Dear all, following the details according to the instructions of Jacques. - accurate removal of previous driver installation; - downloaded latest scanModem; - run it and appending below ModemData.txt; - installed hsfmodem_7.60.00.01full_k2.6.17_10_generic_ubuntu_i386.deb installation OK with the quite normal message: Warning: no device detected by hsf driver - HDA modems may require reboot Note: kernel module snd-via82xx-modem overridden by hsfmc97via Note: kernel module snd-intel8x0m overridden by hsfmc97ich hsfmc97sis Note: kernel module snd-atiixp-modem overridden by hsfmc97ati and sound system stopped functioning; - full system reboot but nothing changed; - tried as instructed by Linuxant: disabling the sound system, sudo hsfstop sudo hsfconfig -i the system spends more time in executing the second instruction but no way to have modem recognized (repeated also after reboot). - Removing the driver the sound system is working again (after reboot). - For completness I am appending below part of hsfdiag.txt. - This modem appears however to be a conexant, as windows drivers state so (I added that output to my first mail, but I have seen now that it was truncated on pasting by my mail client); I can resend it if required. Marvin, sorry for the inconvenience of the html format, I was sending those two mails from a different location and was not aware of the setting. Hope it is OK now. Thanks for your attention. Regards Antonio START ModemData.txt --------------------------------------------------------- -------------------------- System information ---------------------------- CPU=i686, Ubuntu 6.10 Linux version 2.6.17-10-generic (root@vernadsky) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Fri Oct 13 18:45:35 UTC 2006 (Ubuntu 2.6.17-10.33-generic) scanModem update of: 2007_Feb_28 USB modem not detected by lsusb Modem or host audio card candidates have firmware information: PCI slot PCI ID SubsystemID Name ---------- --------- --------- -------------- 00:14.2 1002:437b 1025:009f Audio device: ATI Technologies Inc Unknown device 437b Modem interrupt assignment and sharing: 209: 13900 1 IO-APIC-level HDA Intel --- Bootup diagnositcs for card in PCI slot 00:14.2 ---- === Finished modem firmware and bootup diagnostics section. === === Next deducing cogent software === ALSAversion 1.0.11 /proc/asound/SB/codec#1:Vendor Id: 0x14f12bfa /proc/asound/card0/codec#1:Vendor Id: 0x14f12bfa ------ 14f1 is the Conexant Vendor ID, and 0x14f12bfa a softmodem chipset. Get a hsfmodem package through http://www.linuxant.com 1002:437b is a High Definition Audio card, possibly hosting a soft modem. For candidate modem in PCI bus: 00:14.2 Class 0403: 1002:437b Audio device: ATI Technologies Inc Unknown device 437b Primary PCI_id 1002:437b Subsystem PCI_id 1025:009f Softmodem codec or Vendor from diagnostics: 14f1, a Conexant type, from Archives: 14f1, a Conexant type, Lacking a dsp (digital signal processing) chip, the modem is a software intensive or "softmodem" type. Its primary controller manages the traffic with the CPU. But the software needed is specified in the Subsystem. ----------------------------------------- Support type needed or chipset: hsfmodem The diagnostic outputs for this softmodem section have their raw information in folders and text files under /proc/asound/ which you can browse. The information is from files: /proc/asound/pcm ------------------------------- 00-01: ALC883 Analog : ALC883 Analog : capture 2 00-00: ALC883 Analog : ALC883 Analog : playback 1 : capture 2 /proc/asound/modules ------------------------------- 0 snd_hda_intel /proc/asound/card0/codec#1 ------------------------------- Codec: Generic 14f1 ID 2bfa Address: 1 Vendor Id: 0x14f12bfa Subsystem Id: 0x1025009f Revision Id: 0x90000 ------------------------------- Current support status of HDA cards is: Vendor IDs Chip maker Support type ---------- ---------- ------------- 0x14f12bfa Conexant hsfmodem , not slmodemd compatible 