Thank you very much Mr. Marvin Stodolsky. Now my Agere Modem was work like a charm. Here is the output command : $cat /proc/asound/pcm 00-06: Si3054 Modem : Si3054 Modem : playback 1 : capture 1 00-02: ALC883 Analog : ALC883 Analog : capture 2 00-01: ALC883 Digital : ALC883 Digital : playback 1 00-00: ALC883 Analog : ALC883 Analog : playback 1 : capture 2 $aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: ALC883 Analog [ALC883 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC883 Digital [ALC883 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem] Subdevices: 0/1 Subdevice #0: subdevice #0 $slmodemd -c INDONESIA --alsa hw:0,6 Symbolic link `/dev/ttySL0` -> `/dev/pts/5` created. Modem `hw:0,6` created. TTY is `/dev/pts/5` Use `/dev/ttySL0` as modem device, Ctrl+C for termination. I have a question though, How can I inserted it within modprobe, so I don't have to repeat the command after reboot ? Once again, thank you very much Mr. Marvin Stodolsky. Cheers, jfdesign -----Original Message----- From: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] Sent: Monday, January 08, 2007 2:18 PM To: Jusuf Cc: DISCUSS@xxxxxxxxxxxxx Subject: Re: jfdesign, Indonesia Mandriva 2007.0 kernel 2.6.17-5mdv Jusuf With respect to the wvdial problem you will have to check the Mandiva list. The failure of he command: aplay -l | grep -i modem to display the modem shows that an ALSA update is needed to support the 0x11c13055 AgereSystems modem on the HDA audio card. Your compiling resources appear complete: make utility - /usr/bin/make Compiler version 4.1 kernel_headers base folder /lib/modules/2.6.17-5mdv/build Make a definition you will need later: $ HEADERS=/lib/modules/2.6.17-5mdv/build Check for validity with: $ ls $HEADERS should show files like: arch include lib scripts block init Makefile security crypto ipc mm sound drivers kabi_whitelist Module.symvers symsets-2.6.18-1.2798.fc6.tar.gz fs kernel net usr This definition does not survive a shutdown and must be redone upon reboot, when a new driver compiling is necessary. Then from http://www.alsa-project.org/ download the version 1.0.13 driver and lib packages. Make a folder, say alsa/. $ mkdir alsa Unpack both packages in the alsa/ folder $ cd alsa $ tar jxf PATH_to/alsa*.tar.bz2 will unpack both. The versions 1.0.13 and later have the recognition code for the 0x11c13055 chip. To compile the driver set, move into the driver folder: $ cd alsa-driver-1.0.13 Look around: $ ls $ make clean Do the configuration with with the following command on ONE LINE: $ ./configure --with-kernel=$HEADERS --with-build=$HEADERS --with-cards=hda-intel If the configuration is successful, the driver set will be compiled with: $ make Do nothing in the alsa-lib-1.0.13/ folder. But it is used during the compile. The new driver set is displayed by: $ ls modules and installed by $ su root $ make install THen reboot to have the new drivers used. Again run ./scanModem there should an device specification slmodemd -c YOUR_COUNTRY --alsa hw:0,N when N will be likely 1 or 6 And the modem should be shown by $ aplay -l Try the command: $ su root # slmodemd -c INDONESIA --alsa hw:0,N Hopefully its will announce port creation MarvS On 1/7/07, Jusuf <jusuf@xxxxxxxxxxxx> wrote: > Here is the new modemdata.txt with new scanmodem. > Still have no luck with Carrier Check = no within wvdialconf > Can you tell me where I can get wvdial for mdv2007? > Mine had serious problem with libwvstream.so cause I cannot get the 2007.0 > version, then I use 2006.0 version. > Instead of wvdial, can I just use kppp? > Thanks in advance. > > > Cheers, > > jfdesign > > -----Original Message----- > From: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] > Sent: Friday, January 05, 2007 4:36 PM > To: Jusuf > Cc: DISCUSS@xxxxxxxxxxxxx > Subject: Re: jfdesign, Indonesia Mandriva 2007.0 kernel 2.6.17-5mdv > > Jusuf > > RE: Code updated on: 2006_June_14 > --- > is to old. There may be more info if you use a current scanModem from > http://linmodems.technion.ac.il > Please send us the updated ModemData.txt > > RE: > But when dialing it always results nocarrier error. > The /etc/wvdial.conf should contain a line: > Carrier Check = no > > before dialing out with: > $ su root > $ wvdial > > MarvS > > > On 1/5/07, Jusuf <jusuf@xxxxxxxxxxxx> wrote: > > Querying slmodem ttySL0 with wvdialconf and kppp with no errors. > > > > But when dialing it always results nocarrier error. > > > > > > > > Please advice, and thanks in advance. > > > > > > > > Cheers, > > > > > > > > jfdesign > > > > > > > > > >