Hi Daniel, hi Ville,
third attempt (-: This is a patch that enables dithering on the Fujitsu
S6010 installed NS2501 DVO. It also pulls out a couple of registers into
a separate structure, at least those registers of which I believe I know
what they do. Note that the NS2501 DVO is otherwise undocumented.
Tested on the S6010.
Greetings,
Thomas
Signed-off-by: Thomas Richter <thor@xxxxxxxxxxxxxxxxx>
This patch enables the (unfortunately undocumented) scaler of the
NatSemi 2501 DVO found in the Fujitsu-Siemens S6010 laptop and other
machines of the same series and age.
Parts of the DVO scaler logic have been revealed by reverse
engineering and trial and error, so your milage may vary. The
patch (and the whole ns2501 DVO code) is currently only good for
the 1024x768 panel of the S6010, and may hopefully work on other
machines with the same panel size.
The mode-specific configuration of the scaler have been moved out
into a separate class, the mode-agnostic settings remain as raw
register list as their purpose remains unclear at this point.
---
--- dvo_ns2501.c-org 2015-04-18 21:04:31.000000000 +0200
+++ dvo_ns2501.c 2015-04-18 20:46:00.000000000 +0200
@@ -60,6 +60,130 @@
#define NS2501_REGC 0x0c
+/*
+ * The following registers are not part of the official datasheet
+ * and are the result of reverse engineering.
+ */
+
+/*
+ * Register c0 controls how the DVO synchronizes with
+ * its input.
+ */
+#define NS2501_REGC0 0xc0
+#define NS2501_C0_ENABLE (1<<0) /* enable the DVO sync in general */
+#define NS2501_C0_HSYNC (1<<1) /* synchronize horizontal with input */
+#define NS2501_C0_VSYNC (1<<2) /* synchronize vertical with input */
+#define NS2501_C0_RESET (1<<7) /* reset the synchronization flip/flops */
+
+/*
+ * Register 41 is somehow related to the sync register and sync
+ * configuration. It should be 0x32 whenever regC0 is 0x05 (hsync off)
+ * and 0x00 otherwise.
+ */
+#define NS2501_REG41 0x41
+
+/*
+ * this register controls the dithering of the DVO
+ * One bit enables it, the other define the dithering depth.
+ * The higher the value, the lower the dithering depth.
+ */
+#define NS2501_F9_REG 0xf9
+#define NS2501_F9_ENABLE (1<<0) /* if set, dithering is enabled */
+#define NS2501_F9_DITHER_MASK (0x7f<<1) /* controls the dither depth */
+#define NS2501_F9_DITHER_SHIFT 1 /* shifts the dither mask */
+
+/*
+ * PLL configuration register. This is a pair of registers,
+ * one single byte register at 1B, and a pair at 1C,1D.
+ * These registers are counters/dividers.
+ */
+#define NS2501_REG1B 0x1b /* one byte PLL control register */
+#define NS2501_REG1C 0x1c /* low-part of the second register */
+#define NS2501_REG1D 0x1d /* high-part of the second register */
+
+/*
+ * Scaler control registers. Horizontal at b8,b9,
+ * vertical at 10,11. The scale factor is computed as
+ * 2^16/control-value. The low-byte comes first.
+ */
+#define NS2501_REG10 0x10 /* low-byte vertical scaler */
+#define NS2501_REG11 0x11 /* high-byte vertical scaler */
+#define NS2501_REGB8 0xb8 /* low-byte horizontal scaler */
+#define NS2501_REGB9 0xb9 /* high-byte horizontal scaler */
+
+/*
+ * Display window definition. This consists of four registers
+ * per dimension. One register pair defines the start of the
+ * display, one the end.
+ * As far as I understand, this defines the window within which
+ * the scaler samples the input.
+ */
+#define NS2501_REGC1 0xc1 /* low-byte horizontal display start */
+#define NS2501_REGC2 0xc2 /* high-byte horizontal display start */
+#define NS2501_REGC3 0xc3 /* low-byte horizontal display stop */
+#define NS2501_REGC4 0xc4 /* high-byte horizontal display stop */
+#define NS2501_REGC5 0xc5 /* low-byte vertical display start */
+#define NS2501_REGC6 0xc6 /* high-byte vertical display start */
+#define NS2501_REGC7 0xc7 /* low-byte vertical display stop */
+#define NS2501_REGC8 0xc8 /* high-byte vertical display stop */
+
+/*
+ * The following register pair seems to define the start of
+ * the vertical sync. If automatic syncing is enabled, and the
+ * register value defines a sync pulse that is later than the
+ * incoming sync, then the register value is ignored and the
+ * external hsync triggers the synchronization.
+ */
+#define NS2501_REG80 0x80 /* low-byte vsync-start */
+#define NS2501_REG81 0x81 /* high-byte vsync-start */
+
+/*
+ * The following register pair seems to define the total number
+ * of lines created at the output side of the scaler.
+ * This is again a low-high register pair.
+ */
+#define NS2501_REG82 0x82 /* output display height, low byte */
+#define NS2501_REG83 0x83 /* output display height, high byte */
+
+/*
+ * The following registers define the end of the front-porch
+ * in horizontal and vertical position and hence allow to shift
+ * the image left/right or up/down.
