Quoting Rodrigo Vivi (2023-10-05 12:13:34-03:00)
>On Thu, Oct 05, 2023 at 03:05:31AM -0400, Kahola, Mika wrote:
>> > -----Original Message-----
>> > From: Vivi, Rodrigo <rodrigo.vivi@xxxxxxxxx>
>> > Sent: Wednesday, October 4, 2023 3:56 PM
>> > To: Kahola, Mika <mika.kahola@xxxxxxxxx>
>> > Cc: intel-gfx@xxxxxxxxxxxxxxxxxxxxx
>> > Subject: Re: [PATCH] drm/i915/display: Reset message bus after each read/write operation
>> >
>> > On Wed, Oct 04, 2023 at 01:25:04PM +0300, Mika Kahola wrote:
>> > > Every know and then we receive the following error when running for
>> > > example IGT test kms_flip.
>> > >
>> > > [drm] *ERROR* PHY G Read 0d80 failed after 3 retries.
>> > > [drm] *ERROR* PHY G Write 0d81 failed after 3 retries.
>> > >
>> > > Since the error is sporadic in nature, the patch proposes to reset the
>> > > message bus after every successful or unsuccessful read or write
>> > > operation. However, testing revealed that this alone is not sufficient
>> > > method an additiona delay is also introduces anything from 200us to
>> > > 300us. This delay is experimental value and has no specification to
>> > > back it up.
>> >
>> > have you tried the delays without the bus_reset?
>> Yes, we have bumped up the delay, first from 0x100 to 0x200 and then as per
>> BSpec change 0xa000 and I have tried 0xf000. Increasing the timeout reduces
>> the frequency of this error but doesn't solve this issue.
>
>what is exactly this BSPec's 0xa000? where can I see it? So maybe you can
>update the message above removing the 'no specification to back it up'.
(Resending this because I got a delivery failure notification)
I think we are confusing "delay" with the "timeout parameter" of the msgbus.
The PHY has a register to control the timeout parameter of msgbus transactions
(BSpec 65156). It's default value is 0x100. With commit e028d7a4235d
("drm/i915/cx0: Check and increase msgbus timeout threshold"), we had integrated
a workaround that bumped the timeout value to 0x200 in case timeouts were
observed. Later on, there was a BSpec update with the formal timeout value to be
programmed to 0xa000, which was incorporated with commit e35628968032
("drm/i915/cx0: Add step for programming msgbus timer").
I *believe* what Rodrigo has asked was about the usleep_range() calls added with
this patch, if we tried to only keep the usleed_range() without the bus reset.
--
Gustavo Sousa
>
>Oh, and my english is bad, but it looks to me that 'empirical' might
>sound better than 'experimental' for this case, since you really did
>a lot of experiments before coming to this final conclusion.
>
>>
>> > have you talked to hw architects about this?
>> Yes, HW guys requested traces which I provided but based on these the sequence we use in i915
>> is correct.
>>
>> >
>> > I wonder if we should add the delay inside the bus_reset itself?
>> > although the bit 15 clear check should be enough by itself and it doesn't look like it is a hw/fw reset involved to justify the extra
>> > delay.
>> That should be enough. To me, it looks like when reading/writing to the bus maybe too fast, the hw cannot handle that and we need
>> to reset and let things settle down before trying again.
>>
>> >
>> > well, at least some /* FIXME: */ or /* XXX: */ comments is desired along with the messages if we are going with this hack without
>> > understanding why...
>> True, I will add these the the patch.
>>
>> Thanks for review!
>>
>> -Mika-
>> >
>> > >
>> > > Signed-off-by: Mika Kahola <mika.kahola@xxxxxxxxx>
>> > > ---
>> > > drivers/gpu/drm/i915/display/intel_cx0_phy.c | 6 ++++++
>> > > 1 file changed, 6 insertions(+)
>> > >
>> > > diff --git a/drivers/gpu/drm/i915/display/intel_cx0_phy.c
>> > > b/drivers/gpu/drm/i915/display/intel_cx0_phy.c
>> > > index abd607b564f1..a71b8a29d6b0 100644
>> > > --- a/drivers/gpu/drm/i915/display/intel_cx0_phy.c
>> > > +++ b/drivers/gpu/drm/i915/display/intel_cx0_phy.c
>> > > @@ -220,9 +220,12 @@ static u8 __intel_cx0_read(struct drm_i915_private *i915, enum port port,
>> > > /* 3 tries is assumed to be enough to read successfully */
>> > > for (i = 0; i < 3; i++) {
>> > > status = __intel_cx0_read_once(i915, port, lane, addr);
>> > > + intel_cx0_bus_reset(i915, port, lane);
>> > >
>> > > if (status >= 0)
>> > > return status;
>> > > +
>> > > + usleep_range(200, 300);
>> > > }
>> > >
>> > > drm_err_once(&i915->drm, "PHY %c Read %04x failed after %d
>> > > retries.\n", @@ -299,9 +302,12 @@ static void __intel_cx0_write(struct drm_i915_private *i915, enum port port,
>> > > /* 3 tries is assumed to be enough to write successfully */
>> > > for (i = 0; i < 3; i++) {
>> > > status = __intel_cx0_write_once(i915, port, lane, addr, data,
>> > > committed);
>> > > + intel_cx0_bus_reset(i915, port, lane);
>> > >
>> > > if (status == 0)
>> > > return;
>> > > +
>> > > + usleep_range(200, 300);
>> > > }
>> > >
>> > > drm_err_once(&i915->drm,
>> > > --
>> > > 2.34.1
>> > >
