Hi Alex, i got some more output and i am getting closer: i installed mythbuntu as vm and tested with both cards and with one only card via passthrough. One card assembled works nice, two cards assembled gives me an error: there is no frontend0 found in '/dev/dvb/adapter0/frontend0'. A look into both dmesg and a diff shows, that there is a change in the IRQ Number (10->11) and the eeprom of the device couldnt be read. I am not able to take a conclusion of that - maybe you can give me one more hint. I will try tomorrow to use both devices on 'bare metal' to make sure it is working in this configuration. More infos will come. bye for now, DP ------------------------------------------------------------------------------- lspci on mythubuntu vm: virtual-machine:~$ lspci -vvv -s 00:06.0 00:06.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01) Subsystem: Technotrend Systemtechnik GmbH S2-3200 Physical Slot: 6 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (3750ns min, 9500ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at f2031000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: budget_ci dvb Kernel modules: budget-ci virtual-machine:~$ lspci -vvv -s 00:07.0 00:07.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01) Subsystem: Technotrend Systemtechnik GmbH S2-3200 Physical Slot: 7 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (3750ns min, 9500ns max) Interrupt: pin A routed to IRQ 10 Region 0: Memory at f2032000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: budget_ci dvb Kernel modules: budget-ci ------------------------------------------------------------------------------- lsmod on mythubuntu vm: virtual-machine:~$ lsmod Module Size Used by lnbp21 2338 0 stb6100 7128 0 stb0899 36531 0 rc_tt_1500 1310 0 snd_intel8x0 31371 0 snd_ac97_codec 125227 1 snd_intel8x0 ac97_bus 1474 1 snd_ac97_codec snd_pcm 89104 2 snd_intel8x0,snd_ac97_codec snd_seq_midi 5932 0 ir_lirc_codec 3888 0 lirc_dev 11209 1 ir_lirc_codec snd_rawmidi 22207 1 snd_seq_midi ir_sony_decoder 2381 0 snd_seq_midi_event 7291 1 snd_seq_midi ir_jvc_decoder 2442 0 snd_seq 57512 2 snd_seq_midi,snd_seq_midi_event ir_rc6_decoder 3018 0 snd_timer 23850 2 snd_pcm,snd_seq snd_seq_device 6912 3 snd_seq_midi,snd_rawmidi,snd_seq joydev 11395 0 ir_rc5_decoder 2474 0 ir_nec_decoder 2442 0 budget_ci 22413 0 snd 64181 7 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer, snd_seq_device budget_core 9552 1 budget_ci dvb_core 105239 2 budget_ci,budget_core saa7146 17480 2 budget_ci,budget_core usbhid 42030 0 psmouse 62080 0 soundcore 1240 1 snd lp 10201 0 ttpci_eeprom 1953 1 budget_core i2c_piix4 10047 0 ir_core 16906 10 rc_tt_1500,ir_lirc_codec,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder, ir_rc5_decoder,ir_nec_decoder,budget_ci serio_raw 4910 0 snd_page_alloc 8588 2 snd_intel8x0,snd_pcm virtio_balloon 4477 0 hid 84710 1 usbhid parport 37032 1 lp virtio_blk 5622 3 virtio_net 13671 0 floppy 65299 0 virtio_pci 7100 0 virtio_ring 6098 4 virtio_balloon,virtio_blk,virtio_net, virtio_pci virtio 4912 4 virtio_balloon,virtio_blk,virtio_net, virtio_pci ------------------------------------------------------------------------------- dmesg with 2 cards in mythbuntu vm - NOT WORKING: virtual-machine:/$ dmesg [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.35-25-generic (buildd@crested) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #44-Ubuntu SMP Fri Jan 21 17:40:44 UTC 2011 (Ubuntu 2.6.35-25.44-generic 2.6.35.10) [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-25-generic root=UUID=58eb9e81-3bc6-4266-ad52-8030a004f4ba ro quiet splash [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable) [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfffb000 (usable) [ 0.000000] BIOS-e820: 00000000dfffb000 - 00000000e0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fffbc000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000132300000 (usable) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.4 present. [ 0.000000] e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] No AGP bridge found [ 0.000000] last_pfn = 0x132300 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: write-back [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 00E0000000 mask FFE0000000 uncachable [ 0.000000] 1 disabled [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] PAT not supported by CPU. [ 0.000000] last_pfn = 0xdfffb max_arch_pfn = 0x400000000 [ 0.000000] e820 update range: 0000000000001000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] Scanning 1 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 000000000009f000 (usable) [ 0.000000] modified: 000000000009f000 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 00000000dfffb000 (usable) [ 0.000000] modified: 00000000dfffb000 - 00000000e0000000 (reserved) [ 0.000000] modified: 00000000fffbc000 - 0000000100000000 (reserved) [ 0.000000] modified: 0000000100000000 - 0000000132300000 (usable) [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] found SMP MP-table at [ffff8800000f8870] f8870 [ 0.000000] init_memory_mapping: 0000000000000000-00000000dfffb000 [ 0.000000] 0000000000 - 00dfe00000 page 2M [ 0.000000] 00dfe00000 - 00dfffb000 page 4k [ 0.000000] kernel direct mapping tables up to dfffb000 @ 16000-1c000 [ 0.000000] init_memory_mapping: 0000000100000000-0000000132300000 [ 0.000000] 0100000000 - 0132200000 page 2M [ 0.000000] 0132200000 - 0132300000 page 4k [ 0.000000] kernel direct mapping tables up to 132300000 @ 1a000-21000 [ 0.000000] RAMDISK: 37572000 - 37ff0000 [ 0.000000] ACPI: RSDP 00000000000f8820 00014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 00000000dfffdd90 00034 (v01 BOCHS BXPCRSDT 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 00000000dffffe70 00074 (v01 BOCHS BXPCFACP 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 00000000dfffdf30 01EC4 (v01 BXPC BXDSDT 00000001 INTL 20100528) [ 0.000000] ACPI: FACS 00000000dffffe00 00040 [ 0.000000] ACPI: SSDT 00000000dfffdef0 00037 (v01 BOCHS BXPCSSDT 00000001 BXPC 00000001) [ 0.000000] ACPI: APIC 00000000dfffde10 00072 (v01 BOCHS BXPCAPIC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 00000000dfffddd0 00038 (v01 BOCHS BXPCHPET 00000001 BXPC 00000001) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-0000000132300000 [ 0.000000] Initmem setup node 0 0000000000000000-0000000132300000 [ 0.000000] NODE_DATA [0000000100000000 - 0000000100004fff] [ 0.000000] kvm-clock: Using msrs 12 and 11 [ 0.000000] kvm-clock: cpu 0, msr 0:1aeb901, boot clock [ 0.000000] [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880100200000-ffff8801041fffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00132300 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x000dfffb [ 0.000000] 0: 0x00100000 -> 0x00132300 [ 0.000000] On node 0 totalpages: 1122954 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3927 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 899123 pages, LIFO batch:31 [ 0.000000] Normal zone: 2811 pages used for memmap [ 0.000000] Normal zone: 202757 