+ */
+#define NS2501_REG98 0x98 /* horizontal start of display + 256, low */
+#define NS2501_REG99 0x99 /* horizontal start of display + 256, high */
+#define NS2501_REG8E 0x8e /* vertical start of the display, low byte */
+#define NS2501_REG8F 0x8f /* vertical start of the display, high byte */
+
+/*
+ * The following register pair control the function of the
+ * backlight and the DVO output. To enable the corresponding
+ * function, the corresponding bit must be set in both registers.
+ */
+#define NS2501_REG34 0x34 /* DVO enable functions, first register */
+#define NS2501_REG35 0x35 /* DVO enable functions, second register */
+#define NS2501_34_ENABLE_OUTPUT (1<<0) /* enable DVO output */
+#define NS2501_34_ENABLE_BACKLIGHT (1<<1) /* enable backlight */
+
+/*
+ * Registers 9C and 9D define the vertical output offset
+ * of the visible region.
+ */
+#define NS2501_REG9C 0x9c
+#define NS2501_REG9D 0x9d
+
+/*
+ * The register 9F defines the dithering. This requires the
+ * scaler to be ON. Bit 0 enables dithering, the remaining
+ * bits control the depth of the dither. The higher the value,
+ * the LOWER the dithering amplitude. A good value seems to be
+ * 15 (total register value).
+ */
+#define NS2501_REGF9 0xf9
+#define NS2501_F9_ENABLE_DITHER (1<<0) /* enable dithering */
+#define NS2501_F9_DITHER_MASK (0x7f<<1) /* dither masking */
+#define NS2501_F9_DITHER_SHIFT 1 /* upshift of the dither mask */
+
enum {
MODE_640x480,
MODE_800x600,
@@ -72,274 +196,178 @@ struct ns2501_reg {
};
/*
- * Magic values based on what the BIOS on
- * Fujitsu-Siemens Lifebook S6010 programs (1024x768 panel).
+ * The following structure keeps the complete configuration of
+ * the DVO, given a specific output configuration.
+ * This is pretty much guess-work from reverse-engineering, so
+ * read all this with a grain of salt.
+ */
+struct ns2501_configuration {
+ uint8_t sync; /* configuration of the C0 register */
+ uint8_t conf; /* configuration register 8 */
+ uint8_t syncb; /* configuration register 41 */
+ uint8_t dither; /* configuration of the dithering */
+ uint8_t pll_a; /* PLL configuration, register A, 1B */
+ uint16_t pll_b; /* PLL configuration, register B, 1C/1D */
+ uint16_t hstart; /* horizontal start, registers C1/C2 */
+ uint16_t hstop; /* horizontal total, registers C3/C4 */
+ uint16_t vstart; /* vertical start, registers C5/C6 */
+ uint16_t vstop; /* vertical total, registers C7/C8 */
+ uint16_t vsync; /* manual vertical sync start, 80/81 */
+ uint16_t vtotal; /* number of lines generated, 82/83 */
+ uint16_t hpos; /* horizontal position + 256, 98/99 */
+ uint16_t vpos; /* vertical position, 8e/8f */
+ uint16_t voffs; /* vertical output offset, 9c/9d */
+ uint16_t hscale; /* horizontal scaling factor, b8/b9 */
+ uint16_t vscale; /* vertical scaling factor, 10/11 */
+};
+
+/*
+ * DVO configuration values, partially based on what the BIOS
+ * of the Fujitsu Lifebook S6010 writes into registers,
+ * partially found by manual tweaking. These configurations assume
+ * a 1024x768 panel.
