On Thu, Nov 18, 2010 at 01:52:30PM +0200, Michael S. Tsirkin wrote: > On Thu, Nov 18, 2010 at 01:45:04PM +0200, Gleb Natapov wrote: > > On Thu, Nov 18, 2010 at 01:38:31PM +0200, Michael S. Tsirkin wrote: > > > On Thu, Nov 18, 2010 at 12:18:27PM +0200, Gleb Natapov wrote: > > > > On Wed, Nov 17, 2010 at 09:54:27PM +0000, Blue Swirl wrote: > > > > > 2010/11/16 Gleb Natapov <gleb@xxxxxxxxxx>: > > > > > > On Tue, Nov 16, 2010 at 06:30:19PM +0000, Blue Swirl wrote: > > > > > >> >> Perhaps the FW path should use device class names if no name is specified. > > > > > >> > What do you mean by "device class name". We can do something like this: > > > > > >> > if (dev->child_bus.lh_first) > > > > > >> > return dev->child_bus.lh_first->info->name; > > > > > >> > > > > > > >> > i.e if there is child bus use its bus name as fw name. This will make > > > > > >> > all pci devices to have "pci" as fw name automatically. The problem is > > > > > >> > that theoretically same device can provide different buses. > > > > > >> > > > > > >> I meant PCI class name, like "display" for display controllers, > > > > > >> "network" for NICs etc. > > > > > >> > > > > > > That is what my pci bus related patch is doing already. > > > > > > > > > > > >> >> I'll try Sparc32 to see how this fits there. > > > > > >> > > > > > >> Except bootindex is not implemented for SCSI. > > > > > > Will look into adding it. > > > > > > > > > > Thanks. The bootindex on Sparc32 looks like this: > > > > > bootindex /esp@0000000078800000/disk@1,0 > > > > > /ethernet@ffffffffffffffff/ethernet-phy@0 > > > > > > > > > For arches other then x86 there is a lot of work left to be done :) > > > > For starter exotic sparc buses should get their own get_fw_dev_path() > > > > implementation. > > > > > > > > > I don't think I got Lance setup right. > > > > > > > > > > OF paths for the devices would be: > > > > > /iommu@0,10000000/sbus@0,10001000/espdma@5,8400000/esp@5,8800000/sd@1,0 > > > > > /iommu@0,10000000/sbus@0,10001000/ledma@5,8400010/le@5,8c00000 > > > > If qdev hierarchy does not correspond to real HW there is no much we can > > > > do expect for fixing qdev. > > > > > > That's bad. This raises a concern: if these paths expose qdev > > > internals, any attempt to fix this will break migration. > > > > > The path expose internal HW hierarchy. It is designed to do so. Qdev > > designed to do the same: describe HW hierarchy. If qdev fails to do so it > > is broken. > > Yes. But since you use qdev to build up the path, a broken > qdev will give you a broken path. > Qdev bug. Fix it like any other bug. The nice is that when you compare device path produced by qdev and real HW you can see when qdev is wrong. > > I do not see connection to migration at all since the path is > > not used in migration code. > > The connection is that if we pass the list with path 1 which you define > as broken to BIOS, then migrate to a machine with an updated qemu > which has a correct path, BIOS won't be able to complete the boot. You solve it like you solve all such issue with -M machine type. But the problem exists only if migration happens in a short window between start of the boot process and BIOS reading boot order string. After reboot new qemu should have new BIOS. > Right? Same in reverse direction. Reverse direction is not and never was supported. > As solution could be a fuzzy matching > of paths that wiull let us recover. > Firmware can try its best of course, but nothing is guarantied. > > > > > > > > > > The logic for ESP is that ESP (registers at 0x78800000, slot offset > > > > > 0x880000) is handled by the DMA controller (registers at 0x78400000, > > > > > slot offset 0x840000), they are in a SBus slot #5, and SBus (registers > > > > > at 0x10001000) is in turn handled by IOMMU (registers at 0x10000000). > > > > > Lance should be handled the same way. > > > > > > > > > > This hierarchy is partly known by QEMU because DMA accesses use this > > > > > flow, but not otherwise. There is no concept of SBus slots, DMA talks > > > > > to IOMMU directly. Though in this case both ESP, Lance and their DMA > > > > > controllers are on board devices in a MACIO chip. It may be possible > > > > > to add the hierarchy information at each stage. > > > > > > > > > > It should also be possible for BIOS to determine the device just from > > > > > the physical address if we ignored OF compatibility. > > > > It would be nice to be OF compatible at least at some level. Of course OF > > > > spec is not strict enough to have two different implementations produce > > > > exactly same device path that can be compared by strcpy. Can we apply > > > > the series now? At least for x86 it provides useful paths and work can > > > > be continue for other arches by interested parties. > > > > > > > > -- > > > > Gleb. > > > > > > Something I only now realized is that we commit > > > to never changing the paths for any architecture > > > that supports migration. > > > > > No connection to migration whatsoever. > > It just seems silly to use different paths for the same thing. > > Besides the connection above, I was hoping to use these paths > for section names in migration. If we can't guarantee they are > stable, we'll have to roll our own, and if we do this, > with stability guarantees required for migration format, > maybe use it for other things like BIOS as well? > It doesn't matter what do you use for migration purposes as long as it depend on qdev hierarchy it will have problem when qdev hierarchy changes and if it doesn't you can't produce unique names reliably. -- Gleb. -- To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