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0xb008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ5 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ10 used by override. [ 0.000000] ACPI: IRQ11 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] early_res array is doubled to 64 at [1c000 - 1c7ff] [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000dfffb000 - 00000000e0000000 [ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000fffbc000 [ 0.000000] PM: Registered nosave memory: 00000000fffbc000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:1ffbc000) [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880001e00000 s91520 r8192 d23168 u2097152 [ 0.000000] pcpu-alloc: s91520 r8192 d23168 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] kvm-clock: cpu 0, msr 0:1e15901, primary cpu clock [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1105807 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-25-generic root=UUID=58eb9e81-3bc6-4266-ad52-8030a004f4ba ro quiet splash [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] Subtract (49 early reservations) [ 0.000000] #1 [0001000000 - 0001d17114] TEXT DATA BSS [ 0.000000] #2 [0037572000 - 0037ff0000] RAMDISK [ 0.000000] #3 [0001d18000 - 0001d18071] BRK [ 0.000000] #4 [000009f000 - 00000f8870] BIOS reserved [ 0.000000] #5 [00000f8870 - 00000f8880] MP-table mpf [ 0.000000] #6 [00000f8988 - 0000100000] BIOS reserved [ 0.000000] #7 [00000f8880 - 00000f8988] MP-table mpc [ 0.000000] #8 [0000010000 - 0000012000] TRAMPOLINE [ 0.000000] #9 [0000012000 - 0000016000] ACPI WAKEUP [ 0.000000] #10 [0000016000 - 000001a000] PGTABLE [ 0.000000] #11 [000001a000 - 000001c000] PGTABLE [ 0.000000] #12 [0100000000 - 0100005000] NODE_DATA [ 0.000000] #13 [0001d18080 - 0001d19080] BOOTMEM [ 0.000000] #14 [0001d17140 - 0001d17488] BOOTMEM [ 0.000000] #15 [0100005000 - 0100006000] BOOTMEM [ 0.000000] #16 [0100006000 - 0100007000] BOOTMEM [ 0.000000] #17 [0100200000 - 0104200000] MEMMAP 0 [ 0.000000] #18 [0001d174c0 - 0001d17640] BOOTMEM [ 0.000000] #19 [0001d19080 - 0001d31080] BOOTMEM [ 0.000000] #20 [0001d31080 - 0001d37080] BOOTMEM [ 0.000000] #21 [0001d38000 - 0001d39000] BOOTMEM [ 0.000000] #22 [0001d17640 - 0001d17681] BOOTMEM [ 0.000000] #23 [0001d176c0 - 0001d17703] BOOTMEM [ 0.000000] #24 [0001d17740 - 0001d17900] BOOTMEM [ 0.000000] #25 [0001d17900 - 0001d17968] BOOTMEM [ 0.000000] #26 [0001d17980 - 0001d179e8] BOOTMEM [ 0.000000] #27 [0001d17a00 - 0001d17a68] BOOTMEM [ 0.000000] #28 [0001d17a80 - 0001d17ae8] BOOTMEM [ 0.000000] #29 [0001d17b00 - 0001d17b68] BOOTMEM [ 0.000000] #30 [0001d17b80 - 0001d17be8] BOOTMEM [ 0.000000] #31 [0001d17c00 - 0001d17c68] BOOTMEM [ 0.000000] #32 [0001d17c80 - 0001d17ca0] BOOTMEM [ 0.000000] #33 [0001d17cc0 - 0001d17ce0] BOOTMEM [ 0.000000] #34 [0001d17d00 - 0001d17d6a] BOOTMEM [ 0.000000] #35 [0001d17d80 - 0001d17dea] BOOTMEM [ 0.000000] #36 [0001e00000 - 0001e1e000] BOOTMEM [ 0.000000] #37 [0001d17e00 - 0001d17e08] BOOTMEM [ 0.000000] #38 [0001d17e40 - 0001d17e48] BOOTMEM [ 0.000000] #39 [0001d17e80 - 0001d17e84] BOOTMEM [ 0.000000] #40 [0001d17ec0 - 0001d17ec8] BOOTMEM [ 0.000000] #41 [0001d37080 - 0001d371d0] BOOTMEM [ 0.000000] #42 [0001d17f00 - 0001d17f80] BOOTMEM [ 0.000000] #43 [0001d17f80 - 0001d18000] BOOTMEM [ 0.000000] #44 [0001d39000 - 0001d41000] BOOTMEM [ 0.000000] #45 [0001e1e000 - 0005e1e000] BOOTMEM [ 0.000000] #46 [0001d41000 - 0001d61000] BOOTMEM [ 0.000000] #47 [0001d61000 - 0001da1000] BOOTMEM [ 0.000000] #48 [000001c800 - 0000024800] BOOTMEM [ 0.000000] Memory: 4335812k/5016576k available (5714k kernel code, 524760k absent, 156004k reserved, 5377k data, 908k init) [ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] Verbose stalled-CPUs detection is disabled. [ 0.000000] NR_IRQS:4352 nr_irqs:256 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 45875200 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] hpet clockevent registered [ 0.000000] Detected 3324.608 MHz processor. [ 0.010000] Calibrating delay loop (skipped) preset value.. 6649.21 BogoMIPS (lpj=33246080) [ 0.010000] pid_max: default: 32768 minimum: 301 [ 0.010000] Security Framework initialized [ 0.010000] AppArmor: AppArmor initialized [ 0.010000] Yama: becoming mindful. [ 0.010000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.010000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.010000] Mount-cache hash table entries: 256 [ 0.010000] Initializing cgroup subsys ns [ 0.010000] Initializing cgroup subsys cpuacct [ 0.010000] Initializing cgroup subsys memory [ 0.010000] Initializing cgroup subsys devices [ 0.010000] Initializing cgroup subsys freezer [ 0.010000] Initializing cgroup subsys net_cls [ 0.010012] mce: CPU supports 10 MCE banks [ 0.010047] Performance Events: unsupported p6 CPU model 2 no PMU driver, software events only. [ 0.010186] SMP alternatives: switching to UP code [ 0.029027] Freeing SMP alternatives: 24k freed [ 0.029044] ACPI: Core revision 20100428 [ 0.030850] ftrace: converting mcount calls to 0f 1f 44 00 00 [ 0.030855] ftrace: allocating 22681 entries in 89 pages [ 0.040072] Setting APIC routing to flat [ 0.040985] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.040987] CPU0: Intel QEMU Virtual CPU version 0.12.5 stepping 03 [ 0.050000] Brought up 1 CPUs [ 0.050000] Total of 1 processors activated (6649.21 BogoMIPS). [ 0.050000] devtmpfs: initialized [ 0.050000] regulator: core version 0.5 [ 0.050000] Time: 19:42:48 Date: 02/19/11 [ 0.050000] NET: Registered protocol family 16 [ 0.050000] ACPI: bus type pci registered [ 0.050000] PCI: Using configuration type 1 for base access [ 0.050000] bio: create slab <bio-0> at 0 [ 0.050000] ACPI: EC: Look up EC in DSDT [ 0.050000] ACPI: Interpreter enabled [ 0.050000] ACPI: (supports S0 S3 S4 S5) [ 0.050000] ACPI: Using IOAPIC for interrupt routing [ 0.050000] ACPI: No dock devices found. [ 0.050000] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug [ 0.050000] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.050000] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored) [ 0.050000] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored) [ 0.050000] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored) [ 0.050000] pci_root PNP0A03:00: host bridge window [mem 0xe0000000-0xfebfffff] (ignored) [ 0.050000] pci 0000:00:01.1: reg 20: [io 0xc000-0xc00f] [ 0.050000] pci 0000:00:01.2: reg 20: [io 0xc020-0xc03f] [ 0.050000] pci 0000:00:01.3: quirk: [io 0xb000-0xb03f] claimed by PIIX4 ACPI [ 0.050000] pci 0000:00:01.3: quirk: [io 0xb100-0xb10f] claimed by PIIX4 SMB [ 0.050925] pci 0000:00:02.0: reg 10: [mem 0xf0000000-0xf1ffffff pref] [ 0.051702] pci 0000:00:02.0: reg 14: [mem 0xf2000000-0xf2000fff] [ 0.054739] pci 0000:00:02.0: reg 30: [mem 0xf2010000-0xf201ffff pref] [ 0.054917] pci 0000:00:03.0: reg 10: [io 0xc040-0xc05f] [ 0.054942] pci 0000:00:03.0: reg 14: [mem 0xf2020000-0xf2020fff] [ 0.055015] pci 0000:00:03.0: reg 30: [mem 0xf2028000-0xf202ffff pref] [ 0.055159] pci 0000:00:04.0: reg 10: [io 0xc400-0xc7ff] [ 0.055181] pci 0000:00:04.0: reg 14: [io 