*/
-static const struct ns2501_reg regs_1024x768[][86] = {
+static const struct ns2501_configuration ns2501_modes[] = {
[MODE_640x480] = {
- [0] = { .offset = 0x0a, .value = 0x81, },
- [1] = { .offset = 0x18, .value = 0x07, },
- [2] = { .offset = 0x19, .value = 0x00, },
- [3] = { .offset = 0x1a, .value = 0x00, },
- [4] = { .offset = 0x1b, .value = 0x11, },
- [5] = { .offset = 0x1c, .value = 0x54, },
- [6] = { .offset = 0x1d, .value = 0x03, },
- [7] = { .offset = 0x1e, .value = 0x02, },
- [8] = { .offset = 0xf3, .value = 0x90, },
- [9] = { .offset = 0xf9, .value = 0x00, },
- [10] = { .offset = 0xc1, .value = 0x90, },
- [11] = { .offset = 0xc2, .value = 0x00, },
- [12] = { .offset = 0xc3, .value = 0x0f, },
- [13] = { .offset = 0xc4, .value = 0x03, },
- [14] = { .offset = 0xc5, .value = 0x16, },
- [15] = { .offset = 0xc6, .value = 0x00, },
- [16] = { .offset = 0xc7, .value = 0x02, },
- [17] = { .offset = 0xc8, .value = 0x02, },
- [18] = { .offset = 0xf4, .value = 0x00, },
- [19] = { .offset = 0x80, .value = 0xff, },
- [20] = { .offset = 0x81, .value = 0x07, },
- [21] = { .offset = 0x82, .value = 0x3d, },
- [22] = { .offset = 0x83, .value = 0x05, },
- [23] = { .offset = 0x94, .value = 0x00, },
- [24] = { .offset = 0x95, .value = 0x00, },
- [25] = { .offset = 0x96, .value = 0x05, },
- [26] = { .offset = 0x97, .value = 0x00, },
- [27] = { .offset = 0x9a, .value = 0x88, },
- [28] = { .offset = 0x9b, .value = 0x00, },
- [29] = { .offset = 0x98, .value = 0x00, },
- [30] = { .offset = 0x99, .value = 0x00, },
- [31] = { .offset = 0xf7, .value = 0x88, },
- [32] = { .offset = 0xf8, .value = 0x0a, },
- [33] = { .offset = 0x9c, .value = 0x24, },
- [34] = { .offset = 0x9d, .value = 0x00, },
- [35] = { .offset = 0x9e, .value = 0x25, },
- [36] = { .offset = 0x9f, .value = 0x03, },
- [37] = { .offset = 0xa0, .value = 0x28, },
- [38] = { .offset = 0xa1, .value = 0x01, },
- [39] = { .offset = 0xa2, .value = 0x28, },
- [40] = { .offset = 0xa3, .value = 0x05, },
- [41] = { .offset = 0xb6, .value = 0x09, },
- [42] = { .offset = 0xb8, .value = 0x00, },
- [43] = { .offset = 0xb9, .value = 0xa0, },
- [44] = { .offset = 0xba, .value = 0x00, },
- [45] = { .offset = 0xbb, .value = 0x20, },
- [46] = { .offset = 0x10, .value = 0x00, },
- [47] = { .offset = 0x11, .value = 0xa0, },
- [48] = { .offset = 0x12, .value = 0x02, },
- [49] = { .offset = 0x20, .value = 0x00, },
- [50] = { .offset = 0x22, .value = 0x00, },
- [51] = { .offset = 0x23, .value = 0x00, },
- [52] = { .offset = 0x24, .value = 0x00, },
- [53] = { .offset = 0x25, .value = 0x00, },
- [54] = { .offset = 0x8c, .value = 0x10, },
- [55] = { .offset = 0x8d, .value = 0x02, },
- [56] = { .offset = 0x8e, .value = 0x10, },
- [57] = { .offset = 0x8f, .value = 0x00, },
- [58] = { .offset = 0x90, .value = 0xff, },
- [59] = { .offset = 0x91, .value = 0x07, },
- [60] = { .offset = 0x92, .value = 0xa0, },
- [61] = { .offset = 0x93, .value = 0x02, },
- [62] = { .offset = 0xa5, .value = 0x00, },
- [63] = { .offset = 0xa6, .value = 0x00, },
- [64] = { .offset = 0xa7, .value = 0x00, },
- [65] = { .offset = 0xa8, .value = 0x00, },
- [66] = { .offset = 0xa9, .value = 0x04, },
- [67] = { .offset = 0xaa, .value = 0x70, },
- [68] = { .offset = 0xab, .value = 0x4f, },
- [69] = { .offset = 0xac, .value = 0x00, },
- [70] = { .offset = 0xa4, .value = 0x84, },
- [71] = { .offset = 0x7e, .value = 0x18, },
- [72] = { .offset = 0x84, .value = 0x00, },
- [73] = { .offset = 0x85, .value = 0x00, },
- [74] = { .offset = 0x86, .value = 0x00, },
- [75] = { .offset = 0x87, .value = 0x00, },
- [76] = { .offset = 0x88, .value = 0x00, },
- [77] = { .offset = 0x89, .value = 0x00, },
- [78] = { .offset = 0x8a, .value = 0x00, },
- [79] = { .offset = 0x8b, .value = 0x00, },
- [80] = { .offset = 0x26, .value = 0x00, },
