Even though the VRR timing generator (TG) is primarily used for
variable refresh rates, it can be used for fixed refresh rates as
well. For a fixed refresh rate the Flip Line and Vmax must be equal
(TRANS_VRR_FLIPLINE = TRANS_VRR_VMAX). Beyond that, there are some
dependencies between the VRR timings and the legacy timing generator
registers.
This series is an attempt to use VRR TG for fixed refresh rate.
For platforms XE2LPD+, always go with VRR timing generator for both fixed and
variable refresh rate cases.
Rev2:
-Added support from MTL+ and for HDMI too.
-Changed VRR VSYNC programming which is required for HDMI.
-Modified vrr compute config for bigjoiner case. (Still to be tested).
Rev3:
-Start support from XE2LPD+ as MTL needs a WA to have PSR +VRR (fixed
refresh rate)
-Add changes to enable PSR with VRR with fixed refresh rate.
Rev4:
-Addressed review comments from Mitul and rebased.
Rev5:
-Avoid MSA Ignore PAR timing enable bit for fixed refresh rate
with VRR TG.
-Skip VRR compute config for HDMI connected via DP-HDMI2.1 PCON.
-Print fixed_rr along with other VRR parameters in crtc state dump.
-Rebase
Rev6:
-Refactor VRR code to have distinct modes in which VRR timing generator
can be used: VRR, FIXED_RR, CMRR.
-Bring the cmmr attributes in vrr struct.
-Remove condition flipline > vmin for LNL.
-Account for vmax being 0 based while MSA vtotal being 1 based.
Rev7:
I have added patches from series for AS SDP fixes [1] , as without panels
that support AS SDP gives a lot of issues.
There were major changes in design as discussed in last version [2].
Below are the change logs:
-Change the design to compute vrr state based on actual uapi.vrr.enable
knob. So when that knob is disabled we always compute vmin=flipline=vmax.
-Always set vmin=crtc_vtotal instead of the using the current refresh rate
based approach. This helps to have the same guardband while switching
between fixed and variable timings.
-Disable CMRR for now to reduce complexity while changing timings on the
fly.
-Change the state computation and add vmin/vmax/flipline reprogramming
to vrr_{enable,disable}()
-Introduce the fixed refresh mode from MTL instead of LNL.
[1] https://patchwork.freedesktop.org/series/137035/
[2] https://patchwork.kernel.org/project/intel-gfx/cover/20241111091221.2992818-1-ankit.k.nautiyal@xxxxxxxxx/
Rev8:
-Addressed review comments from Ville.
-Refactored few patches.
-Dropped patches:
1. "drm/i915/vrr: Adjust Vtotal for MSA for fixed timing"
2. "drm/i915/vrr: Avoid sending PUSH when VRR TG is used with Fixed
refresh rate"
Rev9:
-Fixed issue seen on BAT bugs.
Rev10:
-Drop patch for avoiding VRR for DP with HDMI panel.
-Address comments from Ville.
-Add VRR compute config for DP MST.
-Add HAS_VRR() checks and compute fixed timing for all VRR supporting
platforms.
-Move guardband and pipeline_full checks
out from the pure !fastset block in intel_pipe_config_compare().
Rev11:
-Addressed comments from Ville.
-Added only fixed_rr for Joiner.
-Use vrr_possible() before setting fixed timings and before setting
trans_vrr_ctl.
-Split patch to remove vrr.guardband/pipeline_full from !fastset block.
-Add patch to avoid writing into Vtotal.Vtotal bits when always using
VRRTG.
Ankit Nautiyal (22):
drm/i915/vrr: Remove unwanted comment
drm/i915:vrr: Separate out functions to compute vmin and vmax
drm/i915/vrr: Make helpers for cmrr and vrr timings
drm/i915/vrr: Disable CMRR
drm/i915/vrr: Track vrr.enable only for variable timing
drm/i915/vrr: Use crtc_vtotal for vmin
drm/i915/vrr: Prepare for fixed refresh rate timings
drm/i915/display: Enable MSA Ignore Timing PAR only when in not
fixed_rr mode
drm/i915/hdmi: Use VRR Timing generator for HDMI for fixed_rr
drm/i915/dp_mst: Use VRR Timing generator for DP MST for fixed_rr
drm/i915/display: Disable PSR before disabling VRR
drm/i915/display: Move intel_psr_post_plane_update() at the later
drm/i915/vrr: Refactor condition for computing vmax and LRR
drm/i915/vrr: Always set vrr vmax/vmin/flipline in
vrr_{enable/disable}
drm/i915/display: Use fixed_rr timings in modeset sequence
drm/i915/vrr: Use fixed timings for platforms that support VRR
drm/i915/display: Move vrr.guardband/pipeline_full out of !fastset
block
drm/i915/display: Use fixed rr timings in
intel_set_transcoder_timings_lrr()
drm/i915/vrr: Allow fixed_rr with pipe joiner
drm/i915/vrr: Always use VRR timing generator for MTL+
drm/i915/display: Add fixed_rr to crtc_state dump
drm/i915/display: Avoid use of VTOTAL.Vtotal bits
.../drm/i915/display/intel_crtc_state_dump.c | 3 +-
drivers/gpu/drm/i915/display/intel_ddi.c | 5 +
drivers/gpu/drm/i915/display/intel_display.c | 86 +++--
.../drm/i915/display/intel_dp_link_training.c | 15 +-
drivers/gpu/drm/i915/display/intel_dp_mst.c | 7 +
drivers/gpu/drm/i915/display/intel_hdmi.c | 3 +
drivers/gpu/drm/i915/display/intel_vrr.c | 326 ++++++++++++++----
drivers/gpu/drm/i915/display/intel_vrr.h | 6 +
8 files changed, 361 insertions(+), 90 deletions(-)
--
2.45.2
