Hi
2013/2/26 Paulo Zanoni <przanoni at gmail.com>:
> Hi
>
> 2013/2/25 Rodrigo Vivi <rodrigo.vivi at gmail.com>:
>> Yet according to pm spec pcode read/write operations
>> aren't necessary for HSW.
>>
>> Signed-off-by: Rodrigo Vivi <rodrigo.vivi at gmail.com>
>
> Reviewed-by: Paulo Zanoni <paulo.r.zanoni at intel.com>
Where's the "undo send email" button?
drivers/gpu/drm/i915/intel_pm.c:2674:9: warning: unused variable ?ret?
[-Wunused-variable]
drivers/gpu/drm/i915/intel_pm.c:2671:15: warning: unused variable
?pcu_mbox? [-Wunused-variable]
drivers/gpu/drm/i915/intel_pm.c:2671:6: warning: unused variable
?rc6vids? [-Wunused-variable]
>
>> ---
>> drivers/gpu/drm/i915/intel_pm.c | 26 --------------------------
>> 1 file changed, 26 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
>> index 322c562..761be6f 100644
>> --- a/drivers/gpu/drm/i915/intel_pm.c
>> +++ b/drivers/gpu/drm/i915/intel_pm.c
>> @@ -2749,18 +2749,6 @@ static void hsw_enable_rps(struct drm_device *dev)
>> GEN6_RP_UP_BUSY_AVG |
>> GEN7_RP_DOWN_IDLE_AVG);
>>
>> - ret = sandybridge_pcode_write(dev_priv, GEN6_PCODE_WRITE_MIN_FREQ_TABLE, 0);
>> - if (!ret) {
>> - pcu_mbox = 0;
>> - ret = sandybridge_pcode_read(dev_priv, GEN6_READ_OC_PARAMS, &pcu_mbox);
>> - if (ret && pcu_mbox & (1<<31)) { /* OC supported */
>> - dev_priv->rps.max_delay = pcu_mbox & 0xff;
>> - DRM_DEBUG_DRIVER("overclocking supported, adjusting frequency max to %dMHz\n", pcu_mbox * 50);
>> - }
>> - } else {
>> - DRM_DEBUG_DRIVER("Failed to set the min frequency\n");
>> - }
>> -
>> gen6_set_rps(dev_priv->dev, (gt_perf_status & 0xff00) >> 8);
>>
>> /* requires MSI enabled */
>> @@ -2772,20 +2760,6 @@ static void hsw_enable_rps(struct drm_device *dev)
>> /* enable all PM interrupts */
>> I915_WRITE(GEN6_PMINTRMSK, 0);
>>
>> - rc6vids = 0;
>> - ret = sandybridge_pcode_read(dev_priv, GEN6_PCODE_READ_RC6VIDS, &rc6vids);
>> - if (IS_GEN6(dev) && ret) {
>> - DRM_DEBUG_DRIVER("Couldn't check for BIOS workaround\n");
>> - } else if (IS_GEN6(dev) && (GEN6_DECODE_RC6_VID(rc6vids & 0xff) < 450)) {
>> - DRM_DEBUG_DRIVER("You should update your BIOS. Correcting minimum rc6 voltage (%dmV->%dmV)\n",
>> - GEN6_DECODE_RC6_VID(rc6vids & 0xff), 450);
>> - rc6vids &= 0xffff00;
>> - rc6vids |= GEN6_ENCODE_RC6_VID(450);
>> - ret = sandybridge_pcode_write(dev_priv, GEN6_PCODE_WRITE_RC6VIDS, rc6vids);
>> - if (ret)
>> - DRM_ERROR("Couldn't fix incorrect rc6 voltage\n");
>> - }
>> -
>> gen6_gt_force_wake_put(dev_priv);
>> }
>>
>> --
>> 1.8.1.2
>>
>> _______________________________________________
>> Intel-gfx mailing list
>> Intel-gfx at lists.freedesktop.org
>> http://lists.freedesktop.org/mailman/listinfo/intel-gfx
>
>
>
> --
> Paulo Zanoni
--
Paulo Zanoni