- [81] = { .offset = 0x27, .value = 0x00, },
- [82] = { .offset = 0xad, .value = 0x00, },
- [83] = { .offset = 0x08, .value = 0x30, }, /* 0x31 */
- [84] = { .offset = 0x41, .value = 0x00, },
- [85] = { .offset = 0xc0, .value = 0x05, },
+ .sync = NS2501_C0_ENABLE | NS2501_C0_VSYNC,
+ .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
+ .syncb = 0x32,
+ .dither = 0x0f,
+ .pll_a = 17,
+ .pll_b = 852,
+ .hstart = 144,
+ .hstop = 783,
+ .vstart = 22,
+ .vstop = 514,
+ .vsync = 2047, /* actually, ignored with this config */
+ .vtotal = 1341,
+ .hpos = 0,
+ .vpos = 16,
+ .voffs = 36,
+ .hscale = 40960,
+ .vscale = 40960
},
[MODE_800x600] = {
- [0] = { .offset = 0x0a, .value = 0x81, },
- [1] = { .offset = 0x18, .value = 0x07, },
- [2] = { .offset = 0x19, .value = 0x00, },
- [3] = { .offset = 0x1a, .value = 0x00, },
- [4] = { .offset = 0x1b, .value = 0x19, },
- [5] = { .offset = 0x1c, .value = 0x64, },
- [6] = { .offset = 0x1d, .value = 0x02, },
- [7] = { .offset = 0x1e, .value = 0x02, },
- [8] = { .offset = 0xf3, .value = 0x90, },
- [9] = { .offset = 0xf9, .value = 0x00, },
- [10] = { .offset = 0xc1, .value = 0xd7, },
- [11] = { .offset = 0xc2, .value = 0x00, },
- [12] = { .offset = 0xc3, .value = 0xf8, },
- [13] = { .offset = 0xc4, .value = 0x03, },
- [14] = { .offset = 0xc5, .value = 0x1a, },
- [15] = { .offset = 0xc6, .value = 0x00, },
- [16] = { .offset = 0xc7, .value = 0x73, },
- [17] = { .offset = 0xc8, .value = 0x02, },
- [18] = { .offset = 0xf4, .value = 0x00, },
- [19] = { .offset = 0x80, .value = 0x27, },
- [20] = { .offset = 0x81, .value = 0x03, },
- [21] = { .offset = 0x82, .value = 0x41, },
- [22] = { .offset = 0x83, .value = 0x05, },
- [23] = { .offset = 0x94, .value = 0x00, },
- [24] = { .offset = 0x95, .value = 0x00, },
- [25] = { .offset = 0x96, .value = 0x05, },
- [26] = { .offset = 0x97, .value = 0x00, },
- [27] = { .offset = 0x9a, .value = 0x88, },
- [28] = { .offset = 0x9b, .value = 0x00, },
- [29] = { .offset = 0x98, .value = 0x00, },
- [30] = { .offset = 0x99, .value = 0x00, },
- [31] = { .offset = 0xf7, .value = 0x88, },
- [32] = { .offset = 0xf8, .value = 0x06, },
- [33] = { .offset = 0x9c, .value = 0x23, },
- [34] = { .offset = 0x9d, .value = 0x00, },
- [35] = { .offset = 0x9e, .value = 0x25, },
- [36] = { .offset = 0x9f, .value = 0x03, },
- [37] = { .offset = 0xa0, .value = 0x28, },
- [38] = { .offset = 0xa1, .value = 0x01, },
- [39] = { .offset = 0xa2, .value = 0x28, },
- [40] = { .offset = 0xa3, .value = 0x05, },
- [41] = { .offset = 0xb6, .value = 0x09, },
- [42] = { .offset = 0xb8, .value = 0x30, },
- [43] = { .offset = 0xb9, .value = 0xc8, },
- [44] = { .offset = 0xba, .value = 0x00, },
- [45] = { .offset = 0xbb, .value = 0x20, },
- [46] = { .offset = 0x10, .value = 0x20, },
- [47] = { .offset = 0x11, .value = 0xc8, },
- [48] = { .offset = 0x12, .value = 0x02, },
- [49] = { .offset = 0x20, .value = 0x00, },
- [50] = { .offset = 0x22, .value = 0x00, },
- [51] = { .offset = 0x23, .value = 0x00, },
- [52] = { .offset = 0x24, .value = 0x00, },
- [53] = { .offset = 0x25, .value = 0x00, },
- [54] = { .offset = 0x8c, .value = 0x10, },
- [55] = { .offset = 0x8d, .value = 0x02, },
- [56] = { .offset = 0x8e, .value = 0x04, },
- [57] = { .offset = 0x8f, .value = 0x00, },
- [58] = { .offset = 0x90, .value = 0xff, },
- [59] = { .offset = 0x91, .value = 0x07, },
- [60] = { .offset = 0x92, .value = 0xa0, },
- [61] = { .offset = 0x93, .value = 0x02, },
- [62] = { .offset = 0xa5, .value = 0x00, },
- [63] = { .offset = 0xa6, .value = 0x00, },
- [64] = { .offset = 0xa7, .value = 0x00, },
- [65] = { .offset = 0xa8, .value = 0x00, },
- [66] = { .offset = 0xa9, .value = 0x83, },
- [67] = { .offset = 0xaa, .value = 0x40, },
- [68] = { .offset = 0xab, .value = 0x32, },
