Hello, On Fri, Jan 02, 2009 at 08:10:50PM +0530, Jaswinder Singh Rajput wrote: > Hello all, > > Now I tested fealnx driver from 2.4.37 (2.4 git). I am still getting > "NETDEV WATCHDOG: eth0: transmit timed out". Please let me know how > can I fix this problem. Well, I don't have such an adapter, but most of the times I encountered a similar message with older 10/100 adapters, it was caused by a link status issue or duplex mismatch. Could you check with ethtool or mii-diag that the link status is correct and 100 Mbps/Full duplex (assuming you're connected to a switch) ? > fealnx.c:v2.51 Nov-17-2001 > eth0: 100/10M Ethernet PCI Adapter at 0x6200, 00:40:95:78:05:73, IRQ 11. > > NETDEV WATCHDOG: eth0: transmit timed out > eth0: Transmit timed out, status 00000000, resetting... > Rx ring c11bf000: 80000000 80000000 80000000 80000000 80000000 > 80000000 80000000 80000000 80000000 80000000 80000000 80000000 > Tx ring c11be000: 80000000 80000000 80000000 80000000 0000 80000000 > NETDEV WATCHDOG: eth0: transmit timed out > eth0: Transmit timed out, status 00000000, resetting... > Rx ring c11bf000: 80000000 80000000 80000000 80000000 80000000 > 80000000 80000000 80000000 80000000 80000000 80000000 80000000 > Tx ring c11be000: 80000000 0000 80000000 80000000 80000000 80000000 > NETDEV WATCHDOG: eth0: transmit timed out > eth0: Transmit timed out, status 00000000, resetting... > Rx ring c11bf000: 80000000 80000000 80000000 80000000 80000000 > 80000000 80000000 80000000 80000000 80000000 80000000 80000000 > Tx ring c11be000: 80000000 80000000 80000000 80000000 80000000 0000 > > > 00:0a.0 Ethernet controller: MYSON Technology Inc: Unknown device 0803 > Subsystem: MYSON Technology Inc: Unknown device 0803 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (8000ns min, 16000ns max), cache line size 08 > Interrupt: pin A routed to IRQ 11 > Region 0: I/O ports at 6200 [size=256] > Region 1: Memory at e1000000 (32-bit, non-prefetchable) [size=1K] > Expansion ROM at <unassigned> [disabled] [size=64K] > Capabilities: [88] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0-,D1+,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > Thank you, > JSR Regards, Willy -- To unsubscribe from this list: send the line "unsubscribe kernel-testers" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
