On 16/03/2022 07:37, Kasireddy, Vivek wrote:
Hi Tvrtko,
On 15/03/2022 07:28, Kasireddy, Vivek wrote:
Hi Tvrtko, Daniel,
On 11/03/2022 09:39, Daniel Vetter wrote:
On Mon, 7 Mar 2022 at 21:38, Vivek Kasireddy <vivek.kasireddy@xxxxxxxxx> wrote:
On platforms capable of allowing 8K (7680 x 4320) modes, pinning 2 or
more framebuffers/scanout buffers results in only one that is mappable/
fenceable. Therefore, pageflipping between these 2 FBs where only one
is mappable/fenceable creates latencies large enough to miss alternate
vblanks thereby producing less optimal framerate.
This mainly happens because when i915_gem_object_pin_to_display_plane()
is called to pin one of the FB objs, the associated vma is identified
as misplaced and therefore i915_vma_unbind() is called which unbinds and
evicts it. This misplaced vma gets subseqently pinned only when
i915_gem_object_ggtt_pin_ww() is called without PIN_MAPPABLE. This
results in a latency of ~10ms and happens every other vblank/repaint cycle.
Therefore, to fix this issue, we try to see if there is space to map
at-least two objects of a given size and return early if there isn't. This
would ensure that we do not try with PIN_MAPPABLE for any objects that
are too big to map thereby preventing unncessary unbind.
Testcase:
Running Weston and weston-simple-egl on an Alderlake_S (ADLS) platform
with a 8K@60 mode results in only ~40 FPS. Since upstream Weston submits
a frame ~7ms before the next vblank, the latencies seen between atomic
commit and flip event are 7, 24 (7 + 16.66), 7, 24..... suggesting that
it misses the vblank every other frame.
Here is the ftrace snippet that shows the source of the ~10ms latency:
i915_gem_object_pin_to_display_plane() {
0.102 us | i915_gem_object_set_cache_level();
i915_gem_object_ggtt_pin_ww() {
0.390 us | i915_vma_instance();
0.178 us | i915_vma_misplaced();
i915_vma_unbind() {
__i915_active_wait() {
0.082 us | i915_active_acquire_if_busy();
0.475 us | }
intel_runtime_pm_get() {
0.087 us | intel_runtime_pm_acquire();
0.259 us | }
__i915_active_wait() {
0.085 us | i915_active_acquire_if_busy();
0.240 us | }
__i915_vma_evict() {
ggtt_unbind_vma() {
gen8_ggtt_clear_range() {
10507.255 us | }
10507.689 us | }
10508.516 us | }
v2: Instead of using bigjoiner checks, determine whether a scanout
buffer is too big by checking to see if it is possible to map
two of them into the ggtt.
v3 (Ville):
- Count how many fb objects can be fit into the available holes
instead of checking for a hole twice the object size.
- Take alignment constraints into account.
- Limit this large scanout buffer check to >= Gen 11 platforms.
v4:
- Remove existing heuristic that checks just for size. (Ville)
- Return early if we find space to map at-least two objects. (Tvrtko)
- Slightly update the commit message.
v5: (Tvrtko)
- Rename the function to indicate that the object may be too big to
map into the aperture.
- Account for guard pages while calculating the total size required
for the object.
- Do not subject all objects to the heuristic check and instead
consider objects only of a certain size.
- Do the hole walk using the rbtree.
- Preserve the existing PIN_NONBLOCK logic.
- Drop the PIN_MAPPABLE check while pinning the VMA.
v6: (Tvrtko)
- Return 0 on success and the specific error code on failure to
preserve the existing behavior.
v7: (Ville)
- Drop the HAS_GMCH(i915), DISPLAY_VER(i915) < 11 and
size < ggtt->mappable_end / 4 checks.
- Drop the redundant check that is based on previous heuristic.
v8:
- Make sure that we are holding the mutex associated with ggtt vm
as we traverse the hole nodes.
v9: (Tvrtko)
- Use mutex_lock_interruptible_nested() instead of mutex_lock().