- [69] = { .offset = 0xac, .value = 0x00, },
- [70] = { .offset = 0xa4, .value = 0x80, },
- [71] = { .offset = 0x7e, .value = 0x18, },
- [72] = { .offset = 0x84, .value = 0x00, },
- [73] = { .offset = 0x85, .value = 0x00, },
- [74] = { .offset = 0x86, .value = 0x00, },
- [75] = { .offset = 0x87, .value = 0x00, },
- [76] = { .offset = 0x88, .value = 0x00, },
- [77] = { .offset = 0x89, .value = 0x00, },
- [78] = { .offset = 0x8a, .value = 0x00, },
- [79] = { .offset = 0x8b, .value = 0x00, },
- [80] = { .offset = 0x26, .value = 0x00, },
- [81] = { .offset = 0x27, .value = 0x00, },
- [82] = { .offset = 0xad, .value = 0x00, },
- [83] = { .offset = 0x08, .value = 0x30, }, /* 0x31 */
- [84] = { .offset = 0x41, .value = 0x00, },
- [85] = { .offset = 0xc0, .value = 0x07, },
+ .sync = NS2501_C0_ENABLE |
+ NS2501_C0_HSYNC | NS2501_C0_VSYNC,
+ .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
+ .syncb = 0x00,
+ .dither = 0x0f,
+ .pll_a = 25,
+ .pll_b = 612,
+ .hstart = 215,
+ .hstop = 1016,
+ .vstart = 26,
+ .vstop = 627,
+ .vsync = 807,
+ .vtotal = 1341,
+ .hpos = 0,
+ .vpos = 4,
+ .voffs = 35,
+ .hscale = 51248,
+ .vscale = 51232
},
[MODE_1024x768] = {
- [0] = { .offset = 0x0a, .value = 0x81, },
- [1] = { .offset = 0x18, .value = 0x07, },
- [2] = { .offset = 0x19, .value = 0x00, },
- [3] = { .offset = 0x1a, .value = 0x00, },
- [4] = { .offset = 0x1b, .value = 0x11, },
- [5] = { .offset = 0x1c, .value = 0x54, },
- [6] = { .offset = 0x1d, .value = 0x03, },
- [7] = { .offset = 0x1e, .value = 0x02, },
- [8] = { .offset = 0xf3, .value = 0x90, },
- [9] = { .offset = 0xf9, .value = 0x00, },
- [10] = { .offset = 0xc1, .value = 0x90, },
- [11] = { .offset = 0xc2, .value = 0x00, },
- [12] = { .offset = 0xc3, .value = 0x0f, },
- [13] = { .offset = 0xc4, .value = 0x03, },
- [14] = { .offset = 0xc5, .value = 0x16, },
- [15] = { .offset = 0xc6, .value = 0x00, },
- [16] = { .offset = 0xc7, .value = 0x02, },
- [17] = { .offset = 0xc8, .value = 0x02, },
- [18] = { .offset = 0xf4, .value = 0x00, },
- [19] = { .offset = 0x80, .value = 0xff, },
- [20] = { .offset = 0x81, .value = 0x07, },
- [21] = { .offset = 0x82, .value = 0x3d, },
- [22] = { .offset = 0x83, .value = 0x05, },
- [23] = { .offset = 0x94, .value = 0x00, },
- [24] = { .offset = 0x95, .value = 0x00, },
- [25] = { .offset = 0x96, .value = 0x05, },
- [26] = { .offset = 0x97, .value = 0x00, },
- [27] = { .offset = 0x9a, .value = 0x88, },
- [28] = { .offset = 0x9b, .value = 0x00, },
- [29] = { .offset = 0x98, .value = 0x00, },
- [30] = { .offset = 0x99, .value = 0x00, },
- [31] = { .offset = 0xf7, .value = 0x88, },
- [32] = { .offset = 0xf8, .value = 0x0a, },
- [33] = { .offset = 0x9c, .value = 0x24, },
- [34] = { .offset = 0x9d, .value = 0x00, },
- [35] = { .offset = 0x9e, .value = 0x25, },
- [36] = { .offset = 0x9f, .value = 0x03, },
- [37] = { .offset = 0xa0, .value = 0x28, },
- [38] = { .offset = 0xa1, .value = 0x01, },
- [39] = { .offset = 0xa2, .value = 0x28, },
- [40] = { .offset = 0xa3, .value = 0x05, },
- [41] = { .offset = 0xb6, .value = 0x09, },
- [42] = { .offset = 0xb8, .value = 0x00, },
- [43] = { .offset = 0xb9, .value = 0xa0, },
- [44] = { .offset = 0xba, .value = 0x00, },
- [45] = { .offset = 0xbb, .value = 0x20, },
- [46] = { .offset = 0x10, .value = 0x00, },
- [47] = { .offset = 0x11, .value = 0xa0, },
- [48] = { .offset = 0x12, .value = 0x02, },
- [49] = { .offset = 0x20, .value = 0x00, },
- [50] = { .offset = 0x22, .value = 0x00, },
- [51] = { .offset = 0x23, .value = 0x00, },
- [52] = { .offset = 0x24, .value = 0x00, },
- [53] = { .offset = 0x25, .value = 0x00, },
- [54] = { .offset = 0x8c, .value = 0x10, },
- [55] = { .offset = 0x8d, .value = 0x02, },
- [56] = { .offset = 0x8e, .value = 0x10, },
- [57] = { .offset = 0x8f, .value = 0x00, },