0x11c13026 AgereSystems snd-hda-intel, slmodemd supported 0x11c11040 AgereSystems " " , patch needed 0x11c13055 AgereSystems " " , " 0x163c3055 Smartlink " " , " 0x163c3155 " " " , " 0x10573055 Motorola " " , " 0x10573155 " " " , "" as of October 2006. and from the command: aplay -l | grep -i modem ----------------end Softmodem section -------------- Formal support for Conexant chipset modems are available ONLY through http://www.linuxant.com/drivers. Read Conexant.txt for details. and Modem/YourSystem.txt for follow through guidance. Driver speed is limited to 14,400 until a key is purchased. There is NO freeware alternative. There are two support package types: hsfmodem and hcflinmodem. http://www.lorenzobettini.it/linux/LinuxSonyVaioVGN-S5VP_B reports a problem and solution in stalling a key, after testing of the free low speed download. The hsfmodem package serves a great variety of Conexant chipset modems. From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php download hsfmodem_VersionSpec_k2.6.17_10_generic_ubuntu_i386.deb.zip with 2.6.17_10_generic equivalent to 2.6.17-10-generic, your kernel version. Under Linux unpack with: $ unzip hsfmodem*.zip Then install with: $ sudo dpkg -i hsfmodem*.deb Subsequently, the modem should be found with $ sudo wvdialconf /etc/wvdial.conf Edit in your personal information with: $ sudo gedit /etc/wvdial.conf and try dialing out with: $ sudo wvdial. See Testing.txt for details. Read Conexant.txt Writing Conexant.txt Completed candidate modem analyses. The base of the UDEV device file system is: /dev/.udev Versions adequately match for the compiler installed: 4.1.2 and the compiler used in kernel assembly: 4.1.2 Compiling resources appear complete: make utility - /usr/bin/make Compiler version 4.1 kernel_headers base folder /lib/modules/2.6.17-10-generic/build Checking pppd properties: -rwsr-xr-- 1 root dip 260920 2006-07-10 21:13 /usr/sbin/pppd In case of an "error 17" "serial loopback" problem, see: http://phep2.technion.ac.il/linmodems/archive-sixth/msg02637.html To enable dialout without Root permission do: $ su - root (not for Ubuntu) sudo chmod a+x /usr/sbin/pppd or under Ubuntu related Linuxes sudo chmod a+x /usr/sbin/pppd Checking settings of: /etc/ppp/options asyncmap 0 auth crtscts lock hide-password modem proxyarp lcp-echo-interval 30 lcp-echo-failure 4 noipx In case of a message like: Warning: Could not modify /etc/ppp/pap-secrets: Permission denied see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html Read Modem/YourSystem.txt concerning other COMM channels: ath0 eth0 wifi0 Which can interfere with Browser naviagation. Don't worry about the following, it is for the experts should trouble shooting be necessary. ========================================================== Checking for modem support lines: -------------------------------------- /device/modem symbolic link: slmodemd created symbolic link /dev/ttySL0: Within /etc/udev/ files: /etc/udev/rules.d/60-symlinks.rules:# Create /dev/modem symlink /etc/udev/rules.d/60-symlinks.rules:KERNEL=="ttyLTM[0-9]*", SYMLINK+="modem" Within /etc/modprobe.conf files: /etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2 /etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2 /etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to blacklist unwanted modem drivers /etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem /etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem Within any ancient /etc/devfs files: Within ancient kernel 2.4.n /etc/module.conf files: --------- end modem support lines -------- END ModemData.txt ----------------------------------------------------------- START hsfdiag.txt ----------------------------------------------------------- + hsfstop + modprobe -v /dev/ttySHSF install /sbin/modprobe hsfpcibasic2; /sbin/modprobe hsfmc97ich; /sbin/modprobe hsfmc97via; /sbin/modprobe hsfmc97ali; /sbin/modprobe hsfmc97ati; /sbin/modprobe hsfmc97sis; [ -e /lib/modules/`uname -r`/extra/hsfusbcd2.ko ] && /sbin/modprobe hsfusbcd2; /sbin/modprobe snd_hda_intel; /bin/true insmod /lib/modules/2.6.17-10-generic/extra/hsfsoar.ko insmod /lib/modules/2.6.17-10-generic/extra/hsfosspec.ko dcpmajor=242 diagmajor=243 insmod /lib/modules/2.6.17-10-generic/extra/hsfengine.ko insmod /lib/modules/2.6.17-10-generic/extra/hsfserial.ko serialmajor=240 insmod /lib/modules/2.6.17-10-generic/extra/hsfpcibasic2.ko insmod /lib/modules/2.6.17-10-generic/extra/hsfmc97ich.ko insmod /lib/modules/2.6.17-10-generic/extra/hsfmc97via.ko insmod /lib/modules/2.6.17-10-generic/extra/hsfmc97ali.ko insmod /lib/modules/2.6.17-10-generic/extra/hsfmc97ati.ko insmod /lib/modules/2.6.17-10-generic/extra/hsfmc97sis.ko insmod /lib/modules/2.6.17-10-generic/extra/hsfusbcd2.ko insmod /lib/modules/2.6.17-10-generic/extra/snd-hda-codec.ko insmod /lib/modules/2.6.17-10-generic/extra/snd-hda-intel.ko + lsmod Module Size Used by hsfhda 109096 0 snd_hda_intel 22424 0 snd_hda_codec 211596 2 hsfhda,snd_hda_intel hsfusbcd2 66088 0 hsfmc97sis 68120 0 hsfmc97ati 66840 0 hsfmc97ali 73376 0 hsfmc97via 69280 0 hsfmc97ich 71448 0 hsfpcibasic2 67608 0 hsfserial 25188 8 hsfhda,hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2 hsfengine 1296396 9 hsfhda,hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2,hsfserial hsfosspec 110184 10 hsfhda,hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2,hsfserial,hsfengine hsfsoar 86920 7 hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2 rfcomm 42260 0 l2cap 27136 5 rfcomm bluetooth 53476 4 rfcomm,l2cap powernow_k8 15008 1 cpufreq_userspace 5408 0 cpufreq_stats 7744 0 freq_table 6048 2 powernow_k8,cpufreq_stats cpufreq_powersave 2944 0 cpufreq_ondemand 8876 1 cpufreq_conservative 8712 0 video 17540 0 tc1100_wmi 8324 0 sony_acpi 6412 0 sbs 16804 0 pcc_acpi 14080 0 i2c_ec 6272 1 sbs i2c_core 23424 1 i2c_ec hotkey 11556 0 dev_acpi 12292 0 container 5632 0 button 7952 0 battery 11652 0 asus_acpi 17688 0 ac 6788 0 nls_iso8859_1 5248 1 nls_cp437 6912 1 vfat 14720 1 fat 56348 1 vfat nls_utf8 3200 1 ntfs 112116 1 parport_pc 37796 0 lp 12964 0 parport 39496 2 parport_pc,lp af_packet 24584 4 pcmcia 40380 0 joydev 11200 0 tsdev 9152 0 snd_pcm_oss 47360 0 snd_mixer_oss 19584 1 snd_pcm_oss yenta_socket 28812 1 rsrc_nonstatic 15360 1 yenta_socket 8139cp 24832 0 wlan_scan_sta 15744 1 8139too 29056 0 usbhid 45152 0 snd_pcm 84612 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd_timer 25348 1 snd_pcm ath_pci 100000 0 ath_rate_sample 16512 1 ath_pci wlan 207580 4 wlan_scan_sta,ath_pci,ath_rate_sample mii 6912 2 8139cp,8139too pcmcia_core 43924 3 pcmcia,yenta_socket,rsrc_nonstatic sdhci 20108 0 mmc_core 32392 1 sdhci ath_hal 192976 3 ath_pci,ath_rate_sample psmouse 41352 0 snd 58372 6 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer pcspkr 4352 0 serio_raw 8452 0 evdev 11392 2 soundcore 11232 1 snd ati_agp 10636 0 agpgart 34888 1 ati_agp snd_page_alloc 11400 2 snd_hda_intel,snd_pcm shpchp 42144 0 pci_hotplug 32828 1 shpchp ext3 142728 4 jbd 62228 1 ext3 ohci_hcd 22532 0 ehci_hcd 34696 0 usbcore 134912 6 hsfusbcd2,hsfosspec,usbhid,ohci_hcd,ehci_hcd ide_generic 2432 0 ide_cd 33696 0 cdrom 38944 1 ide_cd ide_disk 18560 8 generic 5764 0 atiixp 7824 1 thermal 15624 0 processor 31560 2 powernow_k8,thermal fan 6020 0 fbcon 41504 0 tileblit 3840 1 fbcon font 9344 1 fbcon bitblit 7168 1 fbcon softcursor 3328 1 bitblit vesafb 9244 0 capability 5896 0 commoncap 8704 1 capability + date Sun Mar 4 22:25:54 CET 2007 + /usr/sbin/hsfconfig --info Conexant HSF softmodem driver, version 7.60.00.01full If you need license keys, assistance or more information, please go to: http://www.linuxant.com/ When reporting a problem for the first time, please send us the file generated by "hsfconfig --dumpdiag". Note: kernel module snd-via82xx-modem overridden by hsfmc97via Note: kernel module snd-intel8x0m overridden by hsfmc97ich hsfmc97sis Note: kernel module snd-atiixp-modem overridden by