0xc800-0xc8ff] [ 0.055360] pci 0000:00:05.0: reg 10: [io 0xc900-0xc93f] [ 0.055383] pci 0000:00:05.0: reg 14: [mem 0xf2030000-0xf2030fff] [ 0.055858] pci 0000:00:06.0: reg 10: [mem 0xf2031000-0xf2031fff] [ 0.056422] pci 0000:00:07.0: reg 10: [mem 0xf2032000-0xf2032fff] [ 0.056672] pci 0000:00:08.0: reg 10: [io 0xc940-0xc95f] [ 0.056931] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.061318] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11) [ 0.061403] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11) [ 0.070090] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11) [ 0.080151] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11) [ 0.080335] ACPI: PCI Interrupt Link [LNKS] (IRQs 9) *0 [ 0.080438] HEST: Table is not found! [ 0.080836] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none [ 0.080845] vgaarb: loaded [ 0.081258] SCSI subsystem initialized [ 0.081547] libata version 3.00 loaded. [ 0.081691] usbcore: registered new interface driver usbfs [ 0.081720] usbcore: registered new interface driver hub [ 0.081790] usbcore: registered new device driver usb [ 0.082091] ACPI: WMI: Mapper loaded [ 0.082103] PCI: Using ACPI for IRQ routing [ 0.082113] PCI: pci_cache_line_size set to 64 bytes [ 0.082524] reserve RAM buffer: 000000000009f000 - 000000000009ffff [ 0.082534] reserve RAM buffer: 00000000dfffb000 - 00000000dfffffff [ 0.082537] reserve RAM buffer: 0000000132300000 - 0000000133ffffff [ 0.082834] NetLabel: Initializing [ 0.082841] NetLabel: domain hash size = 128 [ 0.082843] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.082876] NetLabel: unlabeled traffic allowed by default [ 0.082978] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.083025] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.083033] hpet0: 3 comparators, 64-bit 100.000000 MHz counter [ 0.090042] Switching to clocksource kvm-clock [ 0.103915] AppArmor: AppArmor Filesystem Enabled [ 0.103933] pnp: PnP ACPI init [ 0.103954] ACPI: bus type pnp registered [ 0.104560] pnp: PnP ACPI: found 6 devices [ 0.104562] ACPI: ACPI bus type pnp unregistered [ 0.110143] pci_bus 0000:00: resource 0 [io 0x0000-0xffff] [ 0.110145] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff] [ 0.110169] NET: Registered protocol family 2 [ 0.110341] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.111788] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.115247] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.115687] TCP: Hash tables configured (established 524288 bind 65536) [ 0.115689] TCP reno registered [ 0.115699] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.115776] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.115926] NET: Registered protocol family 1 [ 0.115943] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 0.115977] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 0.115994] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 0.116056] pci 0000:00:02.0: Boot video device [ 0.116106] PCI: CLS 0 bytes, default 64 [ 0.116125] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.116128] Placing 64MB software IO TLB between ffff880001e1e000 - ffff880005e1e000 [ 0.116130] software IO TLB at phys 0x1e1e000 - 0x5e1e000 [ 0.116322] Scanning for low memory corruption every 60 seconds [ 0.116468] audit: initializing netlink socket (disabled) [ 0.116479] type=2000 audit(1298144570.110:1): initialized [ 0.126217] Trying to unpack rootfs image as initramfs... [ 0.142677] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.151052] VFS: Disk quotas dquot_6.5.2 [ 0.151097] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.151540] fuse init (API version 7.14) [ 0.151604] msgmni has been set to 8468 [ 0.161418] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.161425] io scheduler noop registered [ 0.161427] io scheduler deadline registered [ 0.161451] io scheduler cfq registered (default) [ 0.161520] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.161535] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.161658] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.161666] ACPI: Power Button [PWRF] [ 0.161924] ACPI: acpi_idle registered with cpuidle [ 0.162537] ERST: Table is not found! [ 0.162652] Linux agpgart interface v0.103 [ 0.162665] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.162824] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.163676] brd: module loaded [ 0.163998] loop: module loaded [ 0.164118] ata_piix 0000:00:01.1: version 2.13 [ 0.164193] ata_piix 0000:00:01.1: setting latency timer to 64 [ 0.164346] scsi0 : ata_piix [ 0.170137] scsi1 : ata_piix [ 0.170170] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc000 irq 14 [ 0.170171] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc008 irq 15 [ 0.170343] Fixed MDIO Bus: probed [ 0.170364] PPP generic driver version 2.4.2 [ 0.170396] tun: Universal TUN/TAP device driver, 1.6 [ 0.170398] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> [ 0.170474] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.170485] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.170492] uhci_hcd: USB Universal Host Controller Interface driver [ 0.170673] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 [ 0.170693] uhci_hcd 0000:00:01.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, high) -> IRQ 11 [ 0.170710] uhci_hcd 0000:00:01.2: setting latency timer to 64 [ 0.170717] uhci_hcd 0000:00:01.2: UHCI Host Controller [ 0.170752] uhci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1 [ 0.170828] uhci_hcd 0000:00:01.2: irq 11, io base 0x0000c020 [ 0.170952] hub 1-0:1.0: USB hub found [ 0.170958] hub 1-0:1.0: 2 ports detected [ 0.171038] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 0.171531] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.171536] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.171647] mice: PS/2 mouse device common for all mice [ 0.171848] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 0.172066] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0 [ 0.172138] rtc0: alarms up to one day, 114 bytes nvram, hpet irqs [ 0.172223] device-mapper: uevent: version 1.0.3 [ 0.172301] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@xxxxxxxxxx [ 0.180317] device-mapper: multipath: version 1.1.1 loaded [ 0.180323] device-mapper: multipath round-robin: version 1.0.0 loaded [ 0.190115] cpuidle: using governor ladder [ 0.190117] cpuidle: using governor menu [ 0.190299] TCP cubic registered [ 0.190392] NET: Registered protocol family 10 [ 0.190642] lo: Disabled Privacy Extensions [ 0.190756] NET: Registered protocol family 17 [ 0.190894] PM: Resume from disk failed. [ 0.190913] registered taskstats version 1 [ 0.191081] Magic number: 15:103:749 [ 0.191102] tty ttyS0: hash matches [ 0.191173] rtc_cmos 00:01: setting system clock to 2011-02-19 19:42:49 UTC (1298144569) [ 0.191178] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.191179] EDD information not available. [ 0.313957] Freeing initrd memory: 10744k freed [ 0.340473] ata2.01: NODEV after polling detection [ 0.340702] ata2.00: ATAPI: QEMU DVD-ROM, 