On 2014/12/29 12:15, Li, ZhenHua wrote:
> Hi Takao Indoh,
>
> Happy New Year, and thank you very much for you help. The flush is quite
Happy new year!
> a problem, as there are several places the flush function should be called,
> I think the flush should be placed in functions like __iommu_update_old_*.
> Created a small patch for this, it is attached.
>
>
>
> As I cannot reproduce your problems on my system, so could you please try
> these steps?
> 1. Apply the latest patchset, including 9/10 and 10/10, and then apply the
> attached patch_for_flush.patch. And then test the kernel.
No inter-remap fault, but there is still DMAR fault message.
>
> 2. If 1 does not fix the DMAR fault problems, then it might be caused by
> 7/10, so please *unpatch* it from the kernel (others and the attached one
> should be patched), and then test the kernel.
DMAR fault still occurs. I'll dig iommu driver code to find out the
reason.
Thanks,
Takao Indoh
>
> Regards
> Zhenhua
>
> On 12/26/2014 03:27 PM, Takao Indoh wrote:
>> On 2014/12/26 15:46, Li, ZhenHua wrote:
>>> Hi Takao Indoh,
>>>
>>> Thank you very much for your testing. I will add your update in next
>>> version.
>>> Also I think a flush for __iommu_update_old_root_entry is also necessary.
>>>
>>> Currently I have no idea about your fault, does it happen before or
>>> during its loading? Could you send me your full kernel log as an
>>> attachment?
>> Sure, see attached file.
>>
>> I removed 9/10 and 10/10 patches from my kernel to avoid panic problem I
>> reported in previous mail, and then tested kdump. So please ignore
>> intr-remap fault message in log file. Also please ignore stack trace
>> starting with the following message, it's a problem of my box.
>>
>> Flags mismatch irq 0. 00000080 (i801_smbus) vs. 00015a00 (timer)
>>
>> Thanks,
>> Takao Indoh
>>
>>> Regards and Merry Christmas.
>>> Zhenhua
>>>
>>> On 12/26/2014 01:13 PM, Takao Indoh wrote:
>>>> Hi Zhen-Hua,
>>>>
>>>> I tested your patch and found two problems.
>>>>
>>>> [1]
>>>> Kenel panic occurs during 2nd kernel boot.
>>>>
>>>> ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
>>>> Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC
>>>> CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.18.0 #25
>>>> Hardware name: FUJITSU-SV PRIMERGY BX920 S2/D3030, BIOS 080015 Rev.3D81.3030 02/10/2012
>>>> 0000000000000002 ffff880036167d08 ffffffff815b1c6a 0000000000000000
>>>> ffffffff817f7670 ffff880036167d88 ffffffff815b19f1 0000000000000008
>>>> ffff880036167d98 ffff880036167d38 ffffffff810a5d2f ffff880036167d98
>>>> Call Trace:
>>>> [<ffffffff815b1c6a>] dump_stack+0x48/0x5e
>>>> [<ffffffff815b19f1>] panic+0xbb/0x1fa
>>>> [<ffffffff810a5d2f>] ? vprintk_default+0x1f/0x30
>>>> [<ffffffff814c6a6c>] panic_if_irq_remap+0x1c/0x20
>>>> [<ffffffff81b53985>] check_timer+0x1e7/0x5ed
>>>> [<ffffffff8129bd9d>] ? radix_tree_lookup+0xd/0x10
>>>> [<ffffffff81b5413b>] setup_IO_APIC+0x261/0x292
>>>> [<ffffffff81b50302>] native_smp_prepare_cpus+0x214/0x25d
>>>> [<ffffffff81b41c65>] kernel_init_freeable+0x1dc/0x28c
>>>> [<ffffffff815aaf00>] ? rest_init+0x80/0x80
>>>> [<ffffffff815aaf0e>] kernel_init+0xe/0xf0
>>>> [<ffffffff815b5d2c>] ret_from_fork+0x7c/0xb0
>>>> [<ffffffff815aaf00>] ? rest_init+0x80/0x80
>>>> ---[ end Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC
>>>>
>>>>
>>>> This panic seems to be related to unflushed cache. I confirmed this
>>>> problem was fixed by the following patch.