hsfmc97ati Warning: no device detected by hsf driver - HDA modems may require reboot Note: kernel module snd-via82xx-modem overridden by hsfmc97via Note: kernel module snd-intel8x0m overridden by hsfmc97ich hsfmc97sis Note: kernel module snd-atiixp-modem overridden by hsfmc97ati + identify_system linux-i686(i686)-2.6.17-10-generic-SMP Ubuntu-Kubuntu-6.10 + uname -a Linux betel 2.6.17-10-generic #2 SMP Fri Oct 13 18:45:35 UTC 2006 i686 GNU/Linux + gcc -v Using built-in specs. Target: i486-linux-gnu Configured with: ../src/configure -v --enable-languages=c,c++,fortran,objc,obj-c++,treelang --prefix=/usr --enable-shared --with-system-zlib --libexecdir=/usr/lib --without-included-gettext --enable-threads=posix --enable-nls --program-suffix=-4.1 --enable-__cxa_atexit --enable-clocale=gnu --enable-libstdcxx-debug --enable-mpfr --enable-checking=release i486-linux-gnu Thread model: posix gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5) + cat -v /proc/version + cat -v /proc/cpuinfo + cat -v /etc/debian_version testing/unstable + cat -v /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=6.10 DISTRIB_CODENAME=edgy DISTRIB_DESCRIPTION="Ubuntu 6.10" + dmesg : invalid dep_range_val 0:7fff [17179987.384000] hda_codec: invalid dep_range_val 0:7fff . . . removed a bunch of similar lines [17179987.472000] hda_codec: invalid dep_range_val 0:7fff [17179987.800000] cnxthsf_OsEventWaitTime(d9ef38e0/HDA CodecUnsolicitedmessage, 40): returning OSEVENT_WAIT_TIMEOUT . . . removed some 40 similar lines [17179990.808000] cnxthsf_OsEventWaitTime(d9ef38e0/HDA CodecUnsolicitedmessage, 40): returning OSEVENT_WAIT_TIMEOUT [17179991.104000] cnxthsf_cnxt_serial_add: ComCtrlOpen failed (1) [17179991.104000] conexant_init: cnxthwhda_probe() failed: -19 [17179991.104000] ACPI: PCI interrupt for device 0000:00:14.2 disabled + cat -v /var/run/hsfdcpd0.err + cat -v /var/run/hsfdcpd0.out + lspci -n 00:00.0 0600: 1002:5950 (rev 10) 00:01.0 0604: 1002:5a3f 00:04.0 0604: 1002:5a36 00:05.0 0604: 1002:5a37 00:13.0 0c03: 1002:4374 (rev 80) 00:13.1 0c03: 1002:4375 (rev 80) 00:13.2 0c03: 1002:4373 (rev 80) 00:14.0 0c05: 1002:4372 (rev 83) 00:14.1 0101: 1002:4376 (rev 80) 00:14.2 0403: 1002:437b (rev 01) 00:14.3 0601: 1002:4377 (rev 80) 00:14.4 0604: 1002:4371 (rev 80) 00:18.0 0600: 1022:1100 00:18.1 0600: 1022:1101 00:18.2 0600: 1022:1102 00:18.3 0600: 1022:1103 01:05.0 0300: 1002:5975 06:01.0 0200: 10ec:8139 (rev 10) 06:02.0 0200: 168c:001a (rev 01) 06:04.0 0607: 1524:1412 (rev 10) 06:04.1 0501: 1524:0530 (rev 01) 06:04.2 0805: 1524:0550 (rev 01) 06:04.3 0501: 1524:0520 (rev 01) 06:04.4 0501: 1524:0551 (rev 01) + lspci -v 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, 66MHz, medium devsel, latency 64 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00009000-00009fff Memory behind bridge: c0100000-c01fffff Prefetchable memory behind bridge: 00000000c8000000-00000000cff00000 Capabilities: [44] HyperTransport: MSI Mapping Capabilities: [b0] #0d [0000] 00:04.0 PCI bridge: ATI Technologies Inc Unknown device 5a36 (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=03, sec-latency=0 Capabilities: [50] Power Management version 3 Capabilities: [58] Express Root Port (Slot-) IRQ 0 Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+ Capabilities: [b0] #0d [0000] Capabilities: [b8] HyperTransport: MSI Mapping Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:05.0 PCI bridge: ATI Technologies Inc Unknown device 5a37 (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=05, sec-latency=0 Capabilities: [50] Power Management version 3 Capabilities: [58] Express Root Port (Slot-) IRQ 0 Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+ Capabilities: [b0] #0d [0000] Capabilities: [b8] HyperTransport: MSI Mapping Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 217 Memory at c0004000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 217 Memory at c0005000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80) (prog-if 20 [EHCI]) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 217 Memory at c0006000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: 66MHz, medium devsel I/O ports at 8400 [size=16] Memory at fed00000 (32-bit, non-prefetchable) [size=1K] Capabilities: [b0] HyperTransport: MSI Mapping 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI (rev 80) (prog-if 82 [Master PriP]) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 209 I/O ports at <ignored> I/O ports at <ignored> I/O ports at <ignored> I/O ports at <ignored> I/O ports at 8410 [size=16] Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- 00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: slow devsel, IRQ 209 Memory at c0000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, 66MHz, medium devsel, latency 0 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, medium devsel, latency 64 Bus: primary=00, secondary=06, subordinate=08, sec-latency=64 I/O behind bridge: 0000a000-0000afff Memory behind bridge: c0200000-c02fffff Prefetchable memory behind bridge: 50000000-51ffffff 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] #0f [0010] 01:05.0 VGA compatible controller: ATI Technologies Inc RS482 [Radeon Xpress 200M] (prog-if 00 [VGA]) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, 66MHz, medium devsel, latency 66, IRQ 11 Memory at c8000000 (32-bit, prefetchable) [size=128M] I/O ports at 9000 [size=256] Memory at c0100000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at c0120000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 06:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, medium devsel, latency 64, IRQ 50 I/O ports at a000 [size=256] Memory at c0210000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 06:02.0 Ethernet controller: Atheros Communications, Inc. AR5005G 802.11abg NIC (rev 01) Subsystem: AMBIT Microsystem Corp. Unknown device 0418 Flags: bus master, medium devsel, latency 168, IRQ 233 Memory at c0200000 (32-bit, non-prefetchable) [size=64K] Capabilities: [44] Power Management version 2 06:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, medium devsel, latency 168, IRQ 177 Memory at c0211000 (32-bit, non-prefetchable) [size=4K] Bus: primary=06, secondary=07, subordinate=07, sec-latency=176 Memory window 0: 50000000-51fff000 (prefetchable) Memory window 1: 52000000-53fff000 I/O window 0: 0000a400-0000a4ff I/O window 1: 0000a800-0000a8ff 16-bit legacy interface ports at 0001 06:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller (rev 01) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, medium devsel, latency 64, IRQ 11 Memory at c0210400 (32-bit, non-prefetchable) [size=128] Capabilities: [80] Power Management version 2 06:04.2 Class 0805: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller (rev 01) (prog-if 01) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, medium devsel, latency 64, IRQ 225 Memory at c0210800 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 06:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology Inc: (rev 01) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: bus master, medium devsel, latency 64, IRQ 11 Memory at c0210c00 (32-bit, non-prefetchable) [size=128] Capabilities: [80] Power Management version 2 06:04.4 FLASH memory: ENE Technology Inc Unknown device 0551 (rev 01) Subsystem: Acer Incorporated [ALI] Unknown device 009f Flags: medium devsel, IRQ 255 Memory at c0210100 (32-bit, non-prefetchable) [disabled] [size=256] Capabilities: [80] Power Management version 2 + lspci -n -vvv 00:00.0 0600: 1002:5950 (rev 10) Subsystem: 1025:009f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 00:01.0 0604: 1002:5a3f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00009000-00009fff Memory behind bridge: c0100000-c01fffff Prefetchable memory behind bridge: 00000000c8000000-00000000cff00000 Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [44] HyperTransport: MSI Mapping Capabilities: [b0] #0d [0000] 00:04.0 