0.12.5, max UDMA/100 [ 0.341057] ata2.00: configured for MWDMA2 [ 0.341454] scsi 1:0:0:0: CD-ROM QEMU QEMU DVD-ROM 0.12 PQ: 0 ANSI: 5 [ 0.342606] sr0: scsi3-mmc drive: 4x/4x xa/form2 tray [ 0.342611] Uniform CD-ROM driver Revision: 3.20 [ 0.342696] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 0.342739] sr 1:0:0:0: Attached scsi generic sg0 type 5 [ 0.342778] Freeing unused kernel memory: 908k freed [ 0.343102] Write protecting the kernel read-only data: 10240k [ 0.343207] Freeing unused kernel memory: 412k freed [ 0.343714] Freeing unused kernel memory: 1644k freed [ 0.367821] udev[66]: starting version 163 [ 0.490070] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 0.512672] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 [ 0.512698] virtio-pci 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, high) -> IRQ 10 [ 0.512727] virtio-pci 0000:00:03.0: setting latency timer to 64 [ 0.513104] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 [ 0.513106] virtio-pci 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, high) -> IRQ 10 [ 0.513124] virtio-pci 0000:00:05.0: setting latency timer to 64 [ 0.513305] virtio-pci 0000:00:08.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, high) -> IRQ 11 [ 0.513320] virtio-pci 0000:00:08.0: setting latency timer to 64 [ 0.517965] alloc irq_desc for 40 on node -1 [ 0.517967] alloc kstat_irqs on node -1 [ 0.517991] virtio-pci 0000:00:05.0: irq 40 for MSI/MSI-X [ 0.517992] alloc irq_desc for 41 on node -1 [ 0.517993] alloc kstat_irqs on node -1 [ 0.518006] virtio-pci 0000:00:05.0: irq 41 for MSI/MSI-X [ 0.532016] FDC 0 is a S82078B [ 0.564799] vda: vda1 vda2 < vda5 > [ 0.565988] alloc irq_desc for 42 on node -1 [ 0.565992] alloc kstat_irqs on node -1 [ 0.566037] virtio-pci 0000:00:03.0: irq 42 for MSI/MSI-X [ 0.566041] alloc irq_desc for 43 on node -1 [ 0.566043] alloc kstat_irqs on node -1 [ 0.566076] virtio-pci 0000:00:03.0: irq 43 for MSI/MSI-X [ 0.566080] alloc irq_desc for 44 on node -1 [ 0.566083] alloc kstat_irqs on node -1 [ 0.566117] virtio-pci 0000:00:03.0: irq 44 for MSI/MSI-X [ 0.672089] EXT4-fs (vda1): INFO: recovery required on readonly filesystem [ 0.672092] EXT4-fs (vda1): write access will be enabled during recovery [ 0.756882] EXT4-fs (vda1): orphan cleanup on readonly fs [ 0.756897] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524633 [ 0.756941] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524632 [ 0.756946] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524631 [ 0.756950] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524630 [ 0.756954] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524629 [ 0.756957] EXT4-fs (vda1): 5 orphan inodes deleted [ 0.756959] EXT4-fs (vda1): recovery complete [ 0.757648] JBD: barrier-based sync failed on vda1-8 - disabling barriers [ 0.775610] EXT4-fs (vda1): mounted filesystem with ordered data mode. Opts: (null) [ 1.065716] Adding 1340412k swap on /dev/vda5. Priority:-1 extents:1 across:1340412k [ 1.081351] udev[313]: starting version 163 [ 1.090049] EXT4-fs (vda1): re-mounted. Opts: errors=remount-ro [ 1.330651] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0xb100, revision 0 [ 1.363116] type=1400 audit(1298144570.661:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=511 comm="apparmor_parser" [ 1.363451] type=1400 audit(1298144570.661:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=511 comm="apparmor_parser" [ 1.363630] type=1400 audit(1298144570.661:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=511 comm="apparmor_parser" [ 1.370818] lp: driver loaded but no devices found [ 1.411803] type=1400 audit(1298144570.711:5): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=542 comm="apparmor_parser" [ 1.443977] IR NEC protocol handler initialized [ 1.455486] saa7146: register extension 'budget_ci dvb'. [ 1.475556] usbcore: registered new interface driver hiddev [ 1.494165] IR RC5(x) protocol handler initialized [ 1.497985] input: QEMU 0.12.5 QEMU USB Tablet as /devices/pci0000:00/0000:00:01.2/usb1/1-1/1-1:1.0/input/input2 [ 1.498098] generic-usb 0003:0627:0001.0001: input,hidraw0: USB HID v0.01 Pointer [QEMU 0.12.5 QEMU USB Tablet] on usb-0000:00:01.2-1/input0 [ 1.498113] usbcore: registered new interface driver usbhid [ 1.498115] usbhid: USB HID core driver [ 1.530518] IR RC6 protocol handler initialized [ 1.556661] IR JVC protocol handler initialized [ 1.558141] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 [ 1.558152] budget_ci dvb 0000:00:06.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, high) -> IRQ 11 [ 1.558191] budget_ci dvb 0000:00:06.0: setting latency timer to 64 [ 1.558250] saa7146: found saa7146 @ mem ffffc9000183a000 (revision 1, irq 11) (0x13c2,0x1019). [ 1.558254] saa7146 (0): dma buffer size 192512 [ 1.558256] DVB: registering new adapter (TT-Budget S2-3200 PCI) [ 1.597796] IR Sony protocol handler initialized [ 1.612193] lirc_dev: IR Remote Control driver registered, major 250 [ 1.613142] IR LIRC bridge handler initialized [ 1.760097] Couldn't read from EEPROM: not there? [ 1.793653] type=1400 audit(1298144571.091:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=701 comm="apparmor_parser" [ 1.793989] type=1400 audit(1298144571.091:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/ m-dhcp-client.action" pid=701 comm="apparmor_parser" [ 1.794172] type=1400 audit(1298144571.091:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=701 comm="apparmor_parser" [ 1.813762] type=1400 audit(1298144571.111:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/mysqld" pid=706 comm="apparmor_parser" [ 1.820146] Registered IR keymap rc-tt-1500 [ 1.820311] input: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:06.0/rc/rc0/input3 [ 1.820399] rc0: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:06.0/rc/rc0 [ 2.196440] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input4 [ 2.199724] type=1400 audit(1298144571.501:10): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/ntpd" pid=709 comm="apparmor_parser" [ 2.461868] JBD: barrier-based sync failed on vda1-8 - disabling barriers [ 2.622108] EXT4-fs (vda1): re-mounted. Opts: errors=remount-ro,commit=0 [ 2.647887] JBD: barrier-based sync failed on vda1-8 - disabling barriers [ 2.860139] _stb0899_read_s2reg ERR(1), Device=[0xf3fc], Base address=[0x00000400], Offset=[0xf334], Status=-1 [ 2.960154] _stb0899_read_s2reg ERR(1), Device=[0xf3fc], Base address=[0x00000400], Offset=[0xf33c], Status=-1 [ 3.060140] _stb0899_read_s2reg ERR(1), Device=[0xfafc], Base address=[0x00000800], Offset=[0xfa2c], Status=-1 [ 3.160140] _stb0899_read_s2reg ERR(1), Device=[0xfafc], Base address=[0x00000800], Offset=[0xfa34], Status=-1 [ 3.160948] stb0899_attach: Attaching STB0899 [ 3.164956] stb6100_attach: Attaching STB6100 [ 3.260217] frontend_init: No LNBP21 found! [ 3.260237] budget-ci: A frontend driver was not found for device [1131:7146] subsystem [13c2:1019] [ 3.260451] budget_ci dvb 0000:00:07.