N.b. we need to figure out what the reported TGL CI issues were that
caused this to be reverted originally. Looks like there was no
follow-up?
BR,
Jani.
On Tue, 22 Jun 2021, Jani Nikula <jani.nikula@xxxxxxxxx> wrote:
> From: Matt Atwood <matthew.s.atwood@xxxxxxxxx>
>
> intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
> use before intel_encoder->type is set. This causes incorrect max source
> rate to be used for display 11+. On EHL and JSL, HBR3 is used instead of
> HBR2, and on the other affected platforms, HBR2 is used instead of HBR3.
>
> Move intel_dp_set_source_rates() to after intel_encoder->type is
> set. Add comment to intel_dp_is_edp() describing unsafe usages. Cleanup
> intel_dp_init_connector() while at it.
>
> Note: The same change was originally added as commit 680c45c767f6
> ("drm/i915/dp: Correctly advertise HBR3 for GEN11+"), but later reverted
> due to issues in CI in commit d3913019602e ("Revert "drm/i915/dp:
> Correctly advertise HBR3 for GEN11+"").
>
> v2: Alter intel_dp_set_source_rates final position (Ville/Manasi).
> Remove outdated comment (Ville).
> Slight optimization of control flow in intel_dp_init_connector.
> Slight rewording in commit message.
>
> Cc: Uma Shankar <uma.shankar@xxxxxxxxx>
> Signed-off-by: Matt Atwood <matthew.s.atwood@xxxxxxxxx>
> Reviewed-by: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> Signed-off-by: José Roberto de Souza <jose.souza@xxxxxxxxx>
> [Jani: Expand on the commit message.]
> Signed-off-by: Jani Nikula <jani.nikula@xxxxxxxxx>
> ---
> drivers/gpu/drm/i915/display/intel_dp.c | 28 ++++++++++---------------
> 1 file changed, 11 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
> index 6cc03b9e4321..41130aa4b191 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -100,6 +100,8 @@ static const u8 valid_dsc_slicecount[] = {1, 2, 4};
> *
> * If a CPU or PCH DP output is attached to an eDP panel, this function
> * will return true, and false otherwise.
> + *
> + * This function is not safe to use prior to encoder type being set.
> */
> bool intel_dp_is_edp(struct intel_dp *intel_dp)
> {
> @@ -5301,8 +5303,6 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
> intel_encoder->base.name))
> return false;
>
> - intel_dp_set_source_rates(intel_dp);
> -
> intel_dp->reset_link_params = true;
> intel_dp->pps.pps_pipe = INVALID_PIPE;
> intel_dp->pps.active_pipe = INVALID_PIPE;
> @@ -5318,28 +5318,22 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
> */
> drm_WARN_ON(dev, intel_phy_is_tc(dev_priv, phy));
> type = DRM_MODE_CONNECTOR_eDP;
> + intel_encoder->type = INTEL_OUTPUT_EDP;
> +
> + /* eDP only on port B and/or C on vlv/chv */
> + if (drm_WARN_ON(dev, (IS_VALLEYVIEW(dev_priv) ||
> + IS_CHERRYVIEW(dev_priv)) &&
> + port != PORT_B && port != PORT_C))
> + return false;
> } else {
> type = DRM_MODE_CONNECTOR_DisplayPort;
> }
>
> + intel_dp_set_source_rates(intel_dp);
> +
> if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
> intel_dp->pps.active_pipe = vlv_active_pipe(intel_dp);
>
> - /*
> - * For eDP we always set the encoder type to INTEL_OUTPUT_EDP, but
> - * for DP the encoder type can be set by the caller to
> - * INTEL_OUTPUT_UNKNOWN for DDI, so don't rewrite it.
> - */
> - if (type == DRM_MODE_CONNECTOR_eDP)
> - intel_encoder->type = INTEL_OUTPUT_EDP;
> -
> - /* eDP only on port B and/or C on vlv/chv */
> - if (drm_WARN_ON(dev, (IS_VALLEYVIEW(dev_priv) ||
> - IS_CHERRYVIEW(dev_priv)) &&
> - intel_dp_is_edp(intel_dp) &&
> - port != PORT_B && port != PORT_C))
> - return false;
> -
> drm_dbg_kms(&dev_priv->drm,
> "Adding %s connector on [ENCODER:%d:%s]\n",
> type == DRM_MODE_CONNECTOR_eDP ? "eDP" : "DP",
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