0604: 1002:5a36 Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=03, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express Root Port (Slot-) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x1 Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+ Address: fee00000 Data: 40c1 Capabilities: [b0] #0d [0000] Capabilities: [b8] HyperTransport: MSI Mapping Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:05.0 0604: 1002:5a37 Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=04, subordinate=05, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express Root Port (Slot-) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x1 Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+ Address: fee00000 Data: 40c9 Capabilities: [b0] #0d [0000] Capabilities: [b8] HyperTransport: MSI Mapping Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:13.0 0c03: 1002:4374 (rev 80) (prog-if 10) Subsystem: 1025:009f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 217 Region 0: Memory at c0004000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:13.1 0c03: 1002:4375 (rev 80) (prog-if 10) Subsystem: 1025:009f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 217 Region 0: Memory at c0005000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:13.2 0c03: 1002:4373 (rev 80) (prog-if 20) Subsystem: 1025:009f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 217 Region 0: Memory at c0006000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:14.0 0c05: 1002:4372 (rev 83) Subsystem: 1025:009f Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Region 0: I/O ports at 8400 [size=16] Region 1: Memory at fed00000 (32-bit, non-prefetchable) [size=1K] Capabilities: [b0] HyperTransport: MSI Mapping 00:14.1 0101: 1002:4376 (rev 80) (prog-if 82) Subsystem: 1025:009f Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 209 Region 0: I/O ports at <ignored> Region 1: I/O ports at <ignored> Region 2: I/O ports at <ignored> Region 3: I/O ports at <ignored> Region 4: I/O ports at 8410 [size=16] Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 00:14.2 0403: 1002:437b (rev 01) Subsystem: 1025:009f Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 209 Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 00:14.3 0601: 1002:4377 (rev 80) Subsystem: 1025:009f Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:14.4 0604: 1002:4371 (rev 80) (prog-if 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=06, subordinate=08, sec-latency=64 I/O behind bridge: 0000a000-0000afff Memory behind bridge: c0200000-c02fffff Prefetchable memory behind bridge: 50000000-51ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- 00:18.0 0600: 1022:1100 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 00:18.1 0600: 1022:1101 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.2 0600: 1022:1102 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.3 0600: 1022:1103 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Capabilities: [f0] #0f [0010] 01:05.0 0300: 1002:5975 Subsystem: 1025:009f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at c8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 9000 [size=256] Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at c0120000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 06:01.0 0200: 10ec:8139 (rev 10) Subsystem: 1025:009f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 50 Region 0: I/O ports at a000 [size=256] Region 1: Memory at c0210000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 06:02.0 0200: 168c:001a (rev 01) Subsystem: 1468:0418 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 233 Region 0: Memory at c0200000 (32-bit, non-prefetchable) [size=64K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 06:04.0 0607: 1524:1412 (rev 10) Subsystem: 1025:009f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size: 128 bytes Interrupt: pin A routed to IRQ 177 Region 0: Memory at c0211000 (32-bit, non-prefetchable) [size=4K] Bus: primary=06, secondary=07, subordinate=07, sec-latency=176 Memory window 0: 50000000-51fff000 (prefetchable) Memory window 1: 52000000-53fff000 I/O window 0: 0000a400-0000a4ff I/O window 1: 0000a800-0000a8ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 06:04.1 0501: 1524:0530 (rev 01) Subsystem: 1025:009f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (250ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 11 Region 0: Memory at c0210400 (32-bit, non-prefetchable) [size=128] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 06:04.2 0805: 1524:0550 (rev 01) (prog-if 01) Subsystem: 1025:009f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 18000ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 225 Region 0: Memory at c0210800 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 06:04.3 0501: 1524:0520 (rev 01) Subsystem: 1025:009f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (250ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 11 Region 0: Memory at c0210c00 (32-bit, non-prefetchable) [size=128] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 06:04.4 0501: 1524:0551 (rev 01) Subsystem: 1025:009f Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 255 Region 0: Memory at c0210100 (32-bit, non-prefetchable) [disabled] [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- + lsusb Bus 003 Device 001: ID 0000:0000 Bus 002 Device 002: ID 062a:0000 Creative Labs Bus 002 Device 001: ID 0000:0000 Bus 001 Device 002: ID 0402:5602 ALi Corp. Bus 001 Device 001: ID 0000:0000 + lsusb -v Bus 003 Device 001: ID 0000:0000 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0000 idProduct 0x0000 bcdDevice 2.06 iManufacturer 3 Linux 2.6.17-10-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:13.1 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 0 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Bus 002 Device 002: ID 062a:0000 Creative Labs Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x062a Creative Labs idProduct 0x0000 bcdDevice 0.00 iManufacturer 0 iProduct 0 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 34 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Devices bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 52 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) Bus 002 Device 001: ID 0000:0000 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0000 idProduct 0x0000 bcdDevice 2.06 iManufacturer 3 Linux 2.6.17-10-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:13.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 0 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0303 lowspeed power enable connect Device Status: 0x0003 Self Powered Remote Wakeup Enabled Bus 001 Device 002: ID 0402:5602 ALi Corp. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0402 ALi Corp. idProduct 0x5602 bcdDevice 1.00 iManufacturer 0 iProduct 1 USB2.0 Camera iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 101 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 1 Transfer Type Isochronous Synch Type None Usage Type Data wMaxPacketSize 0x0000 1x 0 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0000 1x 0 bytes bInterval 4 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 1 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 1 Transfer Type Isochronous Synch Type None Usage Type Data wMaxPacketSize 0x1400 3x 0 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0010 1x 16 bytes bInterval 4 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 2 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 1 Transfer Type Isochronous Synch Type None Usage Type Data wMaxPacketSize 0x1380 3x 896 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0010 1x 16 bytes bInterval 4 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 3 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 1 Transfer Type Isochronous Synch Type None Usage Type Data wMaxPacketSize 0x1300 3x 768 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0010 1x 16 