From: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
Pull the scanline_offset calculation into its own function. Might
have further use for this later with DSB scanline waits.
Reviewed-by: Jani Nikula <jani.nikula@xxxxxxxxx>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@xxxxxxxxx>
Signed-off-by: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
---
drivers/gpu/drm/i915/display/intel_vblank.c | 89 +++++++++++----------
1 file changed, 48 insertions(+), 41 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_vblank.c b/drivers/gpu/drm/i915/display/intel_vblank.c
index 48bf3923af11..f8bf9810527d 100644
--- a/drivers/gpu/drm/i915/display/intel_vblank.c
+++ b/drivers/gpu/drm/i915/display/intel_vblank.c
@@ -441,6 +441,53 @@ void intel_wait_for_pipe_scanline_moving(struct intel_crtc *crtc)
wait_for_pipe_scanline_moving(crtc, true);
}
+static int intel_crtc_scanline_offset(const struct intel_crtc_state *crtc_state)
+{
+ struct drm_i915_private *i915 = to_i915(crtc_state->uapi.crtc->dev);
+ const struct drm_display_mode *adjusted_mode = &crtc_state->hw.adjusted_mode;
+
+ /*
+ * The scanline counter increments at the leading edge of hsync.
+ *
+ * On most platforms it starts counting from vtotal-1 on the
+ * first active line. That means the scanline counter value is
+ * always one less than what we would expect. Ie. just after
+ * start of vblank, which also occurs at start of hsync (on the
+ * last active line), the scanline counter will read vblank_start-1.
+ *
+ * On gen2 the scanline counter starts counting from 1 instead
+ * of vtotal-1, so we have to subtract one (or rather add vtotal-1
+ * to keep the value positive), instead of adding one.
+ *
+ * On HSW+ the behaviour of the scanline counter depends on the output
+ * type. For DP ports it behaves like most other platforms, but on HDMI
+ * there's an extra 1 line difference. So we need to add two instead of
+ * one to the value.
+ *
+ * On VLV/CHV DSI the scanline counter would appear to increment
+ * approx. 1/3 of a scanline before start of vblank. Unfortunately
+ * that means we can't tell whether we're in vblank or not while
+ * we're on that particular line. We must still set scanline_offset
+ * to 1 so that the vblank timestamps come out correct when we query
+ * the scanline counter from within the vblank interrupt handler.
+ * However if queried just before the start of vblank we'll get an
+ * answer that's slightly in the future.
+ */
+ if (DISPLAY_VER(i915) == 2) {
+ int vtotal;
+
+ vtotal = adjusted_mode->crtc_vtotal;
+ if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE)
+ vtotal /= 2;
+
+ return vtotal - 1;
+ } else if (HAS_DDI(i915) && intel_crtc_has_type(crtc_state, INTEL_OUTPUT_HDMI)) {
+ return 2;
+ } else {
+ return 1;
+ }
+}
+
void intel_crtc_update_active_timings(const struct intel_crtc_state *crtc_state)
{
struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc);
@@ -479,47 +526,7 @@ void intel_crtc_update_active_timings(const struct intel_crtc_state *crtc_state)
crtc->mode_flags = crtc_state->mode_flags;
- /*
- * The scanline counter increments at the leading edge of hsync.
- *
- * On most platforms it starts counting from vtotal-1 on the
- * first active line. That means the scanline counter value is
- * always one less than what we would expect. Ie. just after
- * start of vblank, which also occurs at start of hsync (on the
- * last active line), the scanline counter will read vblank_start-1.
- *
- * On gen2 the scanline counter starts counting from 1 instead
- * of vtotal-1, so we have to subtract one (or rather add vtotal-1
- * to keep the value positive), instead of adding one.
- *
- * On HSW+ the behaviour of the scanline counter depends on the output
- * type. For DP ports it behaves like most other platforms, but on HDMI
- * there's an extra 1 line difference. So we need to add two instead of
- * one to the value.
- *
- * On VLV/CHV DSI the scanline counter would appear to increment
- * approx. 1/3 of a scanline before start of vblank. Unfortunately
- * that means we can't tell whether we're in vblank or not while
- * we're on that particular line. We must still set scanline_offset
- * to 1 so that the vblank timestamps come out correct when we query
- * the scanline counter from within the vblank interrupt handler.
- * However if queried just before the start of vblank we'll get an
- * answer that's slightly in the future.
- */
- if (DISPLAY_VER(i915) == 2) {
- int vtotal;
-
- vtotal = adjusted_mode.crtc_vtotal;
- if (adjusted_mode.flags & DRM_MODE_FLAG_INTERLACE)
- vtotal /= 2;
-
- crtc->scanline_offset = vtotal - 1;
- } else if (HAS_DDI(i915) &&
- intel_crtc_has_type(crtc_state, INTEL_OUTPUT_HDMI)) {
- crtc->scanline_offset = 2;
- } else {
- crtc->scanline_offset = 1;
- }
+ crtc->scanline_offset = intel_crtc_scanline_offset(crtc_state);
spin_unlock(&i915->uncore.lock);
spin_unlock_irqrestore(&i915->drm.vblank_time_lock, irqflags);
--
2.39.2
