451325] mapped IOAPIC to ffffc000 (fec00000) > > [ 9.451330] Enabling fast FPU save and restore... > > done. > > [ 9.451334] Enabling unmasked SIMD FPU exception > > support... done. > > [ 9.451351] Initializing CPU#0 > > [ 9.451455] PID hash table entries: 1024 (order: > > 10, 4096 bytes) > > [ 9.453066] Console: colour VGA+ 80x25 > > [ 9.453317] Dentry cache hash table entries: 32768 > > (order: 5, 131072 bytes) > > [ 9.453534] Inode-cache hash table entries: 16384 > > (order: 4, 65536 bytes) > > [ 9.462109] Memory: 248632k/261888k available > > (1993k kernel code, 12720k reserved, 900k data, 328k > > init, 0k highmem) > > [ 9.462125] virtual kernel memory layout: > > [ 9.462127] fixmap : 0xfff4e000 - 0xfffff000 > > ( 708 kB) > > [ 9.462128] pkmap : 0xff800000 - 0xffc00000 > > (4096 kB) > > [ 9.462130] vmalloc : 0xd0800000 - 0xff7fe000 > > ( 751 MB) > > [ 9.462132] lowmem : 0xc0000000 - 0xcffc0000 > > ( 255 MB) > > [ 9.462133] .init : 0xc03d9000 - 0xc042b000 > > ( 328 kB) > > [ 9.462135] .data : 0xc02f2429 - 0xc03d36d4 > > ( 900 kB) > > [ 9.462136] .text : 0xc0100000 - 0xc02f2429 > > (1993 kB) > > [ 9.462141] Checking if this processor honours the > > WP bit even in supervisor mode... Ok. > > [ 9.539353] Calibrating delay using timer specific > > routine.. 3592.13 BogoMIPS (lpj=7184275) > > [ 9.539419] Security Framework v1.0.0 initialized > > [ 9.539429] SELinux: Disabled at boot. > > [ 9.539455] Mount-cache hash table entries: 512 > > [ 9.539678] CPU: After generic identify, caps: > > 3febfbff 00000000 00000000 00000000 00000000 00000000 > > 00000000 > > [ 9.539697] CPU: Trace cache: 12K uops, L1 D cache: > > 8K > > [ 9.539701] CPU: L2 cache: 512K > > [ 9.539704] CPU: Hyper-Threading is disabled > > [ 9.539707] CPU: After all inits, caps: 3febfbff > > 00000000 00000000 00003080 00000000 00000000 00000000 > > [ 9.539723] Compat vDSO mapped to ffffe000. > > [ 9.539729] Remapping vsyscall page to ffffe000 > > [ 9.539747] Checking 'hlt' instruction... OK. > > [ 9.555528] SMP alternatives: switching to UP code > > [ 9.555844] Freeing SMP alternatives: 11k freed > > [ 9.556180] Early unpacking initramfs... done > > [ 10.012053] ACPI: Core revision 20060707 > > [ 10.012365] ACPI: Looking for DSDT in initramfs... > > file /DSDT.aml not found, using machine DSDT. > > [ 10.015771] CPU0: Intel(R) Pentium(R) 4 CPU 1.80GHz > > stepping 04 > > [ 10.015829] Total of 1 processors activated > > (3592.13 BogoMIPS). > > [ 10.015981] ENABLING IO-APIC IRQs > > [ 10.016192] ..TIMER: vector=0x31 apic1=0 pin1=2 > > apic2=-1 pin2=-1 > > [ 10.162650] Brought up 1 CPUs > > [ 10.163030] Booting paravirtualized kernel on bare > > hardware > > [ 10.163138] Time: 20:11:16 Date: 10/04/107 > > [ 10.163181] NET: Registered protocol family 16 > > [ 10.163322] EISA bus registered > > [ 10.163330] ACPI: bus type pci registered > > [ 10.163491] PCI: PCI BIOS revision 2.10 entry at > > 0xfda95, last bus=2 > > [ 10.163495] PCI: Using configuration type 1 > > [ 10.163497] Setting up standard PCI resources > > [ 10.171062] ACPI: Interpreter enabled > > [ 10.171068] ACPI: Using IOAPIC for interrupt > > routing > > [ 10.171762] ACPI: PCI Root Bridge [PCI0] (0000:00) > > [ 10.171775] PCI: Probing PCI hardware (bus 00) > > [ 10.172283] PCI quirk: region 0400-047f claimed by > > ICH4 ACPI/GPIO/TCO > > [ 10.172290] PCI quirk: region 0500-053f claimed by > > ICH4 GPIO > > [ 10.172712] Boot video device is 0000:01:00.0 > > [ 10.172847] PCI: Firmware left 0000:02:08.0 e100 > > interrupts enabled, disabling > > [ 10.173005] PCI: Transparent bridge - 0000:00:1e.0 > > [ 10.173040] ACPI: PCI Interrupt Routing Table > > [\_SB_.PCI0._PRT] > > [ 10.182046] ACPI: PCI Interrupt Routing Table > > [\_SB_.PCI0.PCI1._PRT] > > [ 10.184961] ACPI: Power Resource [FDDP] (off) > > [ 10.185579] ACPI: Power Resource [URP1] (off) > > [ 10.186298] ACPI: Power Resource [URP2] (off) > > [ 10.187122] ACPI: Power Resource [LPTP] (off) > > [ 10.189080] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 > > 4 5 6 7 9 10 *11 12 14 15) > > [ 10.189404] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 > > 4 5 6 7 *9 10 11 12 14 15) > > [ 10.189723] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 > > 4 5 6 7 9 10 11 12 14 15) *0, disabled. > > [ 10.190046] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 > > 4 5 6 7 9 10 *11 12 14 15) > > [ 10.190374] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 > > 4 5 6 7 9 10 *11 12 14 15) > > [ 10.190706] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 > > 4 5 6 7 9 10 11 12 14 15) *0, disabled. > > [ 10.191025] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 > > 4 5 6 7 9 10 *11 12 14 15) > > [ 10.191355] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 > > 4 5 6 7 9 *10 11 12 14 15) > > [ 10.191532] Linux Plug and Play Support v0.97 (c) > > Adam Belay > > [ 10.191552] pnp: PnP ACPI init > > [ 10.196199] pnp: PnP ACPI: found 13 devices > > [ 10.196207] PnPBIOS: Disabled by ACPI PNP > > [ 10.196285] PCI: Using ACPI for IRQ routing > > [ 10.196290] PCI: If a device doesn't work, try > > "pci=routeirq". If it helps, post a report > > [ 10.200214] NET: Registered protocol family 8 > > [ 10.200217] NET: Registered protocol family 20 > > [ 10.201021] PCI: Bridge: 0000:00:01.0 > > [ 10.201026] IO window: c000-cfff > > [ 10.201032] MEM window: ff800000-ff8fffff > > [ 10.201038] PREFETCH window: ec900000-f49fffff > > [ 10.201044] PCI: Bridge: 0000:00:1e.0 > > [ 10.201049] IO window: d000-dfff > > [ 10.201056] MEM window: ff900000-ff9fffff > > [ 10.201062] PREFETCH window: f4a00000-f6afffff > > [ 10.201086] PCI: Setting latency timer of device > > 0000:00:1e.0 to 64 > > [ 10.201128] NET: Registered protocol family 2 > > [ 10.226633] IP route cache hash table entries: 2048 > > (order: 1, 8192 bytes) > > [ 10.226753] TCP established hash table entries: > > 8192 (order: 4, 65536 bytes) > > [ 10.226817] TCP bind hash table entries: 4096 > > (order: 3, 32768 bytes) > > [ 10.226849] TCP: Hash tables configured > > (established 8192 bind 4096) > > [ 10.226853] TCP reno registered > > [ 10.238681] checking if image is initramfs... it is > > [ 11.143925] Freeing initrd memory: 6769k freed > > [ 11.144589] audit: initializing netlink socket > > (disabled) > > [ 11.144613] audit(1194207076.772:1): initialized > > [ 11.144825] VFS: Disk quotas dquot_6.5.1 > > [ 11.144858] Dquot-cache hash table entries: 1024 > > (order 0, 4096 bytes) > > [ 11.144935] io scheduler noop registered > > [ 11.144940] io scheduler anticipatory registered > > [ 11.144944] io scheduler deadline registered > > [ 11.144958] io scheduler cfq registered (default) > > [ 11.145317] isapnp: Scanning for PnP cards... > > [ 11.500844] isapnp: No Plug & Play device found > > [ 11.540210] Real Time Clock Driver v1.12ac > > [ 11.540289] Serial: 8250/16550 driver $Revision: > > 1.90 $ 4 ports, IRQ sharing enabled > > [ 11.540438] serial8250: ttyS0 at I/O 0x3f8 (irq = > > 4) is a 16550A > > [ 11.540656] serial8250: ttyS1 at I/O 0x2f8 (irq = > > 3) is a 16550A > > [ 11.541660] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is > > a 16550A > > [ 11.542045] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is > > a 16550A > > [ 11.542334] ACPI: PCI Interrupt 0000:02:0a.0[A] -> > > GSI 22 (level, low) -> IRQ 16 > > [ 11.542346] ACPI: PCI interrupt for device > > 0000:02:0a.0 disabled > > [ 11.542447] mice: PS/2 mouse device common for all > > mice > > [ 11.543350] RAMDISK driver initialized: 16 RAM > > disks of 65536K size 1024 blocksize > > [ 11.543732] input: Macintosh mouse button emulation > > as /class/input/input0 > > [ 11.543795] Uniform Multi-Platform E-IDE driver > > Revision: 7.00alpha2 > > [ 11.543802] ide: Assuming 33MHz system bus speed > > for PIO modes; override with idebus=xx > > [ 11.544119] PNP: PS/2 Controller > > [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 > > [ 11.547995] serio: i8042 KBD port at 0x60,0x64 irq > > 1 > > [ 11.548008] serio: i8042 AUX port at 0x60,0x64 irq > > 12 > > [ 11.548253] EISA: Probing bus 0 at eisa.0 > > [ 11.548298] EISA: Detected 0 cards. > > [ 11.578409] TCP cubic registered > > [ 11.578419] NET: Registered protocol family 1 > > [ 11.578453] Using IPI No-Shortcut mode > > [ 11.578555] ACPI: (supports S0 S1 S4 S5) > > [ 11.578621] Magic number: 15:69:194 > > [ 11.578707] hash matches device ttys6 > > [ 11.579370] Freeing unused kernel memory: 328k > > freed > > [ 11.580843] Time: tsc clocksource has been > > installed. > > [ 11.594959] input: AT Translated Set 2 keyboard as > > /class/input/input1 > > [ 12.902122] Capability LSM initialized > > [ 12.963583] ACPI Exception (acpi_processor-0677): > > AE_NOT_FOUND, Processor Device is not present > > [20060707] > > [ 13.757101] SCSI subsystem initialized > > [ 13.766455] libata version 2.20 loaded. > > [ 13.772683] ata_piix 0000:00:1f.1: version 2.10ac1 > > [ 13.772727] PCI: Setting latency timer of device > > 0000:00:1f.1 to 64 > > [ 13.772809] ata1: PATA max UDMA/100 cmd 0x000101f0 > > ctl 0x000103f6 bmdma 0x0001ffa0 irq 14 > > [ 13.772858] ata2: PATA max UDMA/100 cmd 0x00010170 > > ctl 0x00010376 bmdma 0x0001ffa8 irq 15 > > [ 13.772882] scsi0 : ata_piix > > [ 13.815194] usbcore: registered new interface > > driver usbfs > > [ 13.815231] usbcore: registered new interface > > driver hub > > [ 13.815266] usbcore: registered new device driver > > usb > > [ 13.843582] USB Universal Host Controller Interface > > driver v3.0 > > [ 13.858300] e100: Intel(R) PRO/100 Network Driver, > > 3.5.17-k2-NAPI > > [ 13.858306] e100: Copyright(c) 1999-2006 Intel > > Corporation > > [ 13.934587] ata1.00: ata_hpa_resize 1: sectors = > > 40020624, hpa_sectors = 40020624 > > [ 13.934594] ata1.00: ATA-6: Maxtor 2B020H1, > > WAH21PB0, max UDMA/100 > > [ 13.934599] ata1.00: 40020624 sectors, multi 16: > > LBA > > [ 13.942624] ata1.00: ata_hpa_resize 1: sectors = > > 40020624, hpa_sectors = 40020624 > > [ 13.942632] ata1.00: configured for UDMA/100 > > [ 13.942652] scsi1 : ata_piix > > [ 14.069576] Floppy drive(s): fd0 is 1.44M > > [ 14.089574] FDC 0 is a post-1991 82077 > > [ 14.277836] ata2.00: ATAPI, max UDMA/33 > > [ 14.457620] ata2.00: configured for UDMA/33 > > [ 14.457827] scsi 0:0:0:0: Direct-Access ATA > > Maxtor 2B020H1 WAH2 PQ: 0 ANSI: 5 > > [ 14.462542] scsi 1:0:0:0: CD-ROM MITSUMI > > CR-48XATE 1.0E PQ: 0 ANSI: 5 > > [ 14.462922] ACPI: PCI Interrupt 0000:00:1f.2[D] -> > > GSI 19 (level, low) -> IRQ 17 > > [ 14.462941] PCI: Setting latency timer of device > > 0000:00:1f.2 to 64 > > [ 14.462947] uhci_hcd 0000:00:1f.2: UHCI Host > > Controller > > [ 14.463155] uhci_hcd 0000:00:1f.2: new USB bus > > registered, assigned bus number 1 > > [ 14.463190] uhci_hcd 0000:00:1f.2: irq 17, io base > > 0x0000ef40 > > [ 14.463356] usb usb1: configuration #1 chosen from > > 1 choice > > [ 14.463403] hub 1-0:1.0: USB hub found > > [ 14.463416] hub 1-0:1.0: 2 ports detected > > [ 14.490042] SCSI device sda: 40020624 512-byte hdwr > > sectors (20491 MB) > > [ 14.490347] sda: Write Protect is off > > [ 14.490351] sda: Mode Sense: 00 3a 00 00 > > [ 14.490383] SCSI device sda: write cache: enabled, > > read cache: enabled, doesn't support DPO or FUA > > [ 14.490477] SCSI device sda: 40020624 512-byte hdwr > > sectors (20491 MB) > > [ 14.490494] sda: Write Protect is off > > [ 14.490497] sda: Mode Sense: 00 3a 00 00 > > [ 14.490524] SCSI device sda: write cache: enabled, > > read cache: enabled, doesn't support DPO or FUA > > [ 14.490529] sda: sda1 sda2 < sda5 > > > [ 14.539763] sd 0:0:0:0: Attached scsi disk sda > > [ 14.546930] sd 0:0:0:0: Attached scsi generic sg0 > > type 0 > > [ 14.547098] sr 1:0:0:0: Attached scsi generic sg1 > > type 5 > > [ 14.565494] ACPI: PCI Interrupt 0000:00:1f.4[C] -> > > GSI 23 (level, low) -> IRQ 18 > > [ 14.565515] PCI: Setting latency timer of device > > 0000:00:1f.4 to 64 > > [ 14.565521] uhci_hcd 0000:00:1f.4: UHCI Host > > Controller > > [ 14.565616] uhci_hcd 0000:00:1f.4: new USB bus > > registered, assigned bus number 2 > > [ 14.565652] uhci_hcd 0000:00:1f.4: irq 18, io base > > 0x0000ef80 > > [ 14.565861] usb usb2: configuration #1 chosen from > > 1 choice > > [ 14.565902] hub 2-0:1.0: USB hub found > > [ 14.565915] hub 2-0:1.0: 2 ports detected > > [ 14.574554] sr0: scsi3-mmc drive: 40x/40x writer > > cd/rw xa/form2 cdda tray > > [ 14.574563] Uniform CD-ROM driver Revision: 3.20 > > [ 14.574905] sr 1:0:0:0: Attached scsi CD-ROM sr0 > > [ 14.669488] ACPI: PCI Interrupt 0000:02:08.0[A] -> > > GSI 20 (level, low) -> IRQ 19 > > [ 14.692915] e100: eth0: e100_probe: addr > > 0xff9ff000, irq 19, MAC addr 00:03:47:FF:40:7F > > [ 14.769987] Attempting manual resume > > [ 14.769993] swsusp: Resume From Partition 8:5 > > [ 14.769996] PM: Checking swsusp image. > > [ 14.770250] PM: Resume from disk failed. > > [ 14.829353] kjournald starting. Commit interval 5 > > seconds > > [ 14.829371] EXT3-fs: mounted filesystem with > > ordered data mode. > > [ 14.908845] usb 2-2: new full speed USB device > > using uhci_hcd and address 2 > > [ 15.063105] usb 2-2: configuration #1 chosen from 1 > > choice > > [ 15.066004] hub 2-2:1.0: USB hub found > > [ 15.068962] hub 2-2:1.0: 4 ports detected > > [ 30.103649] pci_hotplug: PCI Hot Plug PCI Core > > version: 0.5 > > [ 30.140244] shpchp: Standard Hot Plug PCI > > Controller Driver version: 0.4 > > [ 30.171105] iTCO_vendor_support: vendor-support=0 > > [ 30.172617] iTCO_wdt: Intel TCO WatchDog Timer > > Driver v1.01 (11-Nov-2006) > > [ 30.172702] iTCO_wdt: failed to reset NO_REBOOT > > flag, reboot disabled by hardware > > [ 30.172711] iTCO_wdt: No card detected > > [ 30.202397] Linux agpgart interface v0.102 (c) Dave > > Jones > > [ 