- [58] = { .offset = 0x90, .value = 0xff, },
- [59] = { .offset = 0x91, .value = 0x07, },
- [60] = { .offset = 0x92, .value = 0xa0, },
- [61] = { .offset = 0x93, .value = 0x02, },
- [62] = { .offset = 0xa5, .value = 0x00, },
- [63] = { .offset = 0xa6, .value = 0x00, },
- [64] = { .offset = 0xa7, .value = 0x00, },
- [65] = { .offset = 0xa8, .value = 0x00, },
- [66] = { .offset = 0xa9, .value = 0x04, },
- [67] = { .offset = 0xaa, .value = 0x70, },
- [68] = { .offset = 0xab, .value = 0x4f, },
- [69] = { .offset = 0xac, .value = 0x00, },
- [70] = { .offset = 0xa4, .value = 0x84, },
- [71] = { .offset = 0x7e, .value = 0x18, },
- [72] = { .offset = 0x84, .value = 0x00, },
- [73] = { .offset = 0x85, .value = 0x00, },
- [74] = { .offset = 0x86, .value = 0x00, },
- [75] = { .offset = 0x87, .value = 0x00, },
- [76] = { .offset = 0x88, .value = 0x00, },
- [77] = { .offset = 0x89, .value = 0x00, },
- [78] = { .offset = 0x8a, .value = 0x00, },
- [79] = { .offset = 0x8b, .value = 0x00, },
- [80] = { .offset = 0x26, .value = 0x00, },
- [81] = { .offset = 0x27, .value = 0x00, },
- [82] = { .offset = 0xad, .value = 0x00, },
- [83] = { .offset = 0x08, .value = 0x34, }, /* 0x35 */
- [84] = { .offset = 0x41, .value = 0x00, },
- [85] = { .offset = 0xc0, .value = 0x01, },
- },
+ .sync = NS2501_C0_ENABLE | NS2501_C0_VSYNC,
+ .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
+ .syncb = 0x32,
+ .dither = 0x0f,
+ .pll_a = 11,
+ .pll_b = 1350,
+ .hstart = 276,
+ .hstop = 1299,
+ .vstart = 15,
+ .vstop = 1056,
+ .vsync = 2047,
+ .vtotal = 1341,
+ .hpos = 0,
+ .vpos = 7,
+ .voffs = 27,
+ .hscale = 65535,
+ .vscale = 65535
+ }
+};
+
+/*
+ * Other configuration values left by the BIOS of the
+ * Fujitsu S6010 in the DVO control registers. Their
+ * value does not depend on the BIOS and their meaning
+ * is unknown.
+ */
+
+static const struct ns2501_reg mode_agnostic_values[] = {
+ /* 08 is mode specific */
+ [0] = { .offset = 0x0a, .value = 0x81, },
+ /* 10,11 are part of the mode specific configuration */
+ [1] = { .offset = 0x12, .value = 0x02, },
+ [2] = { .offset = 0x18, .value = 0x07, },
+ [3] = { .offset = 0x19, .value = 0x00, },
+ [4] = { .offset = 0x1a, .value = 0x00, }, /* PLL?, ignored */
+ /* 1b,1c,1d are part of the mode specific configuration */
+ [5] = { .offset = 0x1e, .value = 0x02, },
+ [6] = { .offset = 0x1f, .value = 0x40, },
+ [7] = { .offset = 0x20, .value = 0x00, },
+ [8] = { .offset = 0x21, .value = 0x00, },
+ [9] = { .offset = 0x22, .value = 0x00, },
+ [10] = { .offset = 0x23, .value = 0x00, },
+ [11] = { .offset = 0x24, .value = 0x00, },
+ [12] = { .offset = 0x25, .value = 0x00, },
+ [13] = { .offset = 0x26, .value = 0x00, },
+ [14] = { .offset = 0x27, .value = 0x00, },
+ [15] = { .offset = 0x7e, .value = 0x18, },
+ /* 80-84 are part of the mode-specific configuration */
+ [16] = { .offset = 0x84, .value = 0x00, },
+ [17] = { .offset = 0x85, .value = 0x00, },
+ [18] = { .offset = 0x86, .value = 0x00, },
+ [19] = { .offset = 0x87, .value = 0x00, },
+ [20] = { .offset = 0x88, .value = 0x00, },
+ [21] = { .offset = 0x89, .value = 0x00, },
+ [22] = { .offset = 0x8a, .value = 0x00, },
+ [23] = { .offset = 0x8b, .value = 0x00, },
+ [24] = { .offset = 0x8c, .value = 0x10, },
+ [25] = { .offset = 0x8d, .value = 0x02, },
+ /* 8e,8f are part of the mode-specific configuration */
+ [26] = { .offset = 0x90, .value = 0xff, },
+ [27] = { .offset = 0x91, .value = 0x07, },
+ [28] = { .offset = 0x92, .value = 0xa0, },
+ [29] = { .offset = 0x93, .value = 0x02, },
+ [30] = { .offset = 0x94, .value = 0x00, },
+ [31] = { .offset = 0x95, .value = 0x00, },
+ [32] = { .offset = 0x96, .value = 0x05, },
+ [33] = { .offset = 0x97, .value = 0x00, },
+ /* 98,99 are part of the mode-specific configuration */
