Jos The potential driver is snd-hda-intel + its dependent driver set. One problem is the driver set now on your System does not have the recognition code for the Agere softmodem chip, Vendor Id: 0x11c11040. Thus the driver set will have to be compiled and installed. Depending on your kernel, one of kernel-devel-2.6.18-1.2798.fc6.i686.rpm kernel-devel-2.6.18-1.2798.fc6.i386.rpm must be installed to complete your compiling support. If may be available on your install CDs or alternatively at a fedora mirror like ftp://ftp.linux.ncsu.edu/pub/fedora/linux/core/6/i386/os/Fedora The following should suffice if you kernel is for i686 as contrasted to the more general i386: ftp://ftp.linux.ncsu.edu/pub/fedora/linux/core/6/i386/os/Fedora/RPMS/kernel-devel-2.6.18-1.2798.fc6.i686.rpm it will be installed to /usr/src/kernels/2.6.18-1.2798.fc6-i686 (or i386) Make a definition you will need later: $ HEADERS=/usr/src/kernels/2.6.18-1.2798.fc6-i686 Check for validity with: $ ls $HEADERS should show: arch include lib scripts block init Makefile security crypto ipc mm sound drivers kabi_whitelist Module.symvers symsets-2.6.18-1.2798.fc6.tar.gz fs kernel net usr This definition does not survive a shutdown and must be redone upon reboot, when a new driver compiling is necessary. Then from http://www.alsa-project.org/ the version 1.0.14rc1 driver and lib packages. Make a folder, say alsa/. $ mkdir alsa Unpack both packages in the alsa/ folder $ tar jxf alsa*.tar.bz2 will unpack both. The versions 1.0.13 and later have the recognition code for the 0x11c11040 chip. To compile the driver set, move into the driver folder: $ cd alsa-driver-1.0.14rc1 Look around: $ ls $ make clean Do the configuration with with the following command on ONE LINE: $ ./configure --with-kernel=$HEADERS --with-build=$HEADERS --with-cards=hda-intel If the configuration is successful, the driver set will be compiled with: $ make Do nothing in the alsa-lib-1.0.14rc1/ folder. But it is used during the compile. The new driver set is displayed by: $ ls modules and installed by $ su root $ sudo make install THen reboot to have the new drivers used. Again run ./scanModem This time rather than slmodemd -c YOUR_COUNTRY --alsa there will be added device specification slmodemd -c YOUR_COUNTRY --alsa hw:0,N when N will be likely 1 or 6 Try the commands: $ su root # slmodemd -c NETHERLANDS --alsa hw:0,N Hopefully its will announce port creation Lajos is woking on this same problem, and we have reported it to the ALSA organization. But we as yet not had a success with the Agere softmodem chip, Vendor Id: 0x11c11040. Do send me us the new ModemData.txt Also do: $ cp -a /proc/asound vos $ tar cfz vos.tgz vos/ Send the vos.tgz to both Lajos and me. Sunday afternoon I will be begin a two week trip and will rarely be on line until Sept.9, if at all. MarvS scanModem maintainer On 12/23/06, Jos Vos <jos@xxxxxx> wrote:
Hi, Here the ModemData.txt file for a Compal HGL30 laptop (Intel barebone), because the ModemData.txt file says I should send it to the list :-). I didn't succeed to get the modem working: I tried slmodemd and I can issue AT commands to the device (and get a response), but when dialing, I immediately get "NO CARRIER" and slmodem then says: error: cannot set channels for playback: Invalid argument Any hints are welcome. ============================================================================= Only plain text email is forwarded by the DISCUSS@xxxxxxxxxxxxx List Server. Do use the following as the email Subject Line: SomeName, YourCountry Fedora Core release 6 (Zod) Kernel kernel 2.6.18-1.2868.fc6 This will alert cogent experts, and distinguish cases in the Archives. YourCountry will enable Country Code guidance. Occassionally responses are blocked by an Internet Provider mail filters. So in a day, also check the Archived responses at http://www.linmodems.org . Local Linux experts can be found through: http://www.linux.org/groups/index.html -------------------------- System information ---------------------------- Fedora Core release 6 (Zod) Kernel Linux version 2.6.18-1.2868.fc6 (brewbuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Fri Dec 15 17:31:29 EST 2006 scanModem update of: 2006_December_20 USB modem not detected by lsusb Modem or host audio card candidates have firmware information: PCI slot PCI ID SubsystemID Name ---------- --------- --------- -------------- 00:1b.0 8086:27d8 14c0:0021 Audio device: Intel Corporation 82801G Modem interrupt assignment and sharing: 58: 164551 IO-APIC-level HDA Intel --- Bootup diagnositcs for card in PCI slot 00:1b.0 ---- ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 58 PCI: Setting latency timer of device 0000:00:1b.0 to 64 ACPI: PCI interrupt for device 0000:00:1b.0 disabled PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100006, writing 100000) PCI: Enabling device 0000:00:1b.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 58 PCI: Setting latency timer of device 0000:00:1b.0 to 64 ACPI: PCI interrupt for device 0000:00:1b.0 disabled PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100006, writing 100000) PCI: Enabling device 0000:00:1b.