30.203436] intel_rng: Firmware space is locked > > read-only. If you can't or > > [ 30.203439] intel_rng: don't want to disable this > > in firmware setup, and if > > [ 30.203441] intel_rng: you are certain that your > > system has a functional > > [ 30.203443] intel_rng: RNG, try using the > > 'no_fwh_detect' option. > > [ 30.221831] agpgart: Detected an Intel i845 > > Chipset. > > [ 30.225856] agpgart: AGP aperture is 64M @ > > 0xf8000000 > > [ 31.198167] slamr: module license 'Smart Link Ltd.' > > taints kernel. > > [ 31.207195] slamr: SmartLink AMRMO modem. > > [ 31.207546] slamr: probe 2000:2800 SL2800 card... > > [ 31.207561] ACPI: PCI Interrupt 0000:02:0a.0[A] -> > > GSI 22 (level, low) -> IRQ 16 > > [ 31.207734] slamr: slamr0 is SL2800 card. > > [ 31.223178] input: PC Speaker as > > /class/input/input2 > > [ 31.241596] parport: PnPBIOS parport detected. > > [ 31.241627] parport0: PC-style at 0x378, irq 7 > > [PCSPP,TRISTATE,EPP] > > [ 31.436112] input: ImPS/2 Generic Wheel Mouse as > > /class/input/input3 > > [ 31.704422] ACPI: PCI Interrupt 0000:00:1f.5[B] -> > > GSI 17 (level, low) -> IRQ 20 > > [ 31.704495] PCI: Setting latency timer of device > > 0000:00:1f.5 to 64 > > [ 32.020051] intel8x0_measure_ac97_clock: measured > > 56160 usecs > > [ 32.020057] intel8x0: clocking to 41156 > > [ 32.198543] lp0: using parport0 (interrupt-driven). > > [ 32.244203] Adding 746980k swap on > > /dev/disk/by-uuid/bbd8a94a-e7da-43a5-b929-78542e176fff. > > Priority:-1 extents:1 across:746980k > > [ 32.383712] EXT3 FS on sda1, internal journal > > [ 34.125282] NET: Registered protocol family 17 > > [ 34.819247] Using specific hotkey driver > > [ 34.880824] No dock devices found. > > [ 34.967436] ibm_acpi: ec object not found > > [ 35.135749] input: Power Button (FF) as > > /class/input/input4 > > [ 35.142460] ACPI: Power Button (FF) [PWRF] > > [ 35.192328] input: Power Button (CM) as > > /class/input/input5 > > [ 35.192632] ACPI: Power Button (CM) [PBTN] > > [ 35.344902] pcc_acpi: loading... > > [ 39.690860] e100: eth1: e100_watchdog: link up, > > 100Mbps, full-duplex > > [ 40.214725] ppdev: user-space parallel port driver > > [ 41.705029] apm: BIOS not found. > > [ 42.569243] Bluetooth: Core ver 2.11 > > [ 42.569336] NET: Registered protocol family 31 > > [ 42.569339] Bluetooth: HCI device and connection > > manager initialized > > [ 42.569344] Bluetooth: HCI socket layer initialized > > [ 42.628593] Bluetooth: L2CAP ver 2.8 > > [ 42.628600] Bluetooth: L2CAP socket layer > > initialized > > [ 42.702425] Bluetooth: RFCOMM socket layer > > initialized > > [ 42.702446] Bluetooth: RFCOMM TTY layer initialized > > [ 42.702449] Bluetooth: RFCOMM ver 1.8 > > [ 45.469306] [drm] Initialized drm 1.1.0 20060810 > > [ 45.477995] ACPI: PCI Interrupt 0000:01:00.0[A] -> > > GSI 16 (level, low) -> IRQ 21 > > [ 45.482326] [drm] Initialized r128 2.5.0 20030725 > > on minor 0 > > [ 45.483442] agpgart: Found an AGP 2.0 compliant > > device at 0000:00:00.0. > > [ 45.483957] agpgart: Putting AGP V2 device at > > 0000:00:00.0 into 1x mode > > [ 45.484240] agpgart: Putting AGP V2 device at > > 0000:01:00.0 into 1x mode > > user1@kubuntu704:~$ > > > > > > > > Bob Terrell > > Lubbock, Texas > > bob_terrell_texas@xxxxxxxxx > > > > > > > > __________________________________________________ > > Do You Yahoo!? > > Tired of spam? Yahoo! Mail has the best spam protection around > > http://mail.yahoo.com >
