Re: [PATCH] drm/i915/vlv: drop punit freq staus read after setting idle

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Jun 12, 2014 at 03:37:18PM +0800, Lee, Chon Ming wrote:
> On 06/12 08:14, S, Deepak wrote:
> > 
> > 
> > On 6/11/2014 10:26 PM, Ville Syrjälä wrote:
> > >On Fri, Jun 06, 2014 at 08:03:20AM -0700, Jesse Barnes wrote:
> > >>On Fri, 6 Jun 2014 11:29:24 +0300
> > >>Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx> wrote:
> > >>
> > >>>On Thu, Jun 05, 2014 at 01:49:34PM -0700, Jesse Barnes wrote:
> > >>>>This may take awhile (~10ms), and we don't need to make noise about it.
> > >>>>
> > >>>>References: https://bugs.freedesktop.org/show_bug.cgi?id=75244
> > >>>>Tested-by: huax.lu@xxxxxxxxx
> > >>>>Signed-off-by: Jesse Barnes <jbarnes@xxxxxxxxxxxxxxxx>
> > >>>>---
> > >>>>  drivers/gpu/drm/i915/intel_pm.c | 4 ----
> > >>>>  1 file changed, 4 deletions(-)
> > >>>>
> > >>>>diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
> > >>>>index ee27d74..4eebfd8 100644
> > >>>>--- a/drivers/gpu/drm/i915/intel_pm.c
> > >>>>+++ b/drivers/gpu/drm/i915/intel_pm.c
> > >>>>@@ -3227,10 +3227,6 @@ static void vlv_set_rps_idle(struct drm_i915_private *dev_priv)
> > >>>>  	vlv_punit_write(dev_priv, PUNIT_REG_GPU_FREQ_REQ,
> > >>>>  					dev_priv->rps.min_freq_softlimit);
> > >>>>
> > >>>>-	if (wait_for(((vlv_punit_read(dev_priv, PUNIT_REG_GPU_FREQ_STS))
> > >>>>-				& GENFREQSTATUS) == 0, 5))
> > >>>>-		DRM_ERROR("timed out waiting for Punit\n");
> > >>>>-
> > >>>
> > >>>As I recall the entire point of this was to make sure the frequency
> > >>>really drops before we allow turning off the clock. I'm not sure if we
> > >>>can trust that the frequency (and more importantly the voltage) will
> > >>>drop if we allow turning off the clock before the transition is
> > >>>complete.
> > >>
> > >>well, we may need to increase the timeout then... let's see if that
> > >>helps with the bug.
> > >
> > >FYI I played around with my BYT a bit and it doesn't appear to require
> > >this "force gfx clock on" part of the workaround.
> > >
> > >I was polling VLV_GTLC_SURVIVABILITY_REG and VLV_GTLC_PW_STATUS to make
> > >sure both render and media wells and the gfx clock remain off, and I
> > >was also monitoring vnn via svid. While that was going on I just rewrote
> > >PUNIT_REG_GPU_FREQ_REQ to make Punit change the frequency, and sure
> > >enough it did, and svid showed me that vnn had also changed. So it
> > >appears there's no need to have the gfx clock on to change its frequency
> > >on this BYT.
> > >
> > >I wonder if this part of the workaround was only needed on older parts.
> > >Deepak, any ideas?
> > 
> > Yes ville, this was added initial for older parts and force gfx
> > clock was part of the workaround.
> > We have not verified this on newer parts. Let me check with hw guys
> > to see if workaround still exits and when this was fixed.
> > 
> > Thanks
> > Deepak
> 
> This is a bit side topic.  In the vlv_set_rps_idle, it try to mask the turbo
> interrupt by writing to GEN6_PMINTRMSK (offset 0xA168).  But based on the bspec,
> the PMIMR for BYT/GEN6 should be 0x44024 (GEN6_PMIMR).  
> 
> Not sure I miss anything.  If there offset is wrong, mean the turbo has not mask at
> all.

There are two mask registers for this stuff. PMINTRMSK is some kind
of lower level mask, and GEN6_PMIMR is the regular interrupt mask.
I believe masking the interrupt in PMINTRMSK prevents it from being
visible in GEN6_PMISR even.

-- 
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx





[Index of Archives]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]
  Powered by Linux