Hi Still doesn't work, I guess I might just be out of luck. I've noticed support for this modem seems quite new (I tried with a 2.6.18 kernel and ALSA doesn't neem to detect it at all, for example in `aplay -l`). Thanks for the help nevertheless, Firas On Saturday 07 April 2007 01:48:18 you wrote: > RE: NO CARRIER > There should be a line within /etc/wvdial.conf > Carrier Check = no > > MarvS > > On 4/6/07, Firas Kraiem <fkraiem@xxxxxxx> wrote: > > Hi and thanks for the answer > > > > Unfortunately, hw:0,6 gives the same error when trying to dial. Just > > to make sure it wasn't Gentoo's slmodemd bugging on me, I got one from > > http://linmodems.technion.ac.il/packages/smartlink/ with the same > > results. > > > > Other ideas ? > > > > Firas > > > > Quoting Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>: > > > Firas, > > > > > > For you modem subsytem card: > > > ------------------------------- > > > Codec: Motorola Si3054 > > > Address: 1 > > > Vendor Id: 0x10573055 > > > > > > 00-06: Si3054 Modem : Si3054 Modem : playback 1 : capture 1 > > > 00-02: ALC880 Analog : ALC880 Analog : capture 2 > > > 00-01: ALC880 Digital : ALC880 Digital : playback 1 > > > 00-00: ALC880 Analog : ALC880 Analog : playback 1 : capture 2 > > > -------- > > > shows that your hw:0 us likely addressing the audio, while hw:0,6 is > > > the modem SUbsytem. > > > > > > Activate the modem with: > > > $ sudo slmodemd -c FRANCE --alsa hw:0,6 > > > > > > MarvS > > > scanModem maintainer > > > > > > /proc/asound/modules > > > ------------------------------- > > > 0 snd_hda_intel > > > /proc/asound/card0/codec#1 > > > ------------------------------- > > > Codec: Motorola Si3054 > > > Address: 1 > > > Vendor Id: 0x10573055 > > > Subsystem Id: 0x104310c6 > > > Revision Id: 0x100700 > > > > > > On 4/1/07, Firas Kraiem <fkraiem@xxxxxxx> wrote: > > >> Greetings > > >> > > >> As the title says, I'm having issues configuring the built-in modem on > > >> my laptop in Gentoo, with a 2.6.20 kernel. The modem is most likely > > >> hosted by the Intel HDA sound card but I attached the modemData.txt > > >> nevertheless. > > >> > > >> What i've done so far : > > >> > > >> -> installed slmodemd fro the Gentoo portage > > >> -> modprobe'd snd_intel8x0m > > >> -> lauched slmodemd with the following command : > > >> > > >> mfb@ana ~ $ sudo /usr/sbin/slmodemd -c FRANCE --alsa hw:0 > > >> > > >> -> wvdialconf seems to detect the modem correctly : > > >> > > >> mfb@ana ~ $ sudo wvdialconf /etc/wvdial.conf > > >> Editing `/etc/wvdial.conf'. > > >> > > >> Scanning your serial ports for a modem. > > >> > > >> Modem Port Scan<*1>: S0 S1 S2 S3 > > >> ttySL0<*1>: ATQ0 V1 E1 -- OK > > >> ttySL0<*1>: ATQ0 V1 E1 Z -- OK > > >> ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK > > >> ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK > > >> ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK > > >> ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > > >> ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem > > >> ttySL0<*1>: Speed 4800: AT -- OK > > >> ttySL0<*1>: Speed 9600: AT -- OK > > >> ttySL0<*1>: Speed 19200: AT -- OK > > >> ttySL0<*1>: Speed 38400: AT -- OK > > >> ttySL0<*1>: Speed 57600: AT -- OK > > >> ttySL0<*1>: Speed 115200: AT -- OK > > >> ttySL0<*1>: Speed 230400: AT -- OK > > >> ttySL0<*1>: Speed 460800: AT -- OK > > >> ttySL0<*1>: Max speed is 460800; that should be safe. > > >> ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > > >> > > >> Found a modem on /dev/ttySL0. > > >> Modem configuration written to /etc/wvdial.conf. > > >> ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 > > >> +FCLASS=0" > > >> > > >> However, when I try to run wvdial : > > >> > > >> mfb@ana ~ $ sudo wvdial > > >> --> WvDial: Internet dialer version 1.56 > > >> --> Initializing modem. > > >> --> Sending: ATZ > > >> ATZ > > >> OK > > >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > >> OK > > >> --> Modem initialized. > > >> --> Sending: ATDT0860922000 > > >> --> Waiting for carrier. > > >> ATDT0860922000 > > >> NO CARRIER > > >> ERROR > > >> --> No Carrier! Trying again. > > >> > > >> It might be worth noting that while I get all the "NO CARRIER" > > >> messages in wvdial, I get those messages in the terminal I launched > > >> slmodemd from : > > >> > > >> error: cannot setup hw params for playback: Invalid argument > > >> > > >> I've tried modem:0 instead of hw:0 when launching slmodemd with the > > >> same results so now I'm stuck. Help would be much appreciated. > > >> > > >> Firas. > > >> -- > > >> () ascii ribbon campaign - against html e-mail > > >> /\ www.asciiribbon.org - against proprietary attachments > > > > -- > > () ascii ribbon campaign - against HTML e-mail > > /\ www.asciiribbon.org - against proprietary attachments -- () ascii ribbon campaign - against html e-mail /\ www.asciiribbon.org - against proprietary attachments
Attachment:
pgpVDaIPVHxUw.pgp
Description: PGP signature