Cc: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
Cc: Maarten Lankhorst <maarten.lankhorst@xxxxxxxxxxxxxxx>
Cc: Tvrtko Ursulin <tvrtko.ursulin@xxxxxxxxxxxxxxx>
Cc: Manasi Navare <manasi.d.navare@xxxxxxxxx>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@xxxxxxxxx>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@xxxxxxxxx>
---
drivers/gpu/drm/i915/i915_gem.c | 128 +++++++++++++++++++++++---------
1 file changed, 94 insertions(+), 34 deletions(-)
diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c
index 9747924cc57b..e0d731b3f215 100644
--- a/drivers/gpu/drm/i915/i915_gem.c
+++ b/drivers/gpu/drm/i915/i915_gem.c
@@ -49,6 +49,7 @@
#include "gem/i915_gem_pm.h"
#include "gem/i915_gem_region.h"
#include "gem/i915_gem_userptr.h"
+#include "gem/i915_gem_tiling.h"
#include "gt/intel_engine_user.h"
#include "gt/intel_gt.h"
#include "gt/intel_gt_pm.h"
@@ -882,6 +883,96 @@ static void discard_ggtt_vma(struct i915_vma *vma)
spin_unlock(&obj->vma.lock);
}
+static int
+i915_gem_object_fits_in_aperture(struct drm_i915_gem_object *obj,
+ u64 alignment, u64 flags)
Tvrtko asked me to ack the first patch, but then I looked at this and
started wondering.
Conceptually this doesn't pass the smell test. What if we have
multiple per-crtc buffers? Multiple planes on the same crtc? What if
the app does triple buffer? You'll be forever busy tuning this
heuristics, which can't fundamentally be fixed I think. The old "half
of mappable" heuristic isn't really better, but at least it was dead
simple.
Imo what we need here is a change in approach:
1. Check whether the useable view for scanout exists already. If yes,
use that. This should avoid the constant unbinding stalls.
2. Try to in buffer to mappabley, but without evicting anything (so
not the non-blocking thing)
3. Pin the buffer with the most lenient approach
Even the non-blocking interim stage is dangerous, since it'll just
result in other buffers (e.g. when triple-buffering) getting unbound
and we're back to the same stall. Note that this could have an impact
on cpu rendering compositors, where we might end up relying a lot more
partial views. But as long as we are a tad more aggressive (i.e. the
non-blocking binding) in the mmap path that should work out to keep
everything balanced, since usually you render first before you display
anything. And so the buffer should end up in the ideal place.
I'd try to first skip the 2. step since I think it'll require a bit of
work, and frankly I don't think we care about the potential fallout.
To be sure I understand, you propose to stop trying to pin mappable by default. Ie. stop
respecting this comment from i915_gem_object_pin_to_display_plane:
/*
* As the user may map the buffer once pinned in the display plane
* (e.g. libkms for the bootup splash), we have to ensure that we
* always use map_and_fenceable for all scanout buffers. However,
* it may simply be too big to fit into mappable, in which case
* put it anyway and hope that userspace can cope (but always first
* try to preserve the existing ABI).
*/
[Kasireddy, Vivek] Digging further, this is what the commit message that added
the above comment says:
commit 2efb813d5388e18255c54afac77bd91acd586908
Author: Chris Wilson <chris@xxxxxxxxxxxxxxxxxx>
Date: Thu Aug 18 17:17:06 2016 +0100
drm/i915: Fallback to using unmappable memory for scanout
The existing ABI says that scanouts are pinned into the mappable region
so that legacy clients (e.g. old Xorg or plymouthd) can write directly
into the scanout through a GTT mapping. However if the surface does not
fit into the mappable region, we are better off just trying to fit it
anywhere and hoping for the best. (Any userspace that is capable of
using ginormous scanouts is also likely not to rely on pure GTT
updates.) With the partial vma fault support, we are no longer
restricted to only using scanouts that we can pin (though it is still
preferred for performance reasons and for powersaving features like
FBC).
By a quick look, for this case it appears we would end up creating partial views for
CPU
access (since the normal mapping would be busy/unpinnable). Worst case for this is to
create a bunch of 1MiB VMAs so something to check would be how long those persist
in
memory before they get released. Or perhaps the bootup splash use case is not common
these days?
[Kasireddy, Vivek] AFAIK, Plymouth is still the default bootup splash service on Fedora,
Ubuntu and most other distributions. And, I took a quick look at it and IIUC, it
(Plymouth's
drm plugin) seems to create a dumb FB, mmap and update it via the dirty_fb ioctl. This
would not to be a problem on ADL-S where there is space in mappable for one 8K FB.
FBC is a good point - correct me if I am wrong, but if we dropped trying
to map in aperture by default it looks like we would lose it and that
would be a significant power regression. In which case it doesn't seem
like that would be an option.
[Kasireddy, Vivek] Ok, makes sense.
Which I think leaves us with _some_ heuristics in any case.
1) N-holes heuristics.
2) Don't ever try PIN_MAPPABLE for framebuffers larger than some
percentage of aperture.
Could this solve the 8k issue, most of the time, maybe? Could the
current "aperture / 2" test be expressed generically in some terms? Like
"(aperture - 10% (or some absolute value)) / 2" to account for non-fb
objects? I forgot what you said the relationship between aperture size
and 8k fb size was.
3) Don't evict for PIN_MAPPABLE mismatches when
i915_gem_object_ggtt_pin_ww->i915_vma_misplaced is called on behalf of
i915_gem_object_pin_to_display_plane. Assumption being if we ended up
with a non-mappable fb to start with, we must not try to re-bind it or
we risk ping-pong latencies.
The last would I guess need to distinguish between PIN_MAPPABLE passed
in versus opportunistically added by i915_gem_object_pin_to_display_plane.
How intrusive would it be to implement this option I am not sure without
trying myself.
[Kasireddy, Vivek] I suspect I might be missing something, but could it not be
as simple as below:
@@ -940,7 +940,8 @@ i915_gem_object_ggtt_pin_ww(struct drm_i915_gem_object *obj,
return ERR_PTR(-ENOSPC);
if (flags & PIN_MAPPABLE &&
- vma->fence_size > ggtt->mappable_end / 2)
+ (vma->fence_size > ggtt->mappable_end / 2 ||
+ !i915_vma_is_map_and_fenceable(vma)))
return ERR_PTR(-ENOSPC);
}
Looks like this would work...
Given this, do you think it would work if we just preserve the existing behavior and
tweak the heuristic introduced in this patch to look for space in aperture for only
one FB instead of two? Or, is there no good option for solving this issue other than
to create 1MB VMAs?
I did not get how having one hole would solve the issue. Wouldn't it
still hit the re-bind ping-pong? Or there isn't even a single hole for
8k fb typically?
[Kasireddy, Vivek] IIUC, Mesa gives Weston a max of 4 backbuffers but it
almost always uses only 2 except when it needs to share the FB -- with a plugin
such as "remoting" for desktop streaming.
Given the common use-case, lets assume there are two 8K FBs: FB1 and FB2
FB1 is mappable/fenceable and therefore not misplaced.
FB2 is NOT mappable and hence identified as misplaced
(because it fails the check
(flags & PIN_MAPPABLE && !i915_vma_is_map_and_fenceable(vma))
As you suggest in 3) above the goal is to ensure that FB2 does not get evicted
when we try to pin with PIN_MAPABBLE -- after it gets identified as misplaced.
Or, alternatively, when we pin with PIN_MAPABBLE, we could just check to
see if there is space in aperture for only FB2 (N = 1) and return early -- before
even getting to i915_vma_misplaced(). As you can see, we avoid the ping-pong
issue in both these cases.
... got it, yes, it seems both approaches works for this use case.
Not sure that I have a preference between the two approaches at this point.
Both would be behind a "PIN_MAPPABLE && PIN_NONBLOCK" check, so both
would only apply to opportunistic PIN_MAPPABLE attempts. That is, any
caller who only passes PIN_MAPPABLE would be unaffected which is what we
want.
The extra i915_vma_is_map_and_fenceable check I guess is simpler and
self-contained. I assume you have a test setup and can try it out to
check it really works?
The current version of this patch -- when running Weston -- puts both FB1
and FB2 (N = 2) outside of aperture although there may be space for FB1.
I don't think this makes sense anymore given Plymouth's single-buffer
use-case that uses dirtyfb ioctl.
Yes agreed, it sounds preferable to preserve the current behaviour there.
Regards,
Tvrtko