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, high) -> IRQ 10 [ 3.260579] budget_ci dvb 0000:00:07.0: setting latency timer to 64 [ 3.260817] saa7146: found saa7146 @ mem ffffc90001830000 (revision 1, irq 10) (0x13c2,0x1019). [ 3.260828] saa7146 (1): dma buffer size 192512 [ 3.260841] DVB: registering new adapter (TT-Budget S2-3200 PCI) [ 3.470057] Couldn't read from EEPROM: not there? [ 3.470535] Registered IR keymap rc-tt-1500 [ 3.470592] input: Budget-CI dvb ir receiver saa7146 (1) as /devices/pci0000:00/0000:00:07.0/rc/rc1/input5 [ 3.470631] rc1: Budget-CI dvb ir receiver saa7146 (1) as /devices/pci0000:00/0000:00:07.0/rc/rc1 [ 4.500077] _stb0899_read_s2reg ERR(1), Device=[0xf3fc], Base address=[0x00000400], Offset=[0xf334], Status=-1 [ 4.600084] _stb0899_read_s2reg ERR(1), Device=[0xf3fc], Base address=[0x00000400], Offset=[0xf33c], Status=-1 [ 4.700102] _stb0899_read_s2reg ERR(1), Device=[0xfafc], Base address=[0x00000800], Offset=[0xfa2c], Status=-1 [ 4.800088] _stb0899_read_s2reg ERR(1), Device=[0xfafc], Base address=[0x00000800], Offset=[0xfa34], Status=-1 [ 4.800894] stb0899_attach: Attaching STB0899 [ 4.801048] stb6100_attach: Attaching STB6100 [ 4.900190] frontend_init: No LNBP21 found! [ 4.900204] budget-ci: A frontend driver was not found for device [1131:7146] subsystem [13c2:1019] [ 4.900368] Intel ICH 0000:00:04.0: PCI INT A -> Link[LNKD] -> GSI 11 (level,high) -> IRQ 11 [ 4.900448] Intel ICH 0000:00:04.0: setting latency timer to 64 [ 5.233183] saa7146 (0): unexpected i2c irq: isr e7fffbb7 psr ffffffff ssr ffffffff [ 5.233189] saa7146: interrupt_hw(): warning: interrupt enabled, but not handled properly.(0xe7fcfbb7) [ 5.233194] saa7146: interrupt_hw(): disabling interrupt source(s)! [ 5.607824] saa7146 (0): unexpected i2c irq: isr e7fffbb7 psr ffffffff ssr ffffffff [ 5.607827] saa7146: interrupt_hw(): warning: interrupt enabled, but not handled properly.(0xe7fcfbb7) [ 5.607830] saa7146: interrupt_hw(): disabling interrupt source(s)! [ 5.982592] saa7146 (0): unexpected i2c irq: isr e7fffbb7 psr ffffffff ssr ffffffff [ 5.982595] saa7146: interrupt_hw(): warning: interrupt enabled, but not handled properly.(0xe7fcfbb7) [ 5.982597] saa7146: interrupt_hw(): disabling interrupt source(s)! [ 6.355018] saa7146 (0): unexpected i2c irq: isr e7fffbb7 psr ffffffff ssr ffffffff [ 6.355020] saa7146: interrupt_hw(): warning: interrupt enabled, but not handled properly.(0xe7fcfbb7) [ 6.355022] saa7146: interrupt_hw(): disabling interrupt source(s)! >>> filtered for the frontend Problem: virtual-machine:/dev/dvb/adapter0$ dmesg | grep frontend [ 3.260217] frontend_init: No LNBP21 found! [ 3.260237] budget-ci: A frontend driver was not found for device [1131:7146] subsystem [13c2:1019] [ 4.900190] frontend_init: No LNBP21 found! [ 4.900204] budget-ci: A frontend driver was not found for device [1131:7146] subsystem [13c2:1019] ------------------------------------------------------------------------------- with only one card i get it working and i am able to scan the satellites: [ 29.024740] DVB: registering adapter 0 frontend 0 (STB0899 Multistandard)... dmesg with only one card - WORKING: virtual-machine:~$ dmesg [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.35-25-generic (buildd@crested) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #44-Ubuntu SMP Fri Jan 21 17:40:44 UTC 2011 (Ubuntu 2.6.35-25.44-generic 2.6.35.10) [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-25-generic root=UUID=58eb9e81-3bc6-4266-ad52-8030a004f4ba ro quiet splash [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable) [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfffb000 (usable) [ 0.000000] BIOS-e820: 00000000dfffb000 - 00000000e0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fffbc000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000132300000 (usable) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.4 present. [ 0.000000] e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] No AGP bridge found [ 0.000000] last_pfn = 0x132300 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: write-back [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 00E0000000 mask FFE0000000 uncachable [ 0.000000] 1 disabled [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] PAT not supported by CPU. [ 0.000000] last_pfn = 0xdfffb max_arch_pfn = 0x400000000 [ 0.000000] e820 update range: 0000000000001000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] Scanning 1 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 000000000009f000 (usable) [ 0.000000] modified: 000000000009f000 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 00000000dfffb000 (usable) [ 0.000000] modified: 00000000dfffb000 - 00000000e0000000 (reserved) [ 0.000000] modified: 00000000fffbc000 - 0000000100000000 (reserved) [ 0.000000] modified: 0000000100000000 - 0000000132300000 (usable) [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] found SMP MP-table at [ffff8800000f8880] f8880 [ 0.000000] init_memory_mapping: 0000000000000000-00000000dfffb000 [ 0.000000] 0000000000 - 00dfe00000 page 2M [ 0.000000] 00dfe00000 - 00dfffb000 page 4k [ 0.000000] kernel direct mapping tables up to dfffb000 @ 16000-1c000 [ 0.000000] init_memory_mapping: 0000000100000000-0000000132300000 [ 0.000000] 0100000000 - 0132200000 page 2M [ 0.000000] 0132200000 - 0132300000 page 4k [ 0.000000] kernel direct mapping tables up to 132300000 @ 1a000-21000 [ 0.000000] RAMDISK: 37572000 - 37ff0000 [ 0.000000] ACPI: RSDP 00000000000f8830 00014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 00000000dfffdd90 00034 (v01 BOCHS BXPCRSDT 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 00000000dffffe70 00074 (v01 BOCHS BXPCFACP 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 00000000dfffdf30 01EC4 (v01 BXPC BXDSDT 00000001 INTL 20100528) [ 0.000000] ACPI: FACS 00000000dffffe00 00040 [ 0.000000] ACPI: SSDT 00000000dfffdef0 00037 (v01 BOCHS BXPCSSDT 00000001 BXPC 00000001) [ 0.000000] ACPI: APIC 00000000dfffde10 00072 (v01 BOCHS BXPCAPIC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 00000000dfffddd0 00038 (v01 BOCHS BXPCHPET 00000001 BXPC 00000001) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-0000000132300000 [ 0.000000] Initmem setup node 0 0000000000000000-0000000132300000 [ 0.000000] NODE_DATA [0000000100000000 - 0000000100004fff] [ 0.000000] kvm-clock: Using msrs 12 and 11 [ 0.000000] kvm-clock: cpu 0, msr 0:1aeb901, boot clock [ 0.000000] [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880100200000-ffff8801041fffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00132300 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x000dfffb [ 0.000000] 0: 0x00100000 -> 0x00132300 [ 0.000000] On node 0 totalpages: 1122954 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3927 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 899123 pages, LIFO batch:31 [ 0.000000] Normal zone: 2811 pages used for memmap [ 0.000000] Normal zone: 202757 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0xb008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ5 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ10 used by override. [ 