On Tue, 2024-04-09 at 18:12 -0700, Isaku Yamahata wrote: > On Mon, Apr 08, 2024 at 06:51:40PM +0000, > Sean Christopherson <seanjc@xxxxxxxxxx> wrote: > > > On Mon, Apr 08, 2024, Edgecombe, Rick P wrote: > > > On Mon, 2024-04-08 at 09:20 -0700, Sean Christopherson wrote: > > > > > Another option is that, KVM doesn't allow userspace to configure > > > > > CPUID(0x8000_0008).EAX[7:0]. Instead, it provides a gpaw field in struct > > > > > kvm_tdx_init_vm for userspace to configure directly. > > > > > > > > > > What do you prefer? > > > > > > > > Hmm, neither. I think the best approach is to build on Gerd's series to have KVM > > > > select 4-level vs. 5-level based on the enumerated guest.MAXPHYADDR, not on > > > > host.MAXPHYADDR. > > > > > > So then GPAW would be coded to basically best fit the supported guest.MAXPHYADDR within KVM. QEMU > > > could look at the supported guest.MAXPHYADDR and use matching logic to determine GPAW. > > > > Off topic, any chance I can bribe/convince you to wrap your email replies closer > > to 80 chars, not 100? Yeah, checkpath no longer complains when code exceeds 80 > > chars, but my brain is so well trained for 80 that it actually slows me down a > > bit when reading mails that are wrapped at 100 chars. > > > > > Or are you suggesting that KVM should look at the value of CPUID(0X8000_0008).eax[23:16] passed from > > > userspace? > > > > This. Note, my pseudo-patch incorrectly looked at bits 15:8, that was just me > > trying to go off memory. > > > > > I'm not following the code examples involving struct kvm_vcpu. Since TDX > > > configures these at a VM level, there isn't a vcpu. > > > > Ah, I take it GPAW is a VM-scope knob? I forget where we ended up with the ordering > > of TDX commands vs. creating vCPUs. Does KVM allow creating vCPU structures in > > advance of the TDX INIT call? If so, the least awful solution might be to use > > vCPU0's CPUID. > > The current order is, KVM vm creation (KVM_CREATE_VM), > KVM vcpu creation(KVM_CREATE_VCPU), TDX VM initialization (KVM_TDX_INIT_VM). > and TDX VCPU initialization(KVM_TDX_INIT_VCPU). > We can call KVM_SET_CPUID2 before KVM_TDX_INIT_VM. We can remove cpuid part > from struct kvm_tdx_init_vm by vcpu0 cpuid. What's the reason to call KVM_TDX_INIT_VM after KVM_CREATE_VCPU? I guess I have been away for this for too long time, but I had believed KVM_TDX_INIT_VM is called before creating any vcpu, which turns out to be wrong. I am not against to make KVM_TDX_INIT_VM must be called after creating (at least one?) vcpu if there's good reason, but it seems if the purpose is just to pass CPUID(0x8000_0008).EAX[23:16] to KVM so KVM can determine GPAW for TDX guest, then we can also make KVM_TDX_INIT_VM to pass that. KVM just need to manually handle CPUID(0x8000_0008) in KVM_TDX_INIT_VM, but that's the thing KVM needs to do anyway even if we use vcpu0's CPUID. Am I missing anything?