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 58 PCI: Setting latency timer of device 0000:00:1b.0 to 64 The PCI slot 00:1b.0 of the modem card may be disabled early in a bootup process, but then enabled later. If modem drivers load but the modem is not responsive, read Bootup.txt about possible fixes. Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx if help is needed. === Finished modem firmware and bootup diagnostics section. === === Next deducing cogent software === 8086:27d8 is a High Definition Audio card, possibly hosting a soft modem. A candidate driver could not be identified. For candidate modem in PCI bus: 00:1b.0 Class 0403: 8086:27d8 Audio device: Intel Corporation 82801G Primary PCI_id 8086:27d8 Subsystem PCI_id 14c0:0021 Softmodem codec or Vendor from diagnostics: 11c1, an AgereSystems type. from Archives: This is a NEW softmodem case! Please send the output ModemData.txt to DISCUSS@xxxxxxxxxxxxx , even if further assistance is not needed. It will enrich the Archive and help others! ------------------------------------------- Lacking a dsp (digital signal processing) chip, the modem is a software intensive or "softmodem" type. Its primary controller manages the traffic with the CPU. But the software needed is specified in the Subsystem. ----------------------------------------- Support type needed or chipset: slmodemd An ALSA (Advanced Linux Sound Architecture) modem driver: provides Low Level support enabling contact with the modem hardware. For all BUT Conexant chip soft modems (using hsfmodem software) complementary High Level support is through a Smartlink utility: slmodemd Download from http://linmodems.technion.ac.il/packages/smartlink/ the package SLMODEMD.gcc4.tar.gz having a compiled slmodemd. Unpack under Linux with: $ tar zxf SLMODEMD.gcc4.tar.gz and read instructions therein. But briefly, the modem is setup with command: slmodemd -c YOUR_COUNTRY --alsa reporting dynamic creation of ports: /dev/ttySL0 --> /dev/pts/N , with N some number Read Smartlink.txt and Modem/YourSystem.txt for follow through guidance. The diagnostic outputs for this softmodem section have their raw information in folders and text files under /proc/asound/ which you can browse. The information is from files: /proc/asound/pcm ------------------------------- 00-02: ALC883 Digital : ALC883 Digital : playback 1 00-01: ALC883 Analog : ALC883 Analog : capture 2 00-00: ALC883 Analog : ALC883 Analog : playback 1 : capture 2 /proc/asound/modules ------------------------------- 0 snd_hda_intel /proc/asound/card0/codec#1 ------------------------------- Codec: Generic 11c1 ID 1040 Address: 1 Vendor Id: 0x11c11040 Subsystem Id: 0x11c10001 Revision Id: 0x100200 ------------------------------- Current support status of HDA cards is: Vendor IDs Chip maker Support type ---------- ---------- ------------- 0x14f12bfa Conexant hsfmodem , not slmodemd compatible 0x11c13026 AgereSystems snd-hda-intel, slmodemd supported 0x11c11040 AgereSystems " " , patch needed 0x11c13055 AgereSystems " " , " 0x163c3055 Smartlink " " , " 0x163c3155 " " " , " 0x10573055 Motorola " " , " 0x10573155 " " " , "" as of October 2006. and from the command: aplay -l | grep -i modem ----------------end Softmodem section -------------- Writing Intel.txt Writing Smartlink.txt ============ end Smartlink section ===================== Completed candidate modem analyses. The base of the UDEV device file system is: /dev/.udev Versions adequately match for the compiler installed: 4.1.1 and the compiler used in kernel assembly: 4.1.1 Kernel-header resources needed for compiling are not manifestly ready! If compiling is necessary packages must be installed, providing: kernel-source-2.6.18-1.2868.fc6 Checking pppd properties: -r-xr-xr-x 1 root root 312492 Dec 1 13:51 /usr/sbin/pppd In case of an "error 17" "serial loopback" problem, see: http://phep2.technion.ac.il/linmodems/archive-sixth/msg02637.html To enable dialout without Root permission do: $ su - root (not for Ubuntu) chmod a+x /usr/sbin/pppd or under Ubuntu related Linuxes chmod a+x /usr/sbin/pppd Checking settings of: /etc/ppp/options lock Read Modem/YourSystem.txt concerning other COMM channels: eth0 Which can interfere with Browser naviagation. Don't worry about the following, it is for the experts should trouble shooting be necessary. ========================================================== Checking for modem support lines: -------------------------------------- /device/modem symbolic link: slmodemd created symbolic link /dev/ttySL0: Within /etc/udev/ files: /etc/udev/rules.d/50-udev.rules:KERNEL=="modems/mwave*", NAME="%k", GROUP="uucp", MODE="0660" Within /etc/modprobe.conf files: Within any ancient /etc/devfs files: Within ancient kernel 2.4.n /etc/module.conf files: --------- end modem support lines -------- ============================================================================= -- -- Jos Vos <jos@xxxxxx> -- X/OS Experts in Open Systems BV | Phone: +31 20 6938364 -- Amsterdam, The Netherlands | Fax: +31 20 6948204