On Wed, 2015-10-14 at 14:44 +0200, Daniel Vetter wrote: > On Wed, Oct 14, 2015 at 11:21:46AM +0300, Ander Conselvan De Oliveira wrote: > > On Tue, 2015-10-13 at 16:08 +0200, Daniel Vetter wrote: > > > On Tue, Oct 13, 2015 at 04:00:37PM +0200, Maarten Lankhorst wrote: > > > > Op 13-10-15 om 15:58 schreef Daniel Vetter: > > > > > On Tue, Oct 13, 2015 at 03:43:28PM +0200, Maarten Lankhorst wrote: > > > > > > Op 13-10-15 om 15:35 schreef Daniel Vetter: > > > > > > > On Tue, Oct 13, 2015 at 03:18:16PM +0200, Maarten Lankhorst wrote: > > > > > > > > Op 23-09-15 om 17:34 schreef Gabriel Feceoru: > > > > > > > > > Using 2 connectors (DVI and VGA) will cause wrpll to be set for > > > > > > > > > INTEL_OUTPUT_HDMI but never reset if switching to INTEL_OUTPUT_VGA > > > > > > > > > > > > > > > > > > Supresses errors like these: > > > > > > > > > [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.wrpll > > > > > > > > > > > > > > > > > Looks like a good idea to always zero it. > > > > > > > Except that we still have a bunch of cases where we recompute clock state > > > > > > > but only partially. Can we just move them all up into a common place > > > > > > > please? That would also catch cases where we simply forget to fill this > > > > > > > out at all. > > > > > > > > > > > > > > One case I noticed is edp in skl_ddi_pll_select, but there's probably > > > > > > > more. > > > > > > > > > > > > > Something like below, with all the memsets for dpll_hw_state removed? > > > > > I think this will blow up since we recompute clock state only when > > > > > needs_modeset is true. So needs a bit more intelligence in deciding when > > > > > to clear it I think. > > > > Oops you're right. Maybe intel_modeset_clear_plls because that's where all the clock state > > > > belongs? > > > > > > Yeah that might be an even better place, in the loop after the continue; > > > statement. > > > > The reason I didn't put the memset there in the first place was the way we calculate plls for DP > > with DDI platforms. In that case, ddi_pll_sel is setup from the encoder_config instead of > > compute_clock, so a memset ends up clearing the new pll config. > > Hm, I forgot about this split totally. And there seems to be a giant mess > going on here: > > In our top-level intel_atomic_check we have 4 parts to compute state: > 1. drm_atomic_helper_check_modeset > 2. intel_modeset_pipe_config > 3. intel_modeset_checks > 4. drm_atomic_helper_check_planes > > We recalculate clocks (by calling dev_priv->display.crtc_compute_clock) > in 1., way ahead of anything else in intel_crtc_atomic_check. That looks > very suspcious since it means only very later on (in the loop that does > 2.) do we even decide whether we need to do a full modeset or not. > > So what I had in mind is that we clear clocks in > intel_modeset_pipe_config, before we call any of the callbacks. That makes > sure that when we decided to do a modeset, we do recompute the clocks > correctly. I had a suspicion this would interact badly with how we "cancel" the modeset if the pipe config didn't changed, just after the call to intel_modeset_pipe_config(). It turns out there's an issue there already. There are two possibilities for the dpll_hw_state value after the new pipe_config is calculated. It may have the new values already for DP in HSW/BDW and eDP in SKL or it may still have the old value. In the latter case the new value is only calculated in .crtc_clock(), after we already compared the old and new configs and may have decided to skip the modeset. But doing the memset() in intel_modeset_pipe_config() would be find as long as we don't change our minds about doing a modeset later. Ander _______________________________________________ Intel-gfx mailing list Intel-gfx@xxxxxxxxxxxxxxxxxxxxx http://lists.freedesktop.org/mailman/listinfo/intel-gfx