0.000000] ACPI: IRQ11 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] early_res array is doubled to 64 at [1c000 - 1c7ff] [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000dfffb000 - 00000000e0000000 [ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000fffbc000 [ 0.000000] PM: Registered nosave memory: 00000000fffbc000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:1ffbc000) [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880001e00000 s91520 r8192 d23168 u2097152 [ 0.000000] pcpu-alloc: s91520 r8192 d23168 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] kvm-clock: cpu 0, msr 0:1e15901, primary cpu clock [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1105807 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.35-25-generic root=UUID=58eb9e81-3bc6-4266-ad52-8030a004f4ba ro quiet splash [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] Subtract (49 early reservations) [ 0.000000] #1 [0001000000 - 0001d17114] TEXT DATA BSS [ 0.000000] #2 [0037572000 - 0037ff0000] RAMDISK [ 0.000000] #3 [0001d18000 - 0001d18071] BRK [ 0.000000] #4 [000009f000 - 00000f8880] BIOS reserved [ 0.000000] #5 [00000f8880 - 00000f8890] MP-table mpf [ 0.000000] #6 [00000f8990 - 0000100000] BIOS reserved [ 0.000000] #7 [00000f8890 - 00000f8990] MP-table mpc [ 0.000000] #8 [0000010000 - 0000012000] TRAMPOLINE [ 0.000000] #9 [0000012000 - 0000016000] ACPI WAKEUP [ 0.000000] #10 [0000016000 - 000001a000] PGTABLE [ 0.000000] #11 [000001a000 - 000001c000] PGTABLE [ 0.000000] #12 [0100000000 - 0100005000] NODE_DATA [ 0.000000] #13 [0001d18080 - 0001d19080] BOOTMEM [ 0.000000] #14 [0001d17140 - 0001d17488] BOOTMEM [ 0.000000] #15 [0100005000 - 0100006000] BOOTMEM [ 0.000000] #16 [0100006000 - 0100007000] BOOTMEM [ 0.000000] #17 [0100200000 - 0104200000] MEMMAP 0 [ 0.000000] #18 [0001d174c0 - 0001d17640] BOOTMEM [ 0.000000] #19 [0001d19080 - 0001d31080] BOOTMEM [ 0.000000] #20 [0001d31080 - 0001d37080] BOOTMEM [ 0.000000] #21 [0001d38000 - 0001d39000] BOOTMEM [ 0.000000] #22 [0001d17640 - 0001d17681] BOOTMEM [ 0.000000] #23 [0001d176c0 - 0001d17703] BOOTMEM [ 0.000000] #24 [0001d17740 - 0001d17900] BOOTMEM [ 0.000000] #25 [0001d17900 - 0001d17968] BOOTMEM [ 0.000000] #26 [0001d17980 - 0001d179e8] BOOTMEM [ 0.000000] #27 [0001d17a00 - 0001d17a68] BOOTMEM [ 0.000000] #28 [0001d17a80 - 0001d17ae8] BOOTMEM [ 0.000000] #29 [0001d17b00 - 0001d17b68] BOOTMEM [ 0.000000] #30 [0001d17b80 - 0001d17be8] BOOTMEM [ 0.000000] #31 [0001d17c00 - 0001d17c68] BOOTMEM [ 0.000000] #32 [0001d17c80 - 0001d17ca0] BOOTMEM [ 0.000000] #33 [0001d17cc0 - 0001d17ce0] BOOTMEM [ 0.000000] #34 [0001d17d00 - 0001d17d6a] BOOTMEM [ 0.000000] #35 [0001d17d80 - 0001d17dea] BOOTMEM [ 0.000000] #36 [0001e00000 - 0001e1e000] BOOTMEM [ 0.000000] #37 [0001d17e00 - 0001d17e08] BOOTMEM [ 0.000000] #38 [0001d17e40 - 0001d17e48] BOOTMEM [ 0.000000] #39 [0001d17e80 - 0001d17e84] BOOTMEM [ 0.000000] #40 [0001d17ec0 - 0001d17ec8] BOOTMEM [ 0.000000] #41 [0001d37080 - 0001d371d0] BOOTMEM [ 0.000000] #42 [0001d17f00 - 0001d17f80] BOOTMEM [ 0.000000] #43 [0001d17f80 - 0001d18000] BOOTMEM [ 0.000000] #44 [0001d39000 - 0001d41000] BOOTMEM [ 0.000000] #45 [0001e1e000 - 0005e1e000] BOOTMEM [ 0.000000] #46 [0001d41000 - 0001d61000] BOOTMEM [ 0.000000] #47 [0001d61000 - 0001da1000] BOOTMEM [ 0.000000] #48 [000001c800 - 0000024800] BOOTMEM [ 0.000000] Memory: 4335812k/5016576k available (5714k kernel code, 524760k absent, 156004k reserved, 5377k data, 908k init) [ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] Verbose stalled-CPUs detection is disabled. [ 0.000000] NR_IRQS:4352 nr_irqs:256 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 45875200 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] hpet clockevent registered [ 0.000000] Detected 3324.678 MHz processor. [ 0.010000] Calibrating delay loop (skipped) preset value.. 6649.35 BogoMIPS (lpj=33246780) [ 0.010000] pid_max: default: 32768 minimum: 301 [ 0.010000] Security Framework initialized [ 0.010000] AppArmor: AppArmor initialized [ 0.010000] Yama: becoming mindful. [ 0.010000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.010000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.010000] Mount-cache hash table entries: 256 [ 0.010000] Initializing cgroup subsys ns [ 0.010000] Initializing cgroup subsys cpuacct [ 0.010000] Initializing cgroup subsys memory [ 0.010000] Initializing cgroup subsys devices [ 0.010000] Initializing cgroup subsys freezer [ 0.010000] Initializing cgroup subsys net_cls [ 0.010013] mce: CPU supports 10 MCE banks [ 0.010056] Performance Events: unsupported p6 CPU model 2 no PMU driver, software events only. [ 0.010245] SMP alternatives: switching to UP code [ 0.032015] Freeing SMP alternatives: 24k freed [ 0.032041] ACPI: Core revision 20100428 [ 0.033733] ftrace: converting mcount calls to 0f 1f 44 00 00 [ 0.033739] ftrace: allocating 22681 entries in 89 pages [ 0.040085] Setting APIC routing to flat [ 0.041000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.041003] CPU0: Intel QEMU Virtual CPU version 0.12.5 stepping 03 [ 0.050000] Brought up 1 CPUs [ 0.050000] Total of 1 processors activated (6649.35 BogoMIPS). [ 0.050000] devtmpfs: initialized [ 0.050000] regulator: core version 0.5 [ 0.050000] Time: 21:12:25 Date: 02/19/11 [ 0.050000] NET: Registered protocol family 16 [ 0.050000] ACPI: bus type pci registered [ 0.050000] PCI: Using configuration type 1 for base access [ 0.050000] bio: create slab <bio-0> at 0 [ 0.050000] ACPI: EC: Look up EC in DSDT [ 0.050000] ACPI: Interpreter enabled [ 0.050000] ACPI: (supports S0 S3 S4 S5) [ 0.050000] ACPI: Using IOAPIC for interrupt routing [ 0.050000] ACPI: No dock devices found. [ 0.050000] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug [ 0.050000] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.050000] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored) [ 0.050000] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored) [ 0.050000] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored) [ 0.050000] pci_root PNP0A03:00: host bridge window [mem 0xe0000000-0xfebfffff] (ignored) [ 0.050000] pci 0000:00:01.1: reg 20: [io 0xc000-0xc00f] [ 0.050000] pci 0000:00:01.2: reg 20: [io 0xc020-0xc03f] [ 0.050000] pci 0000:00:01.3: quirk: [io 0xb000-0xb03f] claimed by PIIX4 ACPI [ 0.050000] pci 0000:00:01.3: quirk: [io 0xb100-0xb10f] claimed by PIIX4 SMB [ 0.050000] pci 0000:00:02.0: reg 10: [mem 0xf0000000-0xf1ffffff pref] [ 0.050680] pci 0000:00:02.0: reg 14: [mem 0xf2000000-0xf2000fff] [ 0.053703] pci 0000:00:02.0: reg 30: [mem 0xf2010000-0xf201ffff pref] [ 0.053893] pci 0000:00:03.0: reg 10: [io 0xc040-0xc05f] [ 0.053919] pci 0000:00:03.0: reg 14: [mem 0xf2020000-0xf2020fff] [ 0.053991] pci 0000:00:03.0: reg 30: [mem 0xf2028000-0xf202ffff pref] [ 0.054150] pci 0000:00:04.0: reg 10: [io 0xc400-0xc7ff] [ 0.054171] pci 0000:00:04.0: reg 14: [io 0xc800-0xc8ff] [ 0.054350] pci 0000:00:05.0: reg 10: [io 0xc900-0xc93f] [ 0.054375] pci 0000:00:05.0: reg 14: [mem 0xf2030000-0xf2030fff] [ 0.054864] pci 0000:00:06.0: reg 