On 2/25/2022 10:29, Tvrtko Ursulin wrote:
On 25/02/2022 18:01, John Harrison wrote:
On 2/25/2022 09:39, Tvrtko Ursulin wrote:
On 25/02/2022 17:11, John Harrison wrote:
On 2/25/2022 08:36, Tvrtko Ursulin wrote:
On 24/02/2022 20:02, John Harrison wrote:
On 2/23/2022 04:00, Tvrtko Ursulin wrote:
On 23/02/2022 02:22, John Harrison wrote:
On 2/22/2022 01:53, Tvrtko Ursulin wrote:
On 18/02/2022 21:33, John.C.Harrison@xxxxxxxxx wrote:
From: John Harrison <John.C.Harrison@xxxxxxxxx>
Compute workloads are inherently not pre-emptible on current
hardware.
Thus the pre-emption timeout was disabled as a workaround to
prevent
unwanted resets. Instead, the hang detection was left to the
heartbeat
and its (longer) timeout. This is undesirable with GuC
submission as
the heartbeat is a full GT reset rather than a per engine
reset and so
is much more destructive. Instead, just bump the pre-emption
timeout
Can we have a feature request to allow asking GuC for an
engine reset?
For what purpose?
To allow "stopped heartbeat" to reset the engine, however..
GuC manages the scheduling of contexts across engines. With
virtual engines, the KMD has no knowledge of which engine a
context might be executing on. Even without virtual engines,
the KMD still has no knowledge of which context is currently
executing on any given engine at any given time.
There is a reason why hang detection should be left to the
entity that is doing the scheduling. Any other entity is second
guessing at best.
The reason for keeping the heartbeat around even when GuC
submission is enabled is for the case where the KMD/GuC have
got out of sync with either other somehow or GuC itself has
just crashed. I.e. when no submission at all is working and we
need to reset the GuC itself and start over.
.. I wasn't really up to speed to know/remember heartbeats are
nerfed already in GuC mode.
Not sure what you mean by that claim. Engine resets are handled
by GuC because GuC handles the scheduling. You can't do the
former if you aren't doing the latter. However, the heartbeat is
still present and is still the watchdog by which engine resets
are triggered. As per the rest of the submission process, the
hang detection and recovery is split between i915 and GuC.
I meant that "stopped heartbeat on engine XXX" can only do a full
GPU reset on GuC.
I mean that there is no 'stopped heartbeat on engine XXX' when i915
is not handling the recovery part of the process.
Hmmmm?
static void
reset_engine(struct intel_engine_cs *engine, struct i915_request *rq)
{
if (IS_ENABLED(CONFIG_DRM_I915_DEBUG_GEM))
show_heartbeat(rq, engine);
if (intel_engine_uses_guc(engine))
/*
* GuC itself is toast or GuC's hang detection
* is disabled. Either way, need to find the
* hang culprit manually.
*/
intel_guc_find_hung_context(engine);
intel_gt_handle_error(engine->gt, engine->mask,
I915_ERROR_CAPTURE,
"stopped heartbeat on %s",
engine->name);
}
How there is no "stopped hearbeat" in guc mode? From this code it
certainly looks there is.
Only when the GuC is toast and it is no longer an engine reset but a
full GT reset that is required. So technically, it is not a 'stopped
heartbeat on engine XXX' it is 'stopped heartbeat on GT#'.
You say below heartbeats are going in GuC mode. Now I totally don't
understand how they are going but there is allegedly no "stopped
hearbeat".
Because if GuC is handling the detection and recovery then i915 will
not reach that point. GuC will do the engine reset and start
scheduling the next context before the heartbeat period expires. So
the notification will be a G2H about a specific context being reset
rather than the i915 notification about a stopped heartbeat.
intel_gt_handle_error(engine->gt, engine->mask,
I915_ERROR_CAPTURE,
"stopped heartbeat on %s",
engine->name);
intel_gt_handle_error:
/*
* Try engine reset when available. We fall back to full reset if
* single reset fails.
*/
if (!intel_uc_uses_guc_submission(>->uc) &&
intel_has_reset_engine(gt) && !intel_gt_is_wedged(gt)) {
local_bh_disable();
for_each_engine_masked(engine, gt, engine_mask, tmp) {
You said "However, the heartbeat is still present and is still the
watchdog by which engine resets are triggered", now I don't know
what you meant by this. It actually triggers a single engine reset
in GuC mode? Where in code does that happen if this block above
shows it not taking the engine reset path?
i915 sends down the per engine pulse.
GuC schedules the pulse
GuC attempts to pre-empt the currently active context
GuC detects the pre-emption timeout
GuC resets the engine
The fundamental process is exactly the same as in execlist mode.
It's just that the above blocks of code (calls to
intel_gt_handle_error and such) are now inside the GuC not i915.
Without the heartbeat going ping, there would be no context
switching and thus no pre-emption, no pre-emption timeout and so no
hang and reset recovery. And GuC cannot sent pulses by itself - it
has no ability to generate context workloads. So we need i915 to
send the pings and to gradually raise their priority. But the back
half of the heartbeat code is now inside the GuC. It will simply
never reach the i915 side timeout if GuC is doing the recovery
(unless the heartbeat's final period is too short). We should only
reach the i915 side timeout if GuC itself is toast. At which point
we need the full GT reset to recover the GuC.
If workload is not preempting and reset does not work, like engine
is truly stuck, does the current code hit "stopped heartbeat" or not
in GuC mode?
Hang on, where did 'reset does not work' come into this?
If GuC is alive and the hardware is not broken then no, it won't.
That's the whole point. GuC does the detection and recovery. The KMD
will never reach 'stopped heartbeat'.
If the hardware is broken and the reset does not work then GuC will
send a 'failed reset' notification to the KMD. The KMD treats that as
a major error and immediately does a full GT reset. So there is still
no 'stopped heartbeat'.
If GuC has died (or a KMD bug has caused sufficient confusion to make
it think the GuC has died) then yes, you will reach that code. But in
that case it is not an engine reset that is required, it is a full GT
reset including a reset of the GuC.
Got it, so what is actually wrong is calling intel_gt_handle_error
with an engine->mask in GuC mode. intel_engine_hearbeat.c/reset_engine
should fork into two (in some way), depending on backend, so in the
case of GuC it can call a variant of intel_gt_handle_error which would
be explicitly about a full GPU reset only, instead of a sprinkle of
intel_uc_uses_guc_submission in that function. Possibly even off load
the reset to a single per gt worker, so that if multiple active
engines trigger the reset roughly simultaneously, there is only one
full GPU reset. And it gets correctly labeled as "dead GuC" or something.
Sure. Feel free to re-write the reset code yet again. That's another
exceedingly fragile area of the driver.
However, that is unrelated to this patch set.
John.
Regards,
Tvrtko