bytes bInterval 4 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Bus 001 Device 001: ID 0000:0000 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 idVendor 0x0000 idProduct 0x0000 bcdDevice 2.06 iManufacturer 3 Linux 2.6.17-10-generic ehci_hcd iProduct 2 EHCI Host Controller iSerial 1 0000:00:13.2 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 12 Hub Descriptor: bLength 11 bDescriptorType 41 nNbrPorts 8 wHubCharacteristic 0x000a No power switching (usb 1.0) Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 0x00 PortPwrCtrlMask 0xff 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0503 highspeed power enable connect Port 5: 0000.0100 power Port 6: 0000.0100 power Port 7: 0000.0000 Port 8: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled + cat -v /proc/bus/usb/devices + cat -v /proc/pci cat: /proc/pci: No such file or directory + cat -v /proc/cmdline + cat -v /proc/uptime + cat -v /proc/devices + cat -v /proc/misc + cat -v /proc/filesystems + cat -v /proc/interrupts + cat -v /proc/iomem + cat -v /proc/ioports + cat -v /proc/dma + cat -v /proc/mtrr + cat -v /proc/partitions + cat -v /proc/mounts + cat -v /proc/swaps + cat -v /proc/meminfo + cat -v /proc/stat + cat -v /proc/apm cat: /proc/apm: No such file or directory and goes on with other 1300+ lines on modules, blacklists, etc. (but could not get it pasted here) END hsfdiag.txt ------------------------------------------------------------- "Marvin Stodolsky" To: discuss@xxxxxxxxxxxxx <marvin.stodolsky cc: ARinaldi@xxxxxxx @gmail.com> Subject: Re: Fw: Re2: Antonio, Italy, Ubuntu 6.06 / 6.10, kernel 2.6.15 / 2.6.17, HSF Conexant 02/03/2007 01:12 Antonio, The List Server only forwards PLAIN Text email, as viruses can be embedded in HTML or other more complex formats. Your sending in HTML was likely responsible for your mail's failure to be forwarded to the List. With respect to your specific modem problem, that will have to be solved by Linuxant MarvS scanModem maintainer On 3/1/07, Jacques Goldberg <Jacques.Goldberg@xxxxxxx> wrote: > Antonio, > I forward your problem to discuss@xxxxxxxxxxxxx > I am quite confused by your message and suggest a complete reset. > Download the most recent scanModem from > http://linmodems.technion.ac.il/packages > Run again, and send ModemData.txt to discuss@xxxxxxxxxxxxx with a copy > directly to me. > In addition, please report EXACTLY the COMPLETE name of the driver file > which you are trying to use. If you try to install again, make SURE to > have erased any earlier installation of any HSF driver. > > > FOLKS, > Please read this message. The author says that this thread never reached > the list (true in my archive at least). Please read all his stuff, not > only my answer. > The Saga starts in December 2006 with > http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04938.html > to which my reply was > http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04940.html > based on the following quote in ModemData.txt using scanModem update of: > 2006_November_07 > > "BEGIN > Modem or host audio card candidates have firmware information: > > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 0000:00:14.2 1002:437b 1025:009f 0403: ATI Technologies Inc: > Unknown device 437b > > Modem interrupt assignment and sharing: > 209: 15377 0 IO-APIC-level HDA Intel > > --- Bootup diagnositcs for card in PCI slot 0000:00:14.2 ---- > > === Finished modem firmware and bootup diagnostics section. === > === Next deducing cogent software === > > 1002:437b is a High Definition Audio card, possibly hosting a soft modem. > > For candidate modem in PCI bus: 0000:00:14.2 > Class 0403: 1002:437b 0403: ATI Technologies Inc: Unknown device 437b > Primary PCI_id 1002:437b > Subsystem PCI_id 1025:009f > Softmodem codec or Vendor from diagnostics: 14f1, a Conexant type, > from Archives: > > > > "END > > Thus all his efforts are based on the asumption that 1002:437b + > 1025:009f is a Coenxant device. >