10: [mem 0xf2031000-0xf2031fff] [ 0.055153] pci 0000:00:07.0: reg 10: [io 0xc940-0xc95f] [ 0.055405] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.058018] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11) [ 0.058100] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11) [ 0.060129] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11) [ 0.060215] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11) [ 0.060299] ACPI: PCI Interrupt Link [LNKS] (IRQs 9) *0 [ 0.060363] HEST: Table is not found! [ 0.060568] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none [ 0.060572] vgaarb: loaded [ 0.060736] SCSI subsystem initialized [ 0.060859] libata version 3.00 loaded. [ 0.060914] usbcore: registered new interface driver usbfs [ 0.060925] usbcore: registered new interface driver hub [ 0.060958] usbcore: registered new device driver usb [ 0.061092] ACPI: WMI: Mapper loaded [ 0.061097] PCI: Using ACPI for IRQ routing [ 0.061101] PCI: pci_cache_line_size set to 64 bytes [ 0.061255] reserve RAM buffer: 000000000009f000 - 000000000009ffff [ 0.061259] reserve RAM buffer: 00000000dfffb000 - 00000000dfffffff [ 0.061260] reserve RAM buffer: 0000000132300000 - 0000000133ffffff [ 0.061379] NetLabel: Initializing [ 0.061382] NetLabel: domain hash size = 128 [ 0.061383] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.061395] NetLabel: unlabeled traffic allowed by default [ 0.061437] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.061455] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.061458] hpet0: 3 comparators, 64-bit 100.000000 MHz counter [ 0.080036] Switching to clocksource kvm-clock [ 0.088177] AppArmor: AppArmor Filesystem Enabled [ 0.088203] pnp: PnP ACPI init [ 0.088224] ACPI: bus type pnp registered [ 0.088851] pnp: PnP ACPI: found 6 devices [ 0.088853] ACPI: ACPI bus type pnp unregistered [ 0.094481] pci_bus 0000:00: resource 0 [io 0x0000-0xffff] [ 0.094484] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff] [ 0.094515] NET: Registered protocol family 2 [ 0.094690] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.095933] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.099355] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.099799] TCP: Hash tables configured (established 524288 bind 65536) [ 0.099801] TCP reno registered [ 0.099812] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.099898] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.100072] NET: Registered protocol family 1 [ 0.100089] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 0.100113] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 0.100130] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 0.100199] pci 0000:00:02.0: Boot video device [ 0.100240] PCI: CLS 0 bytes, default 64 [ 0.100257] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.100260] Placing 64MB software IO TLB between ffff880001e1e000 - ffff880005e1e000 [ 0.100262] software IO TLB at phys 0x1e1e000 - 0x5e1e000 [ 0.100459] Scanning for low memory corruption every 60 seconds [ 0.100609] audit: initializing netlink socket (disabled) [ 0.100626] type=2000 audit(1298149947.100:1): initialized [ 0.110370] Trying to unpack rootfs image as initramfs... [ 0.130254] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.131175] VFS: Disk quotas dquot_6.5.2 [ 0.131216] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.140277] fuse init (API version 7.14) [ 0.140368] msgmni has been set to 8468 [ 0.142503] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.142511] io scheduler noop registered [ 0.142512] io scheduler deadline registered [ 0.142536] io scheduler cfq registered (default) [ 0.142604] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.142618] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.142736] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.142744] ACPI: Power Button [PWRF] [ 0.142992] ACPI: acpi_idle registered with cpuidle [ 0.143584] ERST: Table is not found! [ 0.143683] Linux agpgart interface v0.103 [ 0.143701] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.143852] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.144712] brd: module loaded [ 0.145035] loop: module loaded [ 0.145156] ata_piix 0000:00:01.1: version 2.13 [ 0.145231] ata_piix 0000:00:01.1: setting latency timer to 64 [ 0.150073] scsi0 : ata_piix [ 0.150167] scsi1 : ata_piix [ 0.150189] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc000 irq 14 [ 0.150190] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc008 irq 15 [ 0.150371] Fixed MDIO Bus: probed [ 0.150393] PPP generic driver version 2.4.2 [ 0.150435] tun: Universal TUN/TAP device driver, 1.6 [ 0.150436] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> [ 0.150511] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.150523] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.150529] uhci_hcd: USB Universal Host Controller Interface driver [ 0.150716] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 [ 0.150735] uhci_hcd 0000:00:01.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, high) -> IRQ 11 [ 0.150753] uhci_hcd 0000:00:01.2: setting latency timer to 64 [ 0.150759] uhci_hcd 0000:00:01.2: UHCI Host Controller [ 0.150795] uhci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1 [ 0.150874] uhci_hcd 0000:00:01.2: irq 11, io base 0x0000c020 [ 0.151001] hub 1-0:1.0: USB hub found [ 0.151006] hub 1-0:1.0: 2 ports detected [ 0.151088] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 0.151575] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.151581] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.151687] mice: PS/2 mouse device common for all mice [ 0.151891] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 0.152116] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0 [ 0.152192] rtc0: alarms up to one day, 114 bytes nvram, hpet irqs [ 0.152290] device-mapper: uevent: version 1.0.3 [ 0.160345] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@xxxxxxxxxx [ 0.160729] device-mapper: multipath: version 1.1.1 loaded [ 0.160735] device-mapper: multipath round-robin: version 1.0.0 loaded [ 0.170094] cpuidle: using governor ladder [ 0.170096] cpuidle: using governor menu [ 0.170283] TCP cubic registered [ 0.170375] NET: Registered protocol family 10 [ 0.170640] lo: Disabled Privacy Extensions [ 0.170759] NET: Registered protocol family 17 [ 0.170898] PM: Resume from disk failed. [ 0.170917] registered taskstats version 1 [ 0.171078] Magic number: 15:797:247 [ 0.171168] rtc_cmos 00:01: setting system clock to 2011-02-19 21:12:26 UTC (1298149946) [ 0.171171] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.171172] EDD information not available. [ 0.296603] Freeing initrd memory: 10744k freed [ 0.320540] ata2.01: NODEV after polling detection [ 0.320769] ata2.00: ATAPI: QEMU DVD-ROM, 0.12.5, max UDMA/100 [ 0.321150] ata2.00: configured for MWDMA2 [ 0.321567] scsi 1:0:0:0: CD-ROM QEMU QEMU DVD-ROM 0.12 PQ: 0 ANSI: 5 [ 0.322756] sr0: scsi3-mmc drive: 4x/4x xa/form2 tray [ 0.322761] Uniform CD-ROM driver Revision: 3.20 [ 0.322854] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 