>>>>
>>>> --- a/drivers/iommu/intel_irq_remapping.c
>>>> +++ b/drivers/iommu/intel_irq_remapping.c
>>>> @@ -200,8 +200,13 @@ static int modify_irte(int irq, struct irte *irte_modified)
>>>> set_64bit(&irte->high, irte_modified->high);
>>>>
>>>> #ifdef CONFIG_CRASH_DUMP
>>>> - if (is_kdump_kernel())
>>>> + if (is_kdump_kernel()) {
>>>> __iommu_update_old_irte(iommu, index);
>>>> + __iommu_flush_cache(iommu,
>>>> + iommu->ir_table->base_old_virt +
>>>> + index * sizeof(struct irte),
>>>> + sizeof(struct irte));
>>>> + }
>>>> #endif
>>>> __iommu_flush_cache(iommu, irte, sizeof(*irte));
>>>>
>>>>
>>>> [2]
>>>> Some DMAR error messages are still found in 2nd kernel boot.
>>>>
>>>> dmar: DRHD: handling fault status reg 2
>>>> dmar: DMAR:[DMA Write] Request device [01:00.0] fault addr ffded000
>>>> DMAR:[fault reason 01] Present bit in root entry is clear
>>>>
>>>> I confiremd your commit 1a2262 was already applied. Any idea?
>>>>
>>>> Thanks,
>>>> Takao Indoh
>>>>
>>>>
>>>> On 2014/12/22 18:15, Li, Zhen-Hua wrote:
>>>>> This patchset is an update of Bill Sumner's patchset, implements a fix for:
>>>>> If a kernel boots with intel_iommu=on on a system that supports intel vt-d,
>>>>> when a panic happens, the kdump kernel will boot with these faults:
>>>>>
>>>>> dmar: DRHD: handling fault status reg 102
>>>>> dmar: DMAR:[DMA Read] Request device [01:00.0] fault addr fff80000
>>>>> DMAR:[fault reason 01] Present bit in root entry is clear
>>>>>
>>>>> dmar: DRHD: handling fault status reg 2
>>>>> dmar: INTR-REMAP: Request device [[61:00.0] fault index 42
>>>>> INTR-REMAP:[fault reason 34] Present field in the IRTE entry is clear
>>>>>
>>>>> On some system, the interrupt remapping fault will also happen even if the
>>>>> intel_iommu is not set to on, because the interrupt remapping will be enabled
>>>>> when x2apic is needed by the system.
>>>>>
>>>>> The cause of the DMA fault is described in Bill's original version, and the
>>>>> INTR-Remap fault is caused by a similar reason. In short, the initialization
>>>>> of vt-d drivers causes the in-flight DMA and interrupt requests get wrong
>>>>> response.
>>>>>
>>>>> To fix this problem, we modifies the behaviors of the intel vt-d in the
>>>>> crashdump kernel:
>>>>>
>>>>> For DMA Remapping:
>>>>> 1. To accept the vt-d hardware in an active state,
>>>>> 2. Do not disable and re-enable the translation, keep it enabled.
>>>>> 3. Use the old root entry table, do not rewrite the RTA register.
>>>>> 4. Malloc and use new context entry table and page table, copy data from the
>>>>> old ones that used by the old kernel.
>>>>> 5. to use different portions of the iova address ranges for the device drivers
>>>>> in the crashdump kernel than the iova ranges that were in-use at the time
>>>>> of the panic.
>>>>> 6. After device driver is loaded, when it issues the first dma_map command,
>>>>> free the dmar_domain structure for this device, and generate a new one, so
>>>>> that the device can be assigned a new and empty page table.
>>>>> 7. When a new context entry table is generated, we also save its address to
>>>>> the old root entry table.
>>>>>
>>>>> For Interrupt Remapping:
>>>>> 1. To accept the vt-d hardware in an active state,
>>>>> 2. Do not disable and re-enable the interrupt remapping, keep it enabled.
>>>>> 3. Use the old interrupt remapping table, do not rewrite the IRTA register.
