[PATCH v3 1/2] drm/i915: Sanitycheck MMIO access early in driver load

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Matt Roper <matthew.d.roper@xxxxxxxxx>

We occasionally see the PCI device in a non-accessible state at the
point the driver is loaded.  When this happens, all BAR accesses will
read back as 0xFFFFFFFF.  Rather than reading registers and
misinterpreting their (invalid) values, let's specifically check for
0xFFFFFFFF in a register that cannot have that value to see if the
device is accessible.

Signed-off-by: Matt Roper <matthew.d.roper@xxxxxxxxx>
Cc: Mika Kuoppala <mika.kuoppala@xxxxxxxxxxxxxxx>
Reviewed-by: Andi Shyti <andi.shyti@xxxxxxxxxxxxxxx>
Signed-off-by: Andi Shyti <andi.shyti@xxxxxxxxxxxxxxx>
---
Hi,

Andrzej suggested to check the upper 16 bits of the BAR. But
after an offline discussion with Matt, we agreed that reading the
whole 32 bits is a safer choice.

Andi

 drivers/gpu/drm/i915/intel_uncore.c | 34 +++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_uncore.c b/drivers/gpu/drm/i915/intel_uncore.c
index e1e1f34490c8e..14ec45e6facfa 100644
--- a/drivers/gpu/drm/i915/intel_uncore.c
+++ b/drivers/gpu/drm/i915/intel_uncore.c
@@ -2602,11 +2602,45 @@ static int uncore_forcewake_init(struct intel_uncore *uncore)
 	return 0;
 }
 
+static int sanity_check_mmio_access(struct intel_uncore *uncore)
+{
+	struct drm_i915_private *i915 = uncore->i915;
+
+	if (GRAPHICS_VER(i915) < 8)
+		return 0;
+
+	/*
+	 * Sanitycheck that MMIO access to the device is working properly.  If
+	 * the CPU is unable to communcate with a PCI device, BAR reads will
+	 * return 0xFFFFFFFF.  Let's make sure the device isn't in this state
+	 * before we start trying to access registers.
+	 *
+	 * We use the primary GT's forcewake register as our guinea pig since
+	 * it's been around since HSW and it's a masked register so the upper
+	 * 16 bits can never read back as 1's if device access is operating
+	 * properly.
+	 *
+	 * If MMIO isn't working, we'll wait up to 2 seconds to see if it
+	 * recovers, then give up.
+	 */
+#define COND (__raw_uncore_read32(uncore, FORCEWAKE_MT) != ~0)
+	if (wait_for(COND, 2000) == -ETIMEDOUT) {
+		drm_err(&i915->drm, "Device is non-operational; MMIO access returns 0xFFFFFFFF!\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
 int intel_uncore_init_mmio(struct intel_uncore *uncore)
 {
 	struct drm_i915_private *i915 = uncore->i915;
 	int ret;
 
+	ret = sanity_check_mmio_access(uncore);
+	if (ret)
+		return ret;
+
 	/*
 	 * The boot firmware initializes local memory and assesses its health.
 	 * If memory training fails, the punit will have been instructed to
-- 
2.39.2




[Index of Archives]     [AMD Graphics]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux