On 30/08/15 14:54, Christoffer Dall wrote: > Mapped interrupts on arm/arm64 is a tricky concept and the way we deal > with them is not apparently easy to understand by reading various specs. > > Therefore, add a proper documentation file explaining the flow and > rationale of the behavior of the vgic. > > Some of this text was contributed by Marc Zyngier. > > Signed-off-by: Christoffer Dall <christoffer.dall@xxxxxxxxxx> > --- > Documentation/virtual/kvm/arm/vgic-mapped-irqs.txt | 59 ++++++++++++++++++++++ > 1 file changed, 59 insertions(+) > create mode 100644 Documentation/virtual/kvm/arm/vgic-mapped-irqs.txt > > diff --git a/Documentation/virtual/kvm/arm/vgic-mapped-irqs.txt b/Documentation/virtual/kvm/arm/vgic-mapped-irqs.txt > new file mode 100644 > index 0000000..49e1357 > --- /dev/null > +++ b/Documentation/virtual/kvm/arm/vgic-mapped-irqs.txt > @@ -0,0 +1,59 @@ > +KVM/ARM VGIC Mapped Interrupts > +============================== > + > +Setting the Physical Active State for Edge vs. Level Triggered IRQs > +------------------------------------------------------------------- > + > +Mapped non-shared interrupts injected to a guest should always mark the > +interrupt as active on the physical distributor. > + > +The reasoning for level-triggered interrupts: > +For level-triggered interrupts, we have to mark the interrupt as active > +on the physical distributor, because otherwise, as the line remains > +asserted, the guest will never execute because the host will keep taking > +interrupts. As soon as the guest deactivates the interrupt, the > +physical line is sampled by the hardware again and the host takes a new > +interrupt if the physical line is still asserted. > + > +The reasoning for edge-triggered interrupts: > +For edge-triggered interrupts, if we set the HW bit in the LR we also > +have to mark the interrupt as active on the physical distributor. If we > +don't set the physical active bit and the interrupt hits again before > +the guest has deactivated the interrupt, the interrupt goes to the host, > +which cannot set the state to ACTIVE+PENDING in the LR, because that is > +not supported when setting the HW bit in the LR. > + > +An alternative could be to not use HW bit at all, and inject > +edge-triggered interrupts from a physical assigned device as pure > +virtual interrupts, but that would potentially slow down handling of the > +interrupt in the guest, because a physical interrupt occurring in the > +middle of the guest ISR would preempt the guest for the host to handle > +the interrupt. It would be worth mentioning that this is valid for PPIs and SPIs. LPIs do not have an Active state (they are either Pending or not), so we'll have to deal with edge interrupts as you just described at some point. Other architectures do something similar, I'd expect. > + > + > +Life Cycle for Forwarded Physical Interrupts > +-------------------------------------------- > + > +By forwarded physical interrupts we mean interrupts presented to a guest > +representing a real HW event originally signaled to the host as a s/signaled/signalled/ > +physical interrupt and injecting this as a virtual interrupt with the HW > +bit set in the LR. > + > +The state of such an interrupt is managed in the following way: > + > + - LR.Pending must be set when the interrupt is first injected, because this > + is the only way the GICV interface is going to present it to the guest. > + - LR.Pending will stay set as long as the guest has not acked the interrupt. > + - LR.Pending transitions to LR.Active on read of IAR, as expected. > + - On EOI, the *physical distributor* active bit gets cleared, but the > + LR.Active is left untouched - it looks like the GIC can only clear a > + single bit (either the virtual active, or the physical one). > + - This means we cannot trust LR.Active to find out about the state of the > + interrupt, and we definitely need to look at the distributor version. > + > +Consequently, when we context switch the state of a VCPU with forwarded > +physical interrupts, we must context switch set pending *or* active bits in the > +LR for that VCPU until the guest has deactivated the physical interrupt, and > +then clear the corresponding bits in the LR. If we ever set an LR to pending or > +mapped when switching in a VCPU for a forwarded physical interrupt, we must also > +set the active state on the *physical distributor*. > I wonder if it may be worth adding a small example with the timer, because it is not immediately obvious why the interrupt would fire on and on without putting the generating device in the picture... Thanks, M. -- Jazz is not dead. It just smells funny... -- To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