>>>>> 4. When ioapic entry is setup, the interrupt remapping table is changed, and
>>>>> the updated data will be stored to the old interrupt remapping table.
>>>>>
>>>>> Advantages of this approach:
>>>>> 1. All manipulation of the IO-device is done by the Linux device-driver
>>>>> for that device.
>>>>> 2. This approach behaves in a manner very similar to operation without an
>>>>> active iommu.
>>>>> 3. Any activity between the IO-device and its RMRR areas is handled by the
>>>>> device-driver in the same manner as during a non-kdump boot.
>>>>> 4. If an IO-device has no driver in the kdump kernel, it is simply left alone.
>>>>> This supports the practice of creating a special kdump kernel without
>>>>> drivers for any devices that are not required for taking a crashdump.
>>>>> 5. Minimal code-changes among the existing mainline intel vt-d code.
>>>>>
>>>>> Summary of changes in this patch set:
>>>>> 1. Added some useful function for root entry table in code intel-iommu.c
>>>>> 2. Added new members to struct root_entry and struct irte;
>>>>> 3. Functions to load old root entry table to iommu->root_entry from the memory
>>>>> of old kernel.
>>>>> 4. Functions to malloc new context entry table and page table and copy the data
>>>>> from the old ones to the malloced new ones.
>>>>> 5. Functions to enable support for DMA remapping in kdump kernel.
>>>>> 6. Functions to load old irte data from the old kernel to the kdump kernel.
>>>>> 7. Some code changes that support other behaviours that have been listed.
>>>>> 8. In the new functions, use physical address as "unsigned long" type, not
>>>>> pointers.
>>>>>
>>>>> Original version by Bill Sumner:
>>>>> https://lkml.org/lkml/2014/1/10/518
>>>>> https://lkml.org/lkml/2014/4/15/716
>>>>> https://lkml.org/lkml/2014/4/24/836
>>>>>
>>>>> Zhenhua's last of Bill's patchset:
>>>>> https://lkml.org/lkml/2014/10/21/134
>>>>> https://lkml.org/lkml/2014/12/15/121
>>>>>
>>>>> Changed in this version:
>>>>> 1. Do not disable and re-enable traslation and interrupt remapping.
>>>>> 2. Use old root entry table.
>>>>> 3. Use old interrupt remapping table.
>>>>> 4. Use "unsigned long" as physical address.
>>>>> 5. Use intel_unmap to unmap the old dma;
>>>>>
>>>>> This patchset should be applied with this one together:
>>>>> https://lkml.org/lkml/2014/11/5/43
>>>>> x86/iommu: fix incorrect bit operations in setting values
>>>>>
>>>>> Bill Sumner (5):
>>>>> iommu/vt-d: Update iommu_attach_domain() and its callers
>>>>> iommu/vt-d: Items required for kdump
>>>>> iommu/vt-d: data types and functions used for kdump
>>>>> iommu/vt-d: Add domain-id functions
>>>>> iommu/vt-d: enable kdump support in iommu module
>>>>>
>>>>> Li, Zhen-Hua (10):
>>>>> iommu/vt-d: Update iommu_attach_domain() and its callers
>>>>> iommu/vt-d: Items required for kdump
>>>>> iommu/vt-d: Add domain-id functions
>>>>> iommu/vt-d: functions to copy data from old mem
>>>>> iommu/vt-d: Add functions to load and save old re
>>>>> iommu/vt-d: datatypes and functions used for kdump
>>>>> iommu/vt-d: enable kdump support in iommu module
>>>>> iommu/vtd: assign new page table for dma_map
>>>>> iommu/vt-d: Copy functions for irte
>>>>> iommu/vt-d: Use old irte in kdump kernel
>>>>>
>>>>> drivers/iommu/intel-iommu.c | 1050 +++++++++++++++++++++++++++++++++--
>>>>> drivers/iommu/intel_irq_remapping.c | 99 +++-
>>>>> include/linux/intel-iommu.h | 18 +
>>>>> 3 files changed, 1123 insertions(+), 44 deletions(-)
>>>>>
>>>
>>>
>