0.322903] sr 1:0:0:0: Attached scsi generic sg0 type 5 [ 0.322946] Freeing unused kernel memory: 908k freed [ 0.323233] Write protecting the kernel read-only data: 10240k [ 0.323353] Freeing unused kernel memory: 412k freed [ 0.323570] Freeing unused kernel memory: 1644k freed [ 0.340251] udev[66]: starting version 163 [ 0.459148] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 [ 0.459172] virtio-pci 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, high) -> IRQ 10 [ 0.459194] virtio-pci 0000:00:03.0: setting latency timer to 64 [ 0.465102] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 [ 0.465107] virtio-pci 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, high) -> IRQ 10 [ 0.465130] virtio-pci 0000:00:05.0: setting latency timer to 64 [ 0.465408] virtio-pci 0000:00:07.0: PCI INT A -> Link[LNKC] -> GSI 10 (level, high) -> IRQ 10 [ 0.465424] virtio-pci 0000:00:07.0: setting latency timer to 64 [ 0.470080] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 0.475220] alloc irq_desc for 40 on node -1 [ 0.475223] alloc kstat_irqs on node -1 [ 0.475244] virtio-pci 0000:00:05.0: irq 40 for MSI/MSI-X [ 0.475245] alloc irq_desc for 41 on node -1 [ 0.475246] alloc kstat_irqs on node -1 [ 0.475259] virtio-pci 0000:00:05.0: irq 41 for MSI/MSI-X [ 0.505072] FDC 0 is a S82078B [ 0.505658] vda: vda1 vda2 < vda5 > [ 0.506201] alloc irq_desc for 42 on node -1 [ 0.506203] alloc kstat_irqs on node -1 [ 0.506221] virtio-pci 0000:00:03.0: irq 42 for MSI/MSI-X [ 0.506223] alloc irq_desc for 43 on node -1 [ 0.506224] alloc kstat_irqs on node -1 [ 0.506235] virtio-pci 0000:00:03.0: irq 43 for MSI/MSI-X [ 0.506237] alloc irq_desc for 44 on node -1 [ 0.506238] alloc kstat_irqs on node -1 [ 0.506249] virtio-pci 0000:00:03.0: irq 44 for MSI/MSI-X [ 0.841106] EXT4-fs (vda1): INFO: recovery required on readonly filesystem [ 0.841111] EXT4-fs (vda1): write access will be enabled during recovery [ 0.892224] usbcore: registered new interface driver hiddev [ 0.913548] input: QEMU 0.12.5 QEMU USB Tablet as /devices/pci0000:00/0000:00:01.2/usb1/1-1/1-1:1.0/input/input2 [ 0.913694] generic-usb 0003:0627:0001.0001: input,hidraw0: USB HID v0.01 Pointer [QEMU 0.12.5 QEMU USB Tablet] on usb-0000:00:01.2-1/input0 [ 0.913846] usbcore: registered new interface driver usbhid [ 0.913848] usbhid: USB HID core driver [ 11.288098] EXT4-fs (vda1): orphan cleanup on readonly fs [ 11.288130] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 526759 [ 11.288428] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 525178 [ 11.288455] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524633 [ 11.288469] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524632 [ 11.288480] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524631 [ 11.288492] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524630 [ 11.288503] EXT4-fs (vda1): ext4_orphan_cleanup: deleting unreferenced inode 524629 [ 11.288513] EXT4-fs (vda1): 7 orphan inodes deleted [ 11.288517] EXT4-fs (vda1): recovery complete [ 11.319113] JBD: barrier-based sync failed on vda1-8 - disabling barriers [ 11.574501] EXT4-fs (vda1): mounted filesystem with ordered data mode. Opts: (null) [ 28.064829] udev[294]: starting version 163 [ 28.189019] Adding 1340412k swap on /dev/vda5. Priority:-1 extents:1 across:1340412k [ 28.211614] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0xb100, revision 0 [ 28.285895] lp: driver loaded but no devices found [ 28.352237] type=1400 audit(1298149974.674:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=481 comm="apparmor_parser" [ 28.352549] type=1400 audit(1298149974.674:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=481 comm="apparmor_parser" [ 28.352720] type=1400 audit(1298149974.674:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=481 comm="apparmor_parser" [ 28.379665] type=1400 audit(1298149974.694:5): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=529 comm="apparmor_parser" [ 28.402020] IR NEC protocol handler initialized [ 28.427840] EXT4-fs (vda1): re-mounted. Opts: errors=remount-ro [ 28.455051] saa7146: register extension 'budget_ci dvb'. [ 28.500317] IR RC5(x) protocol handler initialized [ 28.530283] IR RC6 protocol handler initialized [ 28.546606] IR JVC protocol handler initialized [ 28.553373] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 [ 28.553387] budget_ci dvb 0000:00:06.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, high) -> IRQ 11 [ 28.553489] saa7146: found saa7146 @ mem ffffc900017ba000 (revision 1, irq 11) (0x13c2,0x1019). [ 28.553495] saa7146 (0): dma buffer size 192512 [ 28.553499] DVB: registering new adapter (TT-Budget S2-3200 PCI) [ 28.561480] IR Sony protocol handler initialized [ 28.598268] lirc_dev: IR Remote Control driver registered, major 250 [ 28.599474] IR LIRC bridge handler initialized [ 28.645237] adapter has MAC addr = 00:d0:5c:68:22:e7 [ 28.694006] Registered IR keymap rc-tt-1500 [ 28.694281] input: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:06.0/rc/rc0/input3 [ 28.694456] rc0: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:06.0/rc/rc0 [ 28.834269] type=1400 audit(1298149975.154:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=693 comm="apparmor_parser" [ 28.834689] type=1400 audit(1298149975.154:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 28.834936] type=1400 audit(1298149975.154:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 28.874125] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input4 [ 28.878398] type=1400 audit(1298149975.194:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/mysqld" pid=698 comm="apparmor_parser" [ 28.886916] type=1400 audit(1298149975.204:10): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/ntpd" pid=702 comm="apparmor_parser" [ 28.891401] type=1400 audit(1298149975.214:11): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=705 comm="apparmor_parser" [ 29.020971] stb0899_attach: Attaching STB0899 [ 29.022779] stb6100_attach: Attaching STB6100 [ 29.024724] LNBx2x attached on addr=8 [ 29.024740] DVB: registering adapter 0 frontend 0 (STB0899 Multistandard)... [ 29.025403] Intel ICH 0000:00:04.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, high) -> IRQ 11 [ 29.025466] Intel ICH 0000:00:04.0: setting latency timer to 64 [ 29.360264] intel8x0_measure_ac97_clock: measured 56773 usecs (4624 samples) [ 29.360266] intel8x0: measured clock 81447 rejected [ 29.730119] intel8x0_measure_ac97_clock: measured 59967 usecs (4830 samples) [ 29.730121] intel8x0: measured clock 80544 rejected [ 30.100173] intel8x0_measure_ac97_clock: measured 59837 usecs (4805 samples) [ 30.100179] intel8x0: measured clock 80301 rejected [ 30.100215] intel8x0: clocking to 48000 [ 31.392147] JBD: barrier-based sync failed on vda1-8 - disabling barriers [ 32.079085] EXT4-fs (vda1): re-mounted. Opts: errors=remount-ro,commit=0 [ 32.173516] JBD: barrier-based sync failed on vda1-8 - disabling barriers [ 39.480086] eth0: no IPv6 routers present -- To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