+ [34] = { .offset = 0x9a, .value = 0x88, },
+ [35] = { .offset = 0x9b, .value = 0x00, },
+ /* 9c,9d are part of the mode-specific configuration */
+ [36] = { .offset = 0x9e, .value = 0x25, },
+ [37] = { .offset = 0x9f, .value = 0x03, },
+ [38] = { .offset = 0xa0, .value = 0x28, },
+ [39] = { .offset = 0xa1, .value = 0x01, },
+ [40] = { .offset = 0xa2, .value = 0x28, },
+ [41] = { .offset = 0xa3, .value = 0x05, },
+ /* register 0xa4 is mode specific, but 0x80..0x84 works always */
+ [42] = { .offset = 0xa4, .value = 0x84, },
+ [43] = { .offset = 0xa5, .value = 0x00, },
+ [44] = { .offset = 0xa6, .value = 0x00, },
+ [45] = { .offset = 0xa7, .value = 0x00, },
+ [46] = { .offset = 0xa8, .value = 0x00, },
+ /* 0xa9 to 0xab are mode specific, but have no visible effect */
+ [47] = { .offset = 0xa9, .value = 0x04, },
+ [48] = { .offset = 0xaa, .value = 0x70, },
+ [49] = { .offset = 0xab, .value = 0x4f, },
+ [50] = { .offset = 0xac, .value = 0x00, },
+ [51] = { .offset = 0xad, .value = 0x00, },
+ [52] = { .offset = 0xb6, .value = 0x09, },
+ [53] = { .offset = 0xb7, .value = 0x03, },
+ /* b8,b9 are part of the mode-specific configuration */
+ [54] = { .offset = 0xba, .value = 0x00, },
+ [55] = { .offset = 0xbb, .value = 0x20, },
+ [56] = { .offset = 0xf3, .value = 0x90, },
+ [57] = { .offset = 0xf4, .value = 0x00, },
+ [58] = { .offset = 0xf7, .value = 0x88, },
+ /* f8 is mode specific, but the value does not matter */
+ [59] = { .offset = 0xf8, .value = 0x0a, },
+ [60] = { .offset = 0xf9, .value = 0x00, }
};
static const struct ns2501_reg regs_init[] = {
@@ -350,25 +378,12 @@ static const struct ns2501_reg regs_init
struct ns2501_priv {
bool quiet;
- const struct ns2501_reg *regs;
+ const struct ns2501_configuration *conf;
};
#define NSPTR(d) ((NS2501Ptr)(d->DriverPrivate.ptr))
/*
- * For reasons unclear to me, the ns2501 at least on the Fujitsu/Siemens
- * laptops does not react on the i2c bus unless
- * both the PLL is running and the display is configured in its native
- * resolution.
- * This function forces the DVO on, and stores the registers it touches.
- * Afterwards, registers are restored to regular values.
- *
- * This is pretty much a hack, though it works.
- * Without that, ns2501_readb and ns2501_writeb fail
- * when switching the resolution.
- */
-
-/*
** Read a register from the ns2501.
** Returns true if successful, false otherwise.
** If it returns false, it might be wise to enable the
@@ -534,6 +549,7 @@ static void ns2501_mode_set(struct intel
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode)
{
+ const struct ns2501_configuration *conf;
struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
int mode_idx, i;
@@ -541,6 +557,36 @@ static void ns2501_mode_set(struct intel
("set mode (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d).\n",
mode->hdisplay, mode->htotal, mode->vdisplay, mode->vtotal);
+ DRM_DEBUG_KMS("Detailed requested mode settings are:\n"
+ "clock : %d kHz\n"
+ "hdisplay : %d\n"
+ "hblank start : %d\n"
+ "hblank end : %d\n"
+ "hsync start : %d\n"
+ "hsync end : %d\n"
+ "htotal : %d\n"
+ "hskew : %d\n"
+ "vdisplay : %d\n"
+ "vblank start : %d\n"
+ "hblank end : %d\n"
+ "vsync start : %d\n"
+ "vsync end : %d\n"
+ "vtotal : %d\n",
+ adjusted_mode->crtc_clock,
+ adjusted_mode->crtc_hdisplay,
+ adjusted_mode->crtc_hblank_start,
+ adjusted_mode->crtc_hblank_end,
+ adjusted_mode->crtc_hsync_start,
+ adjusted_mode->crtc_hsync_end,
+ adjusted_mode->crtc_htotal,
+ adjusted_mode->crtc_hskew,
+ adjusted_mode->crtc_vdisplay,
+ adjusted_mode->crtc_vblank_start,
+ adjusted_mode->crtc_vblank_end,
+ adjusted_mode->crtc_vsync_start,
+ adjusted_mode->crtc_vsync_end,
+ adjusted_mode->crtc_vtotal);
+
if (mode->hdisplay == 640 && mode->vdisplay == 480)
mode_idx = MODE_640x480;
else if (mode->hdisplay == 800 && mode->vdisplay == 600)
@@ -554,10 +600,44 @@ static void ns2501_mode_set(struct intel
for (i = 0; i < ARRAY_SIZE(regs_init); i++)
ns2501_writeb(dvo, regs_init[i].offset, regs_init[i].value);
- ns->regs = regs_1024x768[mode_idx];
-
- for (i = 0; i < 84; i++)
- ns2501_writeb(dvo, ns->regs[i].offset, ns->regs[i].value);
+ /* Write the mode-agnostic values */
+ for (i = 0; i < ARRAY_SIZE(mode_agnostic_values); i++)
+ ns2501_writeb(dvo, mode_agnostic_values[i].offset,
+ mode_agnostic_values[i].value);
+
+ /* Write now the mode-specific configuration */
+ conf = ns2501_modes + mode_idx;
+ ns->conf = conf;
+
+ ns2501_writeb(dvo, NS2501_REG8, conf->conf);
+ ns2501_writeb(dvo, NS2501_REG1B, conf->pll_a);
+ ns2501_writeb(dvo, NS2501_REG1C, conf->pll_b & 0xff);
+ ns2501_writeb(dvo, NS2501_REG1D, conf->pll_b >> 8);
+ ns2501_writeb(dvo, NS2501_REGC1, conf->hstart & 0xff);
+ ns2501_writeb(dvo, NS2501_REGC2, conf->hstart >> 8);
+ ns2501_writeb(dvo, NS2501_REGC3, conf->hstop & 0xff);
+ ns2501_writeb(dvo, NS2501_REGC4, conf->hstop >> 8);
+ ns2501_writeb(dvo, NS2501_REGC5, conf->vstart & 0xff);
+ ns2501_writeb(dvo, NS2501_REGC6, conf->vstart >> 8);
+ ns2501_writeb(dvo, NS2501_REGC7, conf->vstop & 0xff);
+ ns2501_writeb(dvo, NS2501_REGC8, conf->vstop >> 8);
+ ns2501_writeb(dvo, NS2501_REG80, conf->vsync & 0xff);
+ ns2501_writeb(dvo, NS2501_REG81, conf->vsync >> 8);
+ ns2501_writeb(dvo, NS2501_REG82, conf->vtotal & 0xff);
+ ns2501_writeb(dvo, NS2501_REG83, conf->vtotal >> 8);
+ ns2501_writeb(dvo, NS2501_REG98, conf->hpos & 0xff);
+ ns2501_writeb(dvo, NS2501_REG99, conf->hpos >> 8);
+ ns2501_writeb(dvo, NS2501_REG8E, conf->vpos & 0xff);
+ ns2501_writeb(dvo, NS2501_REG8F, conf->vpos >> 8);
+ ns2501_writeb(dvo, NS2501_REG9C, conf->voffs & 0xff);
+ ns2501_writeb(dvo, NS2501_REG9D, conf->voffs >> 8);
+ ns2501_writeb(dvo, NS2501_REGB8, conf->hscale & 0xff);
+ ns2501_writeb(dvo, NS2501_REGB9, conf->hscale >> 8);
+ ns2501_writeb(dvo, NS2501_REG10, conf->vscale & 0xff);
+ ns2501_writeb(dvo, NS2501_REG11, conf->vscale >> 8);
+ ns2501_writeb(dvo, NS2501_REGF9, conf->dither);
+ ns2501_writeb(dvo, NS2501_REG41, conf->syncb);
+ ns2501_writeb(dvo, NS2501_REGC0, conf->sync);
}
/* set the NS2501 power state */
@@ -579,34 +659,32 @@ static void ns2501_dpms(struct intel_dvo
DRM_DEBUG_KMS("Trying set the dpms of the DVO to %i\n", enable);
if (enable) {
- if (WARN_ON(ns->regs[83].offset != 0x08 ||
- ns->regs[84].offset != 0x41 ||
- ns->regs[85].offset != 0xc0))
- return;
-
- ns2501_writeb(dvo, 0xc0, ns->regs[85].value | 0x08);
+ ns2501_writeb(dvo, NS2501_REGC0, ns->conf->sync | 0x08);
- ns2501_writeb(dvo, 0x41, ns->regs[84].value);
+ ns2501_writeb(dvo, NS2501_REG41, ns->conf->syncb);
- ns2501_writeb(dvo, 0x34, 0x01);
+ ns2501_writeb(dvo, NS2501_REG34, NS2501_34_ENABLE_OUTPUT);
msleep(15);
- ns2501_writeb(dvo, 0x08, 0x35);
- if (!(ns->regs[83].value & NS2501_8_BPAS))
- ns2501_writeb(dvo, 0x08, 0x31);
+ ns2501_writeb(dvo, NS2501_REG8,
+ ns->conf->conf | NS2501_8_BPAS);
+ if (!(ns->conf->conf & NS2501_8_BPAS))
+ ns2501_writeb(dvo, NS2501_REG8, ns->conf->conf);
msleep(200);
- ns2501_writeb(dvo, 0x34, 0x03);
+ ns2501_writeb(dvo, NS2501_REG34,
+ NS2501_34_ENABLE_OUTPUT | NS2501_34_ENABLE_BACKLIGHT);
- ns2501_writeb(dvo, 0xc0, ns->regs[85].value);
+ ns2501_writeb(dvo, NS2501_REGC0, ns->conf->sync);
} else {
- ns2501_writeb(dvo, 0x34, 0x01);
+ ns2501_writeb(dvo, NS2501_REG34, NS2501_34_ENABLE_OUTPUT);
msleep(200);
- ns2501_writeb(dvo, 0x08, 0x34);
+ ns2501_writeb(dvo, NS2501_REG8, NS2501_8_VEN | NS2501_8_HEN |
+ NS2501_8_BPAS);
msleep(15);
- ns2501_writeb(dvo, 0x34, 0x00);
+ ns2501_writeb(dvo, NS2501_REG34, 0x00);